Search Documents

By R. M. Foley, Hidesaburo Kurushima

About 25 pct of all Japanese pyrite comes from the Yanahara mine on Honchu Island. For the past 40 years lack of an economical recovery process forced the operator, Dowa Mining Co., to sell the pyrite for its contained sulfur only, leaving 7 million tons of high grade iron ore waste. Introduction of the Dorrco FluoSolids roasting system enabled the company to make use of its iron sulfides and also to find a market for the mine's considerable pyrrhotite production. The success of this project is of great importance to Japan's economy since it points the way toward material increase in her natural resources. Prior to use of the present process, no practical method was available for commercial exploitation of known large tonnages of pyrrhotite, while the copper content of the even larger deposits of pyrite made the roasted residue unacceptable for the iron and steel industry. In Europe, large amounts of copper-bearing pyrite cinder are given a chloridizing roast for separation of the copper and iron but this treatment is not economical in Japan where salt is imported from as far away as Egypt.

Jan 10, 1958

By E. H. Mohr

At the McGill concentrator of the Nevada Consolidated Copper Co., all flotation operations have been carried out in Forrester cells since November, 1926. In respect to cost of operation, the new cell has proved to be superior to the Callow, which it supplanted, and its incorporation in the flow sheet has resulted in a marked improvement in the metallurgy. Before citing the advantages of the new machine over the old, it should be explained that the Forrester has not only replaced the Callow, but it has made possible the elimination of a number of tables as well. When Callow cells were in use, table concentration preceded flotation. The ball mill pulp was elevated, by means of air lifts, to roughing Wilfley tables situated two floors directly above the flotation floor. On an intermediate floor were additional tables which cleaned the concentrate from those above. The finished table concentrate constituted approximately 60 per cent. of the total mill production, and contained about 40 per cent, of the recovered copper. The table tailings were returned to the classifiers, the overflow from which went to the flotation cells and the oversize to the ball mills. As soon as the Forrester cells were installed, this tabling operation was discontinued. The ball mill pulp now discharges into the classifiers direct, without the intermediate tabling. It was impracticable to ernploy the present flow sheet when Callow cells were in use, for the reason that unless the great,er part of the heavy mineral was first removed, it accumulated on the mats and adversely affected the flotation operation. By tabling ahead of flotation, it was practicable to maintain the concentrator at 10 to 20 per cent. greater capacity (depending up on the pyrite contnt of the ore) than was possible by flotation alone. This was due to the necessity for finer grinding in the latter case. Even though the table conecntrates contained only 6 to 8 per cent'. copper content, the low smelting costs made it advantageous to operate at high mill capacity, at the cost of low grade of product. Standard Section equipment With the old flow sheet, a standard section consisted of four ball mills and classifiers, one air. lift, 20 roughing tables, 10 cleaner tables, 12 primary

Jan 1, 1928

By P. W. Ramsey, E. J. Boyle, E. A. Anderson

ONLY a few zinc-rich alloys are in commercial use today, and these depend largely upon solid solution effects for their desirable properties. Typical examples are rolled alloys containing about I per cent of copper, with or without additions of elements such as magnesium,1 and die-casting alloys containing about 4 per cent of aluminum with small amounts of magnesium and sometimes copper.2 A number of elements are capable of forming alloys with zinc, which do not enter into solid solution except in limited degree. The present paper considers one such system, zinc-titanium, in which alloys having potentially useful properties in the rolled form were found. ZINC-TITANIUM SYSTEM The zinc-rich portion of the zinc-titanium diagram, as determined by standard methods in this laboratory,3 is shown in Fig. I. The portion of the diagram of significance in the present work extends from 0 to about 0.5 per cent titanium. Gebhardt4 places the eutectic at 0.45 per cent, but the evidence in favor of the composition given in Fig. I is considerable. The solid solubility of titanium in zinc is very low indeed and possibly places these alloys in a somewhat different category from the commercial alloys previously mentioned. ALLOY PREPARATION All of the alloys used in this work were prepared with titanium metal of 98.9 per cent purity. In most cases high-purity zinc (99.99 per cent) was used but sufficient work was done later to show that zinc of about high-grade composition would yield approximately equal results. Best practice in alloy manufacture seemed to be to prepare a zinc-titanium hardener by adding about 4 per cent of titanium metal to molten zinc and holding under a boric acid cover, with frequent stirrings, at 750°C. until the titanium had dissolved. The desired titanium content could readily be obtained in the final alloy by adding the calculated amount of this hardener. The alloys proved to be quite stable in composition, unless overheated, and, with reasonable temperature control, required no cover or flux to prevent loss of titanium content by oxidation. HOT-ROLLING TESTS Three alloys containing, by analysis, 0.05, 0.12, and 0.23 per cent titanium were selected for preliminary study. Slab cross sections revealed a marked grain refinement* (Fig. 2) in the two alloys of highest titanium content. Cast unalloyed zinc has a columnar grain structure similar to that shown for the alloy of lowest titanium content but without the scatter of small equiaxed grains at the center.

Jan 1, 1944

By Mark R. Lamb

THE treatment of slime is of special interest to those engaged in cyaniding gold- and silver-ores. The usual practice is to make as small a percentage of slime as possible. In many instances the slime is given no treatment, but is impounded in dams in the hope that the future will develop some method of economically treating this product. The filter-press was the first step upward from ordinary decantation, but, on account of heavy labor-charge and high cost, its use has been limited to high-grade material. The slime at the Combination mill at Goldfield averages perhaps $20 per ton, and although the values are quickly dissolved the filter-press installation was not entirely satisfactory, resulting in the erection of the canvas-cell filter, developed by Chas. Butters and his staff. This filter is a great improvement over the filter-press, and the following description of it will be of interest to those engaged in treating slime produced in crushing ores, especially in view of the fact that, by the use of this filter, slime can be treated at a lesser cost and with a higher percentage of gold- or silver-extraction than in the ordinary treatment of sand; and, moreover, the initial outlay for an all-sliming plant is less than that for the ordinary sand- and slime-plant. The economy of construction of the Butters filter-plant is clearly shown in Figs. 1 and 2, which illustrate the 20-frame filter of 40 tons capacity, now being installed by the Nevada Goldfield Reduction Co. In this construction the slime-pump is so connected that it can pump to or from either tank or the filter by changing the valve-settings-a combination which is necessary in this particular installation, since sufficient fall is not available for filling and discharging the filter by gravity. Ordinarily, a slime-plant comprises: a filter-box with frames

Jan 1, 1907

By John Lohrenz

Consider an investor who, knowing future costs and revenues, can choose how rapidly to produce from a given mineral source. If the investor elects to make that choice to maximize present value of future profits, how do policies affect the choice? Various alternative policies are examined. Some, such as higher royalty rates, lead to slower production rates than would otherwise obtain. Clearly, the chosen rates of production are policy-dependent. One is wisely counseled to consider how mineral policies affect the rate of production from given sources when analyzing current and alternative policies.

Jan 1, 1982

By L. S. Darken

IN the study of reactions occurring in liquid iron, alone or in contact with a liquid oxide or slag phase, it has been found that the experimental data over a limited range of concentration can in some cases be repre-sented satisfactorily by the simple equilibrium expression K - (p1)p1 (p2)p2 . (R1)r1(R2)r2 . where (P) denotes the concentration of a product and (R) the concentra-tion of a reactant in the reaction r1R1 + r2R2 + . . . Some of the reactions for which it holds are listed in Table 1. For others, however, the simple equation apparently does not hold. This has been attributed to an improper method of expressing concentration (for instance, weight per cent instead of mol fraction); or it has been supposed that the solutions are not ideal in the sense that the activity of a com-ponent is not proportional to its true mol fraction, But it may be that the problem has been oversimplified by neglecting some molecular species actually present; that is, by considering only the ostensible simple com-ponents and thus leaving out of account possible compound formation. It is the purpose of the present paper to point out how, in a group of related cases, a reasonable consistent assumption relative to the presence of a compound makes it possible to express the experimental data satis-factorily by the simple equilibrium expression when this compound is taken into account, and to bring into harmony data referring to different reactions in liquid iron. There are several a priori reasons for believing that solutions in liquid iron should not deviate far from ideality, provided that the concentration of solute is not too great and is expressed in proper terms. The factors that commonly lead to nonideality in systems at ordinary temperature as ionization or the occurrence of polar and nonpolar molecules-are presumably less effective in metal and in slag systems at high temperature. Again, the type of equation commonly used to express the value of

Jan 1, 1940

By John S. Crandall

Occurrence: small crystals in alluvial sands from the eroding Belt Series mica schists. Flowsheet: dragline, trommel screen, jigs, drier, crusher, screens. Value: ground, $2.50 per cu yd, garnet sand gross $60. per ton. Costs: production and sales $48. per ton. Uses: blasting sand in aircraft plants, monumental works, foundries. Efficiency comparison: superior to silica sand. Future: possibilities only touched upon, research continuing.

Jan 1, 1950

By Michael S. Roscoe

In order to more accurately predict longwall surface subsidence over the Pittsburgh No. 8 Coal in Eastern Ohio, North American Coal Corporation's Quarto Mining Company undertook or participated in several subsidence studies. Due to the changing roof geology and rapid variations in the amount of cover two separate areas were investigated at two different mines to determine the subsidence response if any to these changes. Data generated from these studies were compared with NCB derived,data for accuracy and then used to predict subsidence under houses, gas lines and other critical man made structures. The following report summarizes the results of these studies as well as the subsidence case histories of gas lines, transmission towers, houses and water wells. Problems that were encountered during both phases of this process (investigation and subsequent application) are also included.

By Carl J. McHargue

Rods of 99.99 + pct Al which had initial orientatzons of <001>, <118>, <115>, <111>, and random were swaged at room temperature. Changes in orientation as a function of deformation were studied on axis distribution charts. The <001> orientation appeared to be relatively stable due to the inhomogeneity of the deformation process. near the <100> zone were quickly reoriented towards <001>. Orientations on the <110> zone between <118> and <115> appeared to be stable to reductions of about 50 pct, then were reoriented toward <001>. At very high reductzotzs. movement away from the <111> orientation was observed. the requirement that a circular cross section be maintained. In addition to these mechanical factors, there are grain-boundary effects in poly crystalline materials which are not yet understood. Hartmann and Macherauch conclude, for example, that multiple slip occurs for all orientations in fine-grained aluminum and copper and that the choice of operative slip systems has no simple relationship to orientation.? Many investigators have attempted to avoid problems of interpretation caused by an initial texture by treating the starting material to obtain as ran- IT has been generally accepted that the deformation texture obtained at high reductions, e.g. 90 pct, will not be noticeably affected by a prior texture; whereas, that obtained at reductions of 40 to 50 pct may be significantly influenced by the specimen history.&apos; Some recent studies, however, have been interpreted as showing that an initial texture strongly influenced the deformation textures in rods at reductions greater than 90 pct. Freda and Cullity suggested that the <001> texture in a heavily cold-worked copper rod was due to a <001> texture in the original casting. McHargue, Jetter? and Ogle concluded that the <001> component in an aluminum rod extruded at liquid nitrogen temperature was remanent from a <001> texture in the cast extrusion billet.3 Most of the published work on the effect of initial orientation on deformation textures has been for cold-rolled or compressed single crystals,4-6 The primary interest in these studies was to examine various orientations with regard to their stability under flow? thus determining the possibility of such orientations being stable end orientations. There appears to be no published studies on the effect of initial orientation on fiber textures in polycrystalline specimens. A recent study, however, is concerned with the reorientation of individual grains in polycrystalline specimens pulled in tension.? Although the reorientation of single crystals loaded in simple tension is well known, the movements in the forming of wires and rods would be expected to be different due to the circular array of radial-compressive stresses exerted by the die walls or the rolls, and to

Jan 1, 1962

By Laurence Delisle, Aaron Finger

THE alloys formed by the addition of nickel to iron by convelltional metallurgical procedures show physical properties that differ widely from those of the individual metals. The effect of alloying on the mechanical properties is most pronounced in alloys containing between 15 and 25 per cent nickel. The tensile strength of an alloy containing, for example, 20 per cent nickel and 80 per cent iron (with 0.06 per cent carbon), in an annealed condition, is above 150,000 lb. per sq. in.? owing to a martensitic type of transformation, as compared with about 50,000 lb. per sq. in. for pure iron in the same condition. The object of this work was to determine whether the same beneficial alloying effect could be obtained in alloys of iron and nickel prepared by powder metallurgy technique. PROCEDURE Bars and pellets for tension and compression tests, respectively, were made. Two groups of specimens were prepared: (I) by cold-pressing the powders and sintering; (2) by cold-pressing the powders, sintering, repressing and resintering. Raw Materials Nickel powder supplied by Metals Disintegrating co., marked MD-151, was used. A typical analysis of this powder was as follows: sulphur, 0.040 per cent; copper, 0.18; iron, 0.23; manganese, 0.002; magnesium, 0.001 5 ; lead, 0.035; tin, 0.025 ; silicon, 0.08; chromium, 0.008. Electrolytic iron powder supplied by Plastic Metals Inc. was used. A representative chemical analysis for impurities other than gases, supplied by the vendor, gave the following results: carbon, 0.005 per cent; manganese, 0.002; silicon, 0.003; phosphorus, 0.001; sulphur, 0.004; nickel, 0.008. The fractions from these powders passing a 3 2 5-mesh sieve were reduced in hydrogen at 600°C. for one hour, to clean the surfaces of the particles. The reduced powders, slightly caked, were ground in a mortar and screened again through a 325- mesh sieve. Mixing The proper proportions of the powders were mixed overnight on rolls, in glass jars fitted with iron-wire baffles to break aggregates of particles that might form. Pressing All specimens were compacted on hydraulic presses. The pellets were compacted in a cylindrical die, ½ in. diameter. The ratio of thickness to the diameter of the pellets was maintained as nearly as possible at 0.9, as specifed for standard short compression pieces. The tensile bars were made by compacting 30 grams of powder. Their shape is shown in Fig. I. The compacting pressures for the pellets and the tensile bars were:

Jan 1, 1946

By Allan T. Gwathmey, J. Bruce Wagner, Kenneth R. Lawless

Between 250°and 550°C in oxygen pressures of 10 to 760 mm Hg, the relative oxide thicknesses formed per unit time on the (100), (111), (110), and (320), decreased in this order. The predominant oxide orientation was (001)Fe3O4 and [110] Fe304 A small amount of a-Fe2O3 which exhibited a fiber pattern was observed in all oxides except those formed at 250°c in low oxygen pressures. IN order to understand the properties and behavior of thin films, particularly their role in oxidation reactions, there is needed more experimental information on their structure, composition, and kinetics of formation on clean surfaces of known geometry. The present study was undertaken to obtain such information for thin oxide films formed on single crystals of a body centered cubic metal, iron. Crystals in the form of spheres were used in order to expose all possible crystal planes to the reactant gases simultaneously. Using this procedure the relative rates of oxidation of all planes could be estimated, and those exhibiting, maximum or minimum oxidation rates could be selected for a more intensive study of composition and expitaxy. Since the three types of information were obtained from the same experiment using a single crystal substrate, any differences between rate, composition, and expitaxy on the several planes may be attributed to the influence of the substrate structure. EXPERIMENTAL The starting material for this study was Armco iron rods, 6 in. long and 3/8 or 1/2 in. in diam. The analysis was reported to be 99.8 pct Fe, with major impurities listed as carbon 0.018 pct, manganese 0.027 pct, phosphorous 0.005 pct, sulfur 0.029 pct, silicon 0.005 pct, and copper 0.11 pct. These rods were cleaned with ether and heated in an atmosphere of moist hydrogen at 950°C for three days. The purpose of this treatment was to decarburize the iron and to provide a consistent, uniform grain size for the growth of single crystals. Crystals in the form of rods, up to 1/2 in. in diam and 2 in. long, were prepared by a method similar to that reported by Leidheiser and Buck.2 Spherical crystals, 3/8 and 1/2 in. in diam and having a handle about 1/4 in. in diam by 112 in. long, were machined from the single-crystal rods. After machining, each crystal was etched in aqueous nitric acid to remove the cold-worked metal at the surface. Before each experiment, the crystal was polished mechanically with metallographic papers through number 4/0, and electropolished in a perchloric acid-acetic anhydride mixture by the method of Jacquet and Rocquet.3 The crystal was washed in running distilled water for at least 5 min. The excess water was blotted with a soft paper tissue, and the crystal was placed in an all-glass reaction vessel (See Fig. 1). The crystal was heated at 550°C in hydrogen for at least 8 hr prior to the oxidation in order to reduce any surface oxides and to help relieve any stresses in the metal. For the structure and composition studies, flat faces were cut parallel to (loo), (111), and (110) planes on the iron crystal spheres. The orientation of these faces was checked by a back-reflection X-ray diffraction technique. The faces were within 2 deg of the desired orientation. The flat faces were treated as described above except that prior to electropolishing they were given an additional polish on metallographic felt saturated with twenty-minute levigated alumina. After the crystal was heated in hydrogen for at least 8 hr, the temperature was adjusted to the desired value, and the hydrogen was evacuated. Commercial oxygen which had been purified by successively passing through tubes containing magnesium perchlorate, Ascarite and magnesium perchlorate was admitted to the desired pressure as measured by a mercury manometer. A resistance-wound furnace surrounded the oxidation chamber, and a temperature controller maintained the temperature within ±3°C. The furnace was provided with a small window for observing the crystal. The changes in thickness of the oxide films were followed by observing the interference colors. The oxidation was allowed to proceed until the desired oxide thickness was attained on a given crystal plane. The experiment was terminated by evacuating the oxidation

Jan 1, 1962

By W. A. Vine

When a hole is made in a stressed solid, such as rock pierced by mine openings, equilibrium of the solid is destroyed. To restablish that equilibrium the stress condition in the rock surrounding the opening becomes rearranged. This rearrangement may or may not develop local stresses in the vicinity of the opening which exceed the elastic strength of the rock. Since stability of the opening depends, therefore, on the strength of the naturally occurring rock surrounding the opening, this rock is an engineering material of construction, and all rock affected by the associated opening or system of openings may be considered a structure. The term invert is chosen to describe the formation of the structure built from the inside, as it were, and a consequence of mining rather than an entity built for a purpose. By definition, an invert structure is formed when openings are made underground and is com- posed of that material on the solid side of a rock-air interface wherein the stress condition is affected by the associated opening or system of openings. The shape of an invert structure is never clearly defined; the skin of the structure may be mapped, and even described, but the boundary of the structure within the solid rock mass must be arbitrarily set.

Nov 1, 1955

By Samuel Taylor

IF I LIVE another fourteen months and am still con-nected with the coal industry, I shall then have com-pleted a half century with it. Since May, 1874, when .I first entered the bituminous workings as a miner, I think I have held almost every position connected with a mine except possibly that of mule driver, for which I was unfitted by reason of my religious upbringing. We are all agreed, at least I have not heard it contra-dicted, that there is serious over-production in the bituminous industry. This has come about in various ways and is easily explained. During the Fuel Admin-istration, I recall making an estimate of the possible output of the bituminous mines of the country provided they were given a full force of men and a full-car supply; my estimate was a little over a billion tons a year. A few months ago, the late Francis H. Peabody, of Chicago, made a practically identical estimate. If, however, both of these conditions should happen con-currently, there would very soon be no market for the coal, and many of the mines would close down. Even today, if 10 per cent. more cars were furnished, to the bituminous mines, market prices would drop very seriously.

Jan 4, 1923

By C. H. Mathewson

EXCEPTING the joint sessions on gases in metals held during the day on Tuesday, the Institute of .Metals opened its activities with a division dinner at the Commodore on Tuesday evening, with Sam Tour, retiring chairman, presiding. W. M. Corse, secretary-treasurer, outlined the financial status of the division and stated the investment fund is becoming large enough so that in the near future it will be possible to pay all expenses of a foreign lecturer once in two years and not rely on an extended speaking tour to cover expenses. W. B. Price reported on his attendance at the Zurich, Switzerland, meeting of the International Society of Testing Materials and gave a graphic account of his visit to the Grand Salon, his meeting with Mussolini, and his audience with the Pope. Buffalo was announced as the place of the fall meeting, to be held during the week of Oct. 3.

Jan 1, 1932

I;. D. Godshall, Everett, Wash. (communication to the Secretary) : In Mr. Morse&apos;s interesting paper several statements occur which seem to require correction and comment. This is the more appropriate, since Mr. Morse has mentioned me by name, and has cited my "Review of the Russell Process,"* so that silence on my part might be taken as indicating an assent which I cannot give. On the first page of his paper Mr. Morse says that the " goingback " of chlorination was " the only difficulty encountered at Aspen," and adds that he has " never seen any explanation " of the cause. The plain inference is that he now fills this complete

Jan 1, 1896

By Michael B. Bever, Barton Roessler

The effects of deformation by wire drawing at 78OK on initially ordered and initially disordered specimens of the alloy Cu3Au were investigated. The resistivity, stored energy, drawing force, and microhardness were measured as functions of strain; microstructural changes were observed. The results are interpreted in terms of the structural imperfections and the changes in atomic configuration resulting from deformation. A few experiments on the effects of room-temperature annealing after deformation at 78°K were made; they suggest vacancy-promoted ordering in disordered alloys. BARTON ROESSLER, Junior Member AIME, formerly Graduate Student and Alcoa Fellow, Department of Metallurgy, Massachusetts Institute of Technology, Cambridge, Mass., is with Westinghouse Research Laboratories, Pittsburgh, Penn. MICHAEL B. BEVER, Member AIME, is Professor of Metallurgy, Massachusetts Institute of Technology. Based in part on o thesis by B. ROESSLER submitted in October, 1959 to the Massachusetts Institute of Technology in partial fulfillment of the requirements for the degree of Doctor of Science. Manuscript submitted April 6, 1961. IMD AN investigation of the effects of deformation at room temperature on the alloy Cu3 Au was reported in a recent paper,&apos; which included a review of the literature on the deformation of order-disorder alloys. In general, plastic deformation of ordered alloys reduces the degree of long-range order and causes corresponding changes in their properties. Deformation of disordered alloys changes their properties in a manner characteristic of solid solution alloys; these changes can in part be attributed to the destruction of short-range order. The effects of deformation on solid solution alloys are of two kinds: 1) generation of structural imperfections, which occurs as a result of deformation in any metallic system including pure metals, and 2) changes of atomic configuration, which are characteristic of solid solutions and particularly of order -disorder systems. These two types of effect are not independent of each other and the state of a deformed solid solution alloy is determined in a complex manner by the way in which the structural imperfections cause changes in atomic configuration both during and after deformation.

Jan 1, 1962

INTRODUCTION Porphyry copper deposits have been reported from the Caribbean area by Pease (1966), Cox, et al. (1973), Guild (1974), Kesler, et al. (1975), and others. This chapter summarizes the most widely known characteristics of those deposits. Only one deposit that conceivably can be classed as a porphyry copper occurrence is in production (Pueblo Viejo, Dominican Republic), but others are known whose tonnage and grade are of economic interest. Deposits in this province may be classified as copper-gold or copper-molybdenum types (Kesler, 1972), but deposits associated with quartz-rich plutons that have high Na2O:K2O and high gold:copper but low molybdenum: copper ratios dominate. Porphyry copper occurrences are reported in the literature from Puerto Rico, Haiti, the Dominican Republic, Jamaica, and Cuba. Only the porphyry copper deposits from Puerto Rico are extensively described in the literature; consequently the Caribbean porphyry copper province in general is not as well documented as the southern Cordilleran orogen. Because past published technical descriptions are incomplete, some data presented here are new to the literature. The Caribbean includes the island arcs between North and South America. Porphyry copper occurrences are known from the Greater Antilles, the generally east-west trending group of islands that lies south of North America. Fig. 48, therefore, only covers the Greater Antilles portion of the Caribbean. Porphyry copper deposits in this area are not described by the Lowell and Guilbert (1970) model in details of metallization (general paucity of molybdenum), alteration (scarcity of orthoclase), or petrography (preponderance of quartz diorite). Therefore, this model should be modified to include deposits associated with quartz-bearing plutons such as those found in the Caribbean. In the Meme deposit on Haiti ore occurs in skarn adjacent to the quartz diorite phase of a composite quartz monzonite-granodio-rite-quartz diorite pluton (Kesler, 1968). This deposit, with a K-Ar 66 m.y. date, is not included in Fig. 48 as a porphyry copper deposit because metallization is restricted largely to the intruded rocks. Although the intrusive rocks at the Meme deposit may contain sulfide near skarn contacts they are otherwise essentially unaltered. Porphyry molybdenum deposits as defined by Clarke (1972) have not been reported in the Caribbean area.

Jan 1, 1978

By M. B. Bever, A. K. Jena

THE heats of formation ?H at 273°K of the compound AgMg as a function of composition have been measured by solution calorimetry.1 The value at the stoichiometric composition is -4.41 kcal per g-atom. From electromotive force measurements2&apos;3 the heat of formation at 773°K of stoichiometric AgMg has been determined as -5.19 kcal per g-atom.4 The combination of these two values results in an unusually high negative temperature coefficient of the heat of formation d?H/dT = ?Cp = -1.6 cal per g-atom-OK. By contrast, published heat contents of the compound AgMg and the component elements above room temperature5 indicate that the temperature coefficient of the heat of formation of AgMg is nearly zero. In this communication calorimetrically measured heats of formation of A.K.JENA,Junior- MemberAIME,andM.B. BEVER,Member AIME, are Staff Member, Division of Sponsored Research, and Professor of Metallurgy, respectively, Massachusetts Institute of Technology, Cambridge, Mass. Manuscript submitted July 1, 1968. IMD AgMg below room temperature are reported and the temperature dependence of the heat of formation is discussed. The heat effects of additions of samples of the compound AgMg containing 50.1 at. pct Mg to liquid tin-rich solutions at 623°K were measured in a solution Calorimeter.6 The heat effects of additions plotted against the average of the atom fractions of solutes in the solution before and after each addition were a linear function of composition from which the heat effect at infinite dilution was obtained, Table I. The calorimeter was calibrated by additions of tin; the heat content (H623°K - H273°K) of tin was taken as 4.08 kcal per g-atom.4 The heat effect at infinite dilution of an addition of where heat of formation of AgMg at T°K, T = temperature from which samples are added (78°, 195°. and 273°K), Xi = atom fraction of i in AgMg, ?Hi = relative partial gram-atomic enthalpy of i in tin-rich solution.

Jan 1, 1969

By M. E. Wadsworth, T. L. MacKay

Sintered UO, samples were leached in sulfuric acid solutions of various concentrations. A pressurized system was used so that it was possible to investigate the kinetics of the reaction to 270°C with oxygen overpressures as high as 900 psi. The rate was observed to be a function of the concentration of hydrogen ions and directly proportional to the partial pressure of oxygen. Evidences are presented which indicate that a UO2 surface site reacts with a molecule of water to form a hydroxyl complex which in turn can dissociate with the characteristics of a weak acid. A rate determining step has been proposed which involves the reaction between an oxygen molecule and the hydroxyl complex on the surface of UO,. ThE 2 principal methods for uranium dissolution are carbonate and acid leaching. The sulfuric acid leach is the more popular and is used for the treatment of the majority of the ores of Africa, Canada, and the United States. Low recoveries in basic leach circuits led investigators at the University of British columbia1 to study leaching of uranium ores in pressurized vessels. Early in the study of dissolution of uranium it was found that only uranium in the hexava-lent state could be leached in acid or basic circuits. Therefore, the use of oxygen over-pressure in an autoclave offered an interesting approach to solving the low recovery problems of carbonate leaching. UO, was used in this study because it could be obtained in high purity and also because it is representative of the most refractory of the primary uranium minerals. A pressurized system was used to provide a means whereby important temperature and pressure parameters could be varied for the evaluation of the kinetic processes. The mechanism for the dissolution of UO2 should be similar for any of the uraninite type minerals. At the present all of the kinetic studies that have been conducted have been in carbonate media. Peters and Halpern2 carried out a kinetic study of the leaching of pitchblende. Their specimens were pitchblende ores selected on the basis of high grade and homogeneity. Pearson and wadsworth3 conducted a kinetic study of the dissolution of UO2 in carbonate solutions with results very similar to those obtained by Peters and Halpern. EXPERIMENTAL The UO2 as received* was found by spectroscopic *Mallinckrodt reagent, supplied by the Atomic Energy Commission. analysis to have a purity of 99.94 pct 0.03. It was ground in a mechanical agate mortar and screened through a 400-mesh sieve. Thin flat disks of UO2 were prepared by pressing the sized powder in a specially constructed die at a total pressure of approximately 25 tons per sq in. The pressed disks were approximately 0.25 cm thick, 1.6 cm diam, and 3.5 g in weight. As pressed, the samples were approximately 65 pct of theoretical density. It was essential that a binder such as poly-vinyl alcohol be added before pressing to prevent formation of cracks when fired. It was found by trial and error that pressed disks sintered close to 1870°C in a hydrogen atmosphere, reach densities between 91 and 91.5 pct of the theoretical density. At this density the samples had no measurable porosity based upon a 2-hr emersion in boiling water. An X-ray examination of these sintered UO2 disks showed them to be identical with the original UO2 received. Reaction of UO2 with the alundum furnace core was prevented by placing molybdenum between the samples and the core according to the method of Corwin and Eyerly.4 Leaching studies were carried out in a specially designed autoclave, the details of which have been presented e1sewhere.6 The main features of the equipment as applied to a kinetic study are: 1) solution samples may be removed during the course of a single run; and 2) temperature and agitation are carefully controlled. Two-ml samples removed from the autoclave during the course of a run were analyzed for U3O8 content with a Beckman model DK-2 spectrophotometer by the method of

Jan 1, 1959

By Joseph Newton

MUCH the same story can be told about the copper industry for the year 1944 as for the three preceding years. Operators report few or no technical changes at their plants and the main endeavor has been to maintain high production with existing equipment. No large new installations have been made to increase plant capacities and apparently over-all copper production has passed its maximum. The present decline in copper production results partly from the severe labor shortage. As is true of most industries; the outstanding fact about the copper industry during the past few years has been its tremendous and sustained production which has been maintained in spite of serious shortages in material. labor, and technical personnel. The figures in Table I give a concrete example of how production has been increased at one large smelter in the United States-the Garfield plant of the American Smelting and Refining Co. at Garfield. Utah. These figures, reported by W. G. Rouillard. superintendent. give the production of the Garfield plant for the five years 1940-44 inclusive. The total blister production

Jan 1, 1945