Search Documents

By W. L. Hill, W. H. Armiger, S. D. Gooch

The physical properties, chemical behavior under thermal treatment, and fertilizer value of fluorine-containing pseudowavellite (hydrous calcium aluminum phosphate) that occurs as phosphate clay admixed with quartz sand in an extensive deposit near Bartow, Fla., were determined by experiments in laboratory, pilot-plant, and greenhouse. When the mineral was heated at 500°C, 80 pct of the phosphorus became citrate soluble. The heated product, however, deteriorates markedly under moist conditions such as obtain in the soil.

Jan 1, 1950

By W. A. Wall, R. L. Kidd

IN present-day flotation practice, grinding of the flotation feed is carried to extremely fine sizes, 70 to 80 per cent minus 200 mesh being customary. The greatest flotation losses occur in the coarsest and finest sizes, but the losses in the very fine sizes are, of course, much the more important because of the large proportion of fines in the feed. These losses are particularly high in zinc ores so a study of the effect of size on the flotation of sphalerite has been made. The mineral used in these experi¬ments was a pure sphalerite, especially free from copper, from the Joplin district in Missouri. The sizes coarser than 200 mesh were separated by screening, the sized mineral then being deslimed on a Wilfley table. The sizes finer than 200 mesh were obtained by water elutriation as described by H. R. Bradford (M. S. Thesis, University of Utah, 1932) ; particles finer than 6.5 microns could not be obtained with the apparatus used.

Jan 1, 1933

By William H. Spice

The area on which oil and gas development is reported covers 30 counties, which are included in the Texas Railroad Commission's District No. I. This area not only includes the old established Balcones fault-line group of producing fields but also includes the southwest extension of this trend and some of the deeper Wilcox (Eocene) exploratory development. (Fig. J.) In the old Balcones fault-line zone, three new fields were discovered during 1941. These fields are comparatively small, producing from Dale limestone or Austin chalk. No new fields were discovered during the year in the Edwards (Lower Cretaceous) limestone horizon. One new shallow field was discovered in the Reklaw (Eocene) sand horizon and, in the southwestern part of the district, one oil field and one gas field were discovered in the Navarro (Upper Cretaceous) sand horizon. An extremely important extension was made to the one producing Wilcox (Eocene) field of the district in the Washburn Ranch field of La Salle County. The district produced 6,650,357 bbl. during 1941, which was a 12 per cent decrease under production for 1940. Approximately 4,954,000 bbl. of this total production was produced by the three Edwards limestone fields, Luling, Salt Flat and Darst Creek, the remaining production coming from the other 43 active fields in the district. In all, 3694 wells were producing at the end of 1941, compared with 3559 wells at the end of the previous year. During the year, 139 new producing wells were completed and 29 wells were abandoned in the producing fields. The increase in producing wells represents an increase in new wells over abandonments in these fields, together with a decrease in wells temporarily shut down as of the end of 1941. The majority of production drilling was carried on in the following fields; Bee Creek, Chicon Lake, Elm Creek, Gas Ridge, Pearsall and Tenney Creek. Approximately 250 wells were drilled during 1941, of which 110 were exploratory wells completed as failures throughout the district. Considerable exploratory work was continued during 1941 along the Wilcox trend. Geophysical work employing various types of geophysical methods and leasing activity was continued along this trend, particularly by the major companies. The significance of this activity is apparent from the successful extension and development in the Washburn field of La Salle County, where several well-developed gas-and-oil producing horizons have been developed in the lower Wilcox section between 5100 and 5600 ft. as noted in the following paragraphs. Continued exploratory activity along this general trend as far as present conditions will permit is predicted for 1942. New Fields Elgin Field, Bastrop County.—No. I-A Hiram Walker, Marts and Beaven, Inc., discovery well of the Elgin field, was com pleted on Apr. 22, 1941, in broken Austin chalk from 2820 to 2840 ft., pumping 105 bbl. per day, 36.8°A.P.I. gravity. The well apparently is producing from a crevice in

Jan 1, 1942

By William H. Spice

The area on which oil and gas development is reported covers 30 counties, which are included in the Texas Railroad Commission's District No. I. This area not only includes the old established Balcones fault-line group of producing fields but also includes the southwest extension of this trend and some of the deeper Wilcox (Eocene) exploratory development. (Fig. J.) In the old Balcones fault-line zone, three new fields were discovered during 1941. These fields are comparatively small, producing from Dale limestone or Austin chalk. No new fields were discovered during the year in the Edwards (Lower Cretaceous) limestone horizon. One new shallow field was discovered in the Reklaw (Eocene) sand horizon and, in the southwestern part of the district, one oil field and one gas field were discovered in the Navarro (Upper Cretaceous) sand horizon. An extremely important extension was made to the one producing Wilcox (Eocene) field of the district in the Washburn Ranch field of La Salle County. The district produced 6,650,357 bbl. during 1941, which was a 12 per cent decrease under production for 1940. Approximately 4,954,000 bbl. of this total production was produced by the three Edwards limestone fields, Luling, Salt Flat and Darst Creek, the remaining production coming from the other 43 active fields in the district. In all, 3694 wells were producing at the end of 1941, compared with 3559 wells at the end of the previous year. During the year, 139 new producing wells were completed and 29 wells were abandoned in the producing fields. The increase in producing wells represents an increase in new wells over abandonments in these fields, together with a decrease in wells temporarily shut down as of the end of 1941. The majority of production drilling was carried on in the following fields; Bee Creek, Chicon Lake, Elm Creek, Gas Ridge, Pearsall and Tenney Creek. Approximately 250 wells were drilled during 1941, of which 110 were exploratory wells completed as failures throughout the district. Considerable exploratory work was continued during 1941 along the Wilcox trend. Geophysical work employing various types of geophysical methods and leasing activity was continued along this trend, particularly by the major companies. The significance of this activity is apparent from the successful extension and development in the Washburn field of La Salle County, where several well-developed gas-and-oil producing horizons have been developed in the lower Wilcox section between 5100 and 5600 ft. as noted in the following paragraphs. Continued exploratory activity along this general trend as far as present conditions will permit is predicted for 1942. New Fields Elgin Field, Bastrop County.—No. I-A Hiram Walker, Marts and Beaven, Inc., discovery well of the Elgin field, was com pleted on Apr. 22, 1941, in broken Austin chalk from 2820 to 2840 ft., pumping 105 bbl. per day, 36.8°A.P.I. gravity. The well apparently is producing from a crevice in

Jan 1, 1942

By Warren B. Weeks

The year 1940 saw an increase of 20 per cent in oil production over the previous year—compared with a 16 per cent increase the previous year. In all, 25,790,380 bbl. were produced, an increase of 4,414,150 bbl, over 1939 and the largest production figure for south Arkansas since 1928. The older settled production continued to decline. Magnolia accounted for most of the increase, with aid from the other recent deep fields. During the year, 169 wells were drilled, 79 fewer than in the previous year. Of 131 wells drilled in proven fields, 18 were dry. Three of the 38 wildcats were pool openers. The drilling depth record was increased from 9028 to 9550 feet. Trend of Prospecting For the first time since 1936, the search for oil in the deep Smackover limestone slackened perceptibly; g dry wildcats ended in Smackover, 2 in. the underlying Eagle Mills; 7 penetrated Paleozoic beds, while 9 ended in Hosston, 2 in Glen Rose, 2 in Paluxy and 4 in Gulf. Geology The wells listed in Table 2 either resulted in the discovery of new oil pools or, because of their depth or location, afforded impor-tant stratigraphic or structural informa-tion. Fig. I is a general columnar and stratigraphic section showing the relation-ship of the strata within the Comanche series. The nomenclature shown was ac-cepted by the Shreveport Geological Society. It was subsequently published by Imlay,l who indicated probable correlations with other areas and presented evidence for the possible Jurassic age of the under-lying Cotton Valley and Smackover formations. New Fields Pouke.—On June 10, 1940, the Louark Producing Co. completed its No. I Sturgis, sec. I, T. 17 S., R. 27 W., in central Miller County, producing between 3583 and 3607 ft. in the upper part of the Paluxy forma-tion. The well flowed I00 bbl. of 3r.4' gravity oil per day through Ns-in. tubing choke. This discovery resulted from seismograph work. Six other wells were drilled in the area, none of which found production in the original sand. One of these wells is producing from a sand 50 ft. deeper in the section. The others were abandoned. No further development is in prospect. Production is from lenticular sands of the upper Paluxy; 45,556 bbl. had been pro-duced by the end of 1940. There is structural closure against a fault to the northwest. McKanzie.—The Atlantic Refining Com-pany's No. I Bodcaw Lumber Co., sec. 29, T. 17 S., R. 23 W., eastern central La-fayette County, was completed June 8, 1940, as the eighth and farthest west of the Smackover (Reynolds o6lite) limestone pools. The well flowed 10 bbl. an hour of 58.6' gravity distillate through an 1 1/64 Ma-in. tubing choke, with a gas-oil ratio of 8400:I.

Jan 1, 1941

By Warren B. Weeks

The year 1940 saw an increase of 20 per cent in oil production over the previous year—compared with a 16 per cent increase the previous year. In all, 25,790,380 bbl. were produced, an increase of 4,414,150 bbl, over 1939 and the largest production figure for south Arkansas since 1928. The older settled production continued to decline. Magnolia accounted for most of the increase, with aid from the other recent deep fields. During the year, 169 wells were drilled, 79 fewer than in the previous year. Of 131 wells drilled in proven fields, 18 were dry. Three of the 38 wildcats were pool openers. The drilling depth record was increased from 9028 to 9550 feet. Trend of Prospecting For the first time since 1936, the search for oil in the deep Smackover limestone slackened perceptibly; g dry wildcats ended in Smackover, 2 in. the underlying Eagle Mills; 7 penetrated Paleozoic beds, while 9 ended in Hosston, 2 in Glen Rose, 2 in Paluxy and 4 in Gulf. Geology The wells listed in Table 2 either resulted in the discovery of new oil pools or, because of their depth or location, afforded impor-tant stratigraphic or structural informa-tion. Fig. I is a general columnar and stratigraphic section showing the relation-ship of the strata within the Comanche series. The nomenclature shown was ac-cepted by the Shreveport Geological Society. It was subsequently published by Imlay,l who indicated probable correlations with other areas and presented evidence for the possible Jurassic age of the under-lying Cotton Valley and Smackover formations. New Fields Pouke.—On June 10, 1940, the Louark Producing Co. completed its No. I Sturgis, sec. I, T. 17 S., R. 27 W., in central Miller County, producing between 3583 and 3607 ft. in the upper part of the Paluxy forma-tion. The well flowed I00 bbl. of 3r.4' gravity oil per day through Ns-in. tubing choke. This discovery resulted from seismograph work. Six other wells were drilled in the area, none of which found production in the original sand. One of these wells is producing from a sand 50 ft. deeper in the section. The others were abandoned. No further development is in prospect. Production is from lenticular sands of the upper Paluxy; 45,556 bbl. had been pro-duced by the end of 1940. There is structural closure against a fault to the northwest. McKanzie.—The Atlantic Refining Com-pany's No. I Bodcaw Lumber Co., sec. 29, T. 17 S., R. 23 W., eastern central La-fayette County, was completed June 8, 1940, as the eighth and farthest west of the Smackover (Reynolds o6lite) limestone pools. The well flowed 10 bbl. an hour of 58.6' gravity distillate through an 1 1/64 Ma-in. tubing choke, with a gas-oil ratio of 8400:I.

Jan 1, 1941

By Samuel H. Dolbear

THE purpose of a technical report is to record facts, usually collected by investigation, and to interpret these facts in understandable language. The audience may range from a small shareholder without technical knowledge, to a highly trained engineer or geologist. If the client is a mining company with technically trained executives, the report writer's problem is relatively simple. The writer will then be appraised not only for his conclusions, but for clarity of language and organization of the report. If the writing is bad, the construction careless, and there is a failure to clearly convey to the reader the facts and the author's conclusions, the report is a failure and the writer may have damaged his professional character. Spoken words die quickly, written words may constitute a permanent record and if they are badly composed they may rise up to damn the author. "A good measure of an author's understanding of his subject is his ability to express it clearly in plain words." Good English Teachers in the fields of mineral technology have frequently complained that even in post-graduate groups there is an appalling indifference to their appeals for good English. Some have even noted a student's belief that the use of refined English is effeminate. If those with such immature beliefs could measure the pay-check damage arising from the use of "sloppy" language, they would realize that precision and refinement in English may be quite as important as technical accuracy. When the reader audience is without technical knowledge simplicity in treatment becomes especially important. If one is engaged in consulting work, in government service, or in any field where reports have public distribution, the language employed should be technically adequate but simple enough to be understood by non-technical readers. For example, one may use the term "visual" in place of "megascopic." Technical language can be so obscure that it cannot be understood even by highly-trained students. In the March-April (Vol. 47-No. 2) issue of Economic Geology, Nicholas Vanserg ridicules these extremes and quotes various paragraphs from published material, such for example: "However, lattice orientation unaccompanied by cognate dimensional orientation can never be attributable to growth from an isotropic blastetrix." "The temperature declines because of cessation of the exothermic chemical and mechanical equilibriopetal processes." These he calls "good geologese" and they are calculated not only to baffle the reader but to impress upon him the erudite character of the author. Revision In some cases, difficulty arises from the fact that the writer is too close to the subject and unconsciously assumes that his reader is equally familiar with the background of the report. It is difficult for the writer to regard his work objectively and to determine to what extent it is likely to be understood. Every important manuscript will gain in clarity if the author will have it reviewed by an informed reader. But the writer must not be oversensitive to criticism and should not treat his composition as perfect and beyond the possibility of improvement. The first draft of a report always requires revision, regardless of the care used or the ability of the writer. Three or four revisions are not uncommon. The first draft usually requires expansion in places, the deletion of non-essential material, and language changes to promote clarity of expression. This should be done by the author after a lapse of time, even if only overnight, in which his mind has been occupied on some other subject. Possible improvements are always more visible. The manuscript should be passed on to another reader for further suggestions. Organization of Material The engineer should study available reports and library references before going into the field. If the previous reports have been responsibly done and can be accepted as correct, then much field time can be saved. It is, of course, customary to make some on-the-ground checks to confirm earlier reports, particularly those relating to ore reserve which may have undergone changes. Report writing requires time and expense, but nevertheless, the basic reasons for conclusions should be presented even in the case of a worthless property, for it may prevent a duplication of the work. If the mine examined is obviously of no further interest, no useful purpose can be, served by preparing a report in detail. In one case an engineer travelled all the way to South America only to find that the mine had been grossly misrepresented and was valueless. His cabled report "Nonsense" is a case of over-simplification, but it served his company's purpose. The first step in report organization should be the selection of subjects. This should be done at the mine, and the data collected for each subject should be reviewed in considerable detail on the ground. Otherwise one may find that he has failed to collect some essential details not readily obtained after he has returned to headquarters. If the property to be described is undeveloped, then many of the subject titles are automatically eliminated. Usually no useful purpose is served by an attempt to calculate the cost of production under such circumstances, although the cost of exploration

Jan 1, 1952

By H. H. Campbell

The following paper deals almost exclusively with the results of practice at the works of the Pennsylvania Steel Company at Steelton, Pa. From the records of the furnaces at this plant, both acid and basic, large and small, are drawn the data for the various demon strations, and on a long and intimate experience with their opera tions are founded many theories and generalizations. It may seem that universal laws should not be built upon a basis so restricted ; but in reality the condition is the strongest guarantee of validity. Each table investigates some- certain variable, and by virtue of the common origin of the factors, we have good ground for assuming the corresponding agents to be equal. The examples may or may not be instances of good practice, and may be open to criticism if regarded solely as exponents of • metallurgical success. But it must be remembered that the lists are not made up of selected specimens, nor are they chosen to show su perior results; they are gathered to investigate, by strict scientific methods, the formula? of the operation. In such work no untoward results should be eliminated, save those which bear upon their face the stamp of experimental error. If the worst members be omitted, then the best must also be omitted. Only by using every available case can an honest attempt be made to deduce a true average. It is recog nized, however, that with the most careful selection it is difficult, if not impossible, to collect data representing universal conditions. In each table the records tell of a special practice, and all conclusions drawn from them are true only within the limits between which the equations have been integrated. Not assuming the prerogative of speaking for American melters in all the opinions herein expressed, nor acting as a camera in por traying an ephemeral state of national metallurgical development,

Jan 1, 1894

Last October a committee was appointed by The War Service Association of Manufacturers of Solder and Bearing Metals, Inc. to consider the report of the U. S. Bureau of Standards to the Conservation Division of the War Industries Board, a letter of the War Industries Board, and the discussions of this letter as reported at the meetings of association and to summarize the information thus obtained. The report of this committee has just been printed. The committee agrees with the Bureau of Standards that 99 per cent. tin can be used. It also finds that a very small amount of lead might increase the tendency of the bearing to crack and that lead has a hardening effect on babbitts up to a possible limit of 10 per cent. of lead. Still in the so-called genuine babbitts, in the presence of lead a certain proportion of low melting point eutectic is introduced which admits of the bearing being poured into thinner sections and is decidedly advantageous in the die-casting process in producing a much smoother casting. But the committee recommends that the Bureau of Standards thoroughly investigate this point. Lead-base babbitts, to give satisfactory service, must be carefully made of the proper raw materials. The bronze hearing that has been thoroughly tinned and containing the thinnest possible babbitt lining is now becoming recognized as the ideal bearing. The compositions, recommended by the committee are as follows:

Jan 2, 1919

By Frederick Laist

I AM APPRECIATIVE of the honor you have done me in electing me to membership in your Society. I value the contacts with men of imagination and ideals which this implies. I am grateful for the recognition of such small contributions as I may have made, or helped to make, to the vast fund of scientific and engineering knowledge. We like to think, as we grow older, that our lives have not been purely parasitical, and that through our efforts some forward step, however small, has been taken toward improving conditions under which we live and do our work. In these days of industrial depression, we hear much criticism of our "machine age." Modern engineering, mass production, the complexity of our lives, all come in for some share of blame. The farmer is said to have been spoiled by the tractor and the gang plow, the factory worker has become a slave of the assembly conveyor, the scientific worker is no longer free but has sacrificed much of his individuality to the research organization of which he is a part. We wonder whether our work as engineers has been worth while and whether our striving after more efficient ways of doing things has been a curse to mankind rather than the boon we thought we were conferring.

Jan 1, 1932

D. M. Riordan has been appointed a member of the Institute Com¬mittee of the Engineers' Reserve Corps movement. Our Committee, therefore, now consists of Henry S. Drinker, Chairman, Messrs. Arthur S. Dwight, Warren A. Wilbur and D. M. Riordan.

Jan 1, 1916

By W. W. Gorr, R. Smith, E. H. Wyche

THE combination of high strength and corrosion resistance of cold-worked 18 Cr, 8 Ni steel has been advantageously utilized for some time, particularly in aircraft and rail car structures. There are, however, certain limitations on the use of such materials because the high strengths can be obtained only by cold-working, limiting the available products to sheets, strip, wire and tubes. The authors sought to overcome these limitations by resorting to precipitation-hardening, which has been used so successfully in nonferrous metallurgy but only to a limited extent in iron-base alloys. Accomplishment of this objective not only overcame the limitations, but also effected certain improvements in mechanical and other properties. This paper is an account of the development by Carnegie-Illinois Steel Corporation of a precipitation-hardening 18-8 stainless steel (called Stainless W? and tentatively identified as type 322). A description is given of its composition and metallurgical characteristics, heat-treatment, physical and mechanical properties and corrosion resistance. DEVELOPMENT OF THE NEW STEEL For a considerable length of time the authors were unable to determine the mechanism of the precipitation-hardening process that had been noted by Ffield 18,19 in 18-8 Ti or 18-8 Cb after cold-working and reheating to moderately elevated temperatures. All known variables were exhaustively studied, but with little success. However, results began to indicate that chemical composition was the most important variable, particularly the ratio of austenite-forming to ferrite-forming elements. The investigators 'then focused their attention upon the composition, and, in particular, upon the element titanium and its mode of alloying in the presence of other elements. A heat was obtained that could not be brought to the softness level of annealed 18-8. The response to cold-straining and aging* was very marked by previous standards, and, more important, cold-straining was found to be entirely unnecessary to produce the precipitation-hardening effect. The chemical composition of this heat was: C, 0.06 per cent; Mn, 0.54; P, 0.016; S, 0.016; Si, o.58; Ni, 7.28; Cr, 17.6o; Ti, 0.90; Al, 0.17. For some time the development work, particularly on composition, was carried

Jan 1, 1946

By M. G. Corson

The iron-silicon alloy series has always been one of the most puzzling among the binary alloys. Examining the well-known mechanical properties of the iron-rich alloys only we meet the following situation: The ultimate strength and yield point of alloys worked and annealed under the usual conditions represent nearly a straight line function of the silicon content up to 1.5 per cent. silicon (Fig. I). Starting at the ultimate strength of 35,000 lb. and at a yield point of 16,000 lb. for pure electrolytic iron, one reaches a maximurn strength of 93,000 lb. and a maximum yield point of 74,000 lb. at 4.5 per cent. silicon. This corresponds to an increase in ultimate strength by 13,000 lb, per each per cent. of silicon added and nearly the same rate applies to the yield point. The data mentioned are taken from the investigation by T. D. Yensen,1 and while they do not exactly corroborate the results obtained by earlier investigators, they seem to be the most correct. Plastic properties of the alloys are controlled by a much more complicated relationship. Up to 2..5 per cent. Si, the elongation stays close to 50 per cent. (in 2 in.) and the area reduction amounts to 85 per cent., a situation that forms the usual feature of all alloys representing strictly solid solutions. The plasticity of the latter is always nearly equal to that of their base metal. Beyond 2.5 per cent. silicon, the situation becomes much more complicated. Yensen observed an enormous drop in elongation and area reduction at about 2.65 per cent. silicon, where the first hardly reaches 10 per cent. and the second is still lower; he found, however, a considerable recovery in plasticity at about 2.8 per cent. Si and up to 1.5 per cent. Si it is represented by 20 per cent. for the elongation and 30 per cent. for area reduction. Yensen's graphs, as shown in Fig. 1, indicate also a considerable drop in strength and yield point at the same point of 2.65 per cent. Si,

By R. H. SWEETSERS

A Discussion of Mr. Hall's paper, read at the Washington Meeting, February, 1905. R. H. SWEETSER, Sault Ste. Marie, Ont. (communication to the Secretary*) :-The recent work of furnace No. 1 of The Algoma Steel Co., at Sault Ste. Marie, Ontario, using for fuel, first all charcoal, then a mixture of charcoal and coke, and finally all coke, upsets the estimates given by Mr. Hall in the last two paragraphs of his interesting paper. Furnace No. 1 was built for a charcoal-furnace, and it was run on charcoal fuel from March 6 until July 9, 1905; then, for a week, a mix¬ture of charcoal and coke was used, and, since then, coke alone has been the only fuel. It is to be regretted that at no time, during the run on charcoal, was there enough charcoal on hand and " in sight'" to warrant blowing the furnace as hard as it should have been blown. During April and May the supply of charcoal limited the amount of blast to about 8,000 cu. ft. of air per min.; in June, to about 8,900 cubic feet. For a few days in July about 10,000 cu. ft. were blown, and then the maximum daily output, 173 tons (2,240 1b.), was reached. At all times the quality of the charcoal was poor, having been made from wood cut from three to four years before. Doubtless this furnace could have produced .200 tons of iron per day, even with this quality of charcoal, provided the supply had been sufficient; and with good charcoal I see no reason why it could not make as much iron per day as it has made with coke. During the one week of using a mixture of charcoal and coke, the changes in quantity of blast and composition of the slag followed each other so closely that no single condition could last long on the furnace. The results were good, and the pig-iron was about the same in quality as that made during the

Jan 1, 1906

By J. C. Purcupile, R. L. Morris

Present methods of roof support require that first a hole must be drilled, and then a toggle belt or grouted resin bolt be set. Automating this system is very difficult. Therefore, we decided to develop a system which would insert pins into the roof in one step. We think that this type of system can be automated much easier. It would then speed up the roof bolting operation and eliminate the need for a man to work under unsupported roof, making roof bolting a much safer job. There are two ways that a pin can be inserted in a mine roof without drilling a hole. It can either be pushed in, using a very high, constant axial force; or it can be hammered in like a nail. The former method involves very high compressive stresses in the pin, and requires complicated machinery to prevent buckling. Since hammering the pin does not require high axial forces buckling is not as likely. Also, experiments have shown that there are no problems associated with getting the pin to go in straight. We chose to develop the second method. While investigating methods for hammering a pin into a mine roof, we learned that piles were being driven 10 times faster than by conventional methods with a method called "orboresonance." We decided to turn the pile driver upside down, and drive pins up into the mine roof. Sonic Pin Setting Machine The machine consists of a steel bar supported at the nodal points of its first mode of transverse vibration (Fig. 1). A mechanical oscillator, driven by a hydraulic motor, is attached to one end of the bar. This provides the forcing function for the vibrations in the bar. The hydraulic power is supplied by a portable unit. When the forcing function is near the natural frequency of the bar, large amplitudes of vibration occur and require little power input. An anvil is attached to the bar at a point of maximum deflection, providing a means for striking the pin. Since the bar is being driven near its natural frequency, it takes little energy to accelerate the bar back and forth between each hit. This means that most of the power being put into the bar is going into driving the pin. This is unlike conventional pile drivers which use most of their power to accelerate the hammer back and forth between hits. The resonant frequency of the bar we used is about 250 Hz, which is in the audible range, hence the term "sonic pin setting machine." The system benefits are: (1) elimination of the two-step drilling and pin-setting roof bolt operation, (2) increased speed, (3) more intimate contact between the formation and bolts, (4) less expensive roof bolts, (5) higher integrity, (6) potential for automatic operation. Modifications During the months from Oct. to Dec. 12, 1974, under U.S. Bureau of Mines grant No. 00144104, "Projects on Coal Extraction," six members of the senior class at Carnegie Mellon University designed and built the experimental machine. They drove three pins into the Safety Research coal mine at Bruceton, Pa., and determined that the project was worth continuing. In January 1975 we began making modifications and repairs in preparation for a more extensive program of testing at Bruceton. The major items were: 1) Design and build a collapsible pin guide to keep the pin parallel with the line of travel of the lift table. 2) Move the anvil to the center of the bar. 3) Refinish the nodal holes and install new node pins and bushings. 4) Realign the bar in its frame. 5) Install a relief valve on the lift unit to control the upward force. The upward force that we exert on the pin is relatively small, so there is no tendency for it to buckle. This means that all we need to do is hold the pin straight during its initial penetration. This allows the bushing to travel up and down in a straight line. At the beginning of penetration, the bushing

Jan 1, 1977

By H. M. Howe

THIS paper presents an experimental verification of some of the predictions made by one of us' concerning 'the influence of certain conditions of casting upon the size and position of the pipe', and the position of the segregate, in steel ingots. The predictions which we have been able to verify are the following A. That the pipe is shortened and the segregate raised 1. By slow casting; 2. By casting with the large end up instead of down; 3. By retarding the cooling of the top, e.g., by means of a sinking-head. B. That the pipe is shortened by slow cooling. C. That the pipe and segregate lie in the last freezing-part. Our procedure was to cast ingots of wax (commercially pure stearic acid) containing a little bright green copper oleate (usually 1.5 per cent.) under varying conditions; to saw each ingot open along a longitudinal plane passing through its axis ; and to examine the longitudinal section thus laid bare. In order to make the segregate or enriched part more distinct in color from the impoverished part, a very little red cerasine was added. An experiment which will be described later showed that the cerasine itself does not segregate markedly, if at all. Hence we may assume that the strong contrasts between the green and red shown in so many of our ingots are due, not to segregation of cerasine, but to that of the green oleate, in the wax which in itself is uniformly reddened with cerasine.

Jul 1, 1907

By W. C. Ellis, E. S. Greiner, M. E. Fine

C. H. Samans and W. R. Ham (Chicago, Ill., and Dix-field, Maine, respectively)-—For several years we have been studying transitions of this basic type in metals, alloys, glasses, etc. Usually, however, they are not so clearly marked as those which the authors have found, and hence are much more difficult to determine accurately. Since our studies indicate that most of them occur virtually unchanged (as far as temperature is concerned) regardless of the form in which the element appears, we believe that they are a characteristic of the atom. Specifically, we believe that there is an additional rotational degree of freedom possessed by the nucleus which has not been considered heretofore. This nuclear rotation is made up of several components, each related to the several quantum shells of electrons. In chromium there are four of these shells and hence four separate series of characteristic transition temperatures. The lowest temperature at which any transition occurs, based on the present state of our computations, is 125°K, 4° higher than the authors' value of 121°K. A convergence of this series, we believe, shows up at the higher temperature of 2085 °K, surprisingly close to the transformation temperature of 2103°K recently announced by N. J. Grant of M.I.T. for a body-centered to face-centered transformation in chromium. Likewise, our computations indicate a temperature of 311°K for the second transition temperature, reported by the authors as 310 °K. A convergence of this series, we believe, shows up at a higher temperature as the melting point at 2163°K. Although our work on these series must, in a sense, still be regarded as empirical, since we do not understand fully as yet just what the series mean, it is based on a reasonably firm picture. The individual constants, from which the various series are computed for each element, comes directly from the X-ray K absorption limit. Furthermore, the same basic method has accounted for transformation and melting temperatures in about 50 of the chemical elements, which is all we have tried thus far. In many cases the only known transformation is the melting point, but in others the occurrence of transformations or other transitions, equally as well marked as those of the authors, has been pointed out by others. These observations have assisted us greatly. Consequently we were very pleased to see the authors' excellent work in finding these two transitions in chromium. With these confirming data, our picture of this element is clarified considerably, so we expect that at least some of our work can be published in the near future. R. C. Ruder (E. I. du Pont de Nemours & Cu., Wilmington, Del.)—The authors' interpretation of these transitions in terms of 3d to 4s electronic structure transitions is most interesting. It would be interesting to have additional experimental evidence of such transitions from the temperature dependence of the Hall coefficient in the neighborhood of the property changes discussed in this paper. Simple theory15 suggests the Hall coefficient as a measure of the free electron (or s electron) concentration per unit volume. It has been shown that for paramagnetic'" and ferromagnetic1? metals the simple theory is in fact too simple. However, the existence of a discontinuity in the Hall coefficient would provide information which should aid both in our understanding of these transitions and the significance of the Hall coefficient in these metals. It was rather surprising that no significant paramagnetic effects were observed. In this connection the recent work of McGuire and Kriessman18 is cited. They measured the magnetic susceptibility of chromium from 20" to 1460 °C. They also observed no large change in the susceptibility although there might be a change in slope in the vicinity of the 40 °C transition. The existence of these 3d to 4s electronic transitions has been discussed in connection with the paramagnetic susceptibility behavior of nickel and nickel alloys.'"-" Assuming a correspondence principle between classical and quantum mechanical paramagnetic theory and using classical theory to calculate the effective Bohr magneton number from the Curie constant for substances obeying the Curie-Weiss law," it is found that the effective magneton number is a function of temperature. The process of calculation involves the inverse of the differential of the 1/x4 vs. temperature curve so that good and numerous data are necessary to obtain significant results. The data of Fallot23 show a discontinuous increase of about 12 pct in the effective magneton number between 850" and 900 oC, followed by a continuous increase up to the melting point. The data of Sucksmith and Pearce24 show a possible 8 pct increase. The older data of Terry25 and Weiss and Foex26 show a continuous increase. It is possible that small amounts of impurity atoms change these electronic transitions significantly. Fallot's23 data on a nickel alloy with 4.5 atomic pct Fe indicate that the discontinuity occurs around 1300 °C. Systematic investigation of the transition metals for transitions of this nature should provide information which would be very valuable for our understanding of these metals. The absence of antiferromagnetic structures in chromium has been shown by Shull27 using neutron diffraction techniques. M. E. Fine, E. S. Greiner, and W. C. Ellis (authors' reply)—The remarks by Drs. Samans and Ham are certainly very interesting, in particular those pertaining to the close agreement between the theoretically calculated values for transition temperatures in chromium and the experimental values reported by a number of investigators. This is a remarkable achievement and we shall look forward to a more detailed presentation of the method followed in their calculations. We do not believe that the transition in pure chromium near 40 °C remains temperature invariant with alloying, as was reported by Samans and Ham for a number of the substances that they studied. We have not done any work with alloys but base our belief on the results of earlier studies in which less pure chromium was included and considerably lower transition temperatures were observed. The transition tempera-

Jan 1, 1952

By N. F. Fiore, M. F. McGuire

THIS communication describes a series of experiments in which dislocation etch pitting was used to ascertain the depth of damage in crystals which were mechanically polished or which were cut with either a commercial metallographic cut-off wheel,* a com- All specimens were cut from single crystals of American Smelting and Refining Co. 99.999+ pct pure copper which were grown from the melt by the Bridge-man technique. The test specimens were disks, with faces being (111) planes and the disk axis a (111) direction. The disks were annealed in a vacuum of 10-5 Torr for 24 hr at 950°C prior to cutting or polishing and were given a light electropolishing in an ortho-phosphoric acid bath before etch pitting. Both Youngs1 and Livingston's2 reagents were used for etch pitting and the reagents gave identical quantitative results; however Livingston's reagent produced less staining and so all photomicrographs shown are of {111) surfaces etched with this solution. The surface of the annealed crystals showed well-defined subboundaries and a density of dislocations of about 1 X 106 per sq cm excluding those present in subboundaries, Fig. 1. The depth of cold work produced during mechanical polishing was determined after an annealed specimen was mounted in a paraffin holding block to protect it from extraneous damage. The exposed (111) surface was ground on metallographic papers and then polished on billiard cloth through 0.05-p alumina abrasive. It was necessary to remove about 0.3 mm (-0.01 in.) to obtain a structure representative of the annealed sur- face, indicating that the crystal was damaged to this depth during mechanical polishing. The cold work caused by standard cutting methods was measured in another series of tests in which cuts

Jan 1, 1967

By H. C. Heard

The review by Professor J. C. Jaeger (Chapter 1) briefly summarizes and discusses a select group of papers by various workers dealing primarily with aspects of fracture in brittle rock materials. Professor Jaeger's treatment is primarily concerned with the correlation of phenomenological and theoretical failure criteria with empirical results from short duration tests at ambient temperatures and generally at low lithostatic and interstitial fluid pressures. As engineering rock mechanics becomes more concerned with new techniques of mineral exploration and production at increasingly greater depths in the crust, it is well to be aware of the effect of the environment -that of the superposed stress field upon the lithostatic and interstitial fluid pressure, the temperature and the duration of the loading upon the failure of rocks either by fracture or flow. All results to be discussed here are from laboratory tests on small homogeneous samples, thus caution should be used in the direct extrapolation of these results to large inhomogeneous rock masses having quite different boundary conditions in the earth. The purpose of this supplement is to briefly point out the major effects of these parameters as examined singly, with all others held constant, and to cite some recent results which apply to the main theme on the brittle failure of rocks. The total stress field imposed upon a small volume of porous and permeable rock in the earth's crust may be thought of as the sum of an applied differential stress, plus a lithostatic pressure, plus an interstitial fluid pressure. The differential stress portion may be completely specified by nine components, six shear and three normal. If the small volume element is in rotational equilibrium, by suitably choosing our coordinate axes we may resolve these nine components into the three principal com-

Jan 1, 1967

By E. A. G. Colls

IN all branches of the chemical industry, corrosion plays a very costly part unless it is suitably com-batted, and as a result it is probably correct that chemical and design engineers are more corrosion conscious in the field of chemical industry than in others. Most metals occur in nature in combination with other elements. The refined or reduced state to which man converts them for his use, by removing the combining elements, leaves them in an unstable condition. Therefore in most of the media to which the metals are exposed they are constantly combining with the constituents of their environment, or in other words they are continually being corroded. Similarly, nonmetallic materials are corroded by undergoing chemical change. The rate at which corrosion takes place varies widely from metal to metal and medium to medium. In practically all cases the corrosion of metals in solutions (electrolytes) is electrolytic in nature and the rate of corrosion is dependent on many factors such as temperature, pressure, internal stresses, galvanic action, metal-ion concentration, and so on. In the chemical industry substances must be handled which are particularly corrosive to materials of construction. At the chemical plants of The Consolidated Mining and Smelting Co. of Canada, Ltd. (otherwise known as Cominco), situated at Trail, B. C., Canada, the following are some of the materials that have to be handled: Gases. Sulphur dioxide, sulphur trioxide, carbon dioxide, carbon monoxide, oxygen, hydrogen fluoride, ammonia, hydrogen sulphide, and oxides of nitrogen. Liquids. Solutions of ammonium sulphate, ammonium sulphite, ammonium nitrate, caustic soda and potash, sulphuric acid, nitric acid, hydrofluo-silicic acid, hydrofluoric acid, phosphoric acid, aqua ammonia, and formic acid. Solids. Gypsum (containing phosphoric acid), ammonium sulphate, ammonium nitrate, phosphate rock, caustic soda, potash, and phosphate fertilizers.

Jan 1, 1951