Search Documents

By W. P. Sykes

Seven years ago, Dr. S. L. Hoytl presented a masterful discussion of the hard metal carbides and cemented tungsten carbide. His lecture summarized most of the data then available in the field; many of the details relating to the production, properties and structure of cemented tungsten carbide had never been previously published, for, in fact, this information was only then being acquired. During the intervening years, the cemented carbides have assumed a place of real importance in the commercial field, with an ever widening variety of applications due to constant improvement in the control of production technique and the unremitting search for new compositions that might better the performance of the alloys in one or another type of service. The most recent summary of production methods, properties and guides for the successful application of the cemented carbides appears in the 1936 edition of the Metals Handbook. Of necessity, much detailed information relating to structures and physical properties is not included in such a summary, and it is with such details that the present discussion is concerned. Steps in Preparation While the past 25 years have contributed a valuable store of working knowledge in the field of powder metallurgy, many of the process controls are derived entirely from experience and are not as yet finally explained by a specific physical or chemical phenomenon. For most of the cemented carbides such difficulties are aggravated by our lack of knowledge not only of the complex alloy systems involved, but also by the possible changes in structure and even in composition which may accompany variations in temperature, heating time, and furnace atmospheres. The principal steps in the preparation of these cemented carbide alloys are fairly well known, but to supply a foundation for discussion these steps are briefly outlined as follows : 1. Formation of the metal carbide in the form of powder by heating a mixture of carbon and the metal powder or oxide for several

Jan 1, 1938

By W. P. Sykes

Seven years ago, Dr. S. L. Hoytl presented a masterful discussion of the hard metal carbides and cemented tungsten carbide. His lecture summarized most of the data then available in the field; many of the details relating to the production, properties and structure of cemented tungsten carbide had never been previously published, for, in fact, this information was only then being acquired. During the intervening years, the cemented carbides have assumed a place of real importance in the commercial field, with an ever widening variety of applications due to constant improvement in the control of production technique and the unremitting search for new compositions that might better the performance of the alloys in one or another type of service. The most recent summary of production methods, properties and guides for the successful application of the cemented carbides appears in the 1936 edition of the Metals Handbook. Of necessity, much detailed information relating to structures and physical properties is not included in such a summary, and it is with such details that the present discussion is concerned. Steps in Preparation While the past 25 years have contributed a valuable store of working knowledge in the field of powder metallurgy, many of the process controls are derived entirely from experience and are not as yet finally explained by a specific physical or chemical phenomenon. For most of the cemented carbides such difficulties are aggravated by our lack of knowledge not only of the complex alloy systems involved, but also by the possible changes in structure and even in composition which may accompany variations in temperature, heating time, and furnace atmospheres. The principal steps in the preparation of these cemented carbide alloys are fairly well known, but to supply a foundation for discussion these steps are briefly outlined as follows : 1. Formation of the metal carbide in the form of powder by heating a mixture of carbon and the metal powder or oxide for several

Jan 1, 1938

By M. C. Flemings, T. S. Piwonka

Pore formation is examined analytically in cellu-larly solidified single crystals, in cylindrical castings of pure metals and alloys, and in unidirectionally solidified castings. Effects are considered of fluid flow. dissolved gas, and surface tension. Experimental results show that flow through a partially solid "mushy" aluminum alloy obeys relations similar to those applicable for flow through other types of porous beds. Flow rate is proportional to the square of the fraction liquid (fL) for fL less than 0.3. Results indicate models chosen for mathematical description of pore formation in alloy solidification are valid. ONE of the solidification variables which is influential in determining mechanical properties of castings and of wrought material produced from cast ingots is porosity. This porosity may result from shrinkage, dissolved gases, or a combination of both, and may take the form of either macroscopic pores in localized areas of the casting or microporosity evenly distributed throughout large areas of the casting. In alloys which freeze over a range of temperatures some microporosity is generally found after solidification. There has been much discussion as to whether the micropores are caused primarily by shrinkage, by gas, or by a combination of both.'-3 There has, however, been little experimental or analytical work performed to delineate the relative contributions of shrinkage and gas in causing microporosity or to quantitatively describe the influence of processing variables on microporosity. Porosity other than microporosity (e.g., center line shrinkage) has also received only limited quantitative treatment.495 The aim of this work is to examine analytically the general problem of pore formation in solidification and to perform limited confirmatory experiments. Consideration is first given to shrinkage porosity in pure and nearly pure metals (shrinkage in cellular growth, centerline shrinkage in cylinders). Next, a discussion is given of formation of shrinkage-caused microporosity in unidirectional solidification and in "mushy" solidification. Finally, influences of dissolved gas and surface tension on microporosity are examined. Numerical results are given for aluminum and an aluminum alloy. Typical examples of microporosity are shown in Figs. 1 to 3, for 1) cellularly solidified aluminum, 2) sand-cast aluminum alloy, and 3) low alloy steel. SHRINKAGE POROSITY IN PURE AND NEARLY PURE METALS 1) Cellular Growth. In cellular freezing of an impure liquid, liquid grooves may exist over a considerable length of the growing crystal.6 The cross-sectional area of the grooves decreases with increasing distance from the cell tips; the root of the groove is blunt if the liquid at this point reaches eutectic composition. As a result of volume contraction during solidification, flow occurs down the groove, parallel to the growth direction; hence, there must be a pressure drop from the groove entrance to points within the groove. The geometry of the groove is simplified to that of a circular cylinder of radius r and length L, Fig. 4, L » r, and a simple and useful limiting case is obtained. This is that, in the circular cylinder freezing at constant velocity, the pressure at the root of the groove is lower than that pressure at radius r in grooves of other geometries where r decreases continuously to a lower limit at L. As discussed below, a pore resulting from a given pressure difference

Jan 1, 1967

By Harry V. Welch

This paper presents a brief discussion of numerous devices and processes which have been utilized for the recovery of values from gases in copper reduction works and describes in greater detail the development and application in recent years of electrical precipitation, more familiarly known as the Cottrell process, to the problems of dust losses with furnace gases in copper-smelting and refining plants. The field for collection of suspended particles in gases is widely extended in our modern complex, congested .and industrialized mode of living, and its satisfactory solution is required by our increasing appreciation of the extravagant waste, unhealthful effects and nuisance which such uncontrolled emission of solid suspensions represents. Much of the special dust-recovery equipment in use today has been developed in one industry and carried over to many others. The early work of Cottrell was with sulfuric acid mists, aimed at the purification problem in contact acid manufacture, but the present uses of Cottrell equipment cover a diversified field—carbon black, combustible gas, oil mists, iron blastfurnace fumes and dusts, cement-kiln gases, as well as the purification of gases in contact and chamber acid plants and its wide and extended use in the nonferrous metallurgical field of copper, zinc and lead, and their associated metals. Dust and fume collection from furnace gases became a problem only with the modern development of large and amply powered auxiliary furnace equipment, which in turn permitted large furnace units, fast driving and large outputs of finished product per unit of furnace capacity. The ancient metallurgist with his small clay pot and hand-operated bellows had too little gas velocity to cause a real dust loss. As furnaces grew in size, flues and stacks were added, and undoubtedly the first observable dust losses were indicated by the deposits in the flue and stack base. Large flues, it was noted, collected more than smaller ones, and the expansion of a portion of the flue into a chamber represented the first serious attempt at recovery of furnace dust losses. For a century or more the settling chamber represented the best of skilled metallurgical practice in recovery of furnace dust, and it may be said to have reached

Jan 1, 1934

By Charles W. Goodale

The purpose of this paper is to review the history of the Drumlummon, one of the famous old mines of the West. Mining engineers, when sent to examine new mines in old districts, or, to decide whether an old property, under new conditions, will pay to reopen, have had difficulty in learning anything authentic regarding workings which are under water, and historical facts about the working character of the ore, the total production, and the value of the ore with increasing depth. 'Not many years elapse after the pumps are pulled, before maps, books and records are destroyed, and the value of the publications of the Institute would be increased if they contained the history of many old mines now abandoned. The unsuccessful efforts of the writer quite recently in trying to obtain reliable information about a gold mine which was reported to have produced several million dollars between 1880 and 1888, the workings of which are now partially caved and under water, impressed upon his mind the desirability of having a permanent record of old properties. In this particular case, the owners insisted that under present conditions of improved methods of treatment —particularly by the use of cyanide, which was not an applied process when the mine was operated, the property could be made to pay a handsome profit on ore left in sight in the old workings, but no assay records could be found to confirm these assurances, and even the records of bullion shipments had been destroyed. If surveys and maps were made as the work progressed, no trace of them could be found, and therefore opening of the ground through a new shaft and drifts therefrom would be attended by some risk while exploring near the old workings. Fatal accidents by flooding under these conditions have occurred, and as an evidence that miners have fears of such dangers, it was urged upon the Mining Committee during a recent session of the Montana Legislature, by a delegation of

Jan 1, 1915

By Frederic L. Kadey

Diatomite is a siliceous, sedimentary rock consisting principally of the fossilized skeletal remains of the diatom, a unicellular aquatic plant related to the algae. Thus, it has-been formed by the induration of diatomaceous ooze, and consists mainly of diatomaceous silica, a form or variety of opal which is first formed in the cell walls of the living diatom. Diatomaceous silica is not generally regarded as a synonym or the equivalent for diatomite, although it has been so used at various times. Accurately, diatomaceous silica is the preferred name for the principal mineral component of which the rock, diatomite, is composed. The terms diatomaceous earth and kieselguhr are used as synonymous with diatomite. The designations tripoli, tripolite, infusorial earth, etc., were used at one time but are now obsolete. With the changing nomenclature, these terms that were at one time correct when proposed and used for generations would be considered incorrect if used today in the light of current knowledge. The designation diatomite is reserved for those accumulations of diatomaceous silica that are of sufficient quality, size, and minability to be considered of potential commercial value. Processed diatomite possesses an unusual particulate structure and chemical stability that lends itself to applications not filled by any other form of silica. Foremost among these applications is its use as a filter aid, which accounts for over half of its current consumption. Its unique diatom structure, low bulk density, high absorptive capacity, high surface area, and relatively low abrasion are attributes responsible for its utility as a functional filler and as an extender in paint, paper, rubber, and in plastics; and as an anti-caking agent; thermal insulating material; catalyst carrier; and chromatographic support; polish, abrasive, and pesticide extender to name a few representative applications. The United States is the principal producing country, although diatomite is found in numerous other locations.

Jan 1, 1975

By G. Horvay, J. G. Henzel

Nomograms and charts are provided which permit rapid determination of the mold-casting interFace temperature and the speed of solidification when a semiinfinite ingot is cast into a semiinfinite mold. The physical properties of the mold, the frozen metal, and the liquid metal are not assumed to be equal, but they are assumed to be temperature independent. The results are correlated with charts prepared by Paschkis and Hlinka—using Columbia University's Analog Computer—for the freezing of finite ingot slabs when a constant surface temperature is impressed, and with experimental cooling curves obtained by Pellini in sand and iron molds for 7 in.-sq steel castings. x = coordinate directed to right of zero (freezing direction) y = coordinate directed to left of zero (melting direction) e = position of freezing front (in x direction) ? = position of melting front (in y direction) $ = temperature (function of position and time) ? = fixed temperature 2L = width of finite slab Y = a fixed position in the semiinfinite mold, or the width of a finite mold (see Section 7) Properties y = density, lb per cu ft c = specific heat, Btu per lb deg F k = conductivity, Btu per ft hr deg F X = heat of fusion, Btu per lb k = k/Yc = temperature diffusivity, sq ft per hr* b - = = - heat diffusivity, Btu per sq ft deg F Vhr Subscripts 2 = pertaining to the still-liquid metal (case of freezing), or the medium which furnishes the heat (case of melting) 1 = pertaining to solidified metal (case of freezing), or to molten metal (case of melting)* 0 = pertaining to mold (case of freezing), or to the still-solid metal (case of melting) f = pertaining to fusion condition (eg.,?f - fusion temperature) i = pertaining to the location x = 0 (the mold-ingot "interface")

Jan 1, 1960

By Donald H. Beilstein

The St. Joe Minerals Corporation Lead Smelter and Refinery have been in continuous operation at Herculaneum, Missouri since 1892 as the Herculaneum Lead Smelting Division. Over the years, the plant has undergone many changes to increase production, improve the technology, reduce the cost of operations, and produce the highest grade of primary lead. The latest alterations were begun in 1950 and completed in 1970 and have resulted in the Herculaneum Smelter capacity being increased to in excess of 200,000 tons per year (180,000 metric tons). This increase has made the Herculaneum Smelter the largest in the United States, and second largest in the world. This paper will describe the Herculaneum Smelter equipment, processes, and material balances. Particular emphasis will be given to the McDowell-Wellman 10' x 100' (3 x 30 meter) up-draft sinter machine and ancillaries; to the new Heavy Smelting Department (blast furnaces and drossing section); to the new Lead Refinery and its automatic casting equipment and to the gas handling system including the 340 tons per day (305 metric) Sulfuric Acid Plant utilizing a -four pass converter. The description will include photographs, flow sheets, tonnages and assays where applicable.

Jan 1, 1970

By Roman Šejnoha, Karel Mazanec

A pronounced tendency for delayed fracture zoas observed in the martensite structure of low-alloy steels in the as-quenched condition. Cracks of predominantly intercrystalline nature nucleated and propagated at stresses substantially lower than the short-titne tensile strength of- the steels, and were observed even in hydrogen-free speciunens. The occurrence of delayed fractures in the as-quenched condition is interpreted as a supevposition of the effect of free dislocations generated during the martensite transforlnation, and of a weakening of the prior austenite grain boundaries caused by dynamic shocks exerted on the boundaries by growing martensite plates. AN important metallurgical problem, connected with the production and use of high-strength steels, is delayed fracture in martensitic structures. Such fractures occur in quenched steels as a result of prolonged loading with external stresses far lower than the short-time tensile strength of the steel. The same effect can be produced by sufficiently high internal stresses: it is well-known that quenched structures will in some cases crack intergranularly at room temperature if not tempered quickly enough even in the absence of any externally applied stress. In Troiano's papers1,2 on delayed fractures in high-strength steels, the fundamental role of hydrogen migrating under the influence of multiaxial stress towards the nuclei of cracks was found. Fig. 1 shows the typical relationship between stress and the time to fracture found by Troiano in hydrogen-charged high-strength steels. On the other hand, Shurakov 3,4 explains the realization of delayed fractures in martensite as due to a "quasi-viscous" behavior of the austenite grain boundaries immediately after the martensitic transformation. 1) MATERIALS AND EXPERIMENTAL METHODS Two low-alloy steels of commercial purity were used for the experiments reported in this paper. Their chemical composition is shown in Table I. The heats were melted in a laboratory furnace, cast to ingots, forged to bars of 3/4 in. diameter, and annealed. Machined test pieces were heat-treated as follows: Ni-Cr-Mo steel held at 900°C for 30 min and quenched in oil; Mn-Si-Cr steel held at 900°C for 30 min and quenched in water. For the delayed-fracture tests, notched cylindrical test pieces, Fig. 2, stressed in torsion, and unnotched cylindrical tensile-test pieces, 1/4 in. diameter, were used. The specimens were normally loaded with a constant static load 45 min after quenching for the torsional tests and 10 min

Jan 1, 1965

By O. B. Bucklen, J. P. Matoney, P. G. Meikle, R. L. Terry

INTRODUCTION The trend in the coal industry for many years has been to make every- thing "bigger and faster." This also holds true for loading and storage facilities. Where once a 1 million st per yr (910,000 mt/yr) mine was rare, 3-5 million st per yr (2,730,000-4,550,000 mt/yr) mines are not uncommon today in the bituminous industry. This great increase in production, made possible through mechanization, requires greatly improved loading facilities just to get the coal away from the mine. Also, there is a trend to- ward combining production from more than one mine and cleaning it in a single preparation plant. In addition to increased loading capacity, this frequently necessitates raw-coal storage and blending facilities. The development of the unit train with its attendant economics has contributed more than any other factor to the widespread construction of storage and high-speed loading facilities. In the export market, the construction of ever larger coal colliers has added to the need for faster and larger loading facilities. In this climate of rapidly changing technology, any written ac-

Jan 1, 1979

By Elmars Ence, Harold Margolin

A. J. Goldak and J. Gordon Parr (University of Alberta) —While we appreciate the difficulties involved in any investigation of this system, and we wish to congratulate the authors on their comprehensive efforts, there are several aspects of their paper that are not clear to us. 1) If the 6 phase is, in fact, isomorphous with Ti3Sn, it should not be designated Ti,Al. An 4B structure cannot be isomorphous with an ordered structure of the DO type. Anderko et al.' suggested that the structure be called Ti3A1, and we believe this to be a more reasonable designation. The confusion is compounded when the authors designate the phase Ti3Al—yet the composition limits of this phase (according to their diagram) are approximately Ti,A1 and Ti,Al. Further, while Pietro-kowsky is said to have pointed out that the structure of the 6 phase is isomorphous with Ti3Sn, we understand that this was only a suggestion that was not confirmed. Margolin and Ence do not appear to have presented any evidence to support the suggested isomorphism. 2) In referring to the precipitation observed microscopically during the initial breakdown of high A1 a during quenching, the authors state that "such precipitation is not likely to be detected by Debye-Scherrer techniques". We suspect that if the precipitate was visible by optical microscopy, it must have at least one dimension of the order of 1 or greater, and would therefore be readily detected by diffraction techniques. 3) The authors state: "The basis for this suggestion (that 6 forms peritectically P + L—6) is the observation that the ,'3 + 6 and 6 phase fields were

Jan 1, 1962

By Pol Duwez, H. E. Martens

The high temperatures encountered in the operation of jet engines have imposed most drastic requirements upon the materials used in their construction. There are two different approaches to the materials problem connected with the design of parts in contact with high temperature gases. The first approach is to use a material which will perform satisfactorily at a temperature comparable to that of the gas. The second approach is to use a cooling system so that the material is maintained at a temperature appreciably lower than that of the gas. Besides the conventional method of cooling by means of a liquid in contact with the material exposed to a high rate of heat transfer, a less orthodox method consists of making the part to bc cooled of a porous material', so that the cooling fluid can be forced through the pores, In this scheme, the temperature of the coolant moving in a direction opposite to that of the heat flow increases gradually while passing through the porous material, and the coolant forms a protective layer on the surface exposed to heat, This method, referred to as ((sweat cooling," was pro- posed at the Jet Propulsion Laboratory in September 1944, and the experimental work on the preparation of porous metals was started early in 1945. The sweat cooling method opens new lines of research in powder metallurgy by extending the field of application of porous metals. The porous metals available at the present time are used mostly as bearings or filters, and a rather limited number of alloys are made for these applications. In addition, the fabrication of bearings or filters does not require a very close control of the permeability, while in the case of sweat cooling such a control is of primary importance. In designing a sweat cooled part it is imperative to assure a given rate of flow of coolant under certain conditions of Pressure drop. Generally, the Proper pressure drop and the rate of flow of coolant are deduced from heat transfer and design considerations, and consequelltl~ the Permeability of the Porous metal to be used is also determined. It is therefore necessary for the designer to have available a continuous series of porous metals covering a range of permeability as wide as possible. Contrary to the requirements established in the fabrication of filters, the actual pore size of a porous metal intended for sweat cooling is of little consequence, except for its effect on permeability. The tensile strength is likely to be of great importance for some applications. Since the tensile strength of a porous alloy decreases with increasing porosity, an important problem is to develop porous alloys having the maximum permeability with minimum porosity.

Jan 1, 1949

By C. A. Bruch, W. E. McHugh, R. W. Hockenbury

EXPERIMENTAL results of the last decade have shown that both accelerator particles and reactor radiations produce significant changes in the properties of metals. These changes, called radiation damage, are important from both academic and engineering viewpoints. An understanding of the radiation damage produced by reactor radiations is difficult, because many kinds of particles having varying energies are present. Therefore, many fundamental studies are being conducted using accelerators in order to obtain nearly mono-energetic beams of various charged particles. Furthermore, many of these experiments are conducted at low temperatures in order to freeze in the radiation-produced lattice defects, after which the specimens are annealed to study the movement of the defects. It is found that although much of the low temperature radiation damage disappears by annealing at room temperature, a significant amount remains. Because there is no assurance that irradiation followed by annealing at a higher temperature will produce the same effect as irradiation at the higher temperature, and because there is an immediate interest in reactor radiation effects during exposures at and above room temperature, a major program is in progress at this laboratory to investigate some of these effects. This paper, representing a part of the program, compares the radiation damage to a group of metals which were exposed under nearly identical irradiation conditions. The metals, representing the three major crystal systems, include copper, nickel, titanium, zirconium, iron, molybdenum, and type 347 stainless steel. The effects of reactor radiations have been treated from a theoretical viewpoint by Seitz' and Ozeroff.' The problem considered by them has been the atomic displacements produced in an infinite medium by mono-energetic beams of both neutrons and charged particles. For reactor experiments, this treatment is not wide enough in scope, because specimens and reactor components are finite, and there are continuous energy spectra of the various particles. Therefore, the theoretical considerations will be extended in this paper to cover reactor conditions and the findings will be compared with the observed radiation damage. Experimental Materials—The six basic metals for this investigation were of commercial or higher purity, and the type 347 stainless steel was of commercial quality. These materials were supplied in various forms ranging from ingots to finished rods, and were fabricated to rods approximately % in. in diam and annealed for specimen stock. A summary of data pertinent to these materials is shown in Table I. The values for chemical compositions include both actual analytical values and typical values supplied by the manufacturer. More information concerning typical

Jan 1, 1957

By R. L. Templin

THE increasing use of aluminum and its alloys in commercial fields has demanded a better understanding of their machining properties. This fact is exemplified by problems that have arisen in the automotive and airplane industries, but many in other fields might be cited. As pure aluminum and its alloys in their various commercial conditions show appreciable differences in their machining properties, it is not surprising that quite divergent solutions have been offered for the machining problems encountered. However, if the fundamental requirements of the most suitable cutting tools for these metals are understood, these machining problems lend themselves more readily to satisfactory solutions. Since the machining of free cutting brass and mild steel is understood by most persons accustomed to working these metals, it may serve our purpose better to first make a general comparison of the tools more commonly used in machining these metals with the tools most suitable for machining aluminum, then proceed to a more specific discussion of the individual tools. COMPARISON OF CUTTING TOOLS Cutting tools commonly used for machining free cutting brass usually have little, if any, top and side rake; they are ground on a medium to coarse abrasive wheel and used without any cutting compound or with a cutting compound that has a paraffin base. Those ordinarily used for steel have some top and side rake, are usually ground on a medium to fine abrasive wheel, and are often used with soluble-oil cutting compounds. The proper tools for aluminum and its alloys should have appreciably more side and top rake than the tools for cutting steel; should have very keen edges obtained by grinding with fine or very fine abrasive wheels supplemented in many cases by hand stoning with an oil-stone; and should be used with suitable cutting compounds whenever possible. In many cases, tools suitable for machining aluminum and its alloys are not appreciably different from tools commonly used for cutting hardwoods. The front clearance of a tool most suitable for machining aluminum and its alloys should be about 6°, the top rake from 30° to 50°, making the total angle of the cutting edge of the tool from 35° to 55°. A side

Jan 1, 1928

By B. K. Larkin, H. R. Bailey

A model Of heat flow in an underground combustion process is studied. This model includes convection effects and thus is more general than previous studies which considered conduction as the only mechanistn for heat transfer. Both linear (tube run) and radial (field application) geometries are considered. The effects of ignition heaters, vertical losses and finite source width are considered for the linear case. The results are in the form of equations and are presented in graphical form for a number of cases. Convection effects increase frontal temperatures about 25 per cent over those computed for conductive transfer for typical field operating conditions. This increase in temperature is a result of heat being transported toward the front by the injection gas. Even greater temperature increases are realized as the per cent oxygen in the injection gas decreases. It is well known that compression costs are of considerable importance in estimating the economic feasibility of underground combustion. By assuming an ignition temperature for the combustion fuel, predictions of limiting conditions on fuel density and injection rate necessary to sustain the combustion zone are made. For typical field conditions, at least 0.75 lb/cu ft of fuel are needed with air as the injection gas. If the injection gas is 10 per cent oxygen and 90 per cent nitrogen, this figure is 0.69 lb/cu ft. INTRODUCTION The possibility of increasing oil recovery by underground combustion has been considered for many years. Recent field tests indicate that the underground combustion process is technically feasible. The economic feasibility depends to a large extent on the amount of air which must be injected to sustain combustion. Prediction of the success of employing underground combustion in a particular reservoir must be based on existing field tests, laboratory tube runs"' and solutions of mathematical or analog models. Vogel and Krueger5 devised an electrical analog of the heat transfer problem in an underground combus-ion process. They considered the problem of heat conduction from a cylindrical source with increasing radius assuming no vertical losses. Bailey and Larkin and Ramey solved the corresponding problem including vertical losses by considering a mathematical model of the conduction process. Ref. 9, 10 and 11 also present information related to the subject study. The present paper generalizes these results to include both conduction and convection mechanisms for heat flow. A model of the conduction-convection process is described. The partial differential equations governing this model are written and solved for a number of cases of interest. The formulas are evaluated and the results are presented graphically. A CONDUCTION-CONVECTION MODEL Description of the Model A number of models are employed in this paper, each of which approximate a particular physical situation depending on the geometry, i.e., linear or radial flow, the type of vertical heat losses, the nature of the source, etc. The geometry for both the linear and radial case is shown in Fig. 1. A particular linear model is described in this section, and variations from this model are described in later sections of the paper. Consider a homogeneous, semi-infinite porous prism with lateral sides insulated as shown in Fig. 1. The left end, x = 0, is heated for a time t, with a plane heater supplying a constant heat flux and during this time; gas (nitrogen) is passed through the pores of the prism at a constant mass flux. At time t, the heater is turned off and air is injected in place of the nitrogen. This causes combustion to take place, and a uniform source of width 1 is formed which moves at a constant velocity v, to the right. The frontal velocity v, is related to the gas velocity v,, through stoichiometric considerations

By R. F. Mehl, J. K. Stanley

THE recrystallization of cold-worked metals is studied ordinarily by determining the temperatures required for complete recrystallization to occur within a given arbitrary time period, usually within 15 min. to 2 hr. The results obtained are conventionally assembled in a three-dimensional diagram relating this temperature to the amount of cold-work (percentage deformation) and the resultant grain size, though sometimes other modes of representation are employed.1 Such three-dimensional diagrams are not complete, for the number of variables exceeds the number represented. The process of recrystallization is characterized by a time-rate, a fact that is not portrayed upon ordinary recrystallization diagrams. It is known that recrystallization consists in the formation of new nuclei and the growth of these nuclei, a process that continues until the matrix is completely consumed and the original set of grains entirely replaced by the new. This knowledge is old.2 Truly heterogeneous reactions invariably proceed by nucleation and growth; the decomposition of eutectoid solid solutions provides an example about which much is known,3 and freezing, originally studied by Tammann, provides the classic example. Although recrystallization is not a heterogeneous reaction within the orthodox meaning of the term, the mechanism of the process is the same. As in eutectoid inversion and freezing, it should be possible to study the rate of isothermal recrystallization as a function of time, and it should also be possible to analyze the isothermal reaction curve into the component rates of nucleation and growth that determine them.* Other methods, not employing the rates of nucleation and growth, have been used to represent the rates of such reactions, but these in general have been artificial and have not led to progress .4,5† The theory of recrystallization is not in advanced state; if recrystallization data were obtained in terms of the rate of isothermal recrystallization, and in terms of the rate of nucleation and the rate of growth of recrystallized grains, and in particular if the temperature coefficients of these rates were measured accurately, an adequate theory should be more readily developed .27 Such an effort requires proper experimental technique, but especially requires suitable methods of mathematical analysis to convert measurements made upon a surface of polish into values for the rate of nucleation and the rate of growth and to combine these into a rate of isothermal recrystallization. These methods are now

Jan 1, 1942

By G. L. F. Powell

Bulk samples of silver have beat undercooled lo a large degree in contact with crystalline siliceous and ceramic oxide materials, indicating lhat stable oxides and oxide compounds are not the heterogeneous nucleants which normally catalyze cryslallization within a feu degrees of the equilibrium freezing point. Since 400-g samples were undercooled 250°C in contact with cristobalite, it is concluded that the undercooling required for homogeneous nucleation of sil11er is greater than 250°C. Undercooling was Jacilitated by precleaning the crucibles with a high-fires -sure blast of gas. IN numerous experiments on the undercooling of metal melts it has been assumed that a solid glassy surface, being non crystal line, will have no effect in catalyzing crystal nucleation from the melt. Conversely, it is usually accepted that any crystalline surface, in contact with a metal melt, will catalyze nucleation of metal crystals from the melt at degrees of undercooling less than that at which homogeneous nucleation will occur. Both these assumptions were implicit in the claim that homogeneous nucleation was observed in experiments1'2 on the undercooling of small metal droplets (10 to 100 mp diam). The droplets were thought to be freed of suspended crystalline particles which would otherwise catalyze heterogeneous nucleation. They were supported on flakes of silica glass which were assumed to be amorphous, and therefore incapable of acting as substrates for heterogeneous nucleation. In later experiments, large samples of molten metal were undercooled to temperatures similar to those achieved by the droplet technique by melting in a fused-silica crucible3 or a boro-silicate glass slag.4 Since these samples were usually fully enclosed in glass at the moment of freezing, it seemed possible that nucleation was homogeneous when maximum degrees of undercooling were achieved, despite the large size of the samples (up to 500 g). In experiments on the undercooling of silver5 the metal was contained in vitreous silica crucibles, the

Jan 1, 1968

By E. L. Anderson, J. R. Long, R. S. Dean, F. S. Wartman

Titanium has been estimated to comprise about 0.65 per cent of the earth's crust and ranks fourth in abundance among the metallic elements suitable for engineering uses. In spite of this, applications of titanium for structural purposes have not as yet been developed. Its commercial exploitation has been largely confined to the chemical industries and the production of paints and pigments; no doubt because of the difficulties that lie in the way of preparing the pure ductile metal. Published reports, however, indicate that ductile titanium can be prepared and possesses some unique properties. This, together with the occurrence in this country of several important titaniferous deposits, has led the Bureau of Mines to investigate processes for the production of metallic titanium, methods required for its fabrication, and the properties that may be produced in this interesting metal. Methods of Preparing Metallic Titanium Many early investigators claimed to have isolated metallic titanium; but in the light of present knowledge, it seems that they really had produced various mixtures of carbides and nitrides that have a metallic appearance but are brittle, hard, and unworkable. The first metallic titanium pure enough to be malleable when cold was produced by Hunter1 in the early part of the twentieth century. Kroll,~ van Arkel,~ and Fast,4 subsequently confirmed the facts that pure titanium is a. ductile metal and that small amounts of impurities were responsible for previous reports of brittleness. When heated, titanium reacts chemically with various gases, such as hydrogen, oxygen and nitrogen; if the volume of gas thus absorbed is too great, the metal becomes brittle and unworkable. The principal difficulty in making ductile titanium is prevention of such contamination, and the success of a given process may be judged by the completeness with which it solves this difficulty in a practical manner. Of the gases mentioned, hydrogen is the least objectionable, since its absorption by the metal is completely reversible and, although dimensional changes occur and absorption of hydrogen embrittles the metal, the gas may be removed readily by heating in a high vacuum for a short time. On the other hand, the absorption of oxygen or nitrogen results in the formation of permanent solid solutions of the oxide and nitride, which cannot be decomposed by the strongest reducing agentsz with sufticient completeness to restore the inherent ductility of the metal. Because of

Jan 1, 1946

By J. R. Long, E. L. Anderson, R. S. Dean, F. S. Wartman

Titanium has been estimated to comprise about 0.65 per cent of the earth's crust and ranks fourth in abundance among the metallic elements suitable for engineering uses. In spite of this, applications of titanium for structural purposes have not as yet been developed. Its commercial exploitation has been largely confined to the chemical industries and the production of paints and pigments; no doubt because of the difficulties that lie in the way of preparing the pure ductile metal. Published reports, however, indicate that ductile titanium can be prepared and possesses some unique properties. This, together with the occurrence in this country of several important titaniferous deposits, has led the Bureau of Mines to investigate processes for the production of metallic titanium, methods required for its fabrication, and the properties that may be produced in this interesting metal. Methods of Preparing Metallic Titanium Many early investigators claimed to have isolated metallic titanium; but in the light of present knowledge, it seems that they really had produced various mixtures of carbides and nitrides that have a metallic appearance but are brittle, hard, and unworkable. The first metallic titanium pure enough to be malleable when cold was produced by Hunter1 in the early part of the twentieth century. Kroll,~ van Arkel,~ and Fast,4 subsequently confirmed the facts that pure titanium is a. ductile metal and that small amounts of impurities were responsible for previous reports of brittleness. When heated, titanium reacts chemically with various gases, such as hydrogen, oxygen and nitrogen; if the volume of gas thus absorbed is too great, the metal becomes brittle and unworkable. The principal difficulty in making ductile titanium is prevention of such contamination, and the success of a given process may be judged by the completeness with which it solves this difficulty in a practical manner. Of the gases mentioned, hydrogen is the least objectionable, since its absorption by the metal is completely reversible and, although dimensional changes occur and absorption of hydrogen embrittles the metal, the gas may be removed readily by heating in a high vacuum for a short time. On the other hand, the absorption of oxygen or nitrogen results in the formation of permanent solid solutions of the oxide and nitride, which cannot be decomposed by the strongest reducing agentsz with sufticient completeness to restore the inherent ductility of the metal. Because of

Jan 1, 1946

By P. D. Merica

The remarkable phenomena exhibited by the aluminum alloy known as duralumin were discovered during the years 1903-1911 by A. Wilm1,2 and have been described by him and by others. 3 4 5 6 The unusual feature of this alloy is the fact, as was shown by Wilm, that it can be hardened quite appreciably by quenching from temperatures below its melting point followed by aging at ordinary temperatures, which consists merely f allowing the material to stand at these temperatures. The hardness is not produced by the quenching alone but increases during the period of aging, which may be from one to three days. Cohn3, 5 gives data showing the increase of hardness of duralumin during aging, after quenching in water from about 450° C. Upon annealing, the alloy so hardened by aging is softened exactly as is hardened steel. The composition of this alloy usually varies within the following limits: Copper, 3 to 4.5 per cent.; magnesium, 0.4 to 1.0 per cent.; manganese, 0 to 0.7 per cent.; aluminum, balance; iron (as impurities), 0.4 to 1 per cent.; silicon, 0.3 to 0.6 per cent. Its density is about 2.85. It is used only in the forged or rolled condition. This alloy has been produced for some years commercially and is in demand for the fabrication of parts for which both lightness and strength are required, such as for aircraft. Its tensile strength will average 50,000 to 60,000 lb. per. sq. in. (3515 to 4218, kg. per sq. cm.) after appropriate heat treatment, such as that described by Wilm.

Jan 6, 1919