Search Documents

By J. O. Brittain, N. R. Adsit

A number of zinc bicrystal specimens with the grain boundary loaded in simple shear were plustically deformed in creep in a vacuum at 200°C and under an argon atmosphere at 350°C. The results indicated that the amount of grain boundary sliding at a given time was controlled by the slip in the grains and was proportional to the resolved shear stress on the slip plane. Curves of grain boundary sliding vs time were found to be cyclic with no regular periodicity. ALTHOUGH grain boundary sliding (G.B.S.) has been investigated in a number of different types of tests on various materials there is substantial disagreement on the interpretation of the various observations. Gifkins1 has presented a comprehensive review of the subject of G.B.S. and fracture. He reports that the activation energy for high-temperature creep is equal to that for volume self-diffusion and that pure metals show less tendency towards intercrystalline fracture than alloys. Pure metals show appreciably greater grain boundary migration than alloys, and both grain boundary migration and grain boundary sliding follow the same general trend in time as plastic deformation during creep.' While there have been a number of different mechanisms proposed to account for G.B.S., none of the models explains all the results. Since zinc has only one prominent slip system, it was hoped that experiments on G.B.S. in zinc bicrystals might enable us to separate the effect of grain boundary angle and the effect of matrix slip and thereby resolve at least one part of this complex phenomenon. EXPERIMENTAL PROCEDURE Bicrystals of pure zinc (99.99 pct) were grown by a Bridgeman technique in a furnace having a gradient of 20°C per in. The bicrystals were seeded to a desired orientation and grown in a split graphite mold which was 3/4 by 5/8 by 8 in. The mold was enclosed in a Pyrex tube and the tube was evacuated and then filled with a small amount of argon before it was placed in the furnace. The growth rates were 1/2 to I in. per hr for the bicrystals and 1/2 to 3 in. per hr for the single-crystal seeds. The longitudinal V notches served to hold the grain boundary in position during the growth process. A schematic rep- resentation of a specimen which had been cut with a jewelers saw from the bicrystals is shown in Fig. 1. All specimens of a series were cut from the same crystal, some of which were 7 in. in length. After specimen preparation the boundary was approximately 5/16 in. long and the V notches had a radius of 1/16 in. The boundaries were straight at a magnification of X100 with the exception of a few which had a gradual radius of curvature of greater than 3.2 in.-1. Laue back-reflection photograms were taken on the specimens to check the orientation of grains in the bicrystals. The method of relating the orientation of the two lattices is shown in Fig. 1, where 0 is the angle between normal to the boundary and the trace of the basal plane, is the angle in the boundary between the trace of the basal plane and a line parallel to the V notch, and x is the angle in the basal plane between the Burgers vector and the perpendicular to the grain boundary. After mechanical polishing the specimens were chemically polished.2 Subsequent to the polishing operation the specimens were encapsuled under a vacuum of better than 25 annealed at 340°C for 1 hr to remove the effects of this handling, and again chemically polished. Finally, fiduciary marks were scribed on the specimen using a micromanipulator. Creep tests, which were conducted in a modified Bausch apparatusS with the boundary loaded in simple shear, were run at a constant load (since the boundary area remained essentially constant this is approximately constant grain boundary stress). The temperature was controlled to ±1/4°C as measured on a semiprecision potentiometer with a calibrated thermocouple. The specimens were tested in a vacuum of better than 0.5 at 200°C and in purified argon at a pressure of 1/2 atm at 350°C. The op-

Jan 1, 1965

By Merlon C. Flemings, Theodoulos Z. Kattamis

Examination was made of the distribution of tnanganese and nickel in colutrrnar dendrites of a cast low-alloy steel; more limited work was corzducted on chromium. Corresponding "segregrction ratios" were calculnted and shown to be relntivelv insensitive to cooling rate (''segregation ratio" is defined (Is the ratio of maximum to minimum concentrations within a volume whose dimensions are the order of the dendrite-arm spacing). Isoconcentratiorl curves were determined by the electron micropvobe and by rt7etallografihic studies on specimens subjected to isothermal-transformation treatments. From construction of isoconcentration curves, morphology of columnar dendrites is descvibed as intermediate between Perfect rodlike and sheetlike morphologies. The study is extended to equiaxed dendrites and it is shown that the strcture of these dendrites is sittlilar in many respects to that of columnar dendrites. On the basis of tlze sheetlike morphology of dendrites, a simple model is pvoposed for calculation of honzogenization kinetics. Results of trzatllevlatical analysis brcsed on this utzodel are given. This analysis relates residual segregation to time at homogenization temperature; it is in agreement with experiment. Calculations are given which show that even for relatively rapidly cooled material (of 1-ine dendrite-artn spacing) treatmets at 1200°C or above are necessary to achieve slgxificant Izomogenization of elenlents other than carbon itz reasonable time (e.g., rnangclnese, nickel). Conlplete homogenization of carbon is obtnined at much lowev tenlperatures (below 870°C). IN dendritic solidification of castings and ingots, solute redistribution during freezing results in mi-crosegregation of most alloy elements. The micro-segregation is such that minimum solute concentrations occur at the center of dendrite arms and maximum concentrations occur between dendrite arms. Residual segregation after subsequent therma1 processing (homogenization) depends on maximum and minimum initial concentration, on the detailed geometry of the isoconcentration surfaces within interdendritic regions, on the diffusion coefficient of the solute, and on time of thermal processing. The objective of this work was to determine, for a low-alloy steel, maximum and minimum concentrations, and the geometry of isoconcentration surfaces, primarily in order to permit calculation of homogenization kinetics. Most of the work reported was conducted on Samples from a unidirectionally solidified, fully columnar ingot. This type of ingot is made by extracting heat during solidification from one face; techniques for accomplishing this have been discussed.' Samples were taken at several locations, up to 5.75 in. from the mold chill face; the bulk of the work was performed on samples at 5.75 in. Alloy cast was, nominally, 0.4 pct C, 1.8 pct Ni, 0.8 pct Cr, 0.7 pct Mn, 0.25 pct Mo, 0.3 pct Si, and the balance iron. Brief study was also made on samples from an ingot which solidified with equiaxed grain structure. SAMPLE PREPARATION AND ANALYSIS Samples for electron-microprobe analysis were incorporated in mounts that included pieces of electrolytic nickel, chromium, and manganese, in order to normalize the intensities of these solutes in the specimens; also, a piece of electrolytic iron was included to measure the background. All specimens were polished in the usual metallographic manner. After the microprobe traces were made, the path was revealed by etching the specimens with picral. All microprobe analyses were made by point counting, integrating for 30 sec. The distance between points was fixed from 2 to 10 p, according to the precision desired in each case, the fineness of the structure, and the concentration gradient existing in a given area. (The distance was chosen 2 to 5 p near the maximum-concentration regions and 5 to 10 p near the minimum concentration.) The "take-off" angle for the A.R.L.-Model No. 21000 microprobe employed was 52.5 deg. Samples for metallographic analysis of isoconcentration curves were prepared by austenitizing at 1540°F for 20 min, quenching to the nose of the TTT curves (1200°F), heat treating isothermally at this temperature for a given time 0, and then quenching to room temperature. Due to concentration gradients existing in a dendritic structure, no transformation will take place for a given time 0 of isothermal heat treatment in the regions where the a.lloy concentration is higher than a given limit. Thus, the dendrite appears limited by an isoconcentration curve and can be made to appear to grow by varying the time of isothermal heat treatment.

Jan 1, 1965

By E. T. Turkdogan, L. E. Leake

A number of measurements have been made on the vapor pressure of pure iron at 1600°C. Experiments were carried out by the transportation method in which a sample of iron is exposed in a furnace to a stream of pure argon, metered at a predetermined flow rate for a specified period of time. The vapor pressure was obtained from the weight loss of the sample. A detailed diagram of the apparatus used for the experiments is given in Fig. 1. It consisted of a horizontal molybdenum-wire-wound furnace fitted with a recrystallized alumina tube 1 1/8 in. internal diam. The boats, 1 by 3/16 by 1/8 in., were fired in argon at 1600°C to constant weight before use. After this treatment, subsequent heating of the boats to 1600°C gave little or no further change in weight, e.g. ±0.05 mg in 24 hr. The furnace and reaction tube were separately fed with argon from two independent flowmeters. These were connected to a common supply source via an argon purification furnace containing metallic titanium sponge at 700°C, and an anhydrone drying-tower. A rotary displacement-type meter was included in the gas train to provide a direct means of measuring the total volume of gas passed through the reaction tube. The material used was vacuum melted high-purity iron in the form of wire 2mm in diam. The following impurities were present in the iron: 0.008 pct C, 0.002 pct Si, 0.005 pct Mn, 0.008 pct S, 0.001 pct P, 0.01 pct Ni, 0.001 pct Cr, 0.006 pct Cu, and 0.001 pct Al. Samples consisting of three small pieces of this wire were laid end to end in a recrystallized alumina-combustion boat, and were separated by small fragments of alumina. The wire samples were then melted in argon to form spherical beads 2 to 3 mm in diam. After weighing, the boat with its contents was placed on the boat carrier and introduced into the cool end of the reaction tube. The entire furnace system was then flushed with argon for 30 min. At the end of this period, the flow of argon to both furnace and reaction tubes was adjusted to the desired level; then the boat was slid rapidly into the hot-zone of the reaction tube. After a known volume of gas had passed through the reaction tube, the boat was withdrawn quickly to the cool end of the furnace. When quite cool, the boat was removed from the fur-mace and placed in a desiccator for subsequent re-weighing. The semi-micro balance used in these experiments had a sensitivity of 0.005 mg. The above procedure was repeated at several flow rates within the range of 25 to 300 ml per min. The flow of argon in the annular space between the two tubes was at a rate of 300 ml per min in all experiments. During all the experiments the furnace temperature was maintained at 1600° ± 5°C by means of a temperature controller. The temperature of the reaction zone was measured with a Tinsley high precision disappearing filament pyrometer which was initially calibrated against a Pt-13 pct Rh/Pt thermocouple; the errors due to temperature measurements were within * 5°C. RESULTS Assuming that the iron vapor is in the monatomic state, the vapor pressure can be calculated from the weight loss of the sample and the volume of the carrier gas. The results obtained are plotted in Fig. 2 against the rate of flow of argon through the chamber containing liquid iron beads. At low flow rates, the thermal diffusion of iron gives an apparent high vapor pressure, but at high gas flow rates, the carrier gas is not saturated with the vapor, and therefore, low vapor-pressure values are obtained. This is now a well-known phenomenon. There is a distinct inflexion of the curve at about 120 to 160 ml per min rate of argon flow and the vapor pressure of iron within this

Jan 1, 1961

By H. A. J. Wilkens, H. B. C. Nitze

From time to time papers treating of specific cases of Southern gold-mines and mining have appeared in the Transactions of this Institute, as well as in other journals and publications. Mr. George I?. Becker, of the United States Geological Survey, made a reconnaissance of the Southern Appalachian gold-belt during the fall of 1894; the results of his investigations are published under the title of "A Reconnoissance of the GoldFields of the Southern Appalachians," in the Sixteenth Annual Report of the Director of the United States Geological Survey, 1894-95 : Part III., " Mineral Resources of the United States." Mr. Becker has treated the subject mainly in a scientific geological manner. We present this paper to the members of the Institute as requested by the Secretary last May, with the object of covering the ground from a more practical and technical standpoint. The notes for this paper were made in a large measure from personal observations, gained chiefly during the past summer on a trip through the field. In connection with this trip we collected a suite of typical hand-specimens, representing the gold-ores and wall-rock from the more important localities. This collection forms a part of the exhibit

Jan 1, 1896

By G. W. LAAiIBOURNE

FEW mines possess a history of more fascinating interest than the Ontario at Park City, Utah. The famous Bonanza's production record of over $50,000,000; the great extent of its workings; the remarkable character of its mineralization; the fact that recent discoveries have shattered preconceived theories of the geology of the camp practically assuring the half-century old property a future as active and as prosperous as the past make the Ontario one of the unique mines of the world. A mere accounting of the wealth created by this historic property not only exemplifies the great profits

Jan 1, 1925

By John J. McCabe

INTRODUCTION Over the years, Congress has written into the Internal Revenue Code various provisions aimed at lessening at least one financial burden faced by taxpayers in the mining industry - the federal income tax burden. These provisions include the election to deduct exploration expenses, the election to defer deduction of development expenses, and the percentage depletion deduction. Careful tax planning from the very beginning of a mining venture is essential in taking maximum advantage of these tax benefits. A major decision to be made is the choice of organizational structure. (For a more detailed discussion of this subject, see McCabe, John J., "Developing Structures for Investments in Mineral Property," New York University Institute on Federal Taxation, 42 NYU 24, 1984). One such structure is the use of multiple corporations, with mining activities conducted by one corporation and nonmining activities, such as manufacturing, financing and administration, conducted by the other corporation. This technique, which will be discussed in detail below, can be particularly advantageous in delaying recapture of previously deducted exploration expenses and in maximizing depletion deductions. TAX BENEFITS IN MINING Exploration Subject to certain restrictions discussed below, exploration expenditures (i.e., expenditures paid or incurred during the taxable year for the purpose of ascertaining the existence, location, extent, or quality of any deposit of ore or other mineral, and paid or incurred before the beginning of the development state of the mine are deductible at the election of the taxpayer (Section 617(a)).* Were it not for this option, exploration expenditures would be required to be capitalized and recovered through depletion, after production begins. Exploration of a mineral deposit can be very costly and may not result in commercial production for some time. If the taxpayer has income to he offset by the deductions, a mining venture can usually be structured in such a way as to allow the offset of mining losses against the other income. With today's high interest rates, this election can be quite valuable in present value terms. Corporate and noncorporate taxpayers are subject to different restrictions on this tax benefit. Corporations may elect to deduct only 85 percent of eligible exploration expenditures (Section 291(b)). (The Tax Reform Act of 1984 reduced this to 80 percent effective for expenditures after December 31, 1984, in taxable years ending after such date). The remaining 15 percent (20 percent after December 31, 1984) is capitalized and recovered at the same rate as five-year ACRS property (Section 291(b)). Individual taxpayers are not subject to this 85 percent rule; however, any amount deducted in excess of ten-year straightline amortization is a tax preference item for individuals (Section 57(a)(5)). Individuals may avoid the tax preference by electing to capitalize exploration expenditures and amortize them over ten years (Section 58(i)). In order to prevent the taxpayer from, in effect, converting ordinary income into capital gain by selling property that has given rise to exploration expense deductions, the Code requires recapture of such deductions upon the occurrence of certain events (Section 617): 1. Upon disposition of the property, adjusted exploration expenditures are recaptured to the extent of gain realized on the disposition (Section 617(d)). 2. If the property is leased, the lessor is disallowed any depletion deduction until his adjusted exploration expenditures have been recaptured in the form of foregone depletion deductions (Section 617(c)).

Jan 1, 1985

By J. J. Arps

This paper is a study of the effect of temperature on the electrical resistivity of sodium chloride solutions based on the published resistivity and density data in the International Critical Tables. This temperature effect is of considerable importance in quantitative interpretation of electric logs, where it is frequently necessary to correct mud resistivities measured under surface conditions to temperatures existing at the bottom of the bore hole. An empirical approximation formula was developed for this conversion which has proved to be very useful and seems to provide results well within the range of accuracy of the data involved. This approximation formula states: sistivities of sodium chloride solutions at temperatures of t and t degrees Fahrenheit, respectively. INTRODUCTION Research by various investigators during the past 20 years has clarified the physical principles of the phenomena which cause the natural or spontaneous electric potential in rotary drilled bore holes. The basic relationship which is most commonly used reads: in which the SP deflection, as measured from the shale base line, is expressed in millivolts. K is a constant, which appears to vary between 50 and 110; the low value applying to shaly sands, whereas the higher values are more common in carbonate rocks. A good average value for K = 70. for which value there is considerable theoretical justification." In order to calculate the resistivity of the connate water R and to estimate its "equivalent salinity" (as NaCl) from an electric log by means of this SP relationship from a knowledge of the static self potential and of the resistiv- ity of the mud filtrate R it is necessary to first correct the resistivity of the mud filtrate measured under surface conditions to the resistivity of this same mud filtrate in the well bore at a different temperature. In order to make this temperature conversion for the mud filtrate the variation of the electrical resistivity of sodium chloride solutions with temperature is commonly used. Since some discrepancies were found in the charts ordinarily used for this purpose, it was felt desirable to make a new study of this relationship based on the published measurement data. Because of the fundamental nature of these relationships and as an aid to other workers in this field, an attempt has been made in this study to show every step in the calculations. CONDUCTIVITY VS MOL CONCENTRATION The most complete published reference on the temperature relationship of sodium chloride solutions of different concentrations is provided in the International Critical Tables.' The basic measurement data on the electrical conductivity of aqueous sodium chloride solutions, at different temperatures, as given in these tables, are reproduced in Table 1. The electrical conductivity values in this Table 1 are expressed as 10' times the specific conductivity k in ohm-'cm'l per unit of concentration in milligram mols per liter of solution C, or: RESISTIVITY VS MOL CONCENTRATION These conductivity values from Table 1 were first converted to the corresponding electrical resistivity values (R) , expressed in ohm-meters, as is conven-

Jan 1, 1953

By M. H. Waxman, M. Gondouin, H. J. Hill

Streaming-potential experiments were conducted within the Muddy- and Dakota-sandstone interval of a Denver basin well. Analysis of the data shows that, for this case, streaming potentials opposite sands were higher than those opposite shales when the mud was fresh. Streaming potentials opposite shales, however, were of sufficient magniiIlde to be important in SP interpretation. They were linearly dependent upon pressure differential, and they increased with mud filtrate resistivity. The magnitude of streaming potentials opposite sands was influenced by the characteristics of the original mud cake formed at the time of drilling. Use of mud samples taken at the time of logging may not always be satisfactory for determining streaming-potential corrections. Both the streaming and electrochemical potentials were found to be affected by the previous history of the borehole system. Following a change in mud characteristics, several days were required for SP stabilization. This was, in part, due to the mud cake acting as an imperfect shale membrane. INTRODUCTION Laboratory investigations by Wyllie,1 Salisch,2 Moore," Sen Gupta and Bannerjee,0 and Hill and Anderson' have shown that streaming potentials developed across mud cakes deposited on permeable filter beds are of sufficient magnitude to be critically important in SP interpretation. Streaming potentials across shales have been reported by Schenck,' Gondouin and Scala; and Hill and Anderson." The magnitude of the shale streaming potentials obtained by Schenck and by Gondouin et a1 led these authors to conclude that in many cases the shale streaming potential would approximately equal the mud-cake streaming potential. Hill and Anderson, however, obtained somewhat lower magnitudes of shale streaming potential. The field experiment described in the present paper was a cooperative project carried out by the respective operations and research departments of Schlumberger Well Surveying Corp., Shell Development Co. and Shell Oil Co. The primary objective of the experiment was to determine in the borehole the streaming-potential behavior of both shales and mud cakes under conditions approaching, as nearly as possible, those normally encountered in logging practice. METHODS AND EQUIPMENT WELL A Muddy- and Dakota-sandstone vie11 in the Denver basin was chosen for the experiment. Both sandstones were water-bearing and, since reservoir pressures in these sandstones are abnormally low (gradient of approximately 0.25 psi/ft), it was expected that studies of streaming potential could be conducted from low-pressure differentials (approximately 200 psi) to about 27000 psi by bailing mud from the hole, filling up and then applying wellhead pressure. The selected well encountered the Muddy sand-

By Leonard Austin

WHAT Colonel Dwight says regarding the treat-ment of oxidized ores1 holds true also of the silver-lead smelting operations in Utah. The ore sought for was such as would, with appropriate fluxes, yield slag, and "lead bullion," as the lead reduced from the ore and carrying its gold and silver, was called. No matte, and probably little or no speiss, was yielded, and hence there was nothing to roast, either of ore or matte. But, by 1880, when I first took hold in smelting, there was quite a production of matte at the works of the Ger-mania Smelting and Refining Co., Utah, because, by that time, ores containing some pyrite and galena were being smelted. This was due, as at the Grant Works, Denver, to the more attractive price paid for the treatment of such ores. The matte, containing about 5 per cent. copper, was accordingly heap-roasted and returned to the blast furnace for the recovery of its contained metals. By this time there had been built a long-bedded, hand-rabbled reverber-atory roaster with a hearth of about 40 by 10 ft. in size, and in this matte and ore, crushed at the sampling mill, was treated. When, in 1892, I took control of this works, called& now the Germania Lead Works, three other roasters had been added, but the prac-tice of heap-roasting continued. This had the merit of needing no equipment, and of doing good work, because the pieces that were imperfectly roasted went back upon the next roast heap. At this time, when some suitable lump ore was obtainable, I roasted in heaps, in a satisfactory way. By 1892, the Bruckner cylinder roaster had been installed, which, compared with the reverberatory roaster, reduced labor. As such a cylinder revolves, a talus of ore is formed within it and at the same time fresh surfaces are exposed to the air, but the trouble was that the air did not reach to the bottom of the cylinder. This we corrected by placing a steam jet at the fire-box end, to project the air down-ward upon this stagnant ore, thus increasing the speed and completeness of roasting without at the same time increasing dust formation. The firing, if skilfully done, gave a somewhat sintered product, but with certain ores a slight access of heat over the normal would cause accretions to form within the cylinder near the fire end. These could be cut off by running back the fire box and barring off the crusts. It was in 1895 that the Bruckner cylinders at the Arkansas Valley plant, Leadville, were giving unsatis-factory service and I was called in to investigate. The steam jet was put in use as at the Germania Lead Works, but we found that, due to the altitude (10,500 ft.), combustion was feebler than at sea level or even at 4000 to 5000 ft. Later it appears, as Colonel Dwight states, that R. D. Rhodes and Mots sought to increase the air supply by admission through perforated tiles, but the trouble was due to the air itself.

Jan 8, 1922

By D. R. Hay, E. Scala

Electrotransport has been superimposed on the rate-limiling- step in zone refining which is the impurity diffusion through the liquid at the solid/liquid interface. The efficiency of zone refining is increased and relative resistivity ratios (P300°k/P4 2°K) he increased by 50 pel in tungsten for a given number of posses using- the electrotransport field-aided method. The effiect of zotze refining in the presence of an electric field on the relative resistivity ratio is examined as a function of its intensity and polarity. THE effect of electrodiffusion on the effective distribution coefficient of zone refining has been discussed by Pfann and Wagner.' Control of the distribution coefficient in zone refining is of twofold interest. A distribution coefficient of unity can be increased or decreased, making possible the transfer of some previously inseparable solutes. The general efficiency of zone refining can also be increased. In the conventional zone-refining process impurities are removed by their retention in the molten zone and subsequent deposition at the end of the rod after a complete passage of the zone. In higher-melting-point systems a second mechanism may also operate, the volatilization of impurities from the molten zone. It has been suggested by schadler2 that, in refractory metals, vacuum distillation plays the predominant role in purification. In Koo's results,3 the resistivity ratio decreased beyond a zone-refined length of 6 in. from the starting end, indicating that some purification does in fact occur by true zone-refining action. Hay and scala4 showed that the degree of purity as measured by the relative resistivity ratio method depends on the square root of time in the molten zone (number of passes) and thus appears to be limited by diffusion in the boundary layer at the solidifying interface assuming good mixing in the body of the molten zone where a linear rate would prevail. The final concentration of impurities in electron-beam floating-zone purification depends very much on the operating conditions and results obtained by various investigators2,3,5 are difficult to correlate. The diameter of the starting material, operating vacuum, and rate of traverse are among the factors to be considered. There are, nevertheless, some general observations to be obtained from the literature. Lawley5 reviewed the literature up to 1962 and concluded that the major contaminants generally remaining in tungsten after electron-beam zone refining are molybdenum and carbon. Molybdenum due to its high melting point and distribution coefficient of nearly unity would be expected to be difficult to remove by either volatilization or zone refining. Carbon is not only a common contaminant in vacuum systems, but is also very difficult to remove by conventional vacuum melting. even with vacuums of 10-7 mm Hg. For each of those impurities removed by zone refining the equation of Pfann and Wagner may be applied: It relates the effective distribution coefficient k to a superimposed driving force which accelerates the solute away from the interface with a terminal velocity L" and to the more conventional zone-refining parameters; v = rate of traverse, t = thickness of the diffusion layer at the solidifying interface, D = diffusivity of the solute in the molten zone, and ko = equilibrium distribution coefficient of the impurity.

Jan 1, 1965

THE discussion of this topic at the Open-hearth Conference at Detroit on Nov. 3, 1927, was opened by statements of the general principles involved, made by manufacturers of molds. Because of their general interest they are printed below. WILLIAM HAIL RAMAGE,* Hubbard, Ohio.-I did not come prepared to read a paper, thinking. the most I would be called upon to do would be to make a few, remarks by way of discussion. A number of our friends have pre-viously asked questions. similar to this which really does not permit a direct "yes" or "no" answer. If I may he pardoned for so doing, I believe it advisable to discuss rather what we consider the principal factors which in-fluence mold life. I think possibly a little undue weight has been given to the subject of the analysis of the metal. For the last eight years we have spent a lot of time, effort, and money investigating this very problem from a chemical, physical and microscopic standpoint. We have had the benefit of complete records and history of over 100,000 molds in service at a variety of plants and over long periods of time. Obviously, I cannot be so specific that I should divulge information that is really a trade secret. In our opinion the principal factors influencing mold life are: (1) design of the mold; (2) process of manu-facture, including workmanship; (3) care in the steel plant or what might be termed "the use or abuse" in the steel plant; (4) the analysis of the iron and the physical con-dition of it. Under normal conditions these factors are of importance in the order named, although in specific cases they might be rearranged in any order you choose. For instance, the best mold made can be destroyed in one or two pours by subjecting it to certain conditions which are occasion-ally met in steel plant practice. Obviously, in that case, nothing else matters but that one item. On the other hand, I have seen molds made of such a terrible design that it was a foregone conclusion it would have to be broken after the second pour of the ingot to get it out. In that case, nothing but design mattered. As to the effect of process of manufacture, let me cite a case. Some years ago there were two batches of molds sent to a certain company. They were the same sized molds, used under the same conditions and in the same kind of service. There were, 20 molds in each batch. The second batch sent gave ten times the life of the first batch. It is true that the design was changed a little, but not very much, and it was not. a bad mold to begin with. It is possible that the iron may have been better in the second consignment but not very much. In my opinion, it is con-servative to say that of the 900 per cent improvement in life, 5 per cent was probably due to better iron, 25 per cent to better design and the remaining 870 per cent to process of manufacture and workmanship.

Jan 2, 1928

By B. C. Craft, Murray F. Hawkins, John R. Rayne

A reservoir mechanism of sulfur recovery by the Frasch process is presented. Improving the economic, of recovery appears to be largely a well, rather than a reservoir problem. A most important factor is the limitation of the lateral extraction of .sulfur about the wells due to the almost vertical .flow of the injected hot water. Model studies are described which confirin the mechanism of sulfur recovery by presently used methods. Studies on a five-spot system indicate improved econo171ics regarding recovery, recovery rate, therinal efficiency, and well spacing. INTRODUCTION Sulfur mining by the Frasch process is one of the most important methods of sulfur production. Developed by Herman Frasch in 1894, it enjoyed a rapid growth and presently supplies 40 per cent of the world's sulfur and about 80 per cent of the U. S. sulfur." The Frasch process of mining the underground native sulfur deposits involves melting the sulfur in place by introducing super-heated water into the sulfur bearing formations, and producing the sulfur as a liquid. Many problems are encountered in mining these native sulfur deposits, and sulfur production depends chiefly upon the nature of the sulfur deposit and the underground thermal efficiency of the heat transfer system. THE RECOVERY MECHANISM Sulfur is typically found in salt dome cap rock as crystal aggregates occurring within the cavities, seams, and pores of limestone and gypsum formations.' Sulfur-bearing limestone is typically cavernous, vugular, and fractured. Porosity averages about 20 per cent and sulfur saturation averages approximately 25 per cent by weight.1,15 Vhe sulfur bearing formations are very heterogeneous in nature and physical characteristics vary widely within small distances. Total cap rock thickness may vary from 50 to more than 1,000 ft, and net productive thicknesses from a few feet to a few hundred feet. In most cases the upper portion of the limestone formation is barren of sulfur, varying from 5 to 200 ft in thickness.1,15,33 The immediately overlying sediments and the underlying dense anhydrite formation provide permeability barriers to the flow of water from the cap rock section.'" Sulfur wells are drilled with conventional oilfield drilling rigs. Fig. 1 illustrates the casing program of a completed sulfur well. The cap rock sections are drilled with core bits and continuous core logs are recorded. After coring, the cap rock section is underreamed to a diameter of 9 7/8 in. The bottom of the 8-in. casing is welded closed and rests on the bottom of the drill hole, which extends through the cap rock to a few feet above the bottom of the sulfur-bearing formation. The 8-in. pipe contains 5 ft of 3/4-in. perforations on 6-in. centers and 15 ft of 1-in. perforations on 1-ft centers. The 20-ft perforated section is set opposite the lower 20 ft of the sulfur-bearing formation. The 4-in. sulfur pipe is set inside the 8-in. water line on a seat ring at the top of the 5-ft section of 3/4-in. perforations. The mining water, heated to about 330°F under a pressure of 250 psi, is forced down the annulus between the 8-in. and 441-1. pipes and through the 1-in. perforations to the sulfur-bearing formation. Compressed air, at 400 psi pressure, is supplied through a 1-in. air line near the bottom of the well to provide air-lift of the liquid

Jan 1, 1957

By Lawrence H. Van Vlack

The energy of the y-iron grain boundary was determined to be 850 ergs per cm2 at 1105°C. The a/a and the a/y boundaries possess somewhat less energy. The microstructures of several iron alloys are discussed in terms of the interfacial energy relationships. THE dependence of the shape of liquid interfaces upon their energies has been studied for some time.1"3 Recently, Smith' concluded that many of the microstructures observed in metals may be attributed to the energies of the interfaces between the grains and phases. While the energies of liquid surfaces have been measured by numerous different methods: only two attempts have been made to determine experimentally the energy of surfaces involving crystalline solids. Udin, Shaler, and Wulff8 used a procedure introduced by Berggren7 to measure the surface tension of solid copper. It consisted of determining the load required on a thin copper wire so that the surface tension was counteracted, and no net strain resulted. Bailey and Watkins8 sed a different technique and were able to determine both the surface tension of copper and the tension of the copper grain boundary. They measured the contact angle which liquid lead makes against a copper surface. They then calculated the above energies from the surface energy of liquid lead by using the Pb vs. Cu/CuY dihedral angle and the surface groove angle formed during thermal etching. They obtained a value of 1800 dynes per cm for the surface tension of clean copper and approximately 640 dynes per cm for the tension of copper grain boundaries. The former value was somewhat higher than Udin's value of 1500 dynes per cm. This paper includes a determination of the energy of the y-iron grain boundary. In addition, the micro-structural relationships of several other metallic and nonmetallic phases with iron were examined and an attempt was made to interpret the observed structures in terms of interfacial energy relationships. Theoretical Considerations In a three-phase material containing a solid and two liquids, there may be two solid/liquid interfaces, one liquid/liquid interface and one inter- granular interface. Liquid/liquid interfacial energies can be measured directly. Therefore, by determining the energy of such an interface and by measuring the required interfacial angles: the energies of the interfaces involving solids may be obtained.10 They may be shown schematically as in Fig. 1. The above procedure requires the following assumptions: 1—The interfacial energies are, in general, unaffected by boundary orientation, and 2— the shapes of the interfaces are unaltered between annealing and sectioning for microscopic examination. The first assumption is good to a first approximation as shown by Dunn and Lionetti11 except for a few critically orientated boundaries. Two conditions may alter the shape of a boundary upon cooling: 1—Precipitation of dissolved material upon one side of the interface, and 2—a change in volume during the transition from one phase modification to another. The former must be detected by microscopic observation. The latter may become appreciable in systems containing an interface between two liquids which solidify after annealing. However, possible movement of the two-liquid interface may be checked in the system diagrammed in Fig. 1 by measuring 8, for example, and comparing it with its value as calculated from the other interfacial angles by: tan8, C11 05 COS- o- + cos 8, cos- The choice of a suitable pair of liquids is limited by several factors. The relative values of the several

Jan 1, 1952

By R. C. Canby

JUDGE GRANT, in a delightful satire of his, says: "Boston is a state of mind." I think that this same statement might well be made of the metallurgy of lead. I was particularly impressed with this when about thirteen or fourteen years ago I prepared a paper on "Development of the American Water- jacket Lead Blast Furnace." Dividing the time, as I did into ten-year periods, from the commencement of lead smelting at Eureka, Nev. (1870), and showing the tendency for each of the five decades it was evident that the progress had been through a succession of states of mind from the rule of thumb through the ultra scientific, or from what I might call the slag type period up to the present highly developed art. Conservatism has been characteristic of the metallurgist. This may have been most natural, especially with the lead metallurgist, the development of whose art was so entirely in the custom smelting plant, where the metal contents of his ores were paid for in cash and therefore excessive metallurgical losses could mean nothing short of financial bankruptcy. The metallurgist himself was held to a personal account, in these smelting plants. It was the metallurgist who was accountable. In the concentrating plants, if undue losses occurred remodelling of the plant was discussed, but if there were excessive metallurgical losses in the custom smelting plant, a new metallurgist was considered as the remedy. For this reason the tendency was to adhere to recognized practice and to be wary of unusual methods, using the word unusual in the sense in which it is used in Article VIII of the Constitution of the United States, as to punishments and modes of death. This conservatism of the metallurgist was reflected as other branches of metallurgy were developed. We have heard of the wonderful development of flotation, but it had to be introduced over the dead metallurgical bodies of its opponents.

Jan 1, 1926

By W. Philippoff, Donald E. Cadwell, S. R. B. Cooke

THE importance of contact angles in flotation has long been recognized, but little has been done to get quantitative relationships between the surface coverage of the mineral by the reagent, the length of the hydrocarbon chain, and the contact angle. It is well known that for a complete monolayer on the surface of a mineral the contact angle 8 is determined only by the reagent1 and principally by the chain length of the hydrocarbon radical. Although for flotation the monolayer usually is regarded as being complete, early experiments of Wark and Cox&apos; showed that at very small concentrations of potassium ethyl xanthate the contact angle on galena changed in a continuous way from 0&apos; to the equilibrium value of 60". Further, Gaudin and Vincenta showed a similar continuity using heptylic acid and sphalerite. This shows that with probably incomplete monolayers, 0 varies with the degree of surface coverage. At the time these experiments were made it was impossible to measure the actual amount of surface coverage, especially since the decrease of the collector concentration in the liquor could be influenced by chemical side reactions. Through the use of the radioactive tracer method for the measurement of the amount of collector adsorbed on the surface of the mineral, Gaudin and Bloecher&apos; were able to determine accurately the actual surface coverage of dodecylamine acetate on quartz, but they did not measure any contact angles. It is believed that the relationship between the surface coverage and the contact angle is extremely important in flotation, especially as Gaudin and Bloecher showed that a 95 pct recovery is possible with a coverage of only 5 pct. Theoretical Considerations The work of adhesion W is the energy bound (in ergs per sq cm) when an interface is formed. It is determined by the difference of the free surface energies (surface tensions) of the respective phases 7j and yZ before contact and the interfacial free surface energy y, after contact. The definition of the contact angle permits the elimination of the unknown surface energy of the solid and hence the calculation of W from the surface tension of the liquid y and the contact angle 8: W = y (1 + COS0) [1] Consider a surface consisting of two components, identified as 2 and 3, 1 being the liquid. The amount of 2 in the composite surface is x, where 0 < x < 1. The respective contact angles with 1 and air are 8, and 8.. The total work of adhesion of such a surface is the sum of the values of the components multiplied by their respective areas. A formal relation can be written: Wm = x-W2+ (l-x)-W, [2] in which W, is the work of adhesion of the composite surface. Eq 1 can be introduced into Wt and Wa, but in the case of W, some discussion is needed. If the two components are segregated, each component forming an integral part of the composite surface there is no physical meaning for a contact angle 8m calculated from W,, by using eq 1. If, on the other hand, the area of each patch of the components is small in comparison with, say, the diameter of the bubble used in measuring, it could be expected that 0m would have a physical significance, because of the action of the surface tension of the liquid-gas interface tending to smooth out sharp corners. How small these patches would have to be is difficult to predict, but by using composite surfaces with microscopically

Jan 1, 1953

By R. Simon, L. Yarborough

This paper presents a correlation for predicting the critical pressures of gas-solvent-reservoir oil systems of the type encountered in gas and solvent injection processes. Experimental data from 14 systems were used to develop the correlation which expresses critical pressure as a function of composition, C7+ mol weight, and C7+ characterization factor. Critical pressures predicted by the correlation for the 14 gas-solvent-reservoir oil systems have an average deviation of 2.8 per cent of the experimental values. The correlation war used to study a wide variety of other hydrocarbon mixtures reported in the literature whose critical conditions are in the range of interest in oil recovery work (100 to 280F and 2,000 to 6,000 psia). Critical pressures predicted by the correlation had an average deviation, expressed as per cent of experimental value, of 5 per cent for 20 miscellaneous mixtures from the literature, and 6.4 per cent for I7 methane-butane-decane mixtures reported by Sage and Lucey. INTRODUCTION Predicting critical points of hydrocarbon mixtures is an important part of phase behavior calculations. If the critical point can be predicted for a specific mixture, the separation between the bubble-point and dew-point regions will be defined, and physical properties of the mixture can be calculated by using the principle of corresponding states. Numerous correlations for predicting critical points of hydrocarbon mixtures have been published. Six of these correlationsl-8 were for light hydrocarbons, and two correlations7,8 ere for high boiling-point petroleum distillates. Organick9 And Eilerts" presented correlations which combined the published data from both light and heavy mixtures, and these correlations became the only available methods for predicting critical pressures for wide boiling range mixtures. In the course of the authors&apos; work on secondary recovery by gas and solvent injection, experimental data were obtained for 14 mixtures of dry gas, ethane-propane-butane solvents, and various reservoir oils. The critical pressures and critical temperatures of these gas-solvent-reservoir oil systems were in the range of 1,900 to 4,800 psia and 180 to 265F. The critical pressures predicted for the 14 mixtures by the correlations of Organick and Eilerts had an average deviation from the measured values of about 13 per cent. The authors felt that it was necessary to develop a better correlation for engineering calculations and the resultant correlation, which is presented on Figs. 1 and 2, predicts the critical pressures of the 14 mixtures with an average deviation of 2.8 per cent. The validity of the correlation was tested by applying the correlation to other hydrocarbon mixtures reported in the literature. This subject is discussed later in the paper. The authors feel that there is also a need for an improved critical temperature correlation for gas-solvent-reservoir oil systems. However, developing a critical temperature correlation is a significant study in itself and is not included in this paper. EXPERIMENTAL DATA The compositions and critical points obtained by the authors for 14 gas-solvent-reservoir oil mixtures are shown on Table 1. The methane concentrations in these mixtures varied from 20 to 63 mol per cent. The intermediate hydrocarbon group, consisting of ethane, propane, and butane, varied from 20 to 64 mol per cent, and the concentration of the C,, fraction from 10 to 20 mol per cent. The physical properties of the C,, fraction covered the range from light, paraffinic, nonasphaltic (Mixtures 5, 6, 7, 8, 9 and 10) to heavy, aromatic, and asphaltic (Mixtures 13 and 14).

By S. R. B. Cooke, W. Philippoff, Donald E. Cadwell

THE importance of contact angles in flotation has long been recognized, but little has been done to get quantitative relationships between the surface coverage of the mineral by the reagent, the length of the hydrocarbon chain, and the contact angle. It is well known that for a complete monolayer on the surface of a mineral the contact angle 8 is determined only by the reagent1 and principally by the chain length of the hydrocarbon radical. Although for flotation the monolayer usually is regarded as being complete, early experiments of Wark and Cox&apos; showed that at very small concentrations of potassium ethyl xanthate the contact angle on galena changed in a continuous way from 0&apos; to the equilibrium value of 60". Further, Gaudin and Vincenta showed a similar continuity using heptylic acid and sphalerite. This shows that with probably incomplete monolayers, 0 varies with the degree of surface coverage. At the time these experiments were made it was impossible to measure the actual amount of surface coverage, especially since the decrease of the collector concentration in the liquor could be influenced by chemical side reactions. Through the use of the radioactive tracer method for the measurement of the amount of collector adsorbed on the surface of the mineral, Gaudin and Bloecher&apos; were able to determine accurately the actual surface coverage of dodecylamine acetate on quartz, but they did not measure any contact angles. It is believed that the relationship between the surface coverage and the contact angle is extremely important in flotation, especially as Gaudin and Bloecher showed that a 95 pct recovery is possible with a coverage of only 5 pct. Theoretical Considerations The work of adhesion W is the energy bound (in ergs per sq cm) when an interface is formed. It is determined by the difference of the free surface energies (surface tensions) of the respective phases 7j and yZ before contact and the interfacial free surface energy y, after contact. The definition of the contact angle permits the elimination of the unknown surface energy of the solid and hence the calculation of W from the surface tension of the liquid y and the contact angle 8: W = y (1 + COS0) [1] Consider a surface consisting of two components, identified as 2 and 3, 1 being the liquid. The amount of 2 in the composite surface is x, where 0 < x < 1. The respective contact angles with 1 and air are 8, and 8.. The total work of adhesion of such a surface is the sum of the values of the components multiplied by their respective areas. A formal relation can be written: Wm = x-W2+ (l-x)-W, [2] in which W, is the work of adhesion of the composite surface. Eq 1 can be introduced into Wt and Wa, but in the case of W, some discussion is needed. If the two components are segregated, each component forming an integral part of the composite surface there is no physical meaning for a contact angle 8m calculated from W,, by using eq 1. If, on the other hand, the area of each patch of the components is small in comparison with, say, the diameter of the bubble used in measuring, it could be expected that 0m would have a physical significance, because of the action of the surface tension of the liquid-gas interface tending to smooth out sharp corners. How small these patches would have to be is difficult to predict, but by using composite surfaces with microscopically

Jan 1, 1953

Jan 1, 1925

By Robert S. Archer, L. W. Kempf

It is now well known that the structure of aluminum-silicon alloys can be refined in a rather remarkable manner, with consequent improvement of physical properties, by certain treatments applied to the molten metal shortly before casting. The differences between the treated and the untreated alloys are so marked that special terms are used to distinguish them, the untreated alloys being referred to as "normal" and the treated alloys as "modified." The first practical method of accomplishing this result was that of A. Pacz,1 which consists in treating the molten metal with a salt flux of which the active ingredient is sodium fluoride. The result can also be brought about, and in a more economical manner, by the addition of small quantities of metallic sodium (or potassium) to the molten alloy shortly before casting.2 The action of the Pacz flux evidently consists essentially in the production of free sodium by the reaction of sodium fluoride with aluminum. The changing of a normal alloy to a modified alloy is referred to as "modification" and any process for accomplishing this result is a "modifying" process. Modified aluminum-silicon alloys were introduced several years ago, and it has been demonstrated both in the laboratory and in commercial practice that it is no simple matter to produce castings having the maximum or nearly the maximum properties which under favorable circumstances can be obtained. The alloys are rather sensitive to small changes in chemical composition, and the modifying process must be carried out in a very particular manner to obtain the best results. Extensive experimental work has been carried out in the laboratories of the Aluminum Co. of America with the object of determining the conditions that must be observed to make these alloys of the greatest possible value. It was necessary to learn how to control the modifying process

Jan 1, 1926

By S. W. Miller

MOST of the steel welding done at the present time is in material containing not over 0.3 per cent. carbon, and the tests here described were in similar material. These tests are not as yet completed but it is hoped that more results and more reasons for the conclusions may be presented at the meeting in February. From the time the author found the peculiar structure in electric welds referred to in a previous paper,1 that is, needles or plates in the grains and similar material, in larger spots, at the grain boundaries, he has felt that these plates which may be iron nitride and probably contain some carbon, were at least partly responsible for the brittleness of electric welds. He has found but few traces of similar lines in oxyacetylene welds until the last 2 mo., when he has found them in large numbers under certain conditions. In the top of these welds, they are quite numerous. In the body of heavy oxyacetylene welds, they appear at times, but not nearly to the extent that they do in electric welds; the author has never seen them in the body of welds in material less than ;3/4 in. (19 mm.) thick. They are shown in Fig. 82. The reason they were not noticed before is undoubtedly due to the fact that in making tests of welded pieces the weld was always ground off level with the plate, and as this structure only appears in the top ;1/16 in. (1.5 mm.) of the weld, they were removed by the grinding or machining; also, welds ¾ in. thick had not been examined. It did not appear, in making bending tests, that this structure had much influence on the strength of oxyacetylene welds; while electric welds are noticeably brittle. Further, oxyacetylene welds made with certain special materials were exceedingly brittle even after the tops of the welds were removed; this was true in cases where there was no sign of the plates whatever and where the welds were remarkably free from oxide and the other usual defects. It appeared, therefore, that this brittleness did not depend on any variable that had been noticed so far, and it was

Jan 2, 1919