Search Documents

By R. E. Tate, L. J. Herman

We have had occasion to produce wire of Np-237 in small diameters for use in some chemical experiments. Since the mechanical metallurgy of neptunium has not been investigated extensively, it seems desirable to report our successful extrusion technique. Because of the neptunium activity and its attendant health hazard the experimental work was done in glove boxes and related equipment also used for Pu-239. At room temperature a phase neptunium' is a hard (Dph -355) orthorhombic metal of high density (p = 20.45 g per cu cm). a neptunium transforms2 to tetragonal ß neptunium at about 280°C and this in turn transforms to bcc y neptunium at about 577°C. The y phase melts at about 637°C. A temperature of 340° to 345°C was selected for the extrusion, this temperature being a compromise be- tween a possible advantage of working with the presumably more plastic cubic y phase above 577°C and the risk of having the neptunium react with the alloy steel die to form the low-melting Fe-Np eutectic. A 0.75-in.-long, 0.26-in.-diameter ingot of good-purity* Np-237 was extruded by the direct *C = 230 ppm, Pu = 200 ppm, thirty-five metallic elements below limit of detection by spectrographic methods. process through flat-face orifices to form several sizes of wire ranging from 0.010 to 0.030 in. in diameter. Molybdenum disulfide was used as the die lubricant. The extrusion was done in a vacuum of about 10-4 torr to reduce reaction of the neptunium with atmospheric gases. British workers3 at Harwell have extruded neptunium under similar conditions. The force required to extrude 0.010-in.-diameter wire at the rate of 4 in. per min was 6000 lb, as measured with an electrical load cell. Wire 0.020 in. in diameter was extruded with a force of 4700 lb at a rate of 2 in. per min, and wire 0.030 in. in diameter was extruded with a force of 4000 lb at a rate of 1.3 in. per min. An extrusion constant, c, can be computed from the measured forces, P, for the equation4 P = c log-A/a where A/a is the extrusion ratio or the ratio of the cross-sectional areas of the container and the

Jan 1, 1965

By K. C. Mills, E. T. Turkdogan

A number of investigators1 6 have noted the presence of a liquid miscibility gap in the Fe-Sn binary system. However, the first attempt to measure the

Jan 1, 1964

By F. D. Wright, H. D. Fara

The solution to the plastic and elastic stresses around a circular shaft in a hydrostatic stress field that has appeared in two editions of a widely used book on rock mechanics1 is in error. Although this is a relatively minor matter, the correct solution was not found by a literature survey, so it appears worthwhile to present it. For a homogeneous, isotropic, rigid plastic-elastic body in plane strain which obeys Tresca's yield criterion the following equations must be satisfied:'," In the plastic zone,

Jan 1, 1963

By Philip B. Bucky

CONTENTS [PACEPACE r. What Is a Rock Burst?2 4. How Can Rock Bursts Be Predicted? . 35 Jack Spalding2Jack Spalding35 A. F. Robertson 2, 5A. F. Robertson35 W. R. Crane 2A. B. Yates and P. J. Shenon. . . . 35 G. S. Rice 2W. R. Crane 35 P. J. Shenon 2G. S. Rice 35 L. C. Graton 2B. F. Tillson 36 2. What Are the Causes of Rock Bursts? 6 5. How Can Rock Bursts Be Controlled?. 36 Jack Spalding6Jack Spalding36 A. B. Yates and P. J. Shenon . 7, 12, 29A. F. Robertson 36 A. F. Robertson 12, 28W. R. Crane37 W. R. Crane 15A. B. Yates and P. J. Shenon. . . . 37 G. S. Rice 15Oscar Weiss38 Oscar Weiss15G. S. Rice37, 42 P. B. Bucky21R. D. Hoffman42, 43 P. H. Bird 21, 26, 28R. D. Hall 42 M. K. Hubbert26R. H. Cromwell42 G. Wheeler 26. J. Shenon 42 B. F. Tillson26, 28P. B. Bucky42, 44 T. T. Read 27B. F. Tillson 42, 44 A. B. Yates 43, 44 3. How Can Rock Bursts Be Prevented? . 30P. H. Bird 43 Jack Spalding. . . . • . • • • • . 306. General Discussion . A. B. Yates and P. J. Shenon. . . . 31Jack Spalding44 A. F. Robertson32R. D. Parker49 W. R. Crane 35C. Baring Horwood 51 G. S. Rice 35P. B. Bucky 52] FOREWORD THIS symposium brings together points of view, experiences and ideas on rock bursts from a goodly portion of the globe. Some conceptions, particularly those regarding the necessity of depth, have been fairly well shattered, as we find that they are present in the water tunnels of New York, on the surface at marble quarries in Vermont, and in the coal mines of the United States, as well as in the deep mines of the South African and Kolar gold fields, and in the nickel, copper and gold mines of Canada. Their occurrence under such a variety of conditions is, therefore, a challenge,

Jan 1, 1942

By AIME AIME

PLANS are now well advanced for the joint meeting of the Institute and over a dozen other engineering societies in Chicago during the week beginning June 26: Engineers' Week at A Century of Progress. All engineers planning to visit the Fair will find it to their advantage to be present at this time so far as the Chicago attractions are concerned, and Eastern members will also have the advantage of special transportation arrangements on June 24 and 25. The tentative program is given at the bottom of the next page. Monday morning, June 26, will be reserved for registration of members and guests and the Woman's Auxiliary at the Stevens Hotel, where special rooms will be provided. A luncheon will also be served there, and in the afternoon, a technical session on nonmetallics. Instead of having the big family dinner that evening at the Stevens, as at first proposed, the local committee has planned to have it at the Fair Grounds, where special facilities have been arranged. A meeting of the Board of Directors and a few invited guests will precede the dinner. All members and guests are likely to be interested in visiting the Museum of Science and Industry, so that will be the sole event on the program for Tuesday morning, June 27. The big attraction there at present is the model coal mine, the first operative coal mine ever built for exhibit purposes. It is based on the Deutsches Museum mine at Munich, but goes far beyond that in realism, and takes the visitor on an extended tour underground. It shows him in half an hour more types of modern mining machinery and coal geology than he would be likely to see in a week's underground study in the coal fields. The Institute members will be the first group to go through this mine.

Jan 1, 1933

By A. S. Argon, G. East

From their study of the anisotropy of grain boundary mobility in aluminum, the authors conclude that tilt boundaries have a higher mobility than twist boundaries because the atomic misfit at the pure-twist boundary is relatively small compared to the misfit at a tilt boundary for a given amount of misorientation. If this is true, then one would expect a twist boundary to have a lower grain boundary energy than the corresponding tilt boundary. Fig. 6, taken from the work of Gjostein and Rhines,10 shows that this is indeed the case for [001]-cu tilt and twist boundaries in the high-angle region, thus lending support to the authors' conclusion.

Jan 1, 1968

Jan 1, 1967

By John C. Smock

The rich deposits of magnetic iron-ore in the Highlands of northern New Jersey attracted the attention of iron-workers at the time of the earliest settlements in that region. The outcrops of the oreshoots at the Dickerson mine, at Mount Hope, and at Hibernia, in Morris county, and at Ringwood, in Passaic count,y, which were doubtless such as would lead to discovery, location and development of nearly all the large iron-mines in that part of the State, appear to have had their beginnings where the ore cropped out on the surface or where it was scarcely concealed by a thin mantle of earth. In the early history of New Jersey iron-mining, the careful explorations and surveys made by the agents of the famous London Com-

Jan 1, 1892

By Fred D. Wright, Philip B. Bucky

FOREWORD By E. D. Gardner[$] THE present known petroleum reserves are limited, and unless important new fields are discovered the Nation will be dependent, in the not too distant future, upon imports or upon synthetic liquid fuels to supplement domestic petroleum supplies. As a national defense measure, it would appear desirable to develop a substitute source of liquid fuels within the borders of the country if new discoveries of petroleum should prove disappointing. Congress undoubtedly had this in mind when it passed the Synthetic Liquid Fuels Act (78th Congress, approved April 5, 1944). The act directed the Bureau of Mines to construct and operate demonstration plants for producing synthetic liquid fuels from coal and oil shale, and from forestry and agricultural products. As a part of this program, the Bureau of Mines has built a demonstration plant at Anvil Points, near Rifle, Colo., for retorting the oil shale, and has developed a mine to supply the plant with oil shale. At the beginning of mining operations, the physical qualities of the oil shale, which would have a bearing upon the selection of mining methods and practices for exploiting the deposits, were largely unknown. A comprehensive mining-research program has been set up to determine the best methods and practices to follow to obtain the lowest overall practicable mining cost for producing the oil shale on a large scale. Unusually low mining costs will be necessary for shale oil to be produced commercially. Consideration now is being given to exploiting a series of flat-lying beds 70 ft thick by a room-and-pillar method of three benches with the advance heading at the top. This report is one of a series giving the results obtained in research on mining problems. INTRODUCTION The structure and physical qualities of the oil shale indicate that the 70-ft interval of the oil-shale measure can be safely mined in open stopes; studies indicate that this method would be the most economical one to use.1 As labor will be a major item of expense, the largest equipment that could be operated efficiently in the workings would be required to obtain the lowest practicable mining cost. It was therefore desirable to know the maximum safe span of unsupported rooms and the size of pillars necessary to support the overburden. This paper describes the work done at the Columbia School of Mines Barodynamic Laboratory in determining the maximum safe unsupported roof spans and the minimum safe pillar dimensions for the oil-shale mine at Rifle, Colo.

Jan 1, 1947

By J. P. Carson

The works of the Tula Iron Company are in the Republic of Mexico, State of Jalisco, twenty-eight leagues southwest of Guadalajara, ten leagues northwest of the town of Sayula, through which passes the projected line of the Mexican National Railroad. Its geographical position would be about: latitude, 20' 10' N., longitude, 40 35' w. of Mexico City. The surrounding country is a rolling plateau, 6000 feet above the sea, enjoying the most magnificent climate in the world, the average temperature being about '70'. The works were commenced in 1850 by a company with very small capital, having not the least idea of the undertaking. They soon fell into the hands of the money-lenders, and after changing

Jan 1, 1879

By Charles De Witt

The ore treated at the reduction plant (called Yangdei) of the Chiksan -Mining Co., Korea, is brought from four of the company mines, and from the small tribute mines. The largest shipments conic from Sajunkohl mule, situated about a mile and a half from the mill (Fig. 1). The ore is quartz of medium hardness. The overage assay value in gold is $6.95 per ton. At the mine the ore is put into bin,, and is Mien trammed over an 8 per cent. grade to the tipple bins above the mill, where the ore is drawn through the hull holes as desired. The capacity of the tipple bins is about 3,500 tons. On, from Moonsukohl, Chung Tarrie, Yang Chun, and the tribute mines is brought in by bulls and bull wagons. The bulls carry from 350 to 800 lb.; the average wagon load is about 1,200 lb. (Fig. 2). One shovelful of ore out of every ten is taken as a sample. Considerable ore

Jan 5, 1915

By R. L. Fullman, J. W. Cahn

A method is derived for obtaining the distribution of sphere diameters and plate thicknesses (or pearlite spacings) from size distribution functions obtained along randomly oriented lines. The method described offers several advantages over existing methods. IT is often of interest to measure not only the average particle size but also the distribution in sizes of particles dispersed in an opaque material, such as an alloy. Particles of a single size will exhibit a range of apparent sizes on the plane of polish. If the sample contains a distribution of particle sizes, the distribution of observed sizes on the plane of polish is related to the distribution of actual particle sizes by an integral equation, For example, a distribution of sphere sizes, N(r),

Jan 1, 1957

By E. A. Swedenborg

The unit agreement for the Wertz Dome field, Wyoming, was approved by the Acting Secretary of the United States Department of the Interior on November 4, 1937, effective on December 1, 1937. The stated objectives of the agreement are to conserve and put to beneficial use all oil and gas produced; to make possible a uniform withdrawal of oil and gas in order to maintain equalized reservoir pressures; to provide for an orderly determination of the structural features of the productive horizons; and to permit the injection of gas for pressure maintenance. The purpose of this paper is to show by a discussion of the problems involved and the engineering practices employed by the unit operator, how well the objectives of the unit agreement have been accomplished in the development and production of oil and gas from the field. HISTORY AND DEVELOPMENT The Wertz Dome oil and gas field is located 88 miles southwest of Casper and 38 miles north and westerly from Rawlins, Wyoming. It is served by a state secondary oiled road connecting with U. S. Highway No. 220 at Lamont, a distance of 3 miles from the field. It has been a producing field for 27 years, first as an important producer of gas and more recently of oil. The Producers and Refiners Corp. completed Well No. 1, NE1/4SW1/4 sec. 7, T. 26 N., R. 89 W., the first productive well in the field, in September. 1921, in the Muddy sandstone of Upper Cretaceous age, at a depth of 3435 feet for an initial production of 42,000,000 cu. ft. of gas per day. In 1922 pipe lines were laid to Casper, Wyoming, for supplying fuel to the Standard of Indiana refinery, 'the adjoining town of Mills. and the Producers and Refiners Corp. pump station No. 6 in Mills; and to Parco (now Sinclair), Wyoming, for supplying that refinery with fuel. The gasoline content of the gas was extracted in an absorption plant located near the town of Mills. No compressors were used as the line pressure was sufficiently high to flow the gas through the absorbers. As high as 30,000,000 cu. ft. of gas per day were treated in the plant extracting 6000 gallons of gasoline. In September 1937, the pipe line was discontinued and the plant was dismantled at which time 61,000,000,000 cu. ft. of gas had been produced from the seven Muddy, Cloverly, and Sundance gas wells drilled in the field. Of this volume of gas 800,000,000 cu. ft. were produced from the Frontier formation, 34,200,000,000 cu. ft. from the Muddy sandstone, 24,000,000,000 cu. ft. from the Cloverly, locally called Dakota, and 2,000,000,000 cu. ft. from the Sundance formation. The pipe line was discontinued because of the near depletion of the gas reserves in Wertz and nearby fields, and hecause of the local field requirements demanding the retention of the remaining gas reserves. In December 1936, the Sinclair Wyoming Oil Co. completed Well No. 10, SE1/4NW1/4 sec. 7. T. 26 N., R. 89 W., at a depth of 5886 feet. as the first Tensleep sand producer with an intial of 1700 barrels of oil per day. The well was originally drilled only 14 feet into the sand and in August 1939 was deepened to a depth of 6161 feet, 289 feet in the sand, and the daily produe tion increased to 8350 barrels of oil. In February 1948 Well No. 22, SE1/4 SE1/4 sec. 1. T. 26 N., R. 90 W., was deepened from the Tensleep to the Basal Amsden sand and completed at a depth of 6635 feet for an intial of 600 barrels of oil per day in the Basal Amsden. In April 1948, Well No. 2. SW1/4 NE1/4 sec. 1, T. 26 N., R. 90 W.. was deepened from the Tensleep to the Madison limestone and was completed at a depth of 7193 feet for an intial of 1145 barrels of oil per day in the Madison. Well No. 26, SE1/4SE1/4 sec. 1, T. 26 N.. R. 90 W., was deepened from the Ten-sleep to the Cambrian and in October 1948 it was completed in the Cambrian for an intial of 277 barrels of oil per day. GEOLOGY AND PRODUCTIVE ACREAGE The surface is Steele shale of Upper Cretaceous age, covered in part by gravel beds. The topography of the field is that of a rolling hill with a steep draw or gulch along the northern edge of the field. The Steele shale lies conformably on the lower formations as

Jan 1, 1949

By E. A. Swedenborg

The unit agreement for the Wertz Dome field, Wyoming, was approved by the Acting Secretary of the United States Department of the Interior on November 4, 1937, effective on December 1, 1937. The stated objectives of the agreement are to conserve and put to beneficial use all oil and gas produced; to make possible a uniform withdrawal of oil and gas in order to maintain equalized reservoir pressures; to provide for an orderly determination of the structural features of the productive horizons; and to permit the injection of gas for pressure maintenance. The purpose of this paper is to show by a discussion of the problems involved and the engineering practices employed by the unit operator, how well the objectives of the unit agreement have been accomplished in the development and production of oil and gas from the field. HISTORY AND DEVELOPMENT The Wertz Dome oil and gas field is located 88 miles southwest of Casper and 38 miles north and westerly from Rawlins, Wyoming. It is served by a state secondary oiled road connecting with U. S. Highway No. 220 at Lamont, a distance of 3 miles from the field. It has been a producing field for 27 years, first as an important producer of gas and more recently of oil. The Producers and Refiners Corp. completed Well No. 1, NE1/4SW1/4 sec. 7, T. 26 N., R. 89 W., the first productive well in the field, in September. 1921, in the Muddy sandstone of Upper Cretaceous age, at a depth of 3435 feet for an initial production of 42,000,000 cu. ft. of gas per day. In 1922 pipe lines were laid to Casper, Wyoming, for supplying fuel to the Standard of Indiana refinery, 'the adjoining town of Mills. and the Producers and Refiners Corp. pump station No. 6 in Mills; and to Parco (now Sinclair), Wyoming, for supplying that refinery with fuel. The gasoline content of the gas was extracted in an absorption plant located near the town of Mills. No compressors were used as the line pressure was sufficiently high to flow the gas through the absorbers. As high as 30,000,000 cu. ft. of gas per day were treated in the plant extracting 6000 gallons of gasoline. In September 1937, the pipe line was discontinued and the plant was dismantled at which time 61,000,000,000 cu. ft. of gas had been produced from the seven Muddy, Cloverly, and Sundance gas wells drilled in the field. Of this volume of gas 800,000,000 cu. ft. were produced from the Frontier formation, 34,200,000,000 cu. ft. from the Muddy sandstone, 24,000,000,000 cu. ft. from the Cloverly, locally called Dakota, and 2,000,000,000 cu. ft. from the Sundance formation. The pipe line was discontinued because of the near depletion of the gas reserves in Wertz and nearby fields, and hecause of the local field requirements demanding the retention of the remaining gas reserves. In December 1936, the Sinclair Wyoming Oil Co. completed Well No. 10, SE1/4NW1/4 sec. 7. T. 26 N., R. 89 W., at a depth of 5886 feet. as the first Tensleep sand producer with an intial of 1700 barrels of oil per day. The well was originally drilled only 14 feet into the sand and in August 1939 was deepened to a depth of 6161 feet, 289 feet in the sand, and the daily produe tion increased to 8350 barrels of oil. In February 1948 Well No. 22, SE1/4 SE1/4 sec. 1. T. 26 N., R. 90 W., was deepened from the Tensleep to the Basal Amsden sand and completed at a depth of 6635 feet for an intial of 600 barrels of oil per day in the Basal Amsden. In April 1948, Well No. 2. SW1/4 NE1/4 sec. 1, T. 26 N., R. 90 W.. was deepened from the Tensleep to the Madison limestone and was completed at a depth of 7193 feet for an intial of 1145 barrels of oil per day in the Madison. Well No. 26, SE1/4SE1/4 sec. 1, T. 26 N.. R. 90 W., was deepened from the Ten-sleep to the Cambrian and in October 1948 it was completed in the Cambrian for an intial of 277 barrels of oil per day. GEOLOGY AND PRODUCTIVE ACREAGE The surface is Steele shale of Upper Cretaceous age, covered in part by gravel beds. The topography of the field is that of a rolling hill with a steep draw or gulch along the northern edge of the field. The Steele shale lies conformably on the lower formations as

Jan 1, 1949

By R. E. Radabaugh, J. M. Brown, J. S. Merchant

The Gilman district is on the northeast flank of the Sawatch Range in central Colorado. It has yielded a total of 10,000,000 tons of ore having a value of over $250,000,000. Paleozoic sediments intruded by a Tertiary quartz latite sill and unconformably overlying Precambrian intrusives and metasediments comprise the country rock of the area. The sediments strike northwesterly and dip 8° to 12° northeasterly. Structures in the Precambrian are related to the Homestake shear zone of the Colorado mineral belt. Only minor folding and faulting occur in the sediments. The principal ore bodies are massive sulfide replacement deposits in carbonate rocks. They consist of long, pipe-like mantos in the completely dolomitized Mississippian Leadville Limestone and funnel-shaped chimneys of copper- silver ore cutting across the Mississippian and Devonian strata. Mineralization is continuous from the chimneys into the mantos. The principal ore bodies are roughly in the shape of a four-tined fork which points up dip. Smaller manto deposits occur in the Cambrian Sawatch Quartzite, and fissure veins are present in the Precambrian rocks. The principal minerals in the mantos are marmatite and galena in a gangue of pyrite and manganosiderite. The chimneys consist of a central core of pyrite with erratically distributed chalcopyrite, tetrahedrite, freibergite, and occasional galena with a shell of zinc ore on the outer margin. Both the chimneys and the mantos are surrounded by imperfect shells of manganosiderite and sanded dolomite. The mineralization is of Laramide age. Hydrothermal alteration affects all rock units to varying degrees. Clay mineral alteration halos occur around the ore bodies. Hydrothermal solutions have developed sanded rock, rubble filled channels, and banded zebra textures, principally in the Leadville Limestone. Structural control of the ore bodies is not well defined. Both the location of the district and the chimneys are probably related to basement structures. The mantos are largely controlled by stratigraphic factors and a pre-Pennsylvanian karst topography in the Leadville Limestone, which were modified by hydrothermal activity, and by weak zones of northeasterly trending faults.

Jan 1, 1968

By C. A. Stiles, J. W. Nyhus

Erie Mining Co. is a 10.3-million-tpy pellet producer on the east end of the Mesabi Range 60 miles north of Duluth. Its complex includes facilities for mining, crushing, grinding and beneficiation in addition to a pellet plant and power plant. A 74-mile railroad links the mine and plant to Taconite Harbor on the shore of Lake Superior. The concentrate recovery ratio at Erie is about 1: 3, and this, along with stripping activity, makes it necessary for the company to mine nearly a million tons of material a week. At the outset, all crude ore mined at Erie was hauled entirely by rail, but with expansion into additional mining areas, the company made a gradual transition towards truck-to-rail haulage. Today, in Erie's 11th year of operation, over 50% of all crude taconite mined is transported by truck to loading pockets where it is transferred to rail cars. Future years will see more taconite moved in this manner. Thus, the company has an increasing interest in tire performance.

Jan 6, 1969

By Walter C, Smith

Metallic bismuth was known in the Middle Ages and the name is supposed to come from the German Wismut. The origin of the German name is uncertain. References to bismuth are found in the writings of Valentine, Paracelsus, and Agricola between 1450 and 1550. Early specimens of bismuth were very impure and often were confused with antimony, tin, and zinc. About the middle of the eighteenth century, J. H. Pott, C. J. Geoffroy, and Torbern Bergman succeeded in producing fairly pure bismuth and showed it to be an elementary metal similar in many respects to lead.

Jan 1, 1953

By E. P. Abrahamson II

The effect of transition elements which form binary solid solution upon the recrystallization temperature of zirconium has been investigated. All additions raised the recrystallization temperature. A correlation is obtained between the logarithm of the rate of change of recrystallization temperature with atomic percent solute and the free atom ground state electron configuration of the solute element. ThE work of Abrahamson, et al., on dilute binary solid-solution alloys indicated a correlation between the free-atom ground state electron configuration of the solute and either the brittle-ductile transition or recrystallization temperature. These studies were carried out on bcc base materials. The implication is that the outer s and d electrons of the solute are the prime determinant of the absolute rate of change of recrystallization or transition temperature. Furthermore, the limit of linearity has been shown to be a function of solute electron configuration for recrystallization in iron and vanadium. To date no Complete systematic recrystallization study of dilute binary zirconium base alloys has been made. It is the purpose of this study to note whether the change in solvent structure from bcc to hcp will influence the correlation. It was also desired to learn more of the role of the electron configuration of the solvent on recrystallization temperature. PROCEDURE All alloys were made using 99.87 pct Zr with 0.01 Cr, 0.04 Fe, 0.006 Hf, 0.003 Mg, 0.003 Mn, 0.003 N, and 0.080 0 (132 BHN). The solute elements were 99.9 pct pure. According to the published binary phase diagrams6 and metallographic examinations at X750, all alloys used were solid solutions. The alloys were arc melted and remelted six times in the form of cubic 200-g buttons under an argon atmosphere. They were then hot pressed at 950°C to 0.450 in., upset pressed to 0.350 in., and annealed at 800°C for 1 hr. The specimens were then Blanchard ground to 0.250 in., removing 0.050 in. from each side. The grain size of the material at this stage was found to be 8000 100 grains per sq mm. The specimens were then cold rolled to 0.130 in. and cold pressed to 0.125 in., yielding 50 1 pct cold work. All alloys were then chemically analyzed for the principal addition. The interstitial contents remained at the values of the starting material when checked on random alloy specimens. The rolled sheet was cut into 6.75 by 0.25-in. lengths and heat treated in a gradient furnace for 1 hr. The gradient was 250o to 900°C over the 6-in. length, recorded continuously by six thermocouples resting on each specimen. Control was 3oC, accomplished at the hot end. The recrystallization temperature was determined metallographically using polarized light. The criterion chosen was the point on the specimen showing the first recrystallized grain at a constant magnification, X200. Specimens were repeated, and the agreement was found to be 3°C. RESULTS Three different pure zirconium specimens were tested, and the recrystallization temperature was

Jan 1, 1962

By G. R. Speich, L. Zwell, H. A. Wriedt

HORNBOGEN1 has recently shown that it is possible to measure the degree of segregation accompanying cellular precipitation in ferritic Fe-Zn alloys by measuring the lattice parameter of the ferrite phase within the cell. In extending this work to study a wider range of composition and to evaluate the free-energy change accompanying the growth of the cells, the lattice parameter and the boundary of the a! phase in Fe-Zn alloys were redetermined to check the earlier work of Schramm.2 This appeared to be necessary since the Fe-Zn diagram has been drastically revised since the work of Schramm. Stadelmaier and Bridgers3 have recently shown that, contrary to prior belief: the y iron field is closed and the a phase boundary extends to an a + T + L peritectic at 782°C where peritectic a contains 42 at, pet Zn. The phase T in equilibrium with the a solid solution has a composition near Fe3Zn10 and a cubic 081 type structure.' The alloys were prepared by two different methods. In the first method carbonyl iron powder (400 mesh, 99.8 pet pure) and high-purity zinc powder (200 mesh, 99.99 pet pure) were mixed in a ball mill and then pressed in a die at 40,000 psi pressure to make compacts with a diameter of 5/8 in. and a thickness of l/4 in. These were sealed in evacuated quartz capsules, gradually heated to 1100°C over a period of 1 week (3 days at 600°C) 3 days at 800°C, 1 day at (1100°C), and then quenched in iced brine. For the alloys containing 23.4 and 30.1 at. pet Zn, the final homogenization anneals were performed at 1000" and 850°C) respectively, to prevent melting. In the second method, alloys were prepared by saturating high-purity iron millings (0.001 in. thick, 99.9 pet pure) in zinc vapor. For each alloy the impregnation was conducted at a fixed vapor pressure of zinc and a fixed temperature between 750' and 800°C. When saturated, the millings were quenched in water. The compositions of the alloys prepared by both methods are shown in Table I. The lattice parameters of the ferritic solid solutions were determined by comparing the 26 values of their 310, peaks (using Co Ka) or of their 211 , peaks (using Cr Ka) with those of corresponding peaks for high-purity a iron. The 20 values were measured at room temperature with an X-ray dif-fractometer (G.E.-XRD5). By using a fiducial value of 2.8664Å for the lattice parameter of pure a iron at 25oC,5 the lattice parameters of the zinc-bearing

Jan 1, 1964

By V. H. Whihelm

Since 1935 California has enjoyed a remarkable cycle of discovery, which has placed the state in a very satisfactory position in regard to oil reserves. Most ol the geophysical plays have been drilled and it is possible that new discoveries must be made by the application of careful geologic and stratigraphic studies. During 1940 only one new field was discovered, which, although not of major importance, may lead to additional discoveries. During the year, 113 wildcats were drilled. New discoveries, extensions and a reappraisal of discoveries made in 1939 will not approximate over 50,000,000 bbl., as against an estimated withdrawal during the year of 224,000,000 barrels. Demand in terms of crude for 1940 was 632,000 bbl. per day as against 626,000 bbl. per day for 1939. Demand for gasoline was the same as in 1939, but the demand lor fuel oil increased 3.8 per cent. Compared with 1939, Japanese shipments decreased from 75,786 bbl, per day to 61,000 bbl. per day, but the balance of Pacific foreign shipments increased from 59,409 bbl. per day to 61,304. Total with-drawals from storage during the year will approximate 7,000,000 bbl., almost all of which is fuel oil. Drilling activity was slightly greater than in 1939 and accounted for 890 new producing wells as against 851 for 1939 (Table 3). Production averaged 611,900 bbl. per day as compared with 614.,842 bbl. per day for 1939. The productive acreage figure of the state was increased by 4000 through discoveries and extensions. New Discoveries Los Angeles Basin District Del Vdle Field.—Northwest of Newhall, where the first oil well in California was drilled, R. E. Havenstrite completed his Lincoln No. I well, flowing 390 bbl. of 50" gravity oil together with 7000 M CU. ft. of gas. Later the well was recompleted, after cutting off the gas, for 950 bbl. of 34" gravity oil. The type of structure from which this production is coming is a plunging anticline, complicated by faulting. The Lincoln No. I well uncovered approximately 180 ft. of net sand. This field contains a gas cap and its indicated productive area approximates 500 acres. An intensive wildcat drilling campaign is expected during this coming year in the district in the vicinity of the Del Valle field. Extensions and Deeper Sand Developments Los Ange1es Basin District Athens Field.—On the northwest plunge of the Athens structure, the Thorley Oil Co. completed its No. 12-1 well, flowing 250 bbl. of 3 2" gravity oil from a depth of 8097 ft. The area in which the well is located is complicated by faulting and it is impossible at this date to determine the importance of this deep-zone discovery.

Jan 1, 1941