Search Documents

By W. H. Class

The embrittling effects of oxygen, ozone, nitrogen, air, and surface residues, on NaCl has been investigated. The embrittlement by ozone and oxygen was found to be associated with the formation of a NaClO3 surface compound. In these cases the initial crack that was responsible for fracture (in a bend test) always nucleated at the corners between the tension and side faces. The behavior of air was very erratic and on certain days did not produce enzbrittlement. During these periods, crystals that had become embrittled by the ozone treatment completely recovered their ductility after a short exposure to the ambient atmosphere, It was established many years ago1 that considerable ductility could be obtained in NaCl single-crystal specimens if the crystal surfaces were dissolved in water either during or immediately prior to the test. The original interpretation of this effect by Joffe attributed the enhanced ductility to the removal of surface microcracks by dissolution. Later investigations2'3 have suggested that the exclusion of air from the specimen surface is the criterion for extensive plastic flow prior to fracture. The air em-brittlement in this later work was attributed to the diffusion of gaseous atoms into the surface layers of the crystal, thereby impeding the movement of dislocations. This model satisfactorily accounts for the reembrittlement observed after further air exposure subsequent to the water dissolution treatment. However, the situation has recently become more complex by the observations in several laboratories4-t that under certain conditions air exposure does not impair the ductility of NaC1. It has also been recognized5 that improper drying operations after water dissolution can leave surface precipitates that lead to embrittlement. Cleavage defects on as-cleaved crystals can often be another source of embrittlement. In the present work the effect of the gaseous atmospheres nitrogen, argon, air, oxygen, and ozone, on the ductility of rock salt was studied extensively. The embrittlement resulting from oxygen and ozone exposures was found to be associated with the formation of a NaC1O3 surface film. It is suggested that certain atmospheres, one of which often can be ambient air, which inhibit the formation or favor the decomposition of this compound, can promote ductility. Thus one aspect of the Joffe effect is certainly related to the removal of surface compounds or complexes by water dissolution. The effect of surface precipitates that remain after drying operations and of cleavage defects were also studied. In neither of the latter cases was the embrittlement as severe as that found with a NaClO3 surface layer. PROCEDURE AND SPECIMEN PREPARATION The nature of the embrittlement produced by the agents mentioned above was studied by means of microscopy, mechanical testing, and X-ray diffraction. Specimens were cleaved from large crystals of optical quality sodium chloride obtained from the Harshaw Chemical Co., and, except for those tested in the as-cleaved condition, were given a 15- to 20-sec immersion in distilled water followed by a rinse in absolute methyl alcohol. The specimens were then blotted on a soft, absorbent paper, and dried by a few seconds exposure to a stream of warm, dry air. Such a procedure was found to give a control surface which was microscopically free of residues. (A few crystals were intentionally painted with a concentrated NaCl solution in order to investigate the effect of surface residues). All specimens were of 0.140 sq in. cross-section. Crystals prepared in the above manner were immediately placed in a gas train where they could be exposed to the desired gases for preselected periods of time. For the oxygen and nitrogen exposures, pure reagent-grade gases were employed. The ozone was provided in the form of an ozone-oxygen mixture (approximately 10 pct ozone) prepared by passing commercial grade oxygen over a strong ultraviolet light source. All gases were dried prior to their introduction into the train. Since argon was found to be completely inert in its behavior (i.e., residue-free specimens that were exposed to argon were not embrittled), it was periodically utilized to check the control specimen surfaces as well as the condition of the gas train used for aging the specimens. After exposure to the gaseous media in question, the crystals to be used for the measurement of the strain to fracture were transferred from the gas train to a protective oil bath (without further exposure to the atmosphere) where the tests were conducted in three-point bending. The apparatus was so adjusted that the load could be applied at a constant, continuous rate. Other Snecimens from the gas train were deformed

Jan 1, 1962

By N. Schapiro, R. J. Gray, G. D. Coe

A petrographic and chemical investigation was conducted to determine the occurrence and distribution of the organic and inorganic forms of sulfur in various size and specific gravity fractions of a high volatile, A-rank, Pittsburgh seam coal. The investigation was conducted to aid in the resolution of the problem of how metallurgical coke of lower sulfur content can be produced from high sulfur coals. The Pittsburgh raw coal contains about 2.4% S in two dominant forms: pyritic and organic. Pyritic sulfur constitutes about 57% of the total sulfur in the raw coal and occurs in macroscopic and microscopic-size particles. A plant cleaning process mechanically separates between 50 and 60% of the pyritic sulfur, mainly the macroscopic particles. The organic sulfur constitutes 41% of the total sulfur in the raw coal and 55% of the sulfur in the washed coal. Thus, organic sulfur is not reduced by physical methods of separation. Organic sulfur occurs in all the coal entities, but in general, increases as the exinoid content of the coal increases. In this study, it was found that carbonizing certain selected low gravity coal fractions containing an average of 0.45% pyritic sulfur and 1.01% organic sulfur produced cokes containing an average of 0.22% pyritic sulfur and 0.91% organic sulfur. However, the organic sulfur in the coke is probably derived in part from the heating of pyrite in the presence of carbon. Thus, the total sulfur in the coal carbonized is the most important factor affecting the sulfur content of the coke produced. Concentration of microscopic pyritic and organic sulfur in the middling-type coal indicates the necessity for rejecting as much of this material as is economically feasible. Most of the sulfur introduced into the blast furnace originates from the coke. Although the sulfur content of the hot metal can be controlled by the addition of flux, the flux used restricts the productivity of the furnace by displacing ore and requires first to be smelted; therefore, low sulfur coke is highly desirable. Since the sulfur content of coke is dependent upon the sulfur content of the coals from which the coke is produced, low sulfur coals are required to produce low sulfur coke. In the western Pennsylvania area, large quantities of good coking coal are available from the Pittsburgh seam, but this coal unfortunately contains relatively large quantities of sulfur. To provide information that might be useful in reducing the sulfur content of this coal in the cleaning process, an investigation was conducted to determine the physical and chemical forms in which this sulfur occurs and with what petrographic components it might be associated. The Pittsburgh seam coal, like most other coals, contains two dominant forms of sulfur: one occurs as the minerals pyrite and/or marcasite and is referred to as pyritic sulfur; the other is combined with the coal substance and is called organic sulfur. Pyritic sulfur is amenable to physical methods of separation, whereas organic sulfur is not. Pyritic sulfur particles must be freed from the surrounding coal if they are to be removed in the washing process. Generally, this requires crushing; the required degree of crushing being a function of the size and distribution of the pyrite. The present investigation was conducted to 1) determine the size, distribution and association of sulfur-bearing minerals in the coal and 2) to determine whether the organic sulfur has a preferential association with specific coal entities. If a preferential association exists, this knowledge may be useful in devising a method for organic sulfur reduction. In addition, a study was made to determine the extent to which pyritic and organic forms of sulfur in the coal contribute to the sulfur in the coke produced from this coal. A representative 3%-ton sample of raw coal was crushed to —3 in. and screened into square-mesh sizes: 3 to 1 in., 1 to % in., % to % in., % in. to 10 mesh, 10 to 35 mesh, and 35 to 200 mesh. Separate samples of the -200-mesh fraction and the all-size composite were also collected. Each size fraction (except the -200 mesh) was fractionated on heavy liquids of the following specific gravities: 1.280, 1.300, 1.325, 1.350, 1.375, 1.400, 1.425, 1.450,

Jan 1, 1963

By Faustino Roel

AMONG the problems confronting the mining engineer in Mexico in recent years, labor conflicts have come to occupy s prominent place. Each day they have become more serious and frequently have caused- the ruin of companies. It is therefore necessary for the engineer to understand the Federal Labor Law, the rights and obligations of companies and of their workmen, and the reasons for conflicts; to keep in mind the expense which may be caused companies; and to endeavor to avoid difficulties as far as possible. Our labor legislation is primarily to protect the workman and the constant tendency of the tribunals, including the Supreme Court of Justice, is to support the work- man in his demands against employer$, even at times granting him more than he asks, with no limit other than the economic capacity of the company to com-

Jan 1, 1937

By Charles Will Wright

MINERAL production in almost all European countries suffered a sharp setback because of the war. Plants were damaged, transportation facilities disrupted, and labor dispersed and demoralized. Since the war, due to lack of confidence and economic stability, there has been little incentive to rebuild and expand the mineral industries even though a big demand at high prices exists for mineral products. Most mining and metallurgical companies in Europe hesitate to invest their capital because of the tendency towards nationalizing industry, high taxes, and low output of labor, as well as the deficiency of mine supplies and equipment within their countries. In short, they do not have faith in the future, and for these same reasons and fears most of the mining companies in America will not risk capital investment in Europe. In Europe, including the United Kingdom, free enterprise has been losing ground and as a result the foundation of their economic welfare is being undermined. American mining interests willing to take the initiative could help in counteracting this influence if a way were found for them to co-operate with the European producer without too great a risk.

Jan 1, 1948

By M. Kaitz

A continuing discussion in both the petroleum engineering and economic literature is directed to the difficulties encountered in the use of discounted cash flow rate of return (DCF) as a measure of investment worth. Although useful in most Instances, DCF has been criticized because it is time-consuming in its trial-and-error solution, theoretically invalid, not adaptable to cash flow streams yielding multiple return solutions and not entirely reliable in selecting between mutually exclusive investments. The theoretical invalidity of DCF stems from the reinvestment assumption implicit in the calculation that earnings are reinvested at the DCF rate. The emerging consensus of the economic literature is that the net present value or the present worth of the net cash flow stream (discounting at the average opportunity or cost of capital rate) is more correct and reliable. Other criteria proposed have been ratios of net present value divided by initial investment or by present value of all investments in a project. All of these criteria are simple to determine and explicitly assume a reinvestment rate for [he income generated by a project. This paper develops and discusses a theoretically valid profitability criterion which is simple to compute and retains the appeal of a percent return on investment. It is called "percentage gain on investment" or PGI. It measures the gain an investment is expected to realize over like capital invested in the average opportunity and explicitly considers reinvestment potential. Why add another Concept to the large array of investment criteria now available, any one of which, or perhaps a combination of several, appears to embrace the form's (or individuals) objectives? The answer is that not one of the existing criteria provides both a readily comprehensible and theoretically valid measure of risk coverage that has general application. The proposed PGI does fulfill these requirements. INTRODUCTION An ancient expression warns that "one must yield to the times" — there are better ways of doing things. A review of the petroleum engineering and economic literature on one topic alone, measurement of investment worth, certainly is witness to this truth. In use for a number of years, the DCF has recently received attention, directed mainly to its theoretical invalidity. Several alternatives to DCF have been proposed to provide a valid, simply determined criterion to describe investment worth and to overcome the criticisms previously mentioned. This paper introduces another method called percentage gain on investment (PGI) and is proposed as but one of several yardsticks that should be used in making investment decisions. MEASURES OF INVESTMENT WORTH This paper will consider only those criteria which give weight to the time pattern of future earnings. These criteria are usually compared with an average opportunity rate or cost of capital of the firm to judge the relative worth of the investment. For purposes of demonstration, a 9 percent average opportunity rate will be used throughout this paper. Implicit in the DCF calculation is the assumption that earnings are reinvested at the DCF rate. Some argue, though, that there is no reinvestment assumption,' that the DCF rate is simply that maximum rate of interest one can pay on the investment over the life of the project and break even. The determination of DCF is accomplished by discounting the net cash flow stream at that rate (DCF) which will yield zero. The question is: why should reinvestment potential be explicitly considered in calculating return on investment or other criteria measuring economic worth? Perhaps the answer lies in consistent or equal treatment of future cash flow. It appears entirely illogical to give different present worth value to $1 received, say, 10 years from now, which is the circumstance resulting in comparing projects with different DCF returns. In fact, $1 received in 10 years has the same value regardless of which project generated the income. DCF return thus favors investment projects which are expected to provide early income as compared to those providing long-term income. Not surprisingly, the controversy on reinvestment assumption is an old one. Hoskold' discussed this same problem in 1877. He considered the future income from mineral properties as an annuity or a series of fixed future payments. (As will be demonstrated, his equation can be modified for variable income.) Prior to Hoskold, the value or what one could pay for the mine, was determined with the use of standard, single-interest tables. Here is what Hoskold said with regard to these tables. "This table, and others of its kind, to be found in most works on annuities, is constructed correctly according to

By Milton E. Wadsworth, Edward M. Eyring

BETTER understanding of solid surfaces and their associated adsorption products is of both academic and practical value. The study of detergents and their behavior in cleaning surfaces is fundamentally related to the nature of the products adsorbed and their ability to compete for certain surfaces. Similarly in flotation, the nature of the adsorbate before and after adsorption is basic to clear understanding of the process. The recently developed pellet technique1,2 employing infrared spectroscopy provides a powerful tool for the study of solid surfaces. Absorption bands, which are infrared-active, may be observed for adsorbed products. Also any changes in the surface substrate that occur as a result of adsorption may be detected by means of differential spectra. In applying the pellet technique to solids of large surface area, French and his coworkers3 have surveyed the adsorption of organic flocculants on clay minerals, oleic acid on fluorite, and ammonia on cracking catalysts. Recent work on application of differential infrared spectroscopy to the study of solid surfaces' has demonstrated that the difference between a sample and a reference can be obtained with double-beam instrumentation. In this way displacement of surface products, adsorption of new products, and differences in the substrate, if any, may be detected. Experimental Procedure: Potassium iodide pellets were used in this study, prepared from recrystallized analytical reagent grade KI. Grinding was carried out in a Fisher mechanical agate mortar. Two-gram plates containing the solid under study were pressed in a special evacuated die constructed in the laboratory at the University of Utah." Concentration depended on the solid in question. Zinc sulfide and willemite are sufficiently transpar- ent in the infrared region for concentrations as high as 20 mg of mineral in 2g of KI to be used. Zinc oxide is even more transparent, permitting concentrations as high as 60 mg in a 2-g plate. For non-differential operation, however, much lower concentrations (2 to 10mg/2g KI) had to be used. Spectra were obtained on a Per kin-Elmer 21 double-beam recording infrared spectrophotometer. A sodium chloride prism was used giving a spectral range of approximately 2 to 15 v wave length. For differential runs a resolution of 1000 was used and the scanning speed was controlled commensurate with instrument response. The response was checked continuously and each spectrum was repeated several times. For nondifferential runs a resolution of 927 was used. Zinc oxide used was analytical grade oxide fume. The zinc sulfide was precipitated from solution with analytical grade zinc sulfate and sodium sulfide. The precipitate was washed and centrifuged several times and dried. Before use the precipitate was washed in dilute HCl and then treated with saturated NH4Cl to remove any bulk oxides and sulfates. X-ray patterns of the precipitate were comparable to that of the natural mineral sphalerite. The precipitate was much more satisfactory than finely ground natural ZnS because of its very large surface

Jan 1, 1957

By G. L. Oldright

NEARLY all of the present schemes for treating complex (i. e. lead¬silver-zinc-copper) ores are based on the idea that lead holds, and will hold for some time, the strongest economic place from the viewpoint of supply and demand of all the non-ferrous metals. Copper, it is thought, will come back to its own when European affairs are stabilized, although at that time competition from Chile, Peru, and Katanga, in particular, will be more severe than in pre-war days. The future for silver and for zinc is uncertain. New uses are developing for zinc, and the market has remained better than many expected, but the stabilization of world markets will bring in foreign competition instead of relief. The cost of producing zinc from simple zinc ores, by the retort process, will, from the nature of the labor required and the increasing cost of fuel, increase steadily. As a result, the small producers of purely zinc ores around Joplin are shutting down their mines, even with a good market price for zinc; on the other hand, the producer of lead from complex ores, in the Rocky Mountain states, is confident of a profit from the sale of his lead, and is seeking means to make the zinc in his ore pay some part of the cost of treatment. However, the tonnage costs for mining and ore dressing are much higher in the Rocky Mountain states, as may be seen by comparing tax-return statements from the various states. Even before the recent drop in the price of silver, many mines were operating on a very slender margin of profit; labor and supplies cost more. Mining at greater depth has shown most orebodies to grow increasingly more complex, so that improvements in mining and ore-dressing practice have not been sufficient too compensate for the additional expense involved in beneficiating these ores. The smelters have had to meet the same general economic situation, so they can only give

Jan 3, 1924

By William Glenn

The taking of proper samples of crude ores seems to he less thoroughly understood, or less carefully practiced, than its impor tance requires. We all know how often we encounter the reports of very accurate assays and analyses, the weight of which as evidence wholly depends on the method of obtaining the sample, and is very probably nil, because there has been no proper sampling. Pissages might be cited from technical books, and from current technical literature (all the work of writers whom we delight to honor) to show that even among high scientific authorities there is too little acquaintance with the practical art of the sampler. There is no metallurgical or chemical establishment which does not frequently receive samples truly representing nothing. They consist usually of bits of ore, or what not, selected because they are worse or better than the average of what they are meant to represent. And they are worthless, no matter who made the selection. Where conscious choice is permitted to enter into the operation, a fair sample will not result, unless by a miracle. The work of sampling is often looked upon as within the realm of boys and of pensioners only. At least, though the manual labor be left to subordinates, the principles on which it is conducted and the safeguards with which it is surrounded are not unworthy of the study of experts; and experts should he ready to teach these principles and enforce them in practice. For exact sampling is the indispensable first step towards learning the value of any boxful, carload or shipload of ore. I propose to give a simple account of the method of sampling by hand, such as I have always pursued. There is nothing new about it. So far as I know, it is the immemorial old method, as old at least as Cornish copper-mining. Perhaps my fellow-members in the Institute may suggest improvements in it. If not, it will constitute a record in our Transactions to which laymen and beginners may be referred.

Jan 1, 1892

ALEXANDER, JOHN S, M,'74-6,'81-3 *ASHBURNER, C A, M, '85-7 ASMUS, GEORGE, Dl, '78-80 BACON, D H , M, '00-2 BAYLES, JAMES C , M,'80-2,'91-3 P, '84-5, V,'88-9 BIRKINBINE, JOHN, M, '83-5, V, 'S7-J, P, '91-2 BLAIR, THOMAS S , M, '74-43 BLAKE, WILLIAM P , V,'71-4,'76-7,'05-6 *BLANDY, JOHN F, V,'71-3,'78-9 BLOW, A A, C, '05-7 BOWIE, A J , JR, V,'93-4 *BRAMWELL, J H , A1, '89-91 BROOKS, THOS B , M, '72 BRUNTON, D W , V, 97-8 BUCK, STUART M , M, '83-5 *BURDEN, JAMES A, V,'80-1 BURNHAM, WILLIAM, M, '82-4. CAMPBELL, H H, M, '93-5 CHAMBERLAIN, H S , V, '96-7 CHANNING, J PARKE, V,'08 CHRISTY, S B , V. '91-2, '07-8 CHURCH, JOHN A, M, '79-8l,'94-6, V, '07-8 COGSWELL, W B, V, '74-5,'86-7

Jan 1, 1910

ALEXANDER, JOHN S, M,'74-6,'81-3 ASHBURNER, C A, M, '85-7 ASMUS, GEORGE, Dl, '78-80 BACON, D H , M, '00-2 BAYLES, JAMES C , M,'80-2,'91-3 P, '84-5, V,'88-9 BIRKINBINE, JOHN, M, '83-5, V, 'S7-J, P, '91-2 BLAIR, THOMAS S , M, '74-43 BLAKE, WILLIAM P , V,'71-4,'76-7,'05-6 BLANDY, JOHN F, V,'71-3,'78-9 BLOW, A A, C, '05-7 BOWIE, A J , JR, V,'93-4 BRAMWELL, J H , A1, '89-91 BROOKS, THOS B , M, '72 BRUNTON, D W , V, 97-8 BUCK, STUART M , M, '83-5 BURDEN, JAMES A, V,'80-1 BURNHAM, WILLIAM, M, '82-4. CAMPBELL, H H, M, '93-5 CHAMBERLAIN, H S , V, '96-7 CHANNING, J PARKE, V,'08 CHRISTY, S B , V. '91-2, '07-8 CHURCH, JOHN A, M, '79-8l,'94-6, V, '07-8 COGSWELL, W B, V, '74-5,'86-7

Jan 1, 1910

By Avnulf Muan, P. V. Riboud

The effect of Cr2O3 on melting relations of iron oxide at oxygen pressures slightly above those prevailing in contact with metallic iron has been determined. Liquidus and solidus temperatures of wüstite are raised by the addition of Cr2O3, from 1385°C for pure iron oxide to 1420°C at the peri-ledie point where wüstite, iron chromite, liquid, and gas coexist in equilibrium under the atmospheric conditions used in the present investigation (CO2/H2 = 1). It has been shown in a previous investigation1 that the liquidus and solidus temperatures of iron oxide are drastically increased by the addition of Cr2O3 under the relatively oxidizing conditions prevailing in air. This is to be expected in view of the easy substitution of cr3+ for Fe3+ in crystalline oxide structures which are stable at high oxygen pressures, as demonstrated for instance by the completeness of the solid solution series Fe2O3-Cr2O3 at high temperatures (>1000°C). The stable phase of iron oxide at oxygen pressures approximating those prevailing when metallic iron is present is wüstite. This phase, although commonly represented by the simplified formula FeO for sake of convenience, in reality has a defect structure in which a part of the iron ions are present as Fe3+. It is to be expected that at least a limited amount of cr3 ions will substitute for Fe in this structure when Cr2O3 is added to wüstite. Depending on the ease of this substitution in comparison with that of cr3 substitution for Fe in iron oxide-Cr2O3 liquids under the same atmos- pheric conditions, the liquidus and solidus temperatures of wüstite may increase or decrease upon addition of Cr2O3. The methods of establishing these melting relations and the results obtained are presented in the following. I) EXPERIMENTAL METHOD 1) General Procedure. The quenching technique was used in this study. Oxide mixtures were heated at chosen constant temperatures in an atmosphere consisting of equal parts of CO2 and H2 until equilibrium was established among gas and condensed phases. The samples were then quenched in mercury to room temperature, and the phases present were determined by microscopic and X-ray investigation. 2) Preparation of the Mixtures. Starting mixtures were prepared by weighing and thoroughly mixing Fe2O3 and Cr2O3, or wüstite and Cr2O3. The Fe2O3 and Cr2O3 used were "Baker Analyzed" reagent grades, whereas wüstite of composition was synthesized by reducing Fe203 at 1325°C in an atmosphere consisting of equal parts of CG andHz. In order to avoid contact with crucibles, the equilibration runs were made with small pellets suspended from thin (-0.004-in.) platinum wires. Mixtures made from FOs and Cr203 were readily pelletized at a pressure of 500 atm in a 9.5-mm die, whereas mixtures made from wüstite and Cr203 when treated identically were too weak for handling. In order to obtain a stronger product, these pellets were sintered by heating for 2 min at -1200°C in the same atmosphere as was subsequently used for the equilibration runs (CG/H2 = 1:1). During the sintering, these pellets were wrapped in thin (0.0004-in.) platinum foil, which was stripped off before the equilibration runs. In order to reduce the time needed for equilibrium to be attained, preliminary equilibration of relatively large pellets of each mixture was carried out at -1200°C for 4 to 12 hr. Smaller pellets

Jan 1, 1964

By Robert E. Green, Edmund G. Henneke

The velocities of the three possible modes of elastic wave propagation have been calculated for single-crystal copper at 1-deg intervals throughout the standard stereographic triangle. The results are presented as isospeed contours. The deviations between the direction of maximum energy flux and specimen axes are presented as arrows drawn on stereographic projections. The orientation factors associated with dislocation motion on the primary slip system only and also on all twelve slip systems have been calculated for all three elastic waves. The orientation factors associated with a longitudinal standing wave resonant specimen have also been calculated. The results of these calculatians are compared with earlier calculations on aluminum crystals and the relevance of these results to ultrasonic attenuation measurements is discussed. GREEN and inton' have recently outlined a procedure for determining the orientation factors for dislocation damping in single crystals. The stress field associated with a given mode of elastic wave propagation is resolved on the slip systems in which it is assumed the dislocations are vibrating due to this stress field. Since, at room temperature, slip has been observed on a limited number of systems in fcc and hcp metal crystals, it is assumed that these systems are the appropriate ones to use for the resolving process. This procedure has been applied to aluminum crystals by Hinton and hreen' and to zinc crystals by Henneke and Green.3 In the present paper the modes of elastic wave propagation have been calculated for copper crystals possessing orientations at 1-deg intervals throughout the standard stereographic triangle. The deviation of the energy flux vectors from the specimen axis have been calculated for each mode. The stress field associated with each mode has been resolved on the (111)(110) slip systems in order to determine the orientation factors for dislocation damping. MODES OF ELASTIC WAVE PROPAGATION For any direction in a linear homogeneous aniso-tropic material three elastic modes can be propagated. In general, each of these modes has both longitudinal and transverse particle displacements associated with it and thus are not "pure" modes. However, there is always one component which is greatest in either a longitudinal or transverse direction and hence the mode may be referred to as quasi-longitudinal or quasi-transverse, accordingly. For certain axes of high symmetry pure modes may be propagated. The phenomenon of refraction of the energy flux vector is also exhibited by elastic wave propagation in ani-

Jan 1, 1969

By S. A. LoPilato, J. T. Smith

SEVERAL techniques have been evaluated for cooling the throat area of rocket-nozzle inserts to prevent erosion or fracture of the inserts during exposure to high operating temperatures and pressures. Self-cooled composites, such as infiltrated tungsten, have shown considerable promise for these applications. These composites can be fabricated by infiltrating the refractory matrix with a lower-melting metal or non-metal which is insoluable in tungsten. During firing, the lower-melting substance undergoes a series of continuous endothermic phase changes which absorb sufficient heat to maintain the nozzle matrix material at or below a safe operating temperature. At present, the state-of-the-art has reached a point where the refractory matrix density and microstruc-ture have been established as the critical parameters to be controlled for optimum self-cooled performance.'" Nondestructive testing has been utilized to ensure that porous tungsten billets were of uniform density and free from cracks or other defects prior to fabrication into rocket nozzle inserts. Ultrasonic-velocity techniques have been employed because of their reliability and reproducibility. The purpose of this note is to present and interpret the test data developed for porous tungsten matrices. For evaluation purposes, tungsten powders with Fisher subsieve sizes of approximately 4 and 18 p have been obtained for study from four commercial sources: the General Electric Co., Wah Chang Corp., Fansteel Metallurgical Corp., and Kennametal, Inc. Porous tungsten matrices were fabricated from the powders by hot pressing in induction-heated graphite die assemblies. Typical billets ranged from 3 in. diam, 2 in, high to 5 in. diam, 5 in. high. The ultrasonic-velocity measurement technique employed was through transmission, pulse echo at a frequency of 1.0 mc using matched barium titanate crystal transducers. The testing equipment included a pulsed ultrasonic generator, an amplifier, a specimen holder, and an oscilloscope, as shown in Fig. 1. The porous tungsten thickness was measured to i 0.0005 in, with precision micrometers while the oscilloscope achieved 0.02 psec time measurement accuracy. The time for a sound wave to pass through the billet, the bulk wave velocity, was calculated to 0.5 pct using Eq. [l]: V-} where V = bulk wave velocity, in. per psec, T = specimen thickness, in., and / = time, psec. To develop inspection standards, the bulk density of a porous tungsten billet was determined by the ASTM water-immersion technique.3 The ultrasonic-velocity measurements were completed at seventeen positions for each billet and averaged to develop a characteristic standard velocity for a particular tungsten powder at several density levels. A plot of ultrasonic velocity vs density is presented in Fig. 2 for six different tungsten powders. This graph has been established as

Jan 1, 1967

By H. Foster Bain

(San Francisco Meeting, October, 1911.) [SECRETARY'S NOTE.-This paper, presented in oral abstract, at the San Francisco meeting, was not at first supposed by Mr. Bain to be required for publication in the Transactions; and the excursion to Japan, in which he took part, immediately after the San Francisco meeting, delayed his presentation of the manuscript. After his return to San Francisco, Mr. Bain, in view of the importance of his paper and its discussion, kindly furnished it in full. The delay in its publication (since it was received in April last) has been due, partly to the circumstance that other contributions had meanwhile acquired the "right of way," and partly to the consideration that, the situation contemplated in Mr. Bain's paper having remained practically unchanged, the paper and its discussion would not lose force or timeliness by this lapse of time.-J. S.] No acute observer of public affairs can have failed to observe a growing disposition on the part of the public to change emphasis in government from political equality to social justice. When our own government was founded it was felt to be sufficient to secure to each individual the fullest possible freedom of opportunity, and such a scheme was excellently adapted to the rapid development of a large territory having a small population. As the number of people in a given area increases, there are more points of contact and conflict; each must move in a smaller orbit, and there must be more regulation. Germany is making faster progress in industry than is any other country. The principal reason is the insistence there on team-play. In Germany there are fewer multimillionaires and more socialists (spelled with either a big or little " S ") than in any other of the leading countries; but Germany wins trade and is steadily improving the conditions of life for her citizens. To some, the change from the freest individualism is welcome; to others it is intensely unacceptable. To this fundamental difference in view-point may be imputed much of the vigor with which the controversy regarding coal-lands has been waged. That present conditions in Alaskan coal-fields are extremely unsatisfactory is generally recognized, but there are wide dif-

Aug 1, 1912

By P. R. Gage, R. W. Bartlett

At high temperatues and reduced oxygen pressuves, molybdenum silicicles oxidize to form SiO(g) vathev than a passivating SiO2 film. This is a sevious problem for low-pressure applications of sili-cide-coated rejvactory tnetals. As oxiclalion pvoceeds, the higher oxidntion potential of silicon initially suppresses oxidation of molybdenum and silicon is depleted near the surface. Eventually, silicon depletion causes secondary passivation (SiO2) mid an active to passiue transition in oxidntion behavior at moderately low pressures. At very low pressures, silicon depletion continues until steady-state oxidation of both silicon and rnolyhdenum can proceed at rates propovtional to their initial stoicliiorrzetvies. Ohsel-vations of 'oxidatiou-rate belzcriliov at temperatures from 1101° to 1700°C and oxygen pressures from 10-7 to 1 at in were made using thermogravimetn'c, X-ray diffraction, and elect?*on-rtric?ro/,vobe techniqrres. The experimental results are in good agreement with calculated lirnits for the various types of behavior that were based on tlievtnochernicnl atzd dffusion rate data for the Mo-Si system. A protective oxide film normally forms during the oxidation of elemental silicon. However, at elevated temperatures and reduced pressures this film is not present and oxidation is rapid. wagnerl has shown that this behavior occurs because SiO(g) is more stable than SiO2. The behavior of the silicides at high temperatures is similar but more complicated. Molybdenum and several silicide compounds are involved and the chemical activity of silicon, or the equivalent silicon vapor pressure, can vary considerably in these phases. Also, diffusion in the silicides resulting from reactions in which a higher silicide is reduced to a lower silicide, or molybdenum containing dissolved silicon, must be considered. EXPERIMENTAL AND ANALYTICAL METHODS Isothermal oxidation experiments were conducted using hot-pressed MoSi2 and Mo5Si3 wafers. Each experiment was conducted at a fixed oxygen pressure by controlling the flow of oxygen in and out of the furnace chamber. Most of the experiments were conducted in a molybdenum-wound tube furnace. Special construction features, including use of a high-purity dense A12O3 refractory tube, permitted operation in high vacuum to 1500°C. Higher temperatures could be obtained at higher working pressures and with a sacrifice of tube lifetime. Temperature was measured with three Pt 6 pct Rh/Pt 30 pct Rh thermocouples and controlled with a proportional controller. Weight changes were monitored with a quartz spring balance. The few experiments, at higher temperatures and low pressures, were conducted in a cold wall vacuum chamber using induction heating with direct susceptance of the sample. Because of the variable levitation effect of the induction coil on the sample, weight changes could not be monitored continuously in these experiments. All samples representing both experimental methods were weighed before and after oxidiation and examined with a microscope and analyzed by X-ray diffraction. The analytical treatment assumes equilibrium at interfaces and uses existing thermodynamic data. For convenience, equilibria are expressed as chemical potentials or as vapor pressures of the gases involved. The resulting differences in equilibrium vapor pressure between adjacent interfaces and between the surface and external atmosphere drive diffusion processes in the solid and gas boundary film, respectively. These diffusion processes govern the rate of oxidation. A bibliography of the sources of thermochemical data for the reactions pertinent to the Mo-Si-O system is given in Table I. Reactions are listed with the sources of free-energy data referenced. Since all of these reactions involve one or more gas species, usually oxygen, a plot of the product-gas chemical potential, -RT In Pg, vs absolute temperature for each reaction is given in Fig. 1. These curves can be used to determine equilibrium vapor pressures or to compare the stability of different compounds in the various gases: O2, Si, SiO, and Moo3,. The data of Table I and Fig. 1 were used to determine the analytical results presented in this paper. EXPERIMENTAL RESULTS The weight changes for three MoSi, samples oxidized at 1500°C are plotted against time in Fig. 2. The treatments were identical except for the indicated variance of oxygen pressure and each curve represents one of three characteristic types of behavior that were observed. The upper curve is an example of passive oxidation, which is defined as

Jan 1, 1965

By T. A. Dungan

THE thermal processes for the production of metallic magnesium can be divided into two general classifications, the direct reduction of magnesia with carbon and the indirect reduction of compounds of magnesium by reducing agents that are themselves products of carbon reduction. The latter are so chosen as to cause reduction of magnesium compounds wherein only the magnesium is liberated in the vapor phase. Reducing agents used are: calcium carbide, silicon carbide, silicon, aluminum, various silicides or combinations of calcium, aluminum, silicon in iron. All of these are products of highly endothermic reactions and, with the exception of scrap aluminum, can be produced in an open, submerged arc furnace; that is, the arc is covered only by the charge itself. The more investment in energy required to prepare such a reducing agent, the less is the energy required in the subsequent step to reduce the magnesium compound to the metal. It is impossible, however, to avoid the laws of thermodynamics, no matter how much circumambulation is resorted to in the preparation of successively more powerful reducing agents. Since each such step carries forward its own inefficiencies, it appears evident that the ultimate status of such processes is dependent upon the development of by-products. EARLY EXPERIMENTS IN DIRECT REDUCTION The direct reduction of magnesium oxide by carbon has a decided appeal to both the scientist and the industrialist. The successful production of the carbothermic plant at Permanente is a significant fact in the substantiation of this concept. Like most developments, however, the history of carbon reduction of magnesia is not one of triumph after triumph, or immediate heady success to the investigators. It is understood that one of the early investigators conducted an experiment wherein he placed carbon and magnesia in one end of an evacuated tube and managed to heat this end to a temperature high enough that magnesia and carbon deposited at the other end of the tube. The charge, unreduced, appeared to have been completely transported from the hot to the cold end of the tube. This raised doubt for some time as to whether magnesia could be reduced at all with carbon. It was correctly suspected, however, that the magnesia was in fact reduced and the resultant magnesium vapor and carbon monoxide reacted upon one another upon reduction in temperature to reform the starting ingredients. Attempts were then made to dilute the two vapors by passing a considerable stream of hydrogen through an arc furnace charged with magnesia and carbon. Thus by dilution of the products it was expected to obtain metallic magnesium. The results were positive and metallic magnesium was

Jan 1, 1944

L. C. UREn,* BerkelEy, Cal. (written discussion).—I heartily concur with Rlr. .Fobs concerning the need for advanced courses on various phases of Petroleum Engineering. I think that his criticism is probably true of most of the engineering schools that are specializing at all in Petroleum Engineering, that is, that most of their so-called graduate courses are not of graduate caliber but are merely more specialized aspects of undergraduate subjects. It would undoubtedly be to the advantage of the petroleum profession if more advanced work could be offered in a few of the leading engineering institutions so that there would be something substantial to offer graduate students wishing to return after a period of undergraduate work, for additional training. There is no doubt but that a better trained engineer, more useful to the oil industry, could be secured from schools offering such advanced training. The problem of adpting our instruction to fit the needs of engineers trained along other lines who wish, after completion of their undergraduate work, to enter thc petroleum engineering field, is a more difficult one. It has been my experience that such men are usually sadly deficient along certain lines and that they are really not prepared for the more advanced work in Petroleum Production Engineering until they have gone back over the work which they have missed in their undergraduate training. I note that Mr. Fohs suggests that other eastern and western colleges not now stressing Petrolelim Engineering, should be encouraged to take up advanced work of this character. With this, however, I cannot agree unless the institutions arc also prepared to offer a full sequence of undergraduate work on which the more advanced courses may be superimposed. Whether or not there is a need for additional engi-ncering colleges entering the petroleum engineering field is an open qucstion. I believe that we arc turning out enough petroleum engineers at the present time and that none of the six institutions now specializing in this field arc overcrowded. Morc-ovcr, they are fairly well distributed over the country, though there may be room for an additional school in the field in the eastcrn section of the United States. F. W. Padgett, Norman, Okla. (written tliscussion).—Assuming that the stnclcnt has the proper fundamentals, that is, general science and a knowledge of the technology of the industry, then the problem is: What courses should be offered from the graduate standpoint? (a) Course Work.—His knowledge of the technology of the industry can be extended advantagcously by means of one and two-hour courses, which consist in a more detailed survey of the various branches of the industry. (b) Lilerdure.—This work may, or may not, be connected directly with his research problem. The student should become familiar with methods of locating articles in the 1iterature; should also become familiar with all the important original

Jan 1, 1928

By John A. Gann

The following investigation constitutes a brief réumé of the more important binary magnesium alloys from the standpoint of metallo-graphic technique, and the effect of heat treatment on structure and properties. The comparative newness of the subject justifies this procedure as a preface to a more detailed study of each individual series of alloys. The work was started with the idea of practical application in the industry rather than as a theoretical investigation. The alloy compositions studied were selected as those most likely to show whether heat treatment would produce beneficial results. Furthermore, it was considered satisfactory to use commercial 99.9 per cent. magnesium, the best commercial grade of alloying ingredients, and to limit the time of heat treatment at the expense of incomplete equilibrium. These facts must be kept in mind when examining the results obtained, and the conclusions drawn. Preparation of Alloys All melts were made in an oil-fired cast-steel pot, approximately 12 in. dia, by 12 in. deep. Approximately 15 lb. of flux and 50 lb. of magnesium were melted and the calculated amount of alloying metal was added. After thorough alloying and puddling, the metal was chill cast in a graphite mold with four 1/2 by 1/2 by 4 in. bars fed from a common sprue and runner. The next higher composition alloy in a given series was made by adding the calculated amount of metal to the heel from the preceding cast. The pot was thoroughly cleaned after each series and new flux then introduced, thus avoiding possible contamination from earlier melts. The percentage compositions given in Table 1 are the calculated values. While not all alloys were analyzed, enough were checked to indicate that the reported compositions are correct to a few tenths of one per cent. A more detailed description of the foundry methods employed has been given in a previous paper. 1

Jan 1, 1929

By John A. Gann

The following investigation constitutes a brief réumé of the more important binary magnesium alloys from the standpoint of metallo-graphic technique, and the effect of heat treatment on structure and properties. The comparative newness of the subject justifies this procedure as a preface to a more detailed study of each individual series of alloys. The work was started with the idea of practical application in the industry rather than as a theoretical investigation. The alloy compositions studied were selected as those most likely to show whether heat treatment would produce beneficial results. Furthermore, it was considered satisfactory to use commercial 99.9 per cent. magnesium, the best commercial grade of alloying ingredients, and to limit the time of heat treatment at the expense of incomplete equilibrium. These facts must be kept in mind when examining the results obtained, and the conclusions drawn. Preparation of Alloys All melts were made in an oil-fired cast-steel pot, approximately 12 in. dia, by 12 in. deep. Approximately 15 lb. of flux and 50 lb. of magnesium were melted and the calculated amount of alloying metal was added. After thorough alloying and puddling, the metal was chill cast in a graphite mold with four 1/2 by 1/2 by 4 in. bars fed from a common sprue and runner. The next higher composition alloy in a given series was made by adding the calculated amount of metal to the heel from the preceding cast. The pot was thoroughly cleaned after each series and new flux then introduced, thus avoiding possible contamination from earlier melts. The percentage compositions given in Table 1 are the calculated values. While not all alloys were analyzed, enough were checked to indicate that the reported compositions are correct to a few tenths of one per cent. A more detailed description of the foundry methods employed has been given in a previous paper. 1

Jan 1, 1929

By Robert B. Coleman

The recent surge in demand for uranium in the US, accompanied by a significant increase in price, has stimulated the search for and development of lower grade ore bodies. At the mill, this translates into much larger throughputs and-compounded by many recently enacted environmental considerations-has made the cost of milling a critical factor in today's uranium production economics. The three conventional milling methods employed in the extraction of uranium ores are reviewed in the following sections.

Jan 10, 1978