Search Documents

By F. J. Haller

IN 1943, we found, in the new Mather operation, a very unusual and disappointing condition in the footwall rock where all of our main haulageways were to be located. With the exception of a few hundred feet out of the thousands then planned and since driven, all of the openings require support. In general, the ground is not particularly heavy, at least by our standards, but it must be supported and the back carefully covered. Also, our operations require rather wide plat openings (16 to 18 ft) and rather flat curves at the turn-outs, all of which adds to the problem. When this completely unforeseen condition was discovered, ordinary timbering was the only answer, because of the impossibility of obtaining adequate steel supplies in time due to war shortages. Then by the time steel supplies were obtained and a practice developed, we found ourselves with between four and five miles of main haulage drifts and plat openings of a permanent nature, all of which were supported by hardwood timber, some of which had already rotted to an unsafe degree. Also, our drifting program was adding some two miles per year to the above figure. F. J. HALLER, Member AIME, is Superintendent, Mather Mine, Cleveland-Cliffs Iron Co., Ishpeming, Mich. AIME Columbus Meeting, September 1949. TP 2840 A. Discussion (2 copies) may be sent to Transactions AIME before May 31, 1950. Manuscript received Aug. 22, 1949. Revision received Jan. 17, 1950. To give all of the details of our experiments, studies, and experiences would fill a large book, but we were satisfied that our organization had done an excellent job, starting from scratch. You can appreciate our surprise when we discovered that we had added very little to an existing record. Attention was called to a footnote in a copy of "Carnegie Pocket Companion" year 1923. The note read: "Full information as to uses of H-Beams is given in pamphlet entitled 'Steel Mine Timbers.' " A search of our Engineering Library brought to light a pamphlet printed in 1911 showing extensive use of steel for this purpose. Except for welding in place of riveting, we have added very little to the designs in that book. We have, however, developed an experience which proves, at least to our own satisfaction, that steel mine supports pay off under the proper conditions. We are now convinced, in spite of the relatively high initial cost of materials, that steel sets, because of comparatively low installation cost, are actually cheaper than either treated or untreated wood sets, if they are properly designed and adapted. Several Sections in Use: Convenience guided our first experiments in steel sets, since for a number of years, we had used the 4-in. WF, 10 lb per ft section in 10-ft lengths as safety forepoles along with wood forepoles. This section replaced the 40-lb rail which had formerly been used for the purpose. Having the 4-in. WF sections on hand, it was natural that our first experiments in steel sets involved their use. Later, the rolling of the 10-lb section was discontinued in favor of the much stronger 13-lb section, which is now standard for both legs and caps in areas of no particular weight, but which, none the less, require permanent support. Our experiments involved the use of the 10- and 13-lb sections as legs and 6- and 8-in. I beams, 16 and 23 lb per ft, respectively, as caps. Experience soon indicated that, if the ground were heavy enough, and the opening wide enough to require a cap stronger than 13-lb, the 8-in, 23-lb should be used, eliminating the 6-in. I beam. We now know that the 8-in. WF section of the same weight, which we propose to use in the future, is considerably stronger for the amount of money involved. Comparative Strengths: Tables I to IV giving strengths of several species of timbers as compared with the structural sections that we now use have been prepared in accordance with accepted practice. Experience indicates that failure due to compression perpendicular to the grain of the wood does not destroy the effectiveness of a wood set frequently enough to be a practical factor. Therefore, no table of these values is included.

Jan 1, 1951

By W. H. Emmons

This paper is the second of a series treating the relations of ores of the metals to igneous rocks. In the first paper1 the general problem was outlined and the normal downward changes in metalliferous lodes were briefly stated, with references to earlier papers treating the relations of ores to depths of their formation. The present paper by a number of examples illustrates the relations treated in the first paper. These examples are chosen chiefly from the larger mining districts because their underground developments are more extensive, but the same relations are shown in maps of scores of undeveloped areas in which the main geological conditions are nearly similar. Ecology of Metalliferous Deposits Ore deposits are divided into three groups: 1, Those formed by sedimentary processes; 2, those deposited by meteoric waters; and, 3, those formed in connection with igneous processes. The last group is the most important. It includes the magmatic segregations, which are igneous rocks in the strict sense, and the veins and related deposits, which were formed by precipitation in channels from solutions originating in cooling intrusives. These deposits may be divided into two groups: 1. Those related to intrusives as basic as diorite; and, 2, those related to intrusives more acid than diorite. The second group probably includes more than 95 per cent. of all lode ores. Nearly all of the ores of this group are associated with granitic batholiths or are in positions where it is reasonable to suppose that such a batholith, not yet exposed by erosion, underlies the area containing the deposits. The batholiths are great masses of deep-seated igneous rocks. When they are intruded most of them are probably as basic as diorite and some

Jan 1, 1927

By Reuel A. Cochrane, Harry H. Angst

The successful exploitation by opencut methods of the low-grade porphyry copper deposits is due to the economical handling of large tonnages. Large tonnages are possible only if the rock material is broken so that the large power shovels can operate with minimum delays. This is particularly true at the New Cornelia mine, where the dense, hard, tough rock material creates problems not encountered in most of the porphyry copper mines. The introduction of churn drills at the New Cornelia for primary drilling, in 1936, necessitated a complete change in the methods of breaking ground as formerly air drills had been used. The blasting operations are of particular interest because of the handling of great quantities of high explosives in safely and efficiently fragmenting the hard rock material. Rock Formations At the New Cornelia mine the rocks are quartz monzonite with a diorite border facies intruding a rhyolitic series. Overlying these formations is a fanglomerate formation composed of boulders of monzonite, diorite, rhyolite, and other types of rock of unknown derivation. (The word "fanglomerate" is used in this paper in referring to the local conglomerate type of rock formations.) The ore body is approximately 4800 ft. long and 2800 ft. wide, and is of the disseminated type. Mineralization occurs principally in the quartz monzonite and to some extent in the adjacent diorite and rhyolite. The principal ore minerals are chalcopyrite, bornite, and a small amount of chalcocite. Over a considerable area the quartz monzonite is extremely hard and siliceous in character, owing to pegmatitic zones of alteration. The hardness of the ground depends on the intensity of the silicification. In a small area in the pit, the monzonite contains an abundance of pyrite accompanied by sericitization and is soft and easily fragmented. This is true also in the remaining oxidized portion of the ore body. The diorite and rhyolite formations, like the monzonite, vary from extremely hard to very soft material, but on the whole are easier to fragment than the monzonite. Jointing is prevalent in all the rock formations and plays an important role in the blasting efficiencies. In the fanglomerate formation, numerous well-defined joints, widely spaced, tend to make the ground blocky when blasted. This is a deterrent to good fragmentation. In the other rocks the joints are more numerous and are closely spaced, except in localized areas where the formations are extremely hard. These descriptions indicate that the lowest blasting efficiency will be obtained in the harder formations, from which the major portion of the mine production is obtained; namely, the monzonite and rhyolite. All rock formations mined at the New Cornelia pit are so hard that excavation

Jan 1, 1943

By Harry H. Angst, Reuel A. Cochrane

The successful exploitation by opencut methods of the low-grade porphyry copper deposits is due to the economical handling of large tonnages. Large tonnages are possible only if the rock material is broken so that the large power shovels can operate with minimum delays. This is particularly true at the New Cornelia mine, where the dense, hard, tough rock material creates problems not encountered in most of the porphyry copper mines. The introduction of churn drills at the New Cornelia for primary drilling, in 1936, necessitated a complete change in the methods of breaking ground as formerly air drills had been used. The blasting operations are of particular interest because of the handling of great quantities of high explosives in safely and efficiently fragmenting the hard rock material. Rock Formations At the New Cornelia mine the rocks are quartz monzonite with a diorite border facies intruding a rhyolitic series. Overlying these formations is a fanglomerate formation composed of boulders of monzonite, diorite, rhyolite, and other types of rock of unknown derivation. (The word "fanglomerate" is used in this paper in referring to the local conglomerate type of rock formations.) The ore body is approximately 4800 ft. long and 2800 ft. wide, and is of the disseminated type. Mineralization occurs principally in the quartz monzonite and to some extent in the adjacent diorite and rhyolite. The principal ore minerals are chalcopyrite, bornite, and a small amount of chalcocite. Over a considerable area the quartz monzonite is extremely hard and siliceous in character, owing to pegmatitic zones of alteration. The hardness of the ground depends on the intensity of the silicification. In a small area in the pit, the monzonite contains an abundance of pyrite accompanied by sericitization and is soft and easily fragmented. This is true also in the remaining oxidized portion of the ore body. The diorite and rhyolite formations, like the monzonite, vary from extremely hard to very soft material, but on the whole are easier to fragment than the monzonite. Jointing is prevalent in all the rock formations and plays an important role in the blasting efficiencies. In the fanglomerate formation, numerous well-defined joints, widely spaced, tend to make the ground blocky when blasted. This is a deterrent to good fragmentation. In the other rocks the joints are more numerous and are closely spaced, except in localized areas where the formations are extremely hard. These descriptions indicate that the lowest blasting efficiency will be obtained in the harder formations, from which the major portion of the mine production is obtained; namely, the monzonite and rhyolite. All rock formations mined at the New Cornelia pit are so hard that excavation

Jan 1, 1943

By C. F. Weinaug, P. M. Blair

Many difference equations used to approximate reservoir flow problems treat the phase pressures implicitly but not the mobility-density coefficients. Such difference equations are neither wholly explicit nor implicit, but might be described as mixed. Mixed equations are relatively easy to apply. But the associated time truncation error is relatively large, and when used to solve problems characterized by high flow rates, these equations may be unstable for practical size time steps. This paper outlines the development of a completely implicit difference analogue for reservoir simulation, along with a Newtonian iterative method for solving the resulting nonlinear set of algebraic equations that arise at each time step. While this implicit equation requires two to three times more work than does the mixed equation, it is shown to markedly decrease the time truncation error and to yield a stable solution for much larger time steps than does the mixed equation. INTRODUCTION Calculation of multiphase, multidimensional flow in porous media is generally accomplished by numerical methods that involve approximating systems of partial differential equations by systems of partial difference equations. The early development of difference equation techniques was directed toward the solution of linear differential systems. However, the equations of multiphase fluid flow through porous media are highly nonlinear in that mobility and density often are strong functions of pressure and saturation. Thus, solution of the flow problems by difference equations involves solving sets of algebraic equations whose coefficients change from step to step of the calculations. Current practice is to evaluate most coefficients at the beginning of a time step and then to apply difference methods well suited for solving linear problems. At least two major difficulties arise from the use of this practice. First, evaluation of coefficients at the old time level and evaluation of pressures at the new time level results in larger time truncation errors near displacement fronts than if all quantities in the distance derivative were evaluated at the same time level. Second, evaluation of mobility coefficients at old time levels results in an unstable difference equation in regions of high flow rate. The first of these difficulties often results in optimistic recovery behind the displacement front, and the second requires the use of small time steps or special techniques in solving coning problems1 or problems of gas percolation.2 Evaluation of all quantities in the distance differences at the new time level results in a completely implicit difference system. Such a difference system has a lower time truncation error than equations in which mobilities are evaluated at the old level and pressures evaluated at the new level. The algebraic equations resulting from the fully implicit difference equation are, in this case, nonlinear and require some iterative method for their solution. This paper develops fully implicit difference equations for two-phase flow in porous media, describes their solution by Newtonian iteration, and gives examples of problems more easily solved by the new method than by previous methods. EVOLUTION OF DIFFERENCE EQUATIONS FOR NONLINEAR PROCESSES The completely implicit difference equation used in these calculations results from evolution beginning with explicit difference equations, proceeding through what we will call "mixed" equations, and arriving now at a completely implicit equation. Let us illustrate the evolution by considering different analogs of the nonlinear equation

Jan 1, 1970

By John S. Johnson, Thomas Fraser

SIZING is the process of separating mixed particles into groups of particles all of the same size, or into groups in which all particles range between certain definite maximum and minimum sizes. In coal preparation, sizing is generally accomplished by passing the coal over screens. Separation by differential settling in air or water currents has been adapted to the special field of separating very fine sizes, and these processes are in commercial use to a relatively small extent in the coal industry. Separation with screens is a very old industrial practice. Agricola described the use of screens for ore treatment in the middle ages. In the literature of the British coal industry references were made to the screening of coal as early as 1589, but the practice of extensive sizing for the market did not become general until the last half of the nineteenth century. In America, the practice of sizing developed first in the Pennsylvania anthracite region, beginning with the use of rakes' in the mine working places to recover coarse coal. This mining procedure left the fines in the mine. Preparation outside the mine started with the installation of station¬ary cast-iron plates with 4 to 6-in. square holes. The run-of-mine coal was dumped upon the platforms, the large pieces of rock were picked out by hand, and the large lumps of coal were broken with hammers. The term "breaker," which still applies to the anthracite-preparation plant, originated with this practice, but the term is no longer descriptive of the entire function of the plant. In 1884, the first power-operated anthracite coal breaker' was erected by Gideon Bart at his colliery at Wolf Creek near Minersville, Pa. This plant utilized a system of rolls for breaking the coal and revolving screens for sizing. The plant was driven by a steam engine. It 'could handle

Jan 1, 1943

By Ellis Clark

THE mining town of Pribram is situated in Central Bohemia, on the western slope of the Heiliger Berg, 30 miles southwest from Prague. Birkenberg, the village in which most of the shafts and ore-dressing establishments are situated, is built on a mountain of the same name. It is about a mile from Pribram, is 1700 feet above the sea, and is surrounded by graywacke rocks of Silurian origin, which are intersected by greenstone dikes, and in the southerly, southeasterly, and southwesterly direction are bounded by granite. The graywacke formations consist on one side of graywacke sandstone and quartzite, and on the other of graywacke slates. These last are separated from the first in the immediate vicinity of the mines by a graywacke seam converted into clay. For many years this so-cal led clay seam (lettenkkluft) was considered as a boundary of the ore deposits in both zones of graywacke. The graywacke formation is divided according to its hardness, structure, texture, and color, into fine, coarse, compact, slaty, whitish-gray, reddish-gray, and black graywacke. The, miner divides the formation into four divisions. The first or lowest division, which is in contact with the granite, consists of a fine-grained dirty gray slate; the -second is a very fine to a very coarse schist, white to reddish-gray in color, and rich in quartz, but containing little mica; the third consists of a slate with a contused cleavage, which has a dirty gray, dark gray, and very often black color and is often graphitic in its composition ; the fourth consists of a fine to coarse-grained graywacke schist, of a grayish-white or reddish-gray color, and rich in quartz. The cleavage in all four divisions strikes from northeast to southwest, and the dip is sometimes northwesterly, sometimes southerly, and often vertical. All four zones are cut through by a great number of diorite and greenstone dikes and chimneys. The thickness of these dikes, which are of

Jan 1, 1881

By Worthen Bradley

A BETTER understanding of what is happening in the domestic quicksilver industry, and what is likely to happen, can be had after reviewing some of the highlights of the past four years. Hitting the high spots in chronological order, they are: February 1939-Army and Navy Munitions Board starts investigation on civilian and war needs of certain "strategic materials," including quicksilver, with a view to recommending stock piles. Every known producer is canvassed by the end of the year.

Jan 1, 1942

By R. A. Grange, H. M. Stewart

Man.; steel parts may crack if quenched directly into a bath near room temperature, but not if quenched at a temperature just above the range where martensite forms and then allowed to cool slowly to room temperature. This latter procedure, which is the basis for such modern hardening techniques as "martempering" and "isothermal quenching," may entail some sacrifice in depth of hardening but very little, if any, in intensity of hardening. In planning such treatments, it is necessary to know the upper limit of the martensite range, and often desirable to know the proportion of martensite that would form on cooling to any lower temperature; furthermore, the tendency of a particular steel to crack when quenched is unquestionably associated with the temperature range of martensite formation, and consequently knowledge of this range aids in selecting the optimum composition for a given application. Certain puzzling phenomena associated with the properties of quenched and tempered steel may be at least partly clarified as the manner in which martensite forms is more fully understood. Information on the temperature range of martensite formation, particularly with respect to how much martensite results from quenching to a given temperature, is lacking for most commercial types of carbon and low-alloy steel. These considerations led us to study martensite formation in 14 carbon and low-alloy steels. The resultant data may be directly used in the following ways: (I) for selecting the lowest quenching temperature at which no martensite will form; (2) for selecting the highest quenching temperature at which virtually all marten . site will form, thereby avoiding quenching to an unnecessarily lower temperature with attendant danger of cracking; and (3) in producing a mixture of tempered martensite and bainite, which in high-carbon steels has been found to possess somewhat better ductility than tempered martensite, yet does not require the full transformation time necessary for a completely bainitic (austempered) structure. PART I. OBSERVATIONS OF MARTENSITE FORMATION IN FOURTEEN CARBON AND LOW-ALLOY STEELS Transformation of austenite to pearlite or bainite can be conveniently studied by observing the change that occurs over a period of time at constant temperature; such studies are the basis of the isothermal transformation diagram (S-curve). This isothermal technique is not applicable to martensite formation, which occurs within a time interval too small to measure, at least by any ordinary means. For all practical purposes, therefore, martensite may be regarded as forming only during cooling and not during a period of time at constant temperature. As austenite is cooled below

Jan 1, 1947

By H. M. Stewart, R. A. Grange

Man.; steel parts may crack if quenched directly into a bath near room temperature, but not if quenched at a temperature just above the range where martensite forms and then allowed to cool slowly to room temperature. This latter procedure, which is the basis for such modern hardening techniques as "martempering" and "isothermal quenching," may entail some sacrifice in depth of hardening but very little, if any, in intensity of hardening. In planning such treatments, it is necessary to know the upper limit of the martensite range, and often desirable to know the proportion of martensite that would form on cooling to any lower temperature; furthermore, the tendency of a particular steel to crack when quenched is unquestionably associated with the temperature range of martensite formation, and consequently knowledge of this range aids in selecting the optimum composition for a given application. Certain puzzling phenomena associated with the properties of quenched and tempered steel may be at least partly clarified as the manner in which martensite forms is more fully understood. Information on the temperature range of martensite formation, particularly with respect to how much martensite results from quenching to a given temperature, is lacking for most commercial types of carbon and low-alloy steel. These considerations led us to study martensite formation in 14 carbon and low-alloy steels. The resultant data may be directly used in the following ways: (I) for selecting the lowest quenching temperature at which no martensite will form; (2) for selecting the highest quenching temperature at which virtually all marten . site will form, thereby avoiding quenching to an unnecessarily lower temperature with attendant danger of cracking; and (3) in producing a mixture of tempered martensite and bainite, which in high-carbon steels has been found to possess somewhat better ductility than tempered martensite, yet does not require the full transformation time necessary for a completely bainitic (austempered) structure. PART I. OBSERVATIONS OF MARTENSITE FORMATION IN FOURTEEN CARBON AND LOW-ALLOY STEELS Transformation of austenite to pearlite or bainite can be conveniently studied by observing the change that occurs over a period of time at constant temperature; such studies are the basis of the isothermal transformation diagram (S-curve). This isothermal technique is not applicable to martensite formation, which occurs within a time interval too small to measure, at least by any ordinary means. For all practical purposes, therefore, martensite may be regarded as forming only during cooling and not during a period of time at constant temperature. As austenite is cooled below

Jan 1, 1947

By K. K. Clark, W. H. Somerton

The feasibility of reducing pressures needed to fracture formations by heating the borehole intensively has been investigated on a laboratory scale. Reductions in fracture pressures of heated Bandera, Berea and Boise sandstone cores were observed at various confining pressures, simulating reservoir stress conditions to a depth of 5,000 ft. Both permeable and impermeable borehole boundary conditions were tested. Three heating conditions were used in the tests. One group of samples was heated in a furnace to a temperature of 600C, cooled to room temperature., and then tested for fracture pressures. Two other groups of samples were heated with a borehole heater to maximum borehole wall temperatures of 625 and 792C, then cooled and tested. In all cases, heated samples showed substantial reductions in fracture pressures compared to unheated samples. The higher temperature borehole heated samples showed the greatest reduction, amounting to 70 per cent in the extreme case. In actual application to wells, it was concluded that fracture pressures may be reduced by 20 to 50 per cent by intensive borehole heating before fracturing. INTRODUCTION Hydraulic fracturing of oil and gas wells is an accepted and effective technique for increasing well productivity in many areas, but is notoriously unsuccessful in other areas. The technique becomes less interesting for production stimulation purposes when excessive fracture pressures are necessary. Formations which do fracture but require high pressures, probably form horizontal fractures. There is good evidence to indicate that some formations do not fracture at all, but yield plastically under high pressure. Thus, any technique which will make formations easier to fracture or will reduce fracture pressures is potentially interesting to petroleum producers. Horizontal fractures generally occur in planes of weakness, such as bedding planes, and at pressures equaling or exceeding the effective overburden stress. In the unusual case where planes of weakness do not exist, a slightly higher pressure must be applied to overcome the tensile strength of the rock. In general, high fluid-loss fracturing fluids are conducive to the formation of horizontal fractures.1 Vertical fractures, when they do occur, are initiated at pressures generally lower than overburden pressure and are favored by low fluid-loss fracturing fluids or impermeable boreholes. The pressure necessary to create a vertical fracture in an impermeable, elastic medium can be predicted from the so-called "thick-walled cylinder" equation: Pf = 2 or+ st.............(1) where pf = fracture pressure or = radial stress st = tensile strength of medium. This equation indicates that to fracture it is necessary to overcome a tangential compressive stress, induced by and equal to two times the radial confining stress, plus the tensile strength of the medium. If the above equation held strictly true for rocks, very little could be done to reduce fracture pressure. The tensile strength of the rock might be reduced somewhat, but any change in st would be small compared to the magnitude of the tangential stress at reasonable subsurface depths. Laboratory tests have shown that actual fracture pressures exceed values predicted from Eq. 1 by factors of 1.4 to 28.6.1,2 Eq. 1 thus does not properly describe the

Jan 1, 1966

By Charles S. Barrett

Metallurgists are making use of the stereographic projection to a steadily increasing extent. In the last five years no less than 20 papers in American metallurgical journals alone have employed the stereographic projection; recent books on physical metallurgy, plastic deformation, X-rays and their applications, and crystal structure use it. Mineralogists have used the stereographic projection for many years in the description of symmetry classes and crystal planes, for it presents an accurate, easily understood plot of any angular relations in crystals with all unessential features eliminated (such as the accidentally determined size and shape of crystal faces). In metallography and physical metallurgy the projection is much used for the analysis of markings appearing on polished grains: slip lines, twins, cracks, structures formed by precipitation, magnetic-powder patterns, etch pits, etc. Data from certain types of X-ray photograms are most conveniently analyzed by its use, particularly those for determining the orientation of single crystals or the preferred orientation of grains in an aggregate. Calculations of how to tilt or cut a crystal parallel to a certain crystallographic plane or to reflect X-rays from a certain plane are rapidly carried out. It has been adopted almost universally to the exclusion of other methods by those studying the deformation of metallic crystals, save where the accuracy required is greater than a few tenths of a degree. Any directional property in a crystal or polycrystalline material can be shown on a stereographic projection; for example, the modulus of elasticity, yield point, etc. It has been repeatedly called to our attention that there is need of an elementary explanation of the principles and methods of stereographic projection, covering all the common applications in the field of metallography and physical metallurgy. The following contribution is an attempt to fill this need. The description of each method is supplemented with references to publications in which the method has been used. For convenience to the reader, these illustrative references are chiefly in American journals, particularly the publications of the American Institute of Mining and

Jan 1, 1937

By Robert E. Green, Edmund G. Henneke

Expressions are derived for the orientation factors associated with dislocation damping due to dislocation motion in the basal slip plane. The results of the calculation of these factors for zinc crystals aye pvesepzted and the relevance of these results to ultvasonic-attenuation measuvements is discussed. In this paper expressions are derived for the orientation factors associated with damping of sound waves due to dislocation motion in the basal slip plane of hexagonal crystals. For zinc crystals, the orientation factors for dislocation motion in one slip direction only, as well as for simultaneous motion in all three basal slip directions, have been calculated at 1-deg intervals. The results of these calculations are presented in the form of contour diagrams in a sector of a standard polar coordinate graph. The calculations have been carried out for both the traveling- and the standing-wave conditions. The relevance of these results to ultra sonic-attenuation measurements is discussed. Associated with the calculation of the orientation factors, the modes of elastic-wave calculation were also evaluated, according to the procedure previously employed by Hinton and Green.' The results of these calculations are not presented here since similar results have been reported earlier by Mus-grave.2 However, it should be mentioned that, although the qualitative features of Musgrave's results are preserved, the quantitative values are somewhat altered since different values for the elastic constants of zinc were used. ORIENTATION FACTORS It is convenient to refer to three different sets of coordinate axes, Fig. 1, in the following calculations. First, there are the Miller-Bravais axes which are used in describing the Miller-Bravais indices of planes and directions in a hexagonal crystal. These axes are denoted in the conventional manner by a,, a,, a,, and c. The second set of axes used is a rectangular Cartesian coordinate system located as shown in Fig. 1. Note that the x axis coincides with the close-packed direction al [2110], the z axis coincides with the c axis [0001], and the y axis is orthogonal to these two lying in the [0110 ] direction. Finally, a form of Eulerian angles is used to locate the position of the specimen axis. The angle between the specimen axis and the c axis is denoted by 0 and the angle between the projection of the specimen axis on the basal plane and the a, direction is denoted by ø. The majority of observations on plastic deformation of metal crystals indicates that such deformation is caused by the motion of dislocations on a limited number of crystalline planes and in a close-packed direction. In crystals with hexagonal symmetry the most prominent slip plane is the basal plane (0001) and the slip directiops- are one of the close-packed directions, [2110], [ 12101, or [ 1120]. To properly set the stage for the following work, several points must be clarified. First, we want to consider the contribution to the attenuation of elastic waves by dislocations only. While the Granato-Lucke, model for dislocation damping is presently the one most quoted, it is not necessary to refer the present work to it. The only assumption that need be made is that the motion of dislocations absorbs energy from the elastic wave and therefore attenuates it. It is immaterial here how this energy absorption occurs. However, because dislocations have been observed to move most freely on the (0001) plane for hexagonal crystals undergoing plastic deformation, it will be assumed that it is the dislocation motion on this plane which attributes to the observed attenuation. The basic orientation factor, Ok, is essentially the same as that used by Green and Hinton for fee crystals,4 defined by the equation

Jan 1, 1968

By W. L. Fink, R. S. Archer

This paper describes results obtained on aluminum-beryllium alloys and aluminum-beryllium-copper alloys in the preparation of which aluminum of 99.95 per cent. purity was used. The constitution and structure of the high purity binary alloys are given. The aluminum-beryllium eutectic occurs at 0.87 per cent. beryllium and 645° C. The solid solubility of beryllium in aluminum at 631° C. is 0.05 per cent, beryllium, and at room temperature is less than 0.013 per cent. beryllium. The densities of the alloys are substantially the same as the values calculated on the assumption that the densities of the elements are not changed by alloying. All of the alloys age-harden at room temperature after a solution heat treatment, and the chill cast aluminum-beryllium-copper alloys age-harden at room temperature without a prior solution heat treatment. Hardness and tensile properties are given. Salt spray corrosion tests on sheet specimens are described. It is shown that beryllium docs not lower the corrosion resistance of aluminum to salt spray provided the alloy has received a solution heat treatment. Commercial Possibilities of Beryllium Alloys Beryllium has certain properties such as low density, high hardness, good corrosion resistance, low thermal expansion and fairly good electrical conductivity, which would indicate that it is worthy of consideration as an ingredient of light alloys. It was not until recently, however, that beryllium could be produced with sufficient ease to encourage research along this line. The production of beryllium by electrolysis from a fluoride bath has now developed to the stage where it could be used commercially if there were sufficient demand for the element. Claims made in certain newspapers and technical articles in regard to thc strength and corrosion resistance of thc aluminum-beryllium alloys are not justified by experimental results. Moreover, beryllium is an expensive metal ($200 a pound at the time this work was done) and, on account of the nature of its ore and the consequent difficulty of its extraction, it will in all probability continue to be a relatively expensive metal, although the cost would undoubtedly be a great deal less than $200 a

SUDBURY ore processed by International Nickel Co. of Canada Ltd. was recovered for many years as two mill concentrates, one primarily of copper, and the other mixed pentlandite-pyrrhotite, But, Since iron content of the nickeliferous pyrrhotite concentrate was ten times its nickel value, capacity of smelting was limited by the need for slagging the excess iron. A process for recovering the iron con- tent was developed after some years of research and a $20-million plant was constructed to employ the new method. Built near Copper Cliff, Ont., the plant started operation early in 1956, scheduled for separate treatment of 365,000 tons of pyrrhotite each year. It is only the first unit of an installation which will have a capacity of more than 1 million tons per year of pyrrhotite. By early 1958, production totaled more than 200,000 long tons of 68 pct Fe pellets containing 0.003 pct P, 1.5 pct SiO2, 0.01 pct S, and 0.15 pct Ni.

Jan 8, 1958

By Jack White

W. I. Garms-—The authors state that when they added 11 tons of balls to the 45 pct volume ball load, the power needle did not budge. The question arises as to whether any increase in capacity accompanied the 11-ton addition. It is hardly conceivable that all of the balls making up the l l-ton addition were sterile. However, as the work done in the ball mill is not by kilo-watthours per se or balls per se but by kilowatthour-balls, it is possible that the kilowatthourballs in the mill before the ll-ton addition had a different amperage, voltage or robustage than those in the mill after the addition and that the overall outcome was that equal work was done before and after the addition. The authors can keep the efficiency that they got with the 45 pct volume 1-in. ball charge and get additional capacity by putting more kilowatthourballs to work in the form of the addition of 11 tons of 2-in. balls to the present ball charge, and subsequent makeup additions by weight of 20 pct 2-in. balls and 80 pct 1-in. balls. J. F. Myers (authors' reply)-—Mr. Garms points his finger at the 11 tons of "sterile" balls added to the Tri-cone mill. A fact so interesting to us that we felt it should be reported. Clearly, ball slippage at the existing mill speed prevented any further transfer of power from the shell to the ball mass. We agree that the kilowatthourballs would increase, were we charging rough 2-in. balls as suggested by Mr. Garms. The assumption is, of course, that we would get a corresponding increase in work done. Our reported data (CIME meeting, Vancouver, 1946) shows a gain of work accomplished of 7.6 pct as we decreased the ball size from 2 in. to 1% in. and a further gain of work accomplished of 2.1 pct when we went from 1 % in. to 1 in. The small ball results reported by H. R. Banks at Chapman Camp are also very convincing. In the case of 2-in. balls they would take the conventional ball path and start cascading. They would thus destroy the classifying pool over the "foot" of the

Jan 1, 1951

By Jack White

W. I. Garms-—The authors state that when they added 11 tons of balls to the 45 pct volume ball load, the power needle did not budge. The question arises as to whether any increase in capacity accompanied the 11-ton addition. It is hardly conceivable that all of the balls making up the l l-ton addition were sterile. However, as the work done in the ball mill is not by kilo-watthours per se or balls per se but by kilowatthour-balls, it is possible that the kilowatthourballs in the mill before the ll-ton addition had a different amperage, voltage or robustage than those in the mill after the addition and that the overall outcome was that equal work was done before and after the addition. The authors can keep the efficiency that they got with the 45 pct volume 1-in. ball charge and get additional capacity by putting more kilowatthourballs to work in the form of the addition of 11 tons of 2-in. balls to the present ball charge, and subsequent makeup additions by weight of 20 pct 2-in. balls and 80 pct 1-in. balls. J. F. Myers (authors' reply)-—Mr. Garms points his finger at the 11 tons of "sterile" balls added to the Tri-cone mill. A fact so interesting to us that we felt it should be reported. Clearly, ball slippage at the existing mill speed prevented any further transfer of power from the shell to the ball mass. We agree that the kilowatthourballs would increase, were we charging rough 2-in. balls as suggested by Mr. Garms. The assumption is, of course, that we would get a corresponding increase in work done. Our reported data (CIME meeting, Vancouver, 1946) shows a gain of work accomplished of 7.6 pct as we decreased the ball size from 2 in. to 1% in. and a further gain of work accomplished of 2.1 pct when we went from 1 % in. to 1 in. The small ball results reported by H. R. Banks at Chapman Camp are also very convincing. In the case of 2-in. balls they would take the conventional ball path and start cascading. They would thus destroy the classifying pool over the "foot" of the

Jan 1, 1951

By Carel Robinson

MECHANIZATION of coal mine, is radically changing the requirements for under-ground transportation. It has increased materially the need for reliability and belt conveyors are the most dependable means of moving coal away from the place where it is mined. Their record of freedom from delays is almost 100 per cent. Why then are- not belt conveyors in more general use. Part of the answer lies in the pour records made at some of the earlier installations, and in the fact that belts have so long been identified as a type of equipment suitable, in the main, only to thin seams. Another reason is lack of knowledge of the full potentialities of belt transportation.

Jan 1, 1941

By H. E. Hostetter

Grossmann's method1 for calculating the hardenability of steel from the composition and grain size has gained wide acceptance, and when properly used, has been well proved in practical application, both for estimating the hardenability of known compositions and for selecting compositions to meet known hardenability requirements. The Grossmann method uses as the criterion of hardenadility the "ideal critical diameter," DI, which is the' size round that will just harden to a structure of 50 per cent martensite at the center when given the theoretically fastest quench, or "ideal quench." The DI can be related to actual quenching practice if the severity of quench is known; or the DI can be correlated with hardenability as determined by the Jominy end-quench method.2 The effect on hardenability of each element present in a steel can be represented by a multiplying factor, the value of which depends on the amount of the element present and the degree of effectiveness of the particular element. (The value of the factor for a given carbon content varies with the grain size.) When the factors for all elements present in a steel have been determined from charts, they are multiplied, and the resultant product is the DI of the steel. The validity of Grossmann's scheme of multiplying factors has been confirmed in a number of other investigations.3-6 It can be appreciated that a certain desired level of hardenability can be obtained by adding chromium, molybdenum, nickel and vanadium to a base composition containing carbon, manganese, silicon and the usual impurities. Many of the ranges of hardenability used commercially can be obtained by any of the foregoing alloying elements used singly in the base composition. The same hardenability levels also can be obtained through use of any of a great number of multiple element combinations of these alloying elements. In this report a method will be presented for determining what one combination is the most efficient (based on hardenability and cost of added alloy) for a given level of hardenability. It should not be assumed from the emphasis given to hardenability, that hardenability is the only criterion for the selection of an alloy composition. Such properties as the hot-working characteristics, machinability, carburizing characteristics, amount of distortion during quenching and the retention of austenite may be considerations of importance in many applications. However, hardenability is one of the most important properties of an alloy steel and one that must be considered in almost all cases involving heat-treatment by quenching. Therefore, a method for determining the lowest-cost alloy combination should be of considerable value. Determination of Most Efficient Combinations For comparing the alloying elements on standards of cost and hardenability, it

Jan 1, 1947

By Donald W. Scott, Nathaniel Arbiter, A. C. Richardson

This paper describes the application of amine flotation to a specific problem—that of increasing the grade of magnetite concentrates derived from an iron ore requiring extremely fine grinding for mineral liberation. Experiments conducted on an iron ore from Wisconsin had shown that concentrates containing 60 to 62 per cent iron and 12 to 14 per cent silica could be produced by magnetic separation. The residual silica occurred as quartz and hornblende, either entrained or locked with magnetite. Most advantageous utilization of the concentrate, however, necessitated that the silica content be reduced to about 5 per cent, equivalent to an iron content of 67.5 per cent. It had been demonstrated that tabling of the magnetic concentrate removed sufficient quartz and hornblende to yield an acceptable concentrate, but disadvantages inherent in tabling dictated that flotation be investigated as a substitute. The goals set for the flotation investigation were: (I) the production of concentrates of about 68 per cent iron content from the magnetic concentrate; (2) an iron recovery of about 85 per cent of that in the feed to flotation; and (3) minimum reagent cost. Both batch and continuous flotation tests were employed; the former, to establish the procedure and the latter to verify it. Although the data were obtained on a specific ore, and with a commercial application in view, it is believed that they have a bearing on other problems where amine flotation is being used or is anticipated. Samples Two samples, designated "(minus 100-mesh magnetic concentrate" and "minus 150-mesh magnetic concentrate," were used for the batch experimental work. They differed only in the degree to which the crude ore was ground prior to magnetic separation. They were stored moist in steel drums in quantities sufficient for all the experimental work reported. This procedure had the advantage of allowing all tests to be made on common samples, but had the disadvantage that the individual flotation samples, because of the difference in storage time, were subject to various stages of surface alteration. Previous work had indicated that common samples were desirable for the batch studies, and it was decided that if these data appeared sufficiently promising the effect of surface alteration could be checked best by continuous tests. The size distributions and the assays of the samples are given in Table I. The minus 150-mesh magnetic concentrate, on which most of the flotation tests were made, assayed 60.9 per cent iron, 13.3 per cent silica, and 0.016 per cent phosphorus. The minus 325-mesh portion represented 78.I per cent of the sample by weight, and assayed 67.9 per cent iron. Thus, the insoluble, mainly silica, was concentrated

Jan 1, 1947