Search Documents

By W. H. Forbes

As permissible explosives and electric detonators are now generally recognized as the only safe means of blasting in coal mines, this paper is limited to their use. Causes of Misfires There are many different causes of misfires, but the principal ones are as follows: 1. Explosives which have deteriorated through improper storage either at the storage magazine, the distributing magazine, or at the working face. This is not only true of the explosive itself, but also of its detonating agent. 2. Improper priming and charging at the working face. This commonly occurs when the explosives are handled by inexperienced persons. 3. Improper methods of tamping; the leg wires of the detonator may be abraded or broken by the tamping bar or stick, thereby causing a short or broken circuit. 4. Faulty leading wire, or electrical apparatus of insufficient strength to explode the detonator. Prevention of Misfires Storage is an important factor, especially with permissibles of a nitrate or ammonia base. Both explosives and detonators should be stored in substantially built, fire-resisting magazines and should be situated so that the minimum amount of moisture and heat is present. They should be so constructed that a constant supply of fresh air enters; the floor of the magazine should be raised to permit the circulation of air under the stored explosives. Boxes should be stored top side up and in such a manner that the old explosives are used before those of a later delivery. This eliminates chance of deterioration from lengthy storage. Detonators should be similarly handled and stored. The distributing magazine stock should be regulated so that not more than one day's supply is on hand.

Jan 1, 1930

By T. D. Yensen, N. A. Ziegler

AGING is a term that connotes a slow change in properties under ordinary operating conditions. It can be accelerated by increasing the temperature and by mechanical straining. The magnetic properties of iron and some of its alloys have for many years been known to be subject to such a change. But the cause of the change was not recognized until a few years ago after mechanical age-hardening in nonferrous alloys of the "duralumin" type had been definitely shown, by means of solid solubility curves, changes in electrical resistance and microanalysis, to be caused by slow precipitation of one or more constituents from the solid solution. The similarity between the solid solubility curves of such alloys (Fig. 1) and those for iron-nitrogen (Fig. 2) and iron-carbon alloys (Fig. 3) below the Al transformation point suggested at once that magnetic aging of iron might be caused by a similar process; namely, by the slow precipitation of carbon and nitrogen in the form of Fe4N and Fe3C at ordinary temperatures because of a cooling rate that had been too rapid to permit complete precipitation according to equilibrium conditions. This suggestion has since been amply confirmed, particularly by the comprehensive work of Köster1 on the effect of nitrogen and carbon. Typical curves are shown in Fig. 4 for the relationship between aging temperature and coercive force. Previous to the establishment of the precipitation-hardening theory it was thought that the effect of nonmetallic elements like C, N, 0, etc., on the magnetic properties of iron was greatest when these elements were retained in solid solution, atomically dispersed throughout the interstitial spaces of the iron lattice2.

Jan 1, 1935

By Eckley B. Coxe

IN the anthracite coal regions of Pennsylvania the custom has been to sight either at an open light (generally a mine-lamp), or at the string of a plumb-bob. If the station was intended to he a permanent one, a spud, as it is called, that is, a nail resembling a horseshoe nail with a hole in the head, is driven into the timbers over the station, or, if there be no timber, a hole is drilled in the coal or rock roof, into which a wooden plug is driven, which serves to hold the spud. The first operation in making a survey is to lay out the stations, that is, to mark the place where the holes are to be drilled for the plugs or the points on the timbers where the spuds are to be driven in. This should be done before any instrumental work is begun, as much labor can generally be spared, and the use of very short sights can often be avoided, by carefully laying out the stations beforehand. When the stations were laid out, a plumb-bob was hung from the innermost spud, which I will call No. 1, the instrument was put in position at No. 2, by plumbing down and putting a centre-pin under the spud, and then setting up over the centre-pin, and another plumb-bob was suspended from No. 3. If great accuracy was not required, a mine-lamp was set up under the plumbbobs, at No. 1 and No. 3, and the engineer sighted at them. If great accuracy was required, a lamp or some white sbface was held by an assistant behind the strings of the plumb-bobs. To work with any speed by the latter method (i. e., the accurate one), it was necessary for the engineer to have three assistants on whom he could rely even when the chaining was done afterwards; viz. : one to hold the light behind the string at No. 1, one at No. 3, and an assistant at the instrument to hold the light while levelling, reading the in

By Eckley B. Coxe

IN the anthracite coal regions of Pennsylvania the custom has been to sight either at an open light (generally a mine-lamp), or at the string of a plumb-bob. If the station was intended to be a permanent one, a spud, as it is called, that is, a nail resembling a horseshoe nail with a hole in the head, is driven into the timbers over the station, or, if there be no timber, a hole is drilled in the coal or rock roof, into which a wooden plug is driven, which serves to hold the spud. The first operation in making a survey is to lay out the stations, that is, to mark the place where the holes are to be drilled for the plugs or the points on the timbers where the spuds are to be driven in. This should be done before any instrumental work is begun, as much labor can generally be spared, and the use of very short sights can often be avoided, by carefully laying out the stations beforehand. When the stations were laid out, a plumb-bob was hung from the innermost spud, which I will call No. 1, the instrument was put in position at No. 2, by plumbing down and putting a centre-pin under the spud, and then setting up over the centre-pin, and another plumb-bob was suspended from No. 3. If great accuracy was not required, a mine-lamp was set up under the plumb-bobs, at No. 1 and No. 3, and the engineer sighted at them. If great accuracy was required, a lamp or some white surface was held by an assistant behind the strings of the plumb-bobs. To work with any speed by the latter method (i. e., the accurate one), it was necessary for the engineer to have three assistants on whom he could rely even when the chaining was done afterwards; viz.: one to hold the light behind the string at No. 1, one at No. 3, and an assistant at the instrument to hold the light while levelling, reading the in-

Jan 1, 1873

By K. C. Gilbart, Edgar Stansfield

When plants decay in a peat bog the woody parts form a brown pasty mass, or peat muck, largely soluble in alkalis. This brown matter has been termed "ulmin." The same material, but commonly black in color, is found in coal, and there is evidence of the similarity between the material forming the main bulk of the coal and the bulk of the more recently decayed material in peat bogs. The more recent or low-rank coals, such as lignite, little removed from the peat stage, contain notable percentages of alkali-soluble ulmins, but the percentage decreases with increased degree of coalification and is negligible in bituminous or higher rank coals. The determination of the alkali-soluble ulmins in any coal gives, therefore, an indication of its degree of coalification or rank. Coals which contain few or no ulmins soluble in alkalis do contain ulmins which can be rendered soluble by oxidation. The higher the rank of the coal, the more difficult it is to oxidize the insoluble ulmins and make them soluble. High-rank coals can be differentiated by oxidation tests on the insoluble ulmins; but low-rank coals can be characterized by both their soluble and insoluble ulmins. This paper deals with the determination and significance of the alkali-soluble ulmins present as such in the coal. The chemical nature and composition of ulmins are not discussed. Review of Literature The history of the study of ulmin is well given by Stopes and Wheeler.' The action of potash on coal has long been known, as Braconnot in 1819 distinguished between lignites and bituminous coals by stating that the former gave colored solutions with potash. Later the intensity of color was used to give a fuller differentiation. Hoffman2 distinguished between lignites and lignitic coals by the darker color given by the

Jan 1, 1932

The passing of Benjamin Bowden Lawrence in January, 1921, was a distinct loss to the engineering profession. Mr. Lawrence had a genius for reviving abandoned mines and developing them into substantial producers. A notable example of his work in this line was the Dives-Pelican near Georgetown, Colo. While on an exploring expedition in 1888, he examined this old mine and was convinced that bonanza ore still existed there. He located the owners of the property, and induced them to place sufficient capital at his disposal to enable him to re-open and explore this mine. So confident was he of the outcome that he undertook this work on a profit-sharing basis without salary. Within eighteen months the old Dives-Pelican was operating profitably, and for the following ten years it paid very substantial dividends. The late Theodore N. Vail was one of the owners of this old mine, and many years later, at a dinner given to Mr. Lawrence by the Alumni of Columbia University, Mr. Vail told the story of the resuscitation of the Dives-Pelican by Mr. Lawrence, and declared that the dividends he himself had received provided a large part of the funds that made possible the realization of his dream of establishing the long-distance telephone in this country. The E1 Cobre mines at Santiago de Cuba also owed their renewed life to Mr. Lawrence. Under his management, these mines produced and shipped several million pounds of copper per year. He was for several years consulting engineer for the Kerr Lake and other silver mines in the Cobalt region; the Kerr Lake became famous as a silver producer. Mr. Lawrence spent more than twenty years of his life in the mining camps of the West. He was but twenty-one years of age, and only a few months out of college, when he was appointed manager of the great Chautauqua Lode (a silver mine) located on Glacier Mountain near Montezuma, Colo. Here, isolated in the mountains for several months each year by ice and snow, he worked for five years to make these mines Pay. He possessed unusual breadth of vision and human understanding; he had ''personality plus," and when he opened an office in New York City as consulting engineer he quickly rose to an enviable position in his profession. Young engineers worked with enthusiasm under his guidance. He carefully selected his men, discussed fully with them the plans and policies to be pursued, then left them free to accomplish results in their own way. This attitude developed individuality and resourceful-

Jan 1, 1922

By Nelson W. Taylor

With the extensive deposits of potash minerals which have been discovered in the southwestern states, and their rapid development, a permanent American supply of potassium compounds is now assured. The 325-year history of the potash industry in this country has been told by H. I. Smith1, of the U.S. Geological Survey, and the more recent activities of the Survey and of American potash companies were described last year by the same author2. In fact, it may be stated that so great is the productive capacity that two mines in New Mexico and one in California are able to supply more than half a million tons of crude and refined salts over and above that produced for agricultural purposes. The era of scarcity has given way to an era of superabundance. This situatiori makes it desirable for the potash producer to look for other applications for his product, and it is with this in mind that the writer presents some information pertaining to present and possible future uses for potassium compounds in the ceramic industry. Ceramic Products Ceramic products are essentially solid materials containing one or more oxides such as SiO2, Al2O3, CaO, MgO, FeO, K2O, Na2O, TiO2, which are the oxides of greatest abundance in the earth's crust. The typical ceramic process is that of firing or burning the batch, and the product may be glassy, crystalline or mixed. In the glassy or vitreous group come glass, porcelain enamel and glazes; in the crystalline group, refractory materials such as silica brick, or chromite or magnesia; and in the mixed group, porcelain, chinaware, stoneware, tile, brick, etc., which contain both a vitreous and a crystalline phase, in variable proportions. The ceramic industry of the United States is a billion dollar industry, and is important not only because of its magnitude but also because of the key position occupied by certain ceramic products in the whole manufacturing structure. From the standpoint of use of potash, the field of refractories is of no great interest, since K2O lowers the melting point of a refractory oxide and

Jan 1, 1938

DEPENDENCY on foreign sources for many mineral raw materials is a characteristic of our economy which is becoming painfully evident. Although investment in foreign mining projects has increased, it has not kept up with the growing demand for foreign minerals. The sphere of American investment capital in mining ventures abroad has been severely limited by the rise of nationalism in many underdeveloped countries. Consequently, we can look back over half a century in which mining investment, exclusive of petroleum, has increased by 50 pct whereas other American investments abroad have multiplied by better than 300 pct. Investment in foreign mining or petroleum encounters different problems than capital investment for other industries. It is rarely invested in industrialized nations. Most of it goes to countries with expanding frontiers, like Canada, or to underdeveloped nations like Liberia. It must be used for building communities, recruiting and training labor, and establishing lines of communication and transportation. These complications are an accepted part of the mining game. However, the most complex problem is in those countries which consider mineral exploitation a usurpation of the people's natural heritage. This is a characteristic of the young government existing by a tenuous balance of power in an underdeveloped nation. American mining capital understandably has shunned these nations as being poor investment risks. However, they possess minerals which are needed by industry. Our government has attempted to stimulate mineral supplies beyond those provided from abroad by private capital. ECA, now under DMPA, makes loans to foreign mining companies. Since the ECA program cannot be expected to continue indefinitely, Point IV seems to be the logical next step to encourage foreign countries to fill our shortages. However, only 1 pct of the $35 million budget provided in the first year for Point IV was alloted for mining programs. Considering the need for minerals and the difficulties of procuring them by private investment, a larger share is needed and justifiable. Those who have been engaged in foreign mining can vouch for the fact that it takes many decades to teach the complex technology and economics of mining to the natives of under-developed countries. For this reason Point IV must be considered a long range program. Mineral requirements for the present must be met by more direct measures. Encouragement of private investment in foreign mining by such incentives as tax relief on profits from foreign sources, international bank-borrowing facilities for private capital, and diplomatic assistance in encouraging foreign countries to cooperate are imperative for our future mineral security.

Jan 1, 1952

By A. J. Erickson, W. J. Garmoe

In mid-1970, Park City Ventures, a Utah partnership of Asarco and the Anaconda Company, initiated a six-phase exploration and development program in the Park City District, Utah. Geologic studies had delineated a number of exploration targets in several areas of the district. Discovery of ore in any of the target areas and continued favorable downdip development below then productive ore bodies would allow for reserve expansion and mill construction. The targets were: replacement mineralization in the Mississippian Humbug formation below productive ore bodies on the east flank of the Park City anticline; replacement mineralization in the Humbug formation in an unexplored fault block in the footwall of the Hawkeye structure on the east flank of the anticline; vein and replacement mineralization along the Silver Fissure; potentially higher grade replacement mineralization in the Humbug formation in a theorized structural block on the west flank of the anticline beneath the Ontario vein; replacement mineralization in the Permian Park City formation in the West End shaft area of the Silver King mine; vein mineralization along the Back vein in the Judge mine. In 1971 the Judge and Silver King Projects were suspended, due to a 30% cutback in the exploration budget. In spite of the cutback additional reserves were developed below the Humbug East Flank ore bodies; a major zone of ore grade mineralization was discovered along the Silver Fissure, five new ore bodies were found in the Humbug and Doughnut formations on the west flank of the anticline beneath the Ontario vein. First concentrates were shipped from a new mill in May 1975.

Jan 1, 1979

By Michael Hoch, Daniel B. Butrymowicz

The isothermal section of the Ta-Ti-Zr-0 system at 1500°C was investigated using X-ray diffraction and rrzetallographic techniques. Up to 71.4 at, pct 0 the system contains nine four -phase regions. Zsopleths at 10, 20, 30, 40, 50, and 60 at. pct 0 were constructed. The purpose of this investigation was to determine the general shape of the quaternary equilibrium phase diagram of tantalum, titanium, zirconium, and oxygen at 1500°C. The system was truncated at 66.7 at. pct 0 on the Ti-0 and Zr-0 binaries and at 71.4 at. pct 0 on the Ta-0 binary. The Ti-Zr-0 system was investigated in this laboratory.' The binary systems of interest have been compiled and discussed by Hansen and Anderk, chmidt, Hayes, Roberson, and asche, and Hoch and athur.' EQUIPMENT The Same equipment as that for the study of the Nb(Cb)-Ti-Zr-0 system was used.' The X-ray dif- fraction patterns were analyzed with the help of the ASTM card set7 and NBS circulars.' MATERIALS The tantalum powder (99 pct pure), the titanium powder (99.6 pct pure), the tantalum pentoxide, and the zirconium dioxide used in this study were purchased from the Fairmont Chemical Co., Newark, N.J. The zirconium powder (99.4 pct pure) was obtained from the Charles Hardy Co., Inc., New York. Reagent-grade titanium dioxide was purchased from the Matheson Co., Inc., Norwood, Ohio. The oxides were dried in air at 700°C for 24 hr before use. Though the materials used were not "hyper-pure", the impurities present do not affect the results (lattice parameters, phase boundaries), within the experimental accuracy. PROCEDURE The samples were heated by induction in a vacuum furnace, and examined metallographically and by X-ray diffraction at room temperature. The procedure was the same as that in the Nb(Cb)-Ti-Zr-O work,' EXPERIMENTAL RESULTS AND DISCUSSION OF DATA A four-component system can be represented by a tetrahedron at a single temperature and pressure

Jan 1, 1964

By Nelson W. Taylor

With the extensive deposits of potash minerals which have been discovered in the southwestern states, and their rapid development, a permanent American supply of potassium compounds is now assured. The 325-year history of the potash industry in this country has been told by H. I. Smith1, of the U.S. Geological Survey, and the more recent activities of the Survey and of American potash companies were described last year by the same author2. In fact, it may be stated that so great is the productive capacity that two mines in New Mexico and one in California are able to supply more than half a million tons of crude and refined salts over and above that produced for agricultural purposes. The era of scarcity has given way to an era of superabundance. This situatiori makes it desirable for the potash producer to look for other applications for his product, and it is with this in mind that the writer presents some information pertaining to present and possible future uses for potassium compounds in the ceramic industry. Ceramic Products Ceramic products are essentially solid materials containing one or more oxides such as SiO2, Al2O3, CaO, MgO, FeO, K2O, Na2O, TiO2, which are the oxides of greatest abundance in the earth's crust. The typical ceramic process is that of firing or burning the batch, and the product may be glassy, crystalline or mixed. In the glassy or vitreous group come glass, porcelain enamel and glazes; in the crystalline group, refractory materials such as silica brick, or chromite or magnesia; and in the mixed group, porcelain, chinaware, stoneware, tile, brick, etc., which contain both a vitreous and a crystalline phase, in variable proportions. The ceramic industry of the United States is a billion dollar industry, and is important not only because of its magnitude but also because of the key position occupied by certain ceramic products in the whole manufacturing structure. From the standpoint of use of potash, the field of refractories is of no great interest, since K2O lowers the melting point of a refractory oxide and

Jan 1, 1938

The passing of Benjamin Bowden Lawrence in January, 1921, was a distinct loss to the engineering profession. Mr. Lawrence had a genius for reviving abandoned mines and developing them into substantial producers. A notable example of his work in this line was the Dives-Pelican near Georgetown, Colo. While on an exploring expedition in 1888, he examined this old mine and was convinced that bonanza ore still existed there. He located the owners of the property, and induced them to place sufficient capital at his disposal to enable him to re-open and explore this mine. So confident was he of the outcome that he undertook this work on a profit-sharing basis without salary. Within eighteen months the old Dives-Pelican was operating profitably, and for the following ten years it paid very substantial dividends. The late Theodore N. Vail was one of the owners of this old mine, and many years later, at a dinner given to Mr. Lawrence by the Alumni of Columbia University, Mr. Vail told the story of the resuscitation of the Dives-Pelican by Mr. Lawrence, and declared that the dividends he himself had received provided a large part of the funds that made possible the realization of his dream of establishing the long-distance telephone in this country. The E1 Cobre mines at Santiago de Cuba also owed their renewed life to Mr. Lawrence. Under his management, these mines produced and shipped several million pounds of copper per year. He was for several years consulting engineer for the Kerr Lake and other silver mines in the Cobalt region; the Kerr Lake became famous as a silver producer. Mr. Lawrence spent more than twenty years of his life in the mining camps of the West. He was but twenty-one years of age, and only a few months out of college, when he was appointed manager of the great Chautauqua Lode (a silver mine) located on Glacier Mountain near Montezuma, Colo. Here, isolated in the mountains for several months each year by ice and snow, he worked for five years to make these mines Pay. He possessed unusual breadth of vision and human understanding; he had ''personality plus," and when he opened an office in New York City as consulting engineer he quickly rose to an enviable position in his profession. Young engineers worked with enthusiasm under his guidance. He carefully selected his men, discussed fully with them the plans and policies to be pursued, then left them free to accomplish results in their own way. This attitude developed individuality and resourceful-

Jan 1, 1922

By Fred T. Greene

Most of the recent discussion of the mineral land law published in the Transactions is in the abstract—an exception being Mr. Goodale's paper, The Apex Law in the Drumlummon Controversyll which illustrates in concrete instances many of the practical disadvantages of what Dr. Raymond has called "The Law of the Apex." The present paper, it is hoped, may serve a similar purpose, emphasizing the necessity for a change in our mining laws, and bringing home to mining engineers some of the defects and dangers of our present code. There are many storm centers of "apex litigation" in the Rocky Mountains; and not the 1east. of them is the Wardner camp, where such litigation has been almost continuous since 1892, and the end is not yet. In their decisions, the courts have accepted the claims of the litigants that the "Wardner vein" is a broad zone varying from 250 to 500 ft. in width at the surface. This is the simplest theory which could have been advanced, and probably decreased, rather than augmented, the number of contests; in fact, every one of the claim owners seemed to feel that the greatest advantage would accrue to him if this theory were adhered to. The dominant structural feature of the Wardner vein is a persistent fault, striking N. 40' W., dipping about 40" to the southwest and called the "Wardner foot wall." Fig. 1 is a composite of two adjacent cross-sections of the vein and is a fair representation of the relative size and shape of the orebodies and their relation to the "Wardner foot wall." The country rock is a comparatively thin-bedded sericitic quartzite which has an average strike of N. 80" W. and dips at high angles to the north and south. The movement on the Wardner foot wall is apparently normal, and there has been more or less brecciation on either side of it; but as the moving mass was that above the foot wall, the brecciation has been more complete on that side, and has extended farther from the plane of movement. Many minor faults, generally of insignificant extent, resulted from the movement along the Wardner foot wall. Most of these were

Jan 1, 1916

By Strathmore R. B. Cooke, Emert W. Lindroos, Norman F. Schulz

DURING the course of an investigation of the effects of various starch products on hematite and quartz in regard to their separation by' flotation, it was found that whereas most starches flocculated suspensions of hematite in water, they did not flocculate similar suspensions of quartz. However, a derivative of whole corn starch containing approximately one tenth aminoethyl group (--CH2CH2NH2) per glucose unit proved to be an exception. This aminoethyl starch was a very good flocculant for both hematite and quartz, and also possessed the property of depressing both minerals in cationic flotation tests. In view of the widespread use of starch as a flocculating agent of solids in tailing water, pulps, and for coal slimes, ore and various other purposes in sulphide and nonsulphide flotation, attention is called to the effective surface activity of aminoethyl starch in flocculating suspensions of the two minerals investigated. Test Materials The starch products employed included Globe Pearl starch No. 144 and fresh aminoethyl starch, both supplied by the Corn Products Refining Co. Dr. A. L. Elder[4] has kindly furnished a description The minerals used in the various tests are listed in Table I. Their specific surfaces were determined by the air permeability method, which gave results reproducible to within plus or minus 3 pct. Surface areas obtained by krypton adsorption were greater than the air permeability values by a factor of 2.0 for quartz and 62.4 for hematite. Starch Adsorption on Mineral Surfaces Starch adsorption data were obtained by agitating for 1 hr measured volumes of neutral starch solutions of known concentrations with weighed quantities of finely divided mineral of measured specific surface. The mineral then was separated from the pulp liquor by centrifugation and the residual starch content determined by chemical analysis. The analytical procedure consisted of oxidizing the starch with an excess of dichromate in acid medium at elevated temperature and titrating the excess dichromate by the ferrous ammonium sulphate-potassium permanganate method. Analytical results were reproducible to within less than 1 pct. Adsorption data obtained in unbuffered solutions near the neutral point are plotted in Fig. 1. The adsorption on either mineral was far greater for the aminoethyl starch than for the Pearl starch. Flocculation The degree of flocculation was determined for a given pulp by measuring the time required for the supernatant liquid to reach a certain degree of clarity. This was accomplished by passing a standard light beam through the pulp, contained in a glass settling tube, and measuring the time required after agitation ceased for the intensity of the transmitted beam to reach a predetermined value. Starch reagent was added to each pulp in small uniform increments, and the settling time was determined after each such addition. Increase in pulp liquor volume due to the added starch reagent was ignored in these tests. Pulps were maintained at or near neutrality.

Jan 1, 1952

By I. Fatt

Laboratory relative permeability data on reservoir rock are obtained on samples which are not subjected to overburden pressure during the permeability measurements. These data are then used for calculating the performance characteristics of reservoirs in which the rock is under the pressure of the overburden. Recent observations have shown that the permeability and porosity of reservoir sandstones are decreased by application of overburden pressure. These observations led us to a study of the effect of overburden pressure on the relative permeability characteristics of sandstones. A previous note from this laboratory1 showed that overburden pressure, simulated by applying hydraulic pressure to the outside of a plastic mounted core. caused a reduction in permeability of the core by as much as 50 per cent at 10,000 psig. In a multiphase fluid flow system, the relative permeability at a given saturation will change if the permeability or the effective permeability changes but not if both permeability and effective permeability change by the same ratio. The tests described in this note were made to determine the effect of overburden pressure on permeability and effective gas permeability in the gas-oil system. The gas-oil system was chosen because the available equipment was best suited for studying this system. The resultant data can be applied to other systems of interest because the gas permeability in the gas-oil system is the permeability of the nonwetting phase and, as such, is equivalent to the gas permeability in the gas-oil-water system and to the oil permeability in the oil-water system. EXPERIMENTAL METHOD Cylindrical test plugs, one in. in diameter and one in. long, were cut from sandstone core samples from three different reservoirs. After extraction in toluene, the plugs were mounted in Lucite by conventional core mounting methods.3 The core properties are given in the legend in Fig. 1. The mounted cores were machined to fit the apparatus shown in Fig 4. Air permeabilities as a function of overburden pressure were measured by connecting lines (1) and (2) to a conventional air permeameter. To measure porosity changes as a function of overburden pressure, the lines leading to (1) and (2) and the core were saturated with kerosene; line (1) was capped and a small bore precision calibrated pipet was connected to (2). Changes in pore volume of the core as overburden pressure was applied were noted by reading the amount of kerosene produced into the pipet. To correct for the change in volume of the lines inside the hydraulic cell as a function of pressure, a pressure-vs-volume run was made with a solid Lucite cylinder substituted for the core. The change in volume of the lines was about 10 per cent of the change in pore volume of the core. No correction was needed for the permeability measurements because there was no measurable pressure drop in the lines at the maximum overburden pressure. Relative gas permeabilities were measured by the stationary liquid method described by Osoba, et al.' Gas saturations were obtained by allowing the kerosene from a kerosene saturated core to evaporate out. This procedure was followed

Jan 1, 1953

By Charles H. Thurman

THE data given herein were first included in a paper read before San Francisco Section, A.I.M.E., in October 1940, and are applicable to conditions existing until the gold-dredging industry was temporarily suspended by Order L-208 of the War Production Board in the fall of 1942. There is no doubt that gold dredging will be resumed at some future time, and on a scale equivalent to that of the recent past, but the cost data given herein will be affected to some extent by conditions existing at that time, and by labor rates and prices for materials then prevailing. DRAGLINE VS. BUCKET-LINE Dragline dredges should not be considered for mining large areas of low-grade placer gravel. In such deposits a dragline operator with a 5-cu. yd. dragline would be doing well to maintain an operating cost of 6¢ per cu. yd., while a bucket-line dredge with buckets no smaller than 7 cu. ft. each could be operated for less than 4¢ per cu. yd. By operating costs, I mean only field charges such as direct operating and overhead, which includes pay roll, power or fuel, repairs and maintenance, insurance, land clearing and general expenses, but not including such items as prospecting, depletion, depreciation of equipment, State Franchise Tax, or Federal Income Tax. It is not to be inferred that a dragline dredge cannot make a profit in small low-grade deposits, where the extent of a given property is too small to justify the use of the more costly bucket-line dredge. Consider small deposits of 10¢ gravel. It is obvious that a deposit of 5,000,000 cu. yd. of such gravel could not be mined profitably with a new, 7-cu. ft. bucket-line dredge, costing upward of $250,000, and with operation costs at 4¢ per cu. yd., paying for land or royalties out of earnings; nor could a new combination 5-cu. yd. dragline and washing plant, worth upward of $125,000 and working at 6¢ per cu. yd., make a profit. These comparisons are made because the hourly capacity of both types of dredges is nearly the same. The bucket-line dredge averages 93 per cent operating time in 24 hr., as against about 80 per cent or less for the dragline dredge. These percentages of operating time are important factors in making a comparison of this kind. The bucket-line dredge has greater efficiency in cleaning soft bedrock, usually characteristic of dredging deposits, and a 7-cu. ft. bucket-line dredge can be efficient to a total digging depth of 80 ft. (65 ft. below water, 15 ft. above). A 5-cu. yd. dragline dredge is limited to about 30 ft. of efficient digging depth, 5 ft. of which could be above water. In small areas of gravel not over 30 ft. deep, a 5-cu. yd. dragline dredge could make a profit where a bucket-line dredge could not do so. As an example: compare the dredging of 3,000,000 cu. yd. of 10¢ gravel 28 ft. deep with bucket line, costing 4¢ per cu. yd., and with a 5-cu. yd. dragline dredge operating at 6¢ per cu. yd. Because of small yardage, new equipment is not warranted, therefore we can assume that the dredges of both types are used equipment, fully depreciated. Dismantling, mov-

Jan 1, 1945

By F. V. Lenel, G. S. Ansell, M. J. Salkind

An experiment is described in which the growth of interparticle necks in an array of loose spherical silver powder at temperatures near 300°C was determined by measuring changes in the electrical resistance of the array. The activation energy for neck growth of contacts was derived by abruptly changing temperature and noting the change in the rate of neck growth. Since the experiments were run under an external load, the changes in activation energy with stress could he determined. The activation energy was found to decrease rapidly with increasing stress. It is concluded that the material transport in the experiments is one of plastic flow by dislocation motion. The variation of activation energy with stress is typical for cross slip of dislocations, an important material transport mechanism in the temperature range investigated. THE process in which powder compacts or aggregates of loose powder are held at an elevated temperature under an external load is called hot pressing or sintering under pressure by powder metallurgists. In this investigation the early stages of this process as applied to loose spherical silver- powder aggregates were studied. The powder particles were approximately 100µ in diameter and the temperature was near 300°C, i.e., below one half of the melting point of silver in degrees Kelvin, where volume diffusion is not expected to contribute to sintering. In the process, the contact or neck areas between powder particles grow. Since this involves plastic deformation of the particles under a constant external load (even though not under constant stress) it would be termed creep by mechanical metallurgists. On the other hand, the growth in neck area observed in compacts or loose-powder aggregates held at elevated temperature without the application of an external load is termed sintering by powder metallurgists. During sintering the major driving force is the stress due to surface tension. However, even when no load is placed on the compact or powder aggregate, an external stress, i.e., gravity, plays an important role in sintering in addition to those stresses arising from surface tension, as was shown in two previous investigations.'" It is therefore postulated that no sharp dividing line can be drawn between the phenomena of "creep" and "sintering". Different material transport mechanisms may be involved in either of these phenomena, but they will depend upon the temperature and the level of stress, but not necessarily upon the nature of the driving force: surface tension or external load. At the low temperatures of this investigation, an external stress much higher than the stress due to surface tension is necessary to obtain measurable rates of neck growth. In order to avoid misunderstanding this phenomenon will be called "creep". The rate of growth in contact area in the loose silver-powder aggregates was determined by meas-

Jan 1, 1965

By Russell Paul

THE Wisconsin zinc district, also known as the Upper Mississippi lead and zinc district, is an area of about 2500 sq. mi. in the southwestern portion of Wisconsin and adjacent parts of Illinois and Iowa. It includes Iowa, Grant and Lafayette counties in Wisconsin, Jo Davies County in Illinois, and an irregular strip of Clayton and Dubuque counties in Iowa, parallel to the Mississippi River. During periods of high metal prices mining has been quite active in this district, but recently the lower metal prices have caused many companies to suspend, so that at the present time there are only a small number of mines operating. The short life of these mines and the low mineral content of the zinc deposits limit the investment in development and equipment, and necessitates the operation of this equipment at maximum running time and maximum capacity. The tonnage of rock handled (locally termed dirt) is large in comparison with the tonnage of concentrate produced. Moreover, the zinc content of the concentrate is low, varying from 25 to 40 per cent zinc, and the value per ton is correspondingly low. The life of the mines varies greatly. An exception-ally good deposit may produce 2,000,000 tons of rock during a period of ten years, market value permitting, from which will be obtained 100,000 to 150,000 tons of concentrate. One property which might be con-sidered as fulfilling the requirements of a profitable operation was developed and equipped in 1925, oper-ated continuously for a period of two and a half years, produced 484,292 tons of rock, from which was obtained 37,659 tons of zinc concentrate, 34.4 per cent Zn, and 1155 tons of lead concentrate, 67 per cent Pb. During the war period prices of ore permitted the mining of lower grade ores than has been possible in the past few years. The maintaining of a higher grade mill-feed has resulted in reducing the size of stopes formerly carried in the old mines and confining the workings within narrower limits.

Jan 7, 1928

By H. Kurushima, S. Tsunoda

An investigation of the hydrometallurgy of Cu-Zn concentrates by The Dowa Mining Co. of Japan is described and a detailed flowsheet of the Kosaka hydro-metallurgical plant is given. Sufficient operating experience has shown that the Dorrco FluoSolids system has proven successful for recovery of both zinc and copper by roasting in a fluidized bed. At present, 2400 metric tons of concentrates per month are being treated and recoveries of 93 pct Cu and 65 pct Zn are being effected. A SURVEY of the Japanese chemical industry in 1949 revealed, among other things, that sulphur-bearing blast furnace gas from the Kosaka smelter of The Dowa Mining Co. Ltd., Kosaka, Japan, was being exhausted to the atmosphere as waste. In addition, it was costing that company an average of ten million yen ($28,000) annually for damages to the surrounding property caused by the sulphur dioxide in the gas. It was recommended by this survey that the gas be utilized for the production of sulphuric acid by the contact process. Mr. Kurushima visited the United States in May 1950 to investigate the engineering, construction, and operation of a contact acid plant. Any acid produced at Kosaka would necessarily have to be 98 pct H,SO, to prevent corrosion in railroad tank cars transporting it to the point of use. However, the production of 98 pct acid requires constant volume and SO, content of the gas. As the converter gas at Kosaka fluctuates in both volume and quality, it was decided to evaluate the smelting process with relation to other methods of recovery. This evaluation revealed a relatively new type of roaster, the Dorrco FluoSolids reactor, which was reported to be capable of roasting the copper sulphide concentrate in an excess of air with the production of an SO1 gas strong enough for acid production and a water-soluble copper sulphate calcine. The copper sulphate then could be leached from the roasted ore and electrolytic copper recovered from the leach solution in much the same manner as practiced by the Chile Exploration CO. for treating naturally occuring copper sulphate ores. Use of a reactor of this type would eliminate the need for a blast furnace and converter and, in addition, would effect savings in labor and fuel. The Kosaka ore is a microscopically fine mixture of copper, zinc, and lead sulphides. The lead and a small amount of the barite present can be separated by flotation, but any separation of copper and zinc proved extremely difficult. In blast furnace operation at Kosaka, zinc had been slagged off until a stockpile of about 12,000,000 tons containing 5 pct Zn had been accumulated. Mr. Kurushima felt that if any of the zinc in the concentrate was sulphat-ized and leached with the copper, it also could be recovered electrolytically. The Dorr Co., sponsors of fluidization technique in the metallurgical field, suggested that sulphate roasting be tested out on a laboratory scale and that, if successful, a commercial Dorrco FluoSolids system be constructed. They indicated that the results from such laboratory tests could be transposed to a commercial scale without pilot planting the roasting operation. It was therefore decided to send samples of flotation concentrate to the West-port Mill, laboratories of The Dorr Co., for testing. The objective of Mr. Kurushima's visit to the United States thus had changed from investigation of sulphuric acid plants to a fundamental examination of the hydrometallurgy of copper and zinc. Testing Program In February 1951, Mr. Tsunoda went to the United States to witness the application of the FluoSolids system to sulphate roasting at The Dorr

Jan 1, 1956

By A. U. Seybolt

The solubility of oxygen in a iron has been determined in the range between 700° and 900°C. The solubility is a function of temperature and varies from about 0.008 pct oxygen at 700°C to atureandabout 0.03 pct at 900°C. The heat of solution is approximately +15,500 cal per mol. AS pointed out in a recent paper by Kitchener et al.,1 there has been a lack of agreement among many investigators even as to the order of magnitude of the solid solubility of oxygen in the various forms of iron. This lack of agreement is attributable in large part to the difficulties in the determination of a small oxygen solubility; but because the problem has remained so long unsettled, it also indicates a lack of interest which is rather surprising when the demonstrated importance of small amounts of soluble nonmetallic impurities in iron is considered. The work of Kitchener et al. apparently leaves the solubility of oxygen in iron in a satisfactory state, but no attempt was made to investigate the solubility in a iron. The solubility of oxygen in a iron is actually of greater interest, since it is in this form that iron and mild steels are employed ordinarily. That the effect of oxygen in iron is of more than theoretical interest has been well established by Fast,' and more recently by Rees and Hopkins," who demonstrated that oxygen in the range between 0.0008 and 0.27 wt pct has a pronounced effect upon the mechanical properties. Previous Work and Methods Used To report in detail the literature relating to the solubility of oxygen in a iron would require an inordinate amount of space. For those interested in reviewing this work, a bibliography4-13 of the more significant papers is appended. In general, two methods of studying this problem have been used. One is the gas-metal equilibrium method where the H2O-H2-Fe or the CO2-CO-Fe equilibria have been used. The other is the more direct approach of the oxidation of thin strips of pure iron by packing in mill scale or by air or gaseous oxygen at some desired temperature. In this method oxygen is allowed to oxidize the surface and then to diffuse inward until saturation is obtained. In the gas-metal equilibrium method the oxygen dissolved in solid iron at a given temperature is proportional to the ratio of the water vapor-hydrogen pressures or the CO2-CO pressures over the sample for small ratio values. If the ratio becomes higher than a critical value, then an oxide phase makes its appearance (the solution becomes supersaturated). In principle, it is possible to use a series of H2O/H2 or CO2/CO ratios and to find by analysis the corresponding amounts of oxygen in solid solution at constant temperature. At the point where a very small increase in the gas ratio (increase in oxidizing powder) produces a large increase in oxygen content, the solid solubility limit is reached. Alternately, if the critical ratio is known, it is possible to use the procedure of Kitchener et al.1 and to use a ratio which is near but below the critical one. The solubility corresponding to this lower ratio will not be the saturation solubility at the temperature employed, but the saturation solubility can be calculated by multiplying the measured solubility by the critical ratio over the ratio used. However, in the case where oxygen gas is the oxidizing medium, the saturation solubility is not a function of pressure, providing the pressure exceeds the dissociation pressure of FeO in equilibrium with iron. This is 1.2x10-16 mm at 800 °C, according to Dushman." As pointed out by Darken17 in discussing the FeO phase diagram, most of the possible errors tend to yield high values of oxygen solubility. For example, one circumstance which evidently caused the reporting of many high values was the use of finely divided or powdered iron in the gas equilibrium method. Because of the large surface area of such a sample, and the likelihood of some surface contamination if only by exposure to air, the results tended to be high. The direct oxidation method which was used in this work has the advantage in that it is simple and direct, but it suffers from one disadvantage: equilibrium can only be approached from the low oxygen side. The important factors to be kept under control are the following: 1—use of high purity iron to avoid internal oxidation (oxidation of readily

Jan 1, 1955