Search Documents

By C. S. Barrett

It has been observed that deformation in iron takes place by slip on (110) + {112) + (123) planesl, 2, but in silicon ferrite with low deformation temperatures or high silicon contents (exceeding 4 per cent) the authors have found that slip is confined wholly to (110) planes, at least with small amounts of deformation. The purpose of the present investigation was to determine the effect of this alteration of slip mechanism on preferred orientations in cold-rolled and recrystallized strips. Incidental observations on the effect of the recrystallization temperature were also made. The numerous determinations of the texture of cold-rolled iron and steel have been in satisfactory agreement as to the principal features of the texture (with the exception of a few conclusions that apparently have been based on insufficient data). The texture is chiefly one in which 11101 directions of the grains lie along the direction of rolling, with a deviation of a few degrees, and in which the (100) planes lie in the plane of the rolled sheet, with a deviation from this position chiefly about the rolling direction as an axis. This deviation about the rolling direction as an axis has been measured by different observers and lies between about 45" and 50" or 60" for iron5, 6, 9 and is usually in the neighborhood of 50" for mild stee16, 7, 8. The range of this deviation is a function of the percentage of total reduction8, 10. Post8 reported that it decreases with increasing percentage reduction, but apparently he studied only the surface material, which Gensamer and Meh17 found to be somewhat differently oriented from the material in the inside of the sheet. McLachlan and Davey10 found that the deviation also decreases with increasing percentage of total reduction for the material in the interior of the sheet and is independent of the percentage of reduction per pass. The deviation about the cross direction as an axis (the direction in the

Jan 1, 1937

By Jay R. Burns

TWO magnesium sand-casting alloys are commonly favored in the United States. These are referred to as H and C alloys (Dow Chemical Co.) or 4Mz65 and AM260 alloys (American Magnesium Corporation). Both are of an aluminum-zinc-manganese type. H alloy contains 6 per cent aluminum and 3 per cent zinc and is characterized by relatively good toughness. C alloy contains 9 per cent aluminum and 2 per cent zinc and is employed where high yield strength and pressure tightness are required. Examination of magnesium castings poured in Europe and England,'J however, demonstrates that H and C alloys are replaced by .%8 and AZ~I, respectively. That is, A8 reprcsents a magnesiurn alloy having superior toughness while A291 is suitable for high yield strength and pressure-tight applications. The basic difference between the .Ameri-can and European alloys is that the foreign alloys employ a somewhat higher aluminum content and less zinc than is found in H and C alloys. The mechanical properties of the alloys, when divided into high and low-aluminum groups, are quite similar, as determined from separately cast foundry-control type test bars ,In this paper the decrease of mechanical properties caused by any given amount of microporosity is measured for H, C, A8, and AZ~I alloys. The relative susceptibility of each of the four alloys to microporosity is also determined. Typical mechanical properties and nominal chemical analyses are reported in Table I. The apparent similarities between the two alloys in each group have led to considerable discussion as to the relative merits of each of the compositions.2 Popular points for comparison between the alloys have been the relative susceptibility of each of the four alloys to microporosity6 and the effect of this microporosity on their mechanical properties. It is primarily intended, in this paper, to show the

Jan 1, 1946

By Jay R. Burns

TWO magnesium sand-casting alloys are commonly favored in the United States. These are referred to as H and C alloys (Dow Chemical Co.) or 4Mz65 and AM260 alloys (American Magnesium Corporation). Both are of an aluminum-zinc-manganese type. H alloy contains 6 per cent aluminum and 3 per cent zinc and is characterized by relatively good toughness. C alloy contains 9 per cent aluminum and 2 per cent zinc and is employed where high yield strength and pressure tightness are required. Examination of magnesium castings poured in Europe and England,'J however, demonstrates that H and C alloys are replaced by .%8 and AZ~I, respectively. That is, A8 reprcsents a magnesiurn alloy having superior toughness while A291 is suitable for high yield strength and pressure-tight applications. The basic difference between the .Ameri-can and European alloys is that the foreign alloys employ a somewhat higher aluminum content and less zinc than is found in H and C alloys. The mechanical properties of the alloys, when divided into high and low-aluminum groups, are quite similar, as determined from separately cast foundry-control type test bars ,In this paper the decrease of mechanical properties caused by any given amount of microporosity is measured for H, C, A8, and AZ~I alloys. The relative susceptibility of each of the four alloys to microporosity is also determined. Typical mechanical properties and nominal chemical analyses are reported in Table I. The apparent similarities between the two alloys in each group have led to considerable discussion as to the relative merits of each of the compositions.2 Popular points for comparison between the alloys have been the relative susceptibility of each of the four alloys to microporosity6 and the effect of this microporosity on their mechanical properties. It is primarily intended, in this paper, to show the

Jan 1, 1946

By H. H. Uhlig

In our study of the mechanism of and the prevention of corrosion in stainless steels, it was considered of fundamental importance to obtain knowledge of the surface structure of such alloys. If corrosion resistance is due to a self-healing oxide layer, which like a paint film protects the underlying metal, it would be obviously relevant were the effort made to make the film less permeable and more adherent; for example, the surface might be expected to respond to an anodizing process, which is found successful in increasing the film thickness and corrosion resistance of aluminum. However, if passivity and corrosion resistance of stainless steels are due to another cause, the attack of the problem would follow another path. One of the most effective techniques for studying passivity and corrosion tendency is the measurement of the electrochemical potential. Not only can one determine by potential measurements whether a metal is active or passive, but also one can determine the degree of passivity and rate of transformation of passivity with time. Chemical media that build up or destroy passivity when in contact with the steel can also be classified by potential measurements. Something can be learned, too, of the effect of alloy additions such as molybdenum to 18-8, known to decrease corrosion of the alloy in chloride solutions. A study of alloys in previous investigations has sometimes included data on the electrochemical potentials. Tammann and Sotterl measured the electrochenlical potentials of alloys of iron-molybdenum and iron-chromium and reperted the critical concentration of molybdenum or chromium at which passivity initiates. Strauss2 made similar measurements for the iron-chromium system. The electrochemical potential3 has also been used to indicate carbide precipitated 18-8. In 18-8, heat-treated to precipitate carbide, active metal exists at the region of the grain boundaries, contrasted with passive metal within the grains, the active metal accounting for a resultant active potential. Several

Jan 1, 1940

By H. H. Uhlig

In our study of the mechanism of and the prevention of corrosion in stainless steels, it was considered of fundamental importance to obtain knowledge of the surface structure of such alloys. If corrosion resistance is due to a self-healing oxide layer, which like a paint film protects the underlying metal, it would be obviously relevant were the effort made to make the film less permeable and more adherent; for example, the surface might be expected to respond to an anodizing process, which is found successful in increasing the film thickness and corrosion resistance of aluminum. However, if passivity and corrosion resistance of stainless steels are due to another cause, the attack of the problem would follow another path. One of the most effective techniques for studying passivity and corrosion tendency is the measurement of the electrochemical potential. Not only can one determine by potential measurements whether a metal is active or passive, but also one can determine the degree of passivity and rate of transformation of passivity with time. Chemical media that build up or destroy passivity when in contact with the steel can also be classified by potential measurements. Something can be learned, too, of the effect of alloy additions such as molybdenum to 18-8, known to decrease corrosion of the alloy in chloride solutions. A study of alloys in previous investigations has sometimes included data on the electrochemical potentials. Tammann and Sotterl measured the electrochenlical potentials of alloys of iron-molybdenum and iron-chromium and reperted the critical concentration of molybdenum or chromium at which passivity initiates. Strauss2 made similar measurements for the iron-chromium system. The electrochemical potential3 has also been used to indicate carbide precipitated 18-8. In 18-8, heat-treated to precipitate carbide, active metal exists at the region of the grain boundaries, contrasted with passive metal within the grains, the active metal accounting for a resultant active potential. Several

Jan 1, 1940

By H. H. Uhlig

IN our study of the mechanism of and the prevention of corrosion in stainless steels, it was considered of fundamental importance to obtain knowledge of the surface structure of such alloys. If corrosion resistance is due to a self-healing oxide layer, which like a paint film protects the underlying metal, it would be obviously relevant were the effort made to make the film less permeable and more adherent; for example, the surface might be expected to respond to an anodizing process, which is found successful in increasing the film thickness and corrosion resistance of aluminum. However, if passivity and corrosion resistance of stainless steels are due to another cause, the attack of the problem would follow another path. One of the most effective techniques for studying passivity and corrosion tendency is the measurement of the electrochemical potential. Not only can one determine by potential measurements whether a metal is active or passive, but also one can determine the degree of passivity and rate of transformation of passivity with time. Chemical media that build up or destroy passivity when in contact with the steel can also be classified by potential measurements. Something can be learned, too, of the effect of alloy additions such as molybdenum to 18-8, known to decrease corrosion of the alloy in chloride solutions. A study of alloys in previous investigations has sometimes included data on the electrochemical potentials. Tammann and Sotter1 measured the electrochemical potentials of alloys of iron-molybdenum and iron-chromium and reported the critical concentration of molybdenum or chromium at which passivity initiates. Strauss2 made similar measure-ments for the iron-chromium system. The electrochemical potential' has also been used to indicate carbide precipitated 18-8. In 18-8, heat-treated to precipitate carbide, active metal exists at the region of the grain boundaries, contrasted with passive metal within the grains, the active metal accounting for a resultant active potential. Several

Jan 1, 1939

By R. H. Swallow, George Hess

Aerial photography was once a crude, uncertain tool. Today it is a precision mapping instrument which saves important time and money for strip mining and other industry. Aerial photography began in the boxkite days of aviation. The Army first used it for rough reconnaissance photographs. Then, in the early Twenties, industry began to use aerial photographs of their plants and facilities for advertising or annual reports. The quality of these pictures was not very good by today's standards, but this work began the development of better cameras, better lenses, better photographic techniques.

Jan 1, 1949

By T. Carl Shelton

The coal industry of the United States in 1967 had reasons to be both exuberant and concerned about its present and future role in the economy of the country. Continuing a momentum that began in the early 1960's, the industry has moved ahead in providing competitive customized products to strengthen its long-term domestic and foreign commitments, and has maintained with steady progress its position as a major supplier of energy. On the other hand, the industry must overcome air- water pollution and conservation-reclamation problems that have been identified by 1967 legislation. Throughout the year, the industry was characterized as "progressive," "healthy" and "dynamic." To have been termed a "growth industry" in 1967, is an accolade the coal industry can accept with pride. Culminating its efforts throughout the decade, the industry has emerged with a competitive image that is representative of its future strength.

Jan 2, 1968

By George S. Rice

GROUND movement from mining, whether it be for coal, metal, industrial minerals, or .oil, will always present many difficult problems. These are especially serious when valuable surface improvements may be badly damaged. The mine itself, if mining methods are not suitable to the formation, is subject to heavy falls of the main roof in the working places; and with certain structural conditions the movements may cause in coal mines disastrous bumps and outbursts of gas, and in deep metal mines rock bursts. In open-cut work rock and earth slides may result. Absolute prevention of ground movement from mining is impossible unless large pillars are left unmined,

Jan 1, 1937

By Harry H. Power

WORK of the Committee on Education of the Petroleum Division has been under way for approximately-one year. Although some progress has been made, further activities of the Committee are necessary in order to discuss mutual problems more thoroughly by a unified group interested primarily in this field of specialization.

Jan 1, 1944

By R. S. Dean

PROCESSES for the direct production of iron and steel from ores are hardy perennials, and new processes and revivals of old ones are continually being brought to the attention of the investing public if not to the attention of metallurgists. Direct production of iron and steel is so simple that it offers a fertile field for the promoter. Unfortunately in this way direct processes have acquired a bad name, not always deserved, with conservative capitalists and metallurgists. Direct processes cannot, except in special instances, be looked upon as a substitute for any single operation in present iron and steel practice but must be considered, as one link in an entirely new chain of metallurgical process from ore to finished steel. Thus it is, in my opinion, inadvisable to consider the use of sponge-iron processes as a means of treating ore of ordinary blast-furnace grade to produce open-hearth feed. In time I think it will be found equally inadvisable to smelt iron-ore concentrates in the blast furnace.

Jan 1, 1935

By C. R. Breck

THERE has been a running discussion over the past several years with respect to the life and adequacy of our natural gas reserves. Some of the experts agree on one phase of the subject at least-that eventually it will be necessary to augment deliveries of natural gas in the northern markets by the development of a more or less comparable synthetic gas made from coal. The purpose of this paper is to point out: 1. It may be later than a good many people think-the demand for addi¬tional domestic and commercial pipeline gas in at least one section of the North will probably be felt rather keenly before an adequate synthetic pipe¬line-gas project, developed on economic lines, could be completed, even if initiated in the near future. 2. The evidence is considerable that such a project would be technically sound and economically self-supporting, although the margin of profit at first might be so small and the magnitude of an economic enterprise so great -that financing would be impossible without Government aid in some form or other. The part of the country referred to is the heavily populated section in the northeast of the United States. To simplify an examination of the situa¬tion, let us take the potential marketing areas within range to the north and east of the three pipelines: 1. Tennessee Gas Transmission Co. as it enters Erie County, New York state. 2. Texas Eastern Transmission Corporation just before the tap that sup¬plies the general Philadelphia area. 3. Transcontinental Gas Pipe Line Corporation as it enters the state of New Jersey. The sources of gas for these three pipelines are in Texas and Louisiana. The ultimate maximum combined capacity of the three lines at the points stated is approximately 1,200,000,000 cu ft per 24 hr at the maximum load factor probable of attainment in normal operation. The areas supplied by the three lines north and east of the points stated, or assumed as eventual markets, are: 1. Central New York state, from Buffalo to Albany (both inclusive).

Jan 1, 1953

By H. I. NORTON, H. O. Hofman

ZINC smelters in the central western. States have established a very high standard of purity for blende-concentrates, viz., zinc 60, iron less than 3, and lead less than 1 per cent. The very low percentage of iron is made possible by the blende containing less than 0.5 percent of isomorphous iron sulphide and by the sparing occurrence of pyritic material in the large blende-deposits of southwestern Missouri and southeastern Kansas. The blende in these districts occurs in sub-Carboniferous limestone, and is associated with chert, residual clay, calcite, pyrite or rnarcasite and bitumen. The different minerals are coarse and therefore readily separated by mechanical washing from the blende, with the exception of pyrite and marcasite, as blende has a specific gravity of from 3.9 to 4.1, marcasite, from 4.85 to 4.90, and pyrite, from 4.95 to 5.10. The common procedure of dressing the ores is to crush in a breaker, size in a trommel with 0.5-in. holes, pass the over-size through roughing-rolls and then jig the ore, now reduced to 0.5 in. maximum size, in roughing multiple-sieve jigs. The products of these are waste-tailings, sine-discharge coarse concentrates, side-discharge coarse middlings and bottom-discharge fine middlings. The coarse concentrates are sent to the market. The coarse middlings are crushed in middlings-rolls and brought back into the system by feeding into the main trommel. The fine middlings are cleaned upon finishing-jigs. Any pyrite or marcasite present follows the blende and increases the percent-

Mar 1, 1905

By P. E. Fitzgerald

SOME readjustments in the research programs of most of the oil companics and petroleum engineering schools have been made necessary by the war. The most obvious change has been the conversion from production engineering to problems more closely related to the nation's was effort. Many laboratories now devote much of their time to studies on products to be derived from petroleum. such as synthetic rubber, toluene, and substitutes for critical materials. Others are working to improve motor fuels including high-octane gasoline and the special lubricants required by the wide geographical range of the present conflict. Of great importance is the experience of the geophysicists, who are now devoting a great percentage of their time on instrument research and production or special apparatus required by the armed forces.

Jan 1, 1943

By Michel David

One of the most important questions that arises in ore estimation can be stated as follows: What is the error when one extends the grade of a sample to a certain volume? The theory of regionalized variables, with the concept of extension variance, provides a response to that crucial question for any kind of sample extended to any volume. For the usual "extensions" encountered in current mining practice, some simple results can be derived from that theory which was initiated by Dr. G. Matheron. These results have been applied to a stratiform lead-zinc deposit for which several estimations of grade, tonnage and related precision have been made for a series of grid sizes such as might be used in a progressive exploration program.

Jan 1, 1969

By E. D. Hummer

During the planning of the fine coal cleaning addition at the Gary, W. Va., Coal Preparation Plant of United States Steel Corp. careful consideration was directed toward the problem of minus 48 mesh refuse disposal. The plant flow sheet included wet screening the raw coal at ¼ in., pumping the minus ¼ in. raw coal to bowl desiltors for desliming, and then cleaning the deslimed raw coal on tables. The material to be removed from the circuit as minus 48 mesh refuse consisted of the minus 100 mesh desiltor overflow thickened in two 120 ft diam thickeners and minus 1 mm screened from the table refuse. Later a flotation plant was added to recover coal from the desiltor overflow, and a classifier replaced the screens to make a sharper size separation of the table refuse at 48 mesh. Today the minus 48 mesh refuse at Gary consists of thickened flotation tailing and thickened spiral classifier overflow. The transportation of large quantities of fine, wet refuse filter cake mixed with jig and table refuse over existing conveying equipment would have been neither dependable nor economical. Filtration was therefore impractical, and disposal of the fine materials was a problem. The decision was to pump the material to storage ponds.

Jan 3, 1965

By Robert D. Pehlke, Arden L. Bement

A mass transfer coefficient for the removal of hydrogen from liquid aluminum by inert flush degassing has been determined experimentally at 700°C. A mathematical model has been derived, assuming transport control, which adequately describes the experimental data. The removal of hydrogen is shown to increase with decreasing bubble size, and with increasing flow of flushing gas. The presence of hydrogen in liquid metals in amounts which exceed the solid solubility at one atmosphere hydrogen pressure is highly undesirable, causing unsound ingots or castings, or resulting in difficulties during further fabrication. The removal of hydrogen from liquid metals can be accomplished by several methods, the principal two being vacuum treating and inert flush degassing. The design of a process involving either of these techniques is based on the mass transfer coefficient for hydrogen between the liquid metal and a hydrogen-dilute gas phase. In an effort to extend our knowledge in this area, an investigation of the rate of removal of hydrogen from liquid metals by inert gas flushing was undertaken. In view of the difficulties encountered with gas porosity in the casting of aluminum and aluminum alloys, and because of certain experimental advantages, liquid aluminum was selected for the study. PREVIOUS INVESTIGATIONS The removal of gases from liquid metals, particularly steel, has received considerable attention in recent years, The first definitive work of a theoretical nature was presented by Geller1 who considered the case where equilibrium exists between purging gases and metal bath during flushing, and also deviations from this ideal case. Hulme2 has surveyed a number of experimental studies and discussed some of the practical limitations of removing dissolved gases from molten metals. More recently a number of studies have been reported on degassing of steel melts by flushing with an inert gas.3'4 Considerable work has also been reported on aqueous and organic liquid-gas systems, and an excellent summary prepared by Hovis.5 The treatment of liquid aluminum by a flushing gas to remove dissolved hydrogen has been known for several decades.6 A number of gases have been used for this purpose, including nitrogen, argon, and chlorine, or mixtures of these gases. Tikkanen and Erkko7 have studied the relative density changes of aluminum castings poured from melts degassed with chlorine, nitrogen, and mixtures of the two gases. Their

Jan 1, 1962

By E. P. JENNINQS

(Cleveland meeting, October, 1912.) LARGE deposits of titaniferous iron-ore occur at Caribou, an old silver-mining camp in Boulder county, Colo., 17 miles west by south of Boulder, and a few miles northwest of the tungsten-mines. Professor Regis Chauvenet 1 published a part analysis of the ore many years ago, but gave no description of the wall-rock. Caribou hill, which contains both the silver-bearing veins and the iron-ore deposits, is a low dome of gabbro surrounded by the Archaean schists and gneisses of the Front range of the Rocky mountains, the peaks of which, a few miles west of Caribou, attain an elevation exceeding 12,000 ft. The gabbro stock is roughly elliptical in outline, with approximate diameters of 1 and 3 miles. The crest of the dome is 10,500 ft. above sea-level, and the town and ore-deposits are 500 ft. lower. Outcrops of the iron-ore occur in the town and extend NW. for 2,000 ft., where they disappear under the swampy meadows of Caribou park. Portions of the deposit are covered by drift, but one continuous outcrop is 900 ft. long and from 200 to 250 ft. wide. A second deposit is 0.25 mile south of the town along the eastern slope of the hill. It is not as well defined as the north bed, but is approximately 1,000 ft. long and from 100 to 200 ft. wide. The easily disintegrated ore does not form prominent outcrops, but the outlines of the deposits are readily traced by the large amount of ore fragments that cover the ground. Trenches and pits sunk on the outcrop expose a roughly banded magnetic iron-ore, with pyroxene as the principal gangue-mineral. The Gabbro. This rock was classified in the field as a gabbro from the presence of pyroxene and striated feldspars, and for convenience the field-name will be retained. 1 Chauvenet, Regis, Biennial Report of State School of Mines, Golden, Colo., p. 16 (1886).

Oct 1, 1912

By Albert Sauveur

Jan 1, 1924

By Albert Sauveur

Jan 1, 1924