Search Documents

By F. R. Hensel

Up to the present time few attempts have been made to produce hard nonmagnetic materials by heat treatment of austenitic steels. The usual result has been to cause them to pass into the martensitic stage, thus destroying to a great extent the typical austenitic properties, since this involves a transition of a portion of the iron from a face-centered to a body-centered type of atomic arrangement. High-strength nonmagnetic materials such as might be provided by properly hardening austenite are required in the electrical industry for different machine parts. In Europe nonmagnetic retainer rings for restraining the end-turns of the rotor windings in turbo-alternators have been developed as a special application of high-strength austenite. In testing1 a 28,000-kva. three-phase Siemens turbo generator running at 3000 r.p.m. at full load current, the losses in the short-circuit test were 450 kw. for the magnetic ring and 286 kw. for the nonmagnetic, and the difference should be attributable to the magnetic ring. The differences in temperatures during the same test are given in Table 1 and these show the advantage of a nonmagnetic over a magnetic retainer ring.

Jan 1, 1931

By Larsen. Edward P.

The principle of "bed blending" in the agglomeration of materials is about 56 years old, but de- spite all education via technical papers, operating reports and results from functioning installations, the concepts of blending are still somewhat vague. Confusion exists between "mixing", "blending," and the basic role of each. The terms "blending" and mixing" are often used interchangeably, yet they describe two different processes. As properly understood and applied, a blend is a combination of different varieties of material which produces a desired quality, or the mingling of different elements to form a harmonious whole. In other words, blending is a process of combining granular materials by mechanical means, wherein the final product, or a portion thereof, must contain an exact proportional amount of every one of the several different materials which contributed to the mass and wherein all particles are so thoroughly intermingled with each other as to have lost their individual identities and become a part of the whole so that when a portion of the blend is taken at any time it will be substantially identical, chemically and physically, to any other portion taken throughout.

Jan 1, 1962

By Casper A. Nelson, Wendell M. Whitecotton

A WIDE variety of lead ore is treated by the Midvale Smelter, for it is a custom plant not only treating Company lead concentrate and direct-smelting ores but also custom ores and concentrates, principally from Utah, Idaho, and Nevada, with lesser amounts from Arizona, California, Colorado, Montana, Oregon, and Washington. The principal operating departments of the plant are weighing and sampling, Wedge roaster, D&L sintering, blast furnace and drossing, and baghouse. The lead bullion produced is shipped to a subsidiary, the U.S.S. Lead Refinery, Inc., at East Chicago, while the by-products, such as matte and speiss, are shipped to other smelters or re-treated at the plant.

Jan 1, 1948

By T. A. Rickard

The interior of West Australia is an arid table-land, elevated 1400 feet above the sea. This plateau is flanked to the south by the Tertiary limestones which fringe the Great Australian Bight. It is bordered northward by the Carboniferous beds of the Fitzroy river and westward by the granite of the Darling hills, while to the cast this wide area, about 900 miles square, slopes downward imperceptibly into an undulating plain of sand, which stretches with dismal persistence across the boundary of South Australia. The waters of the ocean receded from this tract of land long ago; it is probably the oldest landsurface on the globe, and represents the basal wreck of a much larger continent. Fig. 1 is a map of this region. The Coolgardie and Kalgoorlie gold-fields are situated in the southwestern part of the region. The rock-formation consists of granite penetrated by diorites and andesites. The latter are occasionally associated with tuff's, which have been readily mistaken for sedimentaries. There are no fossil-bearing rocks, such as would afford a datum-line from which to measure the relative geological age of the prevailing formation. On the extreme edges of the mining territory there are, it is true, remnants of sand-rock which are considered identical with the " Desert Sandstone " of Queensland, determined by Daintree to be of Mesozoic age. But even this formation has evidently been laid down so long subsequent to the underlying rocks that it serves merely to emphasize their much greater antiquity. In their characteristics and in their relations to each other, the granite and the diorite of the Coolgardie region appear to me much to resemble the Laurentian granite and the Huronian

Jan 1, 1899

By Donald B. Gillies

THE great source of iron ore for the furnaces of this country has been the Lake Superior district. Ore was first discovered there in 1844, and the first shipments made via the Great Lakes in 1852 to a furnace at New Castle, Pa. The stream of ore from that region increased slowly to exceed a million tons in 1873, and did not reach 10 million tons until 1895. By 1901 it exceeded 20 million tons, and in 1907 over 40 million tons. Total Lake Superior output through 1948 was about 2500 million long tons. Outside the Lake Superior district are the Southern district, including mainly Alabama, Georgia, Missouri, and Texas; the Eastern district of New York, New Jersey, and Pennsylvania; the Western district embracing Wyoming, Utah, and California.

Jan 1, 1949

By Clyde E. Williams

THROUGHOUT its history the American iron and steel industry has constantly striven to improve the quality and reduce the cost of its products. No one needs to be told how well it has succeeded. Its success in making steel products at such a low cost has been achieved mainly through large-scale production. While costs have gone down as the rate of production and the degree of mechanization increased, quality of product has been actually improved. Thus high-tonnage records are important only in the light of high quality of the steel. Quality is the watchword! Continual improvement in quality has come as a result of research, not only in the laboratory but in the large commercial units in the plant. In fact, so many operations of the industry are on such a huge scale that experimental work must be done under commercial operating conditions so every progressive steel plant is a research laboratory.

Jan 1, 1938

By C. H. Mathewson, E. M. Thalheimer

In planning the present experiments, we have made a particular effort to secure that adjustment of working conditions which would render the forthcoming tests most serviceable by way of indicating the comparative properties of the three different commercial grades of copper used. More specifically, we have endeavored to obtain certain definite information with respect to the relative behavior under test of ordinary electrolytic copper and furnace-refined lake copper containing (a) a moderate percentage of arsenic and (b) a rather large percentage of arsenic, in addition to the usual content of silver and other impurities. These comparisons were made systematic and comprehensive by testing throughout a series of (eight) reductions running from 0 to 70 per cent. in the case of cold-rolled metal, and throughout a series of (15) temperatures running from 100' C. to 1,000" C. in the case of annealed metal. In other words, a survey of properties similar to that made by Grard,' in the case of electrolytic copper, was here repeated (with modifications) and extended to two other commercial varieties of copper. The great importance of copper both as a material of construction and as the base of our most important alloys (aside from steel) has led to innumerable investigations of its properties, particularly in commercial forms. Naturally, the merits of furnace-refined lake coppers us. those of the very pure electrolytic product have furnished the subject of much experimental work and animated discussion, wherein the effect of arsenic has by no means been overlooked. In the literature of the past 10 years,

Jan 1, 1917

By Lawrence Wright

ON the steep slopes of the Kootenays, 15 to 20 miles south of Nelson, B. C., are a number of ore occurrences (Fig. 1). One that has many features of mining and geological interest is the Ymir Yankee Girl Gold Mines Limited. Discovery of this property was made in 1899 at an outcrop on the hillside, some 2500 ft. above the village of Ymir. This proved to be a branch vein 20 ft. long leading to two main veins, the Yankee Girl and the Spur (Fig. 5). The ore pattern as now delimited shows a remarkable increase in ore area with depth below the outcrop. This recent development is of interest particularly in view of the fact that the property was nearly con-demned, professionally. Another interesting feature, which has a bearing upon its history, is the persistent excess of tonnage produced from period to period over visible reserves. This is not ascribed to lagging mine development, but to detailed vein characteristics, which we will endeavor to make clear by giving a description of the veins and their surroundings.

Jan 1, 1938

By AIME AIME

MEXICO embraces one of the great metal and petroleum producing provinces of the world. In this respect its history dates back to the overthrow of the Aztec empire by a Spanish force under Hernando Cortes between 1519 and 1.521. Even before then, its richness in silver and other minerals was not unknown. But it was a treasure house for the Spanish conquerors until the country became independent in 1821. It has been computed that in the 400 years following 1521, Mexico yielded 1.55,000 metric tons of silver, worth $3,000,000,000, two-thirds of the entire world production. In 1935 the country accounted for 36 per cent of the world's silver output, 14 per cent of its antimony (in 1934), 13 per cent of its lead, 3 per cent of its zinc and copper, and 21/2 per cent of its petroleum. Contrary to the impression of some, its gold output is now comparatively small, though important in the past. Its oil, as well, formerly hulked much larger than now, in 1921 being one-fourth of the world output.

Jan 1, 1936

By E. L. Jr. Spain

THE deposits described in this paper occur over much of Wayne County and in the southeast portion of Hardin County, Tennessee, and in the northeast and northwest portions of Mississippi and Alabama respec-tively. The presence of tripoli in this region has been known for some time and descriptions of various occurrences in Tennessee have been made by Jewell1 and Miser2, while Hilgard3, Lowe4 and Logan5 have treated the deposits that occur in the adjacent portions of Alabama and Mississippi, but there has not been a general survey of the entire field summarizing completely the geology of the deposits with respect to their origin and stratigraphic relationships. During 1934, while engaged in surveys of mineral resources through this region for the Tennessee Valley Authority, the writer collected data with this in mind, and has assembled them in this report. He is indebted to H. S. Rankin and N. A. Rose, of the Tennessee Valley Authority Geology Division, for field assistance.

Jan 1, 1936

By Ralph H. Sweetser

IN the recent world-wide deflation of commodity prices the coal industry, including both anthracite and bituminous coal, had reached a level where the actual delivered market prices received by the operators were usually less than the cost of production. Many steel companies and public utilities, operating their own "captive" mines, could have bought coal during the past three years for less money than the true cost of coal produced at their own properties. Competition within the coal industry itself was cruel to the point of profitless operation, and the competition of other forms of fuel was bearing heavily on the coal producers. They were thus forced into methods of production and utilization that they had hitherto ignored; there had been almost complete absence of any appreciation (by the bituminous operators especially) of the necessity of real research work in finding better methods of preparing coal for specific uses, and in finding new and profitable uses for different kinds and grades of coal.

Jan 1, 1933

By MALCOLM FRASER

I was delighted to be invited to be patron of this Joint Conference, but the challenging task you have set yourselves, and your speakers' depth of expertise, deny anyone, even the patron, the opportunity to be patronizing. Australia's history has been inextricably linked with the fortunes of our great mining industry. That link will remain. Just as the gold rushes of the last century, and the discoveries at Kalgoorlie and Broken Hill changed the lives of generations, so the more recent development activity in iron ore, bauxite, nickel, coal, and uranium are having a significant impact on the lives of Australians today. The minerals industry has contributed to Australia's jobs and prosperity. Mining is not free of problems, but so long as safeguards are strong and appropriate the net benefits the mining industry brings Australia will continue to be enormous. We rely on our mining industry to find, prove, develop and sell our minerals profitably, and my Government is committed to maintaining a healthy mining industry. In the past year there have been positive signs of a resurgence in exploration and development. The North-West Shelf ventures are spending $50 million on a feasibility study to work out the extent of future investment in that project; exploration expenditure for minerals other than petroleum increased by 34 per cent in 1976-77 to $134 million; petroleum exploration increased dramatically last year almost doubling to $94 million-this year it is projected to reach $125 million.

Jan 1, 1978

By C. K. Leith

THE interdependence of nations in regard to mineral supplies has grown apace with the expanded needs of industry, with depletion of reserves, and with advances in technology. This increased mutual dependence raises many questions of foreign economic policy of special importance in our postwar planning. Realization of the urgent need for the development of a general mineral policy broadly based on national requirements led to discussions of the problem between officials of the Department of State and myself, as a result of which it was suggested that I make an informal and unofficial canvass of the views of mineral specialists of the country on foreign mineral policy.

Jan 1, 1946

By P. R. Sahm, T. V. Pruss

Mixtures of fine GaSb and Gds as well as preal-loyed GaSbl,As, powders were hot-pressed at 690°C and 25,000 psi. Dense alloys with compositional gradients of less than 5 pct were obtained from mixtures containing about 20 mol pct GaAs. For x < 0.2, there were increasing compositional gradients, and for x > 0.2 a GaAs-rich second phase appeared in the microstructure. Densification as well as alloying wlechanisms were enhanced by dissociation and, possibly, oxidation reactions of the powders. Densification of coarse prealloyed material, however, primarily depended on plastic flow phenomena and required temperatures just below solidus and pressures of 50,000 psi Thermal and electrical properties were measured. Although in no case was the figure of merit of melt growth materials approached closer than to within 25 pct, the better overall thermoelectric properties were found in coarse-grained, prealloyed materzals which had been compacted to near theoretical density and where grain regrowth had been induced. Similar results are believed to hold in other binary 111-V compound systems if processed under similar conditions. The densification of unalloyed GaSb powders during pressure sintering (= hot pressing) was shown to depend strongly on powder particle size.&apos; Fine powders displayed a "liquid skin effect" that enhanced compaction through the presence of liquid gallium, whereas coarse powders compacted predominantly by plastic flow. The liquid skin effect, in particular, appeared attractive for alloying GaSb with other, higher-melting, III-V compounds, and to densify these in a one-step operation. This is of special interest in the case of III-V compound alloys as the conventional techniques of melt growth or long-time annealing of powders2 is very time-consuming, especially in cases where a large separation of liquidus and solidus can be expected, such as in GaSbl alloys.2 It was felt that experimentation with this system, a particularly unfavorable example, would allow us to extrapolate to several other, more favorable, cases. Uses of Ill-V alloys are most evident in thermoelectric energy conversion devices.&apos; For this reason certain thermal and electrical properties were measured and compared to those of melt-grown material and to hot-pressed prealloyed powders. EXPERIMENTAL PROCEDURE The pressure-sintering apparatus has been previously described.&apos; Using this equipment, both powder mixtures of GaSb with GaAs and prealloyed GaSbl-,As, powders were hot-pressed. The mixtures were pre- pared from cast GaSb and melt-grown GaAs. The prealloyed material was obtained from stoichiometric melts, initially heated to 1200°C in an evacuated quartz ampoule, and then annealed in the solidus-liquidus interval. A typical annealing cycle consisted of a heating to 850°C (1 hr), extended successive annealing at 750°C (65 hr), and slow stepwise cooling (25 hr) to below solidus. The GaSb, GaAs, and GaSbl-,As, materials were ground in a vibrational mill to particle sizes below 500 . A jet mill reduced these further where necessary. Fine powders were analyzed by Coulter counting for their size distribution. Average sizes by volume were calculated from the data. Mixing of the powders, where necessary, was carried out through rapid vibrational motion. The hot-pressing operation consisted of a degassing period of 15 hr, in most cases at 690°C, followed by several hours of compression, normally 25,000 psi at 690°C for powder mixtures and 50,000 psi at 710°C for prealloyed powders. The chemical compositions were confirmed by X-ray fluorescence analysis. To estimate the degree of solid solution achieved, lattice parameters were determined and interpreted according to Vegard&apos;s rule. In addition, optical microscopy helped to correlate the relative amounts of the phases present as well as the degree of porosity to the measured density. To reveal grain boundaries, polished surfaces were etched4 with H 2 O:H 2 O:HCl = 2:l:l. In several cases microscopic concentration gradients were monitored by electron-probe analysis-. RESULTS AND DISCUSSION Alloying and Densification of GaSn-GaAs Powder Mixtures. After preliminary experiments showed that no appreciable alloying took place in mixtures of coarse GaSb (22.5 p) and fine GaAs (2.5 p) powders, hot pressing of mixtures was confined to fine powders only (3.1 and 2.4 p, respectively). Alloying and densification apparently occurred simultaneously with a grain regrowth mechanism which depended on the presence of a liquid phase.&apos; The liquid phase was provided by the dissociation of GasbS particles into liquid gallium and antimony above 555°C. This not only enhanced grain regrowth and densification, as in unalloyed GaSb,&apos; but took on additional importance here for the alloying process. Alloying was speeded up by the resulting liquid-solid interaction as compared to the very slow solid-state diffusion process normally expected at these temperatures.&apos; The results obtained with a series of powder mixtures have been compiled in Table I. It is seen that for mixtures with less than 20 mol pct GaAs, x < 0.2, the compositional ranges increased and for x > 0.2 a GaAs-rich phase and free antimony appeared in the microstructure in sizable amounts.

Jan 1, 1968

By C. L. Berrien

BEFORE the present company was formed, in 1916, each group of mines comprising the old organizations made its detailed daily and monthly mine cost records along the lines used before the consolidation; that is, there was no attempt made to standardize and compare the stope costs of all mines. The general cost sheets for all mines, however, were standardized, and cumulative labor cost sheets were compiled in the general superintendent&apos;s office. At most of the mines, a daily record or distribution sheet for each working place was kept, showing the number of men, hours of drilling, hours of timbering, hours of tramming, cars of ore, cars of waste, sticks of powder and feet of fuse. This information was kept by each shift boss and entered on the distribution sheet by him or, at some mines, by a tram boss. The superintendent solved his own problems under the direction of the general superintendent, but without coming in touch with other superintendents, either through records or general conferences. Probably 95 per cent. of the stopes were square-set worked by day&apos;s pay; there were some back-filling and shrinkage stopes. Many of the development places, such as shaft sinking, station cutting, drifting and raises had always been run by contract. These contracts were given, for no definite period, at so much per linear foot and were measured monthly, or when completed; the men being paid monthly. In some cases, fairness to the employee, was not maintained. On the whole, there was no standardization. There were no stope contracts, because of the objections of the Western Federation of Miners to general contracting in the mines.

Jan 2, 1922

By J. W. Byrkit

Design features and operating methods at the new Ajo smelter are described in detail. Successful operation of a novel method of handling and charging wet concentrates to a deep bath type reverberatory furnace contribute to the daily production of 200 tons of anodes with good results from the standpoint of both metallurgy and economy. THE New Cornelia Branch of the Phelps Dodge Corp. is located at Ajo, Ariz. Large scale mining operations were started at Ajo in 1917, when a 5000 ton leaching plant was put in service to treat the copper carbonate ore that overlaid the sulphide ore-body. In 1924 a 5000 ton flotation plant was built to treat the sulphide ore and the leaching operation was abandoned a few years later. Changes in practice and additions to plant facilities have resulted in a gradual increase in the milling rate which now approaches 30,000 tons daily. Prior to the erection of the Ajo smelter, flotation concentrate was shipped by rail to Douglas, Ariz, where it was treated in the Phelps Dodge smelter. Construction of a one reverberatory furnace smelter to produce an average of about 200 tons per day of copper anodes at Ajo was started early in 1949. Initial heating of the reverberatory furnace was begun on June 21, 1950. Charging the furnace was started on july 8, and the first anodes were cast on July 14. Neither the anode furnace nor the reverberatory furnace has cooled since the initial firing. Fig. 1 is a photograph of the new smelter. Built primarily to eliminate the &apos;300 mile haul of concentrate to the Douglas plant, the new smelter was designed to treat the Ajo concentrate, with a minimum of capital investment. A novel, and relatively simple, method of concentrate handling and furnace charging made unnecessary the installation and operation of expensive storage facilities and reclaiming equipment, and obviated the necessity of holding in storage large quantities of copper-bearing materials. (Patents are pending in the United States and abroad on the Ajo process.) In the selection and arrangement of equipment, consideration was given to the full utilization of all smelting facilities, reducing the amount of idle equipment to a minimum. The layout of the smelter is shown in Fig. 2. The important problem of internal transportation was minimized by arranging the reverberatory furnace, converters, and anode furnace in a compact group and providing storage bins inside the smelter building, within reach of overhead cranes, for fluxing materials and other supplies needed in the daily operation. This can be seen in the sectional view of the smelter given in Fig. 3. Incorporated in the design were many innovations in smelting equipment intended to facilitate operations and effect economies in maintenance expense and manpower requirements. Table I gives operating data of the entire plant. Metallurgy The metallurgical practice at Ajo is based essentially upon the use of a single, deep bath reverberatory furnace for smelting wet concentrate, without concentrate storage facilities. The large reservoir of slag and matte maintained in the furnace serves to equalize, to some extent, the day to day variations in the nature and grade of concentrate and permits

Jan 1, 1954

By Norman D. Fitzgerald

IN 1943 the petroleum industry completed a series of practical adjustments to the acute problems which dominated the scene a year earlier. The crisis in petroleum transportation from the Gulf Coast to the East Coast was met by the completion of overland pipe lines supplementing emergency haulage by tank car so pressure on consumers along the Atlantic Seaboard was appreciably relieved. Later in the year when the western Atlantic was largely cleared of submarines, the sharp reduction in the hazards of marine transportation permitted the resumption of coastwise traffic and imports from South America. Nationwide restrictions in the use of gasoline and fuel oils became necessary as military demands for all petroleum products mounted to high levels.

Jan 1, 1944

By Earl Bardwell

(Butte Meeting, August, 1913.) THE structural relations existing between cuprous oxide and copper were first systematically studied by Heyn1, who suggested that a study of the microstructure of refined copper might be substituted for the analytical methods in vogue for determining the oxygen content of copper coming .;from the refining furnace. Hofman, Green and Yerxa,2 in their paper A Laboratory Study of the Stages in the Refining of Copper, working along the lines suggested by Heyn, showed that a study off the microstructure could be made to yield a correct estimate of the oxygen content of the specimen of refined copper under examination. In order to determine the oxygen content of the specimen of refined copper under examination a photomicrograph was first made. From the relative areas of copper and eutectic, the percentage of cuprous oxide and the corresponding percentage of oxygen were then readily calculated. It was found that the values for oxygen thus obtained corresponded closely with the analytical results. With the idea of utilizing, this method of determining the oxygen content of each charge dipped from the refining furnaces at the Boston & Montana Reduction Plant, the physical testing laboratory was equipped with suitable apparatus for carrying out the work. It may be of interest to describe certain of the methods which have been worked out in, this connection and give such data as have been obtained bearing on the effect of the oxygen content of refined copper upon its conductivity.

Jan 7, 1913

By Bruno Nordberg

HOISTING is one of the earliest endeavors of man with machinery, for hoisting was probably used by the early Egyptians. Treadmills were used for general hoisting until early in the nineteenth century and it was a short step only to attach a Watt steam engine to the rope drum of a hoist. One of the earliest steam hoists was built for a coal mine at Frisne, near Valenciennes, France. It was a remarkable piece of engineering created by James Watt in 1811, using a wooden drum on a vertical shaft. This followed the crude hoist by Holtzhausen in 1803, which used a drum of wood on a horizontal shaft.1 In this country there were examples of crude mine hoists, which have been developed into the efficient machines in use today. African and Australian mines show examples of both extremes, and have an array of fine hoisting equipment exemplified in those built by British manufacturers. The influence of both English and American engineering in hoisting is interestingly evident in Canada. The information available to the writer does not reveal this to be true of South Africa, although American-built hoists have been furnished. Mining camps develop their own style of equipment, adapted to local conditions. For instance, the Butte mining district adheres to the straight drum with friction clutches, because of the great number of levels from which hoisting is done or to which men and material are lowered and the necessity for hoisting or lowering unbalanced. The north Michi-gan copper country uses both straight and cylindroconical drums and hoists continually in balance, so that the drums are not clutched to the main driving shaft. The Joplin mining district, Missouri, has its own peculiar small hoists. Other individual mines or localities in which a number of mines have been developed show individualisticc types of hoists, depending upon their particular problems. In each instance, however, the particular problem must be carefully analyzed, as conditions are seldom so near the same that a number of identical hoists can be used to advantage.

Jan 1, 1940

By C. C. Whittier

CIVILIZATION&apos;S PROGRESS, which has multiplied man&apos;s comforts, conveniences, a n d happiness, is based upon the extensive employment of natural minerals and sources of energy. Mineral resources are basic factors in modern economic development, machine industry, international trade and world power. A survey of mineral consumption shows that the United States leads the world in the production and consumption of energy materials, of metals, and of the large and diverse array of earth materials that fall in the nonmetallic mineral group. The use of nonrnetallic minerals exceeded both the metals and the fuels in the long period before the industrial age, but it is only in the last two decades that consumption of non- metals has kept pace with and approximated in value the output of metals. Although the data of production in the first half of the last century are meager and fragmentary, the record of the past fifty years-the period of most rapid growth-is available, and reveals an astounding growth.

Jan 1, 1933