Search Documents

Jan 1, 1957

By J. A. Fellows, Earnshaw Cook, H. S. Avery

THE increased use of heat-resistant alloys (26 per cent Cr, 12 per cent Ni; 16 per cent Cr, 35 per cent Ni; 12 per cent Cr, 60 per cent Ni; etc.) in recent years has been accompanied by continued demands by the consumer for improvement in properties. The manufacturers of these materials, of necessity, have resorted to more critical studies of the basic causes of variations in fundamental properties. To keep pace with the need for augmented information, previous techniques of investigation have been refined and new test methods and instruments created. It is the purpose of this paper to describe the apparatus, experimental technique and precision of measurement that were employed in the exploration of properties of heat-resistant alloy presented in a companion paper.? The detailed precautions in experimental procedure essential for attainment of accurate and comparable data at elevated temperatures cannot be too highly emphasized. THE CREEP TEST Since the fundamental concepts of creep testing have been recognized for the past 20 years, present interest is restricted to refinements in equipment and experimental procedure. The creep-test laboratory constructed for the American Brake Shoe and Foundry Co. is designed to permit 1000-hr. tests in the temperature range of 1200° to 2200°F. with a choice of applied stress extending from 50 to 50,000 lb. per sq. in. in increments of 50 lb. per sq. in. To simplify the calculation of weight combinations, the loading beams (Fig. I) are provided with counterweights to eliminate the tare. The precision of the knife-edges (10.1 ratio) is such that a 10-gram weight placed on the upper specimen grip will be exactly balanced by a 1-gram weight attached to the loading shackle. Check of the loading weights proved the maximum error to be 0.06 per cent. Axial alignment is provided by crossed knife-edges in the grip seats. The furnaces are similar in design to those of Crane and Company, Battelle Memorial Institute, and the U.S. Steel Corporation. An 80 per cent Pt, 20 per cent Rh No. 19 B. and S. gauge wire is used as the heating element. The details of construction are shown in the radiograph reproduced in Fig. 2. The windings are held in place on an alundum tube with alundum cement; the distribution of turns is adjusted to give a maximum temperature gradient of ± 1°F. over a 4-in. gauge length (Fig. 3). To avoid sharp temperature differentials at the ends of the test section, the length of the furnace is four times the gauge length. Sixteen-inch coupons are used to reduce the temperature of the threaded

Jan 1, 1942

By Robert Forsyth

As the latest plant on a large scale, the new Bessemer works of the North Chicago Rolling Mill Company, at South Chicago, presents some features of interest to steel-makers, I have ventured to lay before the Institute a short description of that plant, and some* remarks upon the practice there. At the time the South Chicago works were designed the adoption of the basic process in this country seemed imminent. Experience in Europe had demonstrated the perfect success of the process technically, and the question of its commercial value was one which, for any particular works, would have to be settled by its special advantages for procuring the necessary ores and basic materials. Under the circumstances, it was thought best at South Chicago to so arrange the plant as to allow the introdnction of the basic whenever it became advisable, and to make such other changes from the standard type of Bessemer plant as the state of the art seemed to demand and to foreshadow. As the use of metal direct from the blast furnace, while generally condemned by experts here, was in such successful practice in Europe (particularly in connection with the basic process), there was no doubt about its feasibility, while its economy in fuel and labor made it especially attractive to the Western manufacturer. It was accordingly decided to build a direct-metal plant adapted to the basic process. The ingots made were to be rolled into rails at one heat, and were to be of such size (12 inches square and long enough for three and four rails) as to be readily and quickly handled by the rolling machinery proposed. This small size of ingots, and the large number cast from each heat of 10 tons, made it necessary to provide a good deal of room in the casting-pit—much more than in any previons plant—and to put down extra facilities for handling ingots. To meet the delays incident to the basic process—to insure that one vessel should be always blowing if necessary, and to provide opportunity for current repairs to linings, etc.—it was decided that three vessels should be used, and, to properly concentrate the work of

Jan 1, 1884

By J. O. Glanville, L. H. Haley

Ice frozen from a dilute chemical solution is mechanically weaker than ice frozen from pure water. This phenomenon is the basis of a practical method for reducing the strength of a mass of frozen coal. If a chemical additive is applied to moist coal prior to its shipment during freezing weather, the resulting frozen coal can be more easily broken than in the absence of the chemical additive. This greatly expedites the unloading and handling of coal during winter. There has been considerable research into the nature and mechanical strength of ice frozen from various solutions. In this paper, literature relating to this process as well as literature relating to the chemical treatment of coal and mineral particulates is reviewed. Some important articles are discussed and speculations made about the nature of the ice-weakening process. A laboratory evaluation of the effects of chemical additives on the mechanical strength of ice and frozen coal has been made. An apparatus designed for this purpose is described, and some results obtained with it are discussed.

Jan 1, 1983

By C. S. Samis, J. C. Mitchell

Sodion activity data have been obtained for the Na-A1 system for sodium concentrations in aluminum between NN, = 25 . 10-and 300 x 10'. This concentration intert-a2 encompasses those sodium concentrations nor1)zally encountered in aluminum reduction cell operation. The sodium activity data were measured by a two-phase equilibration of sodium between a lead and an aluminam rich phase. The Na-Pb system was emplojed as a reference for the determination of the actiz7itj 0.f sodium. The activity of sodiin in aluminuwz exhibits large positi2.e deviations frorn ideality and a strong dependence, on concentration below NN, = 100 x 1K6. The inteated data indicate that the activity of aluminium is equal to its mole fraction over the range of miscibility of the Na-A1 sgstem. The data on the Na-A1 binary have been combined with experimental data on the cryolite-A1 system at 1025°C to obtain the activities of Na F and AlF, in liquid cryolite oz2er the cornposition 1-ange encountered in aluminum cell operation. The results are in agreement with activities calculated from the NaF-AlF, phase diagram. ALUMINUM is produced commercially by the electrolytic reduction of aluminum oxide dissolved in molten cryolite. There is considerable controversy over the actual mechanism of the discharge processes, but sodium potentials in the systems appear to play an important role in the reduction mechanism. The metal-salt reaction involving NaF and aluminum to produce A1F3 and sodium is responsible for the presence of sodium in the aluminum metal phase. Additional sodium may be produced from the simultaneous deposition of sodium and aluminum at the cathode as a result of a cathodic overvoltage. runert' has suggested that sodium gas at atmospheric pressure would be the result of reaction between cryolite and aluminum at 1000°C. Subsequent investigations have shown that production of sodium at atmospheric pressure does not occur. These later investigations can be conveniently separated into two categories. The first involves sodium, aluminum, and cryolite, in which the sodium activity was measured. The second includes a lead phase for sodium activity measurement. Jander and errmann,' studied the reaction: at 1090°C in alumina crucibles under an atmosphere of dry, oxygen-free nitrogen. The equilibrium constant for the reaction was expressed in terms of concentration. Their results in Fig. 1 show an increase in sodium content of the aluminum with increasing NaF/A1F3 weight ratio. Pearson and waddington3 performed similar experiments at 1000°C. Their results are included in Fig. 1. Dewing and ollinshead have measured the sodium content of aluminum as a function of the NF/AF, ratio at 1025"C, Fig. 1, and ewin' measured the sodium content of the aluminum in a system involving the solid reactants NaF, cryolite, and liquid aluminum. This reaction is different from those discussed above. Two solid phases, NaF and Na3A1F6, and a liquid aluminum phase were present. The sodium concentration in the aluminum was determined by the temperature. Dewing's measurements covered the temperature range 679" to 896°C. Omo, Matsushima, and 1t02" investigated the equilibrium 6NaF ential thermal analysis. Stokes and Frank6 determined sodium activities by

Jan 1, 1970

By Pei-Yung Huang, C. R. Hayward

In order to understand more fully the actual state of copper lost in copper reverberatory slags, a systematic study on the various reactions between certain metallurgically important copper compounds and synthetic copper reverberatory slags was undertaken by the authors in the Massachusetts Institute of Technology from 1942 to 1945.1 This paper, being only a part of the work completed, is published first because it furnishes the first experimental evidence of the formation of copper ferrite from reactions between cuprous oxide and copper reverberatory slags. Choice of Slag Composition The choice of the composition of the synthetic reverberatory slags to be used was much deliberated. Commercial copper reverberatory slags, neglecting minor constituents, avcrage :2,3 45 to 47 pct FeO; 38 to 42 pct SiO2; 5 to 6 pct CaO; 5 to 6 pct A12O3. Since the ternary system CaO-FeO-SiO2 has been much more thoroughly studied4 and is much simpler than the quaternary system CaO-FeO-SiO2-Al2O3, it was decided to use calcium oxide only instead of calcium oxide and alumina in the synthesis of the slags. Fortunately the composition of the average copper reverberatory slag with calcium oxide substituted for alumina lies in the region of the phase diagram clarified by the investigators. A survey of the phase diagram (Fig I) suggested two compositions: (I) the composition near the invariant point S, which is made up of 46 pct ferrous oxide, 37 pct silica and 17 pct calcium oxide; (2) the composition near the invariant point K with 45.5 pct ferrous oxide, 43 pct silica and 11.5 pct calcium oxide. Composition S has the advantage that the percentages of ferrous oxide and of silica almost exactly coincide with those of the average reverberatory slags, and that of the lowest melting point (1093º ± 3ºC) in the whole ternary system. The calcium oxide content, however, obviously is high. Since we have already substituted calcium oxide for alumina, and since calcium oxide is more basic than alumina, the fulfil- slag is decidedly too basic. Composition K has a slightly higher melting point (1150O + 3OC) and a higher silica content, but this is preferred because the slag is saturated with respect to tri-dymite and thus should not corrode siliceous refractories. Besides, it is less basic than composition S. The filial slag composition, therefore, was chosen to

Jan 1, 1949

By Thomas Watson

INTRODUCTION THE users of barite in the United States derive their supply partly from the domestic production and partly from the imports from foreign countries. According to the Mineral Resource division of the U. S. Geological Survey, the domestic production of barite in 1913 was 45,298 short tons, valued at $156,275, or $3.45 a ton, and the imports of crude barite were 35,840 short tons, valued at $61,409, or $1.71 a ton. These figures clearly show a decided advantage in cost of the foreign over the domestic barite to users in the United States. The difference in cost is the only advantage to the consumer of foreign barite, for there are large reserves of the mineral in the United States of good grade. The production of many of the operating mines is capable of decided increase, and it is believed that the operating mines together with the large reserves of undeveloped deposits of barite are entirely adequate to meet the demands of the users in the United States. Deposits of barite are known in California, Idaho, Nevada, and Alaska, but most of them are undeveloped because there is, apparently, no market for the .material in that region. The domestic production is derived from Missouri and the Appalachian States, the greater part being obtained from Missouri. Following the outbreak of war in Europe many users of foreign barite in the United States have been forced to seek their supplies at home. It seems opportune at this time, therefore, that a general review be given of the barite industry in the Appalachian States, one of the two areas from which the domestic supply of the mineral is derived, and that attention be directed to the undeveloped deposits in the region. Briefly, then, this paper reviews the barite industry in the Appalachian States, and describes the occurrence, preparation, and uses of the mineral.

Jan 2, 1915

By Sandip K. Mitra, John E. Dorn

The Basinki-modified Seeger equation for deformation of metals by means of thermally activated intersection of dislocations was used to ascertain the various factors responsible for the strain hardening of poly crystalline aluminum and a series of a solid solutions of magnesium in aluminum. The analyses were based principally on the rate of change of strain rate with stress and the Cottrell-Stokes ratio. From measurements of these quantities on a series of strain-hardened states, the force displacement diagram for intersection, the density of dislocations in the entanglements, and the contributions of the athermal local stress and long-range stress interactions were deduced. Poly crystalline aluminum was observed to have the same force-displacement diagram for intersection as single aluminum crystals, and the corresponding diagram for the magnesium alloys differed in a manner that suggested that small amounts of magnesium may decrease slightly the stacking fault energy of aluminum. Although poly crystalline aluminum had about the same initial density of dislocations as the single crystals, the density of dislocations increased much more rapidly with strain in the polycrystals. This factor and the higher back stresses generated in the poly crystalline aluminum were the major factors responsible for the higher strength of the poly crystalline aluminum, As the magnesium content of the alloys was increased, the initial density of the dislocations also increased. Most of the alloy strengthening arose from this factor; alloying effects due to short-range order strengthening, Suzuki locking, Cottrell pinning, and so forth, were estimated to be quite small. The gveater rate of strain hardening in the alloys was deduced to be due primarily to the greater increase in the density of the dislocations with strain as the magnesium content was increased. It is the purpose of the present investigation to shed additional light on the average plastic behavior of a grain in a polycrystalline aggregate, by analyses, based on dislocation theory, of appropriate experimental test results. These deductions when compared with those from single-crystal data will then serve to illustrate the major items of difference between the plastic behavior of single crystals and the average behavior of a grain in a

Jan 1, 1963

By W. H. Bassett, J. C. Bradley

Beads of metal frequently appear at the ends of cast-copper wire bars and on the sides of wedge cakes near the top. These are richer in cuprous-oxide than the rest of the casting. A micrographical study of these exudations has been made. 11 is suggested that the materical is forced through the surface while the copper is solidifying. If not eliminated in process of manufacture, it shows on the finished polished sheet copper in patches differing in color from the main body of the shad. Figures 1 to 4 show the copper exudations, at different magnifications, as they appear on the ends of cast wire bars, and on the sides, usually near the top, of wedge cakes. Sometimes the exudations are in fine "drops;" at other times, large masses of the material are found. Microscopic examination of the copper exudation indicates that it is high in oxide and of eutectic proportions. Because of the difficulty of securing a suitable sample, the protuberances have not been analyzed chemically; but the spectroscope shows no indication that there are any more metallic impurities present than in the balance of the copper. The lowest copper plus silver content of the coppers studied for this paper was 99.914 per cent.; the highest, 99.966 per cent.; so the oxygen content of the whole casting would be well under 0.07 per cent. Structure of Protuberances The segregation of oxide between grains in the interior of the cast bar, not far from the "set," is shown in Figs. 5 and 6. In general, the amount of cuprous oxide begins to increase at a point about 0.01 in. below the normal surface of the casting, i. e., the base of the drop; but it does not attain maximum concentration in the main body of the metal. Vertical sections, Figs. 7 to 12, show that there is a definite line of large cuprous-oxide globules at the base of the drops. Horizontal sections at this place show that these large globules lie in a thin billowy

Jan 1, 1926

By Richard O. Carlson

Ions of p31 and B 11 were implanted in natural insulating diamond macles. The thin (-0.4µ) layers showed sheet resistances of 107 to 1011 ohm per sq and activation energies of 0.17 to 0.34 ev above room temperature. However, no Hall effect could be measured, indicating that mobilities were less than I to 10 sq cm per (v-sec). Such low mobilities may be due to excessive scattering due to radiation damage in the bombarded layer or to very high concentrations of active compensating impurities. Annealing did not materially change the room -temperature properties, but the temperature was limited to -800°C by surface graphitization, the latter process probably being accelerated by lattice damage in our diamonds arising from the ion bombardment. A weak n-type thermoelectric power was detected after p31 irradiation, but it cannot be presumed that we have made the phosphorus ions active as donors in diamond. The natural diamonds have a high and uncontrolled concentration of impurities and, when coupled with the radiation damage and graphitization problems, would appear to seriously limit the quality of semiconductor that we can presently achieve by ion implantation in diamond. ALTHOUGH diamonds are usually thought of as insulating in terms of their electrical conductivity, it was found about 15 years ago that natural semiconducting diamonds do occur rarely, and these were designated as type IIb diamonds. These p-type semiconducting diamonds were found to be dominated by an impurity level 0.37 ev from the valence band. Evidence today based on correlation of the concentration of acceptor states from Hall effect measurements with the impurity concentrations determined by neutron activation analysis point to aluminum as the dominant acceptor impurity.' The compensating donor is believed to be nitrogen, which has a donor level 1.6 ev above the valence band.' However, only a small fraction of the total nitrogen content in the diamond is electrically active. An infrared absorption band at 7.8 p and ultraviolet absorption near 4 ev have been associated with nitrogen, the former providing a quantitative measure of nitrogen content.3 The nitrogen content is -l020 cm-3 in insulating or type I diamonds, but is less than 10'' in natural semiconducting diamonds. Much of this nitrogen is distributed in platelets oriented in (100) planes and not atomically dispersed in the diamond lattice.4 Semiconducting diamonds have been deliberately formed by incorporating impurities into the graphite charge in the high-pressure apparatus used to form diamonds.5 These manufactured semiconducting diamonds are always p-type, and while some show the 0.37 ev level due to aluminum, most such samples have been ascribed to impurity banding effects.6 The best natural or manufactured semiconducting diamonds have hole mobilities near 1500 sq cm per (v-sec) at room temperature, and those with the 0.37-ev level can be analyzed to reveal an acceptor concentration of 3 to 8 X 1016 cm-3 and a donor concentration 3 to 10 times lower.' NO bulk n-type diamonds have ever been reported, but the electron mobility has been measured as 1900 sq cm per (v-sec) by irradiating a diamond with ultraviolet to excite electrons out of the deep nitrogen donor level or other levels.7 New hope for the formation of n-type diamond has emerged from the ion-implantation method whereby desired impurities are introduced into a crystal lattice by bombardment with a high-energy beam of the impurity ion. It was found in the case of silicon that the usual donors such as phosphorus and arsenic and acceptors such as boron and gallium could be implanted into silicon. Wentorf and arrow' produced semiconducting layers on diamonds by an ionic bombardment in a glow discharge at potentials of about 2 kv. The observed typeness from thermoelectric probing seemed to depend on the atmosphere gas (nitrogen, argon, or hydrogen) rather than on the electrode material, but the nature of the conduction process in the thin damaged surface layer is completely unknown. A Russian group under Vavilov has attempted high-energy ion implantation in natural diamonds using boron and lithium ions9 and later also phosphorus, aluminum, and carbon ions.10 Their papers claim n-type layers from lithium, phosphorus, and carbon implant and a p-type layer from boron and aluminum implant, though the methods of type determination are not described in detail. Under government contract support, the Ion Physics Corp. has studied ion implantation in several semiconductors. While the bulk of their study1' was devoted to the irradiation of silicon, they did carry out a short study on boron and phosphorus implantation into natural diamonds. They did observe surface conducting layers but did not determine the typeness of the layers. For our experiments, phosphorus and boron were chosen as the dopant ions because of their respective donor and acceptor behavior in germanium and silicon. Moreover, they are the lightest mass dopants of the shallow level donors and acceptors from columns 111 and V of the Periodic Table (excluding nitrogen which is already present in diamond), and will have the largest depth penetration into the diamond lattice. EXPERIMENTAL Diamonds. As the target diamonds for our ion implantation study, we chose commercially available macles, which are flat, twinned diamond crystals. By scanning through the stock of a wholesale distributor

Jan 1, 1970

By B. C. Allen, R. I. Jaffee, D. J. Maykuth

Wrought unalloyed iodide chromium, containing 39 to 95 ppm total interstitials, has a tensile transition temperature of —15°C. Re crystallizing at 1100°C causes the transition to rise to 90° to 390°C, depending on the purity, grain size, and cooling rate after annealing. At about the 100 ppm level, individual additions of carbon or nitrogen raise the transition of both wrought and recrystallized chromium by as much as 210°C, while oxygen has a lesser effect, and sulfur essentially no effect. High transitzon temperatures are exhibited by recrystallized and quenched chromium, and appear to be associated with the amount and distribution of inter-stitials. The latter cm be either in solid solution or in the form of precipitates within the grains or at the grain boundaries. Quench hardening in chromium is primarily caused by nitrogen. The hardness, re crystallization, and grain growth behavior of chromium with and without impurity additions were also investigated. BECAUSE of low density and good oxidation resistance, chromium-base alloys are potentially useful for elevated-temperature applications. The main deterrent to the use of chromium in structural applications is its lack of low-temperature ductility, especially in the recrystallized condition. Accumulated evidence has shown that the ductility of chromium is sensitive to purity. The objective of the current study was to determine the effect of common nonmetallic impurities on the tensile properties of high purity chromium. The separate effects of carbon, oxygen, nitrogen, and sulfur additions on the ductile-to-brittle transition were evaluated for wrought and recrystallized material after various cooling rates. EXPERIMENTAL WORK Unalloyed iodide chromium and seven impurity alloys containing individual carbon, oxygen, nitrogen, or sulfur additions were prepared in rod form. Nominal additions were 100 ppm C, N, and S, and 100 to 500 ppm O. The additions were about a factor of ten greater than the residual amounts in the unalloyed material. The seven alloys and two unalloyed compositions were consolidated into four-pound ingots by conventional consumable arc melting of pressed and welded electrodes under 0.5 atm of helium. Impurity additions were made to the electrode in the form of crushed master alloys. The impurity alloys were double melted to improve homogeneity. The ingots were broken down by extrusion at 1200°C in evacuated steel cans at a reduction ratio of 18 :1, using a molten borosilicate glass lubricant and a ram speed of 80 in. per min. The cans were removed by acid pickling, and the chromium core ground free of surface undulations. Cut lengths were sheathed in mild steel and swaged at 900°C until the core was about 1/4 in. in diam. Two additional 15-lb ingots of unalloyed chromium (ICr-3, ICr-4) were prepared by arc melting and broken down by 26:1 extrusion at 1250°C without a steel can. The billet was lubricated and protected from contamination by a coating of molten glass. The resulting extrusion was then sheath swaged as described previously. Representative chemical analyses of each of the materials, after removal of a 10-mil surface layer

Jan 1, 1963

By K. Mukai, M. Ishihara

This report is a brief discussion of the impurity levels both in primary aluminum and super-purily alnminim in connection with raw materials and proc-essing methods. Particularly, truce amounls of im-purities were analyzed by introducing nittss-speclro-gruphy and nenlron-aclivalian analysis techniques. Vanadium and gallium content in primary aluminum metal corresponded to theor amounls in anode coke. but the nickel content in primary aluminum was hide-pendent oj its amount in the anode cake. Sulfur in the anode colic might result in an increase of the iron content in the molten metal in the reduction cell. The content of sodium and calcium increased with increasing bath ratio. In the holding furnacc sodium content decreased rapidly, and nonmetallic inclusions merit separated front the mollen metal. Three-layer elctrolysis was effectire in eliminating many impuri-ties with the exception of copper, aluminum oxide. aluminum nitride, and some rare-earth elements. THE amount of impurities and nonmetallic inclusions in aluminum metal depends on impurities in the raw materials and various production processes. This paper presents an investigation of the behavior of impurities and nonmetallic inclusions in aluminum during the electrolysis process, the period in the holding furnace, and the process of three-layer electrolysis. Chemical analysis and emission spectrometric analysis have generally been used as methods to determine small amounts of impurities in both primary aluminum and super-purity aluminum; however. mass spectrography and neutron-activation analysis have been recently introduced into this field, and trace amounts of impurities can accurately be determined by these latter methods. EXPERIMENTAL WORK Common impurities were determined by means of absorptiometric. polarographic, flame-photometric. and emission-spectrometric methods. However, in the determination of trace amounts of impurities and non-metallic inclusions, the following methods were applied. In the analyses of trace impurities by mass-spec- trographic analysis, samples were exposed in the vacuum spark of double-focus ing Mattauch-Herzog type mass spectrograph (Japan Electron Optics Laboratory, Ltd.). Ilford Q2 photographic plates were used as ion detectors. Fe was used as the internal standard, and the atomic concentration of each element was calculated by the following expression and converted into the weight concentration: where E, and Ei are the exposures (coulomb) when isotopes of the internal standard and impurity elements (on which the estimate is based) show the same density, X is the percent (atomic) concentration of the standard, IF and Ii are the percent abundances of the isotopes of the standard the impurity elements (on which the estimate is based), and Ms and hfi are the mass of the isotopes of the standard and impurity elements (on which the estimate is based). The coefficient of variation in this method is about 40 pct in the range of 0.1 to 1 ppm. In neutron-activation analysis, irradiations were done in the nuclear reactors TRIGA-I1 (neutron flux: 4.7 x 10 11 n per sq cm per sec; Rikkyo University) or JRR-2 (neutron flux: 2 x 1013 n per sq cm per sec: Japan Atomic Energy Research Institute). After the chemical separation, a NaI (3 by 3 in.) scintillator connected to a 256-channel y-ray spectrometer (R.C.L.) was used for counting and recording various activated impurities. The coefficient of variation in this method is about 20 pct. In the analyses of nonmetallic inclusions, aluminum-oxide determination was carried out according to Fischer's method, 3 as follows. A slice of sample was cut off and the surface was cleaned. It was dissolved in bromine-methanol. The solution was filtered and the residue was washed. The residue was fused with potassium bisulfate flux. Then it was dissolved in weak acid, and oxine solution was added. The aluminum oxinate was extracted with benzene. Finally, aluminum was determined absorptio-metrically. Aluminum nitride determination was carried out as follows. A slice of sample was cut off and the surface was cleaned. It was put in the distillation apparatus and decomposed with sodium hydroxide solution. The solution was distilled. Then ammonia was absorbed and

Jan 1, 1967

By C. S. Matthews, J. L. Mahaffey, W. M. Rutherford

This paper gives results of an experimental study of the sweep efficiency of a miscible displacement in a five-spot. The study was carried out in a parallel-plate glass model in which effects of diffusion were scaled at or near the molecular diffusion level. The experiments show that very early breakthrough (25 to 35 per cent of pore volume (PV) injected) may be expected in miscible floods because of the unfavorable viscosity ratio. However after 1 PV of displacing fluid is injected, the sweep rises to a reasonable value (50 to 60 per cent). Photographs show that small slugs of less than 10 per cent of PV tend to dissipate before breakthrough. A minimum slug size of 15 per cent of PV would appear to be necessary even in a relatively homogeneous formation. Presence of a slug whose viscosity is inter-mediate between that of oil and gas increases the sweep efficiency of the oil-gas system. In a typical system the sweep at breakthrough rose from 26 to 37 per cent of PV for a 25 per cent slug. The increase in sweep brought about by use of a large slug could well pay for the extra deferment cost of the additional slug material. INTRODUCTION Most miscible displacement processes involve the displacement of oil with fluids of much lower viscosity and density. The displacement process at these adverse viscosity and density ratios is dominated by instability phenomena, i.e., viscous fingers and gravity tongues. These phenomena have highly adverse effects on oil recovery. Although a number of laboratory studies have been made to determine the effect of adverse viscosity ratios on five-spot sweep patterns,l,2 the scaling of diffusion effects is uncertain. In the series of scaled model studies reported herein, an attempt was made to scale diffusion. Model studies of miscible displacements in which molecular diffusion predominates are per-mitted by controlling the parallel plate spacing which reduces convective mixing to arbitrarily small levels. To decide how this scaling relates to any particular Geld displacement necessitates an estimation of diffusion effects for the natural rock being considered and conditions under which displacement will be conducted. The approach normally taken is to extrapolate data obtained from stable miscible displacements performed in the laboratory, such as those presented by Brigham et al.3 The validity with which such an extrapolation can be applied to an unstable flow system has yet to be established. If this approach is accepted, a family of oil recovery curves can be generated for a single viscosity ratio based on Brigham's observation that the magnitude of the dispersion coefficient is dependent, among other things, upon specific rock properties. Objective of our test was to define the lower limit of this range by presenting the case where dispersion effects were reduced to the molecular diffusion level in both the transverse and longitudinal directions.

Jan 1, 1967

By Hiroshi Kato, Shin’ichi Nagashima, Hiroshi Takechi

The preferred orientations detleloped during cold rolling, annealing, and hot rolling of low-carbon steel sheets have been investigated by means of an inverse pole figure technique. And X-ray line profile meas-urerrlents were made for the study of the factor which causes the textural changes between cold-rolled and recrystallized sheets. From ND (sheet normal divection) and RD (rolling direction) inverse Pole figures tlze axis detisity change with increasing cold reduction was measured and the Preferred orientations were analyzed. These results can be explained by crystal rotation due to slip during rolling deformation. The ND axis density change during annealing of cold-rollitig sheets is contrary to the change observed in the case of rolling. It was found that the orientation dependency of stored strain energy resulting from cold rolling apparently corresponds to the textural changes during recrystallization. The texture in hot-rolled sheets was found to be influenced by finishing tenlperatltre. In a sheet kol-rolled below the Ar, temperature a significant differernce in texture between the surface and central layers was obtained, the former having {hkl}(111} and {110 )(uvw) orientations and the latter having {pqr}( 110) orientation. A large number of investigations1 6 have been made on the textures of iron and low-carbon steel sheets, and, since it was shown7 13 that preferred orientations are closely related to deep drawability of steel sheets, studies14" 7 on the influence of production processes upon textures have been made from the standpoint of industrial interest. Generally, the textures in low-carbon steel sheets have several components of preferred orientations, but the overlapping of poles makes it difficult to analyze texture quantitatively from pole figures. On the other hand, an inverse pole figure directly expresses quantitative values of components of preferred orientations as the density of a certain sample axis with respect to the crystallite coordinates. Such a texture representation is desirable for a study of deep drawability. The purpose of the present work is to use both inverse and conventional pole figures, with emphasis on the former, to clar~fy the textural changes ~n low-carbon steel sheets by the production processes of hot rolling, cold rolling, and annealing. And the factor causing the textural changes during annealing is studied using an X-ray diffraction line profile technique. EXPERIMENTAL PROCEDURE Sheet specimens for study of cold rolling and annealing textures were taken from a hot-rolled strip of rimmed steel 2.7 mm thick. The chemical composition is shown in Table I. Although the study of cold-rolling textures requires a suitable material with random orientation, it is difficult to produce a perfect random one. But the used specimens, obtained from the hot-rolled strip with a finishing temperature higher than Ar3, were nearly random, such as shown in Fig. 15. These were cold-rolled to various reductions by a 4-high rolling mill with 150-mm-diam work rolls and 300-mm-diam backup rolls. The influence of hot-rolling conditions such as finishing and coiling temperatures on textures of hot-rolled strips was studied. The chemical compositions of these hot coils are given in Table I1 and the hot-rolling conditions are given in Table 111. inverse Pole ~i~ure -~easurement. Two methods for determining inverse pole figures with high precision have been proposed. The first, by Jetter et a1.,18 consists of obtaining mean densities of divided regions in a unit stereographic triangle by solving simultaneous linear equations to approximate the integral relation between conventional and inverse pole figures. The second, proposed by ~oe'~-'~ and Bunge,22'23 consists of determining an expanded series of spherical surface harmonics which express axis densities from several sets of pole distribution data. Both methods require laborious numerical calculations which make them unsuitable for practical use. However, the axis densities of the locations corresponding to low Miller indices in a unit stereographic triangle can be obtained

Jan 1, 1969

By Thomas Kesler

THE Cartersville mining district, 35 miles northwest of Atlanta, Ga., has been of varying but continuous importance in the southern mineral industry during the past century. Noted chiefly for its production of brown iron ore, manganese oxide ores, barite, sienna, and magnesian limestone, the district and its environs have produced brick and tile clays, slate, gold, bauxite, and graphitic schist. Minor deposits of serpentine, sericite schist, copper ore, and red iron oxide have been prospected. The obvious deposits of brown iron ore, together with some associated specular hematite, were mined out years ago, although a little ore was left in the workings. Moderately steady production of sienna reached a peak about 1930, then declined rapidly. Manganese mining passed through a relatively active period from the World War to 1931, but has subsided to a small but rather constant output for the Birmingham market. How-ever, the White Manganese Corporation has prepared for possible increased production by constructing a new washer capable of handling about 300 tons of ore per day. Principal activity in the district proper has centered for some years in the production of barite and magne-sian limestone.

Jan 1, 1940

Report of the Secretary TO THE BOARD OF DIRECTORS AND THE MEMBERS OF THE AMERICAN INSTI¬TUTE OF MINING AND METALLURGICAL ENGINEERS GENTLEMEN As will be shown by the special reports of the Finance, Membership, Library, Papers and Publications, Increase of Membership, and other standing Committees, together with that of the Treasurer, the year 1927 was one in which the Institute made very satisfactory progress in a number of directions. In total numbers the membership is no larger but in revenue from dues there has been a marked increase. This has been due to the promotion to full membership of Junior Associates of earlier years, to the larger proportion that come in originally as members rather than juniors, and to the keener interest in the work of the Institute reflected in prompter payment of dues. The latter is important, since experience shows that of those who fall behind a large number must ultimately be dropped for non-payment. Conditions in the mining in¬dustries have been healthy though not booming. It has been much easier for members to find employment and meet their financial obligations but there has not been that flow of young men into mining, and hence in part into the Institute, that characterized certain earlier years. Rather the tendency toward centralization and larger industrial units has re¬stricted the number, though not the scope, of opportunities for technical men in the mineral industries. The Institute is constantly receiving resignations from members crowded out of mining into other lines of activity. On the other hand, those who remain in mining and metal¬lurgy have a greatly increased necessity for information and contacts with technology. A few years ago many superintendents and most foremen were non-technical men. Today the reverse rule obtains and shift bosses and men who occupy even lower positions in industrial units are called upon to know and to apply such an amount of technical knowl¬edge that graduate engineers are the rule rather than the exception. The curious situation has obtained that with a much smaller enrollment of students in the schools of mining and metallurgy there has been at times an actual shortage of young engineers for beginners' jobs. The young men retort that the conditions of employment and pay offered in mining are not equal to those in other lines and, while it is undoubtedly true that the young engineer beginning in mining is able to start under conditions markedly better as to pay, living, and responsibility than did the men who are now leaders, they are required to know much more and have usually spent more in time and money to qualify for their jobs. The whole matter is one which warrants much more attention than has been given to it. For the Institute it is important since the young men

Jan 1, 1923

By John Griffen

THEORY HYDRAULIC classification as explained by Rittinger and others was largely restricted to conditions wherein the free-falling velocities of the particles were conceived as governing the separations effected (see chapter 9). The laws governing classification under free-falling conditions have been summarized by Chapman and Mott as fo1lows:l Nomenclature r represents, in a particle of irregular shape, the round-hole screen through which the particle would pass, or some other linear dimension of the particle equivalent to d, the diameter of a sphere. s, the specific gravity of the particle. 1, the specific gravity of the water used as a medium. K, a constant. W, the velocity of the water. In an Upward Current of water 1. A particle will move upward if [V > K dr(s - 1)] and, by suit- ably regulating the speed of the water current, the larger and heavier particles may be made to fall downward against the current, leaving the smaller, lighter particles in suspension in the current. 2. Particles such that [- = -] cannot be separated in an upward- current classifier with any one velocity of current. Coal particles having a specific gravity of 1.35 cannot be separated from refuse particles of [2.5 - 1 2.5 sp. gr.] unless the ratio of diameters is less than [ 4.3 to 1, 1.35 – 1] and the raw coal must be screened to size limits within this ratio if they are to be separated. Cone-shaped vessels or vessels of other shapes that allow the use of different velocities of current at different points in the flow are used to modify this limitation.

Jan 1, 1943

By Herbert Clark Hoover, Lou Henry Hoover

DIFFERENT methods of parting gold from silver, and, on the other hand, silver from gold, were discussed in the last book; also the separation of copper from the latter and further, of lead from gold as well as from silver ; and, lastly, the methods for refining the two precious metals. Now I will speak of the methods by which silver must be separated from copper, and likewise from iron.1 The officina, or the building necessary for the purposes and use of those who separate silver from copper, is constructed in this manner. First, four long walls are built, of which the first, which is parallel with the bank of a stream, and the second, are both two hundred and sixty-four feet long. The second, however, stops at one hundred and fifty-one feet, and after, as it were, a break for a length of twenty-four feet, it continues again until it is of a length equal to the first wall. The third wall is one hundred and twenty feet long, starting at a point opposite the sixty-seventh foot of the other walls, and reaching to their one hundred and eighty-sixth foot.

Jan 1, 1950

By Michael H. Kuryla, Galen H. Clevenger

Some years after Nobel made his epoch-making contribution to the knowledge of high explosives, Sprengell described a new class of detonating explosives consisting of mixtures, made immediately before use, of an oxidizing agent and a combustible substance.2 The novel feature of the Sprengel explosives is that the constituents alone are non-explosive during manufacture, storage and transport. Despite this advantage, and although some of these have been used in important work, they are now little used, possibly on account of the greater inconvenience to the user, compared with explosives supplied by the manufacturer in final form. Liquid-oxygen explosives are a type of Sprengel explosive in that the oxidizing agent (liquid oxygen) and the combustible substance or substances (solid carbonaceous matter alone or in combination with liquid hydrocarbons or even metallic powders and, at times inert absorbents) are brought together immediately before use. The components separately are non-explosive. The possibility of using liquid oxygen as one of the components of an explosive was perhaps first suggested by Sprengel, who stated that the beau ideal of a detonating explosive was a mixture of eight parts of liquid oxygen with one part of liquid hydrogen. Although the liquefaction of air3 had been accomplished in the laboratory as early

Jan 1, 1923

By Michael H. Kuryla, Galen H. Clevenger

Some years after Nobel made his epoch-making contribution to the knowledge of high explosives, Sprengell described a new class of detonating explosives consisting of mixtures, made immediately before use, of an oxidizing agent and a combustible substance.2 The novel feature of the Sprengel explosives is that the constituents alone are non-explosive during manufacture, storage and transport. Despite this advantage, and although some of these have been used in important work, they are now little used, possibly on account of the greater inconvenience to the user, compared with explosives supplied by the manufacturer in final form. Liquid-oxygen explosives are a type of Sprengel explosive in that the oxidizing agent (liquid oxygen) and the combustible substance or substances (solid carbonaceous matter alone or in combination with liquid hydrocarbons or even metallic powders and, at times inert absorbents) are brought together immediately before use. The components separately are non-explosive. The possibility of using liquid oxygen as one of the components of an explosive was perhaps first suggested by Sprengel, who stated that the beau ideal of a detonating explosive was a mixture of eight parts of liquid oxygen with one part of liquid hydrogen. Although the liquefaction of air3 had been accomplished in the laboratory as early

Jan 1, 1923