Search Documents

Upon the recommendation of its Technical Committee, The Com-pressed Air Society has adopted the following definitions of, certain terms. Displacement.-The displacement of an air compressor is the volume displaced by the net area of the compressor piston. Capacity.-The capacity should be expressed in cubic feet per minute, and is the actual amount of air compressed and delivered, expressed in terms of free air at intake temperature and at the pressure of dry air at the suction. Volumetric Efficiency.-Volumetric efficiency is the ratio of the capacity to the displacement of the compressor, all as defined above. Compression Efficiency.-Compression efficiency is the ratio of the work required to compress isothermally all the air delivered by an air compressor to the work actually clone within the compressor cylinder, as shown by indicator cards, and may he expressed is the product of the volumetric efficiency (the intake pressure and the hyperbolic logarithm of the ratio of compression), all divided by the indicated mean effective pressure within the air cylinder or cylinders.

Jan 8, 1918

By Donald H. McLaughlin, John H. Moses

IN the latitude of Lima, the broad uplifted block that forms the Andes is made up of a complex sequence of folded and faulted sediments and volcanics, broken by large and small bodies of granitic rocks and porphyries with which the principal mineral deposits are closely associated in both time and space. The intrusives are a final episode in the geologic history as revealed by the consolidated rocks, for after their emplacement and after the formation of the primary ore deposits in and about them the record is simply one of long continued erosion and uplift.

Jan 1, 1945

By William Mikulas

LITTLE work has been done in the field of the nickel-tin binary system. The complete diagram has been investigated on two occasions, but the results are in very poor agreement. The structure of a compound NiSn, and the solubility of tin in nickel have been determined by X-ray methods. Several investigations have been made of the liquidus curve, and the compositions of the eutectics have been determined. A study of the literature, however, shows that there is no satisfactory agreement between the data presented in the various papers. The present investigation was undertaken in an attempt to determine the equilibrium conditions, and to correlate X-ray with metallographic data. The equilibrium diagram was determined by thermal and metallo-graphic means, and the solubility of tin in nickel further investigated with X-rays. Powder diagrams were made of the intermetallic com-pounds, and three of the structures were partly determined. No attempt was made to determine the range of homogeneity of the inter-metallic compounds.

Jan 1, 1937

By W. R. Barclay

IN MY general contact with industry I have become more and more impressed with the need for the closest possible co-operation between engineers and metallurgists, and particularly with the need for appreciation of the work that each group is doing to assist the other. Also, I am convinced that from time to time it. is vitally important to a true perspective of human progress in all its branches, and certainly a salutary corrective of undue optimism and pessimism to endeavor to carry the mind hack over certain periods in the advance of technical knowledge, and form some kind of broad estimate of what has been accomplished in the application of science to industry in the fields with which we, as individuals or groups, may for the time being be concerned. We cannot without some appreciable mental effort realize what our forerunners have dine For us. If the young engineer or metallurgist entering industry today could be suddenly transported to a quarter of a century ago, and be compelled to work with the materials then available and within the limitations of knowledge then attained, he would, on his return to present-day life, have a much greater appreciation of what has been accomplished before lie arrived on the scene, and, what is even more important, a far more acute sense of its inherent value to his profession. I propose here merely to indulge in a general summary of the subject of improved engineering metals and alloys rather than in details, and to deal exclusively with developments within my own experience.

Jan 1, 1938

By J. H. Nead, T. S. Washburn

The grades of commercial steel produced in large quantities can be divided into two general types from the standpoint of ingot structure— killed and rimmed. Killed steel covers a wide variety with carbon contents throughout the range of the steel portion of the iron-carbon diagram, and is the kind usually used in the production of alloy steels. Rimmed steel is normally associated with carbon ranges under 0.30 per cent, and is not yet used to a large extent in alloy practice, except for copper-bearing steels. The fundamental differences in the ingots made from these two types of steel can be seen most easily in Figs. 1 to 7. In the rimmed ingot shown in Figs. 5 to 7 there are two lines of blowholes approximately parallel to the sides and coming together at the top and at the bottom of the ingot. In the killed ingots shown in Figs. 1 to 4 these blowholes arc not present. Also, the rimmed ingot has no well defined pipe, as compared to the deep pipe on the killed ingots, and there are numerous primary blowholes in the lower portion of the rimmed ingot perpendicular to the surface and close to it, while on the killed ingot there are no blowholes of this type in the ingot shown in Fig. 1 and very small ones close to the surface in the lower part of the ingot shown in Figs. 2 to 4. With respect to the presence of pipe and the primary blowholes, the structure may vary considerably in both rimmed and killed ingots, therefore these cannot be considered as fundamental structural characteristics differentiating the two types of steel. The primary blowholes in rimmed ingots may be much less pronounced than those in the ingot shown in Figs. 5 to 7—as, for example, in "ingot iron," which is entirely free from them. An example of a cross section of an ingot-iron ingot is shown on page 16 of "Research and Methods of Analysis of Iron and Steel," published by the American Rolling Mill Co. (1920). A certain amount of pipe may also occur in rimmed ingots, though it is normally porous and not as well defined [or deep as in the killed ingot of Fig. 1. In killed ingots, primary blowholes may occur near the surface, as in Figs. 2 to 4, and

Jan 1, 1937

There were two official representatives of Foreign Governments as guests at the Chicago Meeting. One was Frederick Goransson, managing director of the Saudvikens Steel Works, who represented the Jernkonteret, the Iron and Steel In-stitute of Sweden, and who came to this country especially for our meeting. The other distinguished guest was Commander Toublet, who repre-sented the French Embassy. Commander Toublet delivered a most polished address at the Banquet, dealing with the felicitous relations existing between this country and France for the last 150 years. Com-mander Toublet was accompanied by Mrs. Toublet, who won the hearts of all the ladies present, whose guest she was.

Jan 11, 1919

By Robert E. Green, T. Hinton

Expressions are derived for tke orientation factors appearing in the Grana to -Lucke theory of dislocation damping, for fcc crystals. The factors are given as functions of the elastic constants, the direction cosines of the specimen axis, atld the direction cosines of the particle displacemeizts, for darnping due to dislocation motion on each of the twelve possible slip systems as ixell as lor simultaneous dislocation rnotion on all twelve systems. RECENTLY Green' has outlined the general procedure for calculation of the modes of wave propagation in a single crystal possessing a given crystallo-graphic orientation. In addition he has suggested how the results of such calculations along with calculations of the resolved shear-stress factors for slip enable the orientation-dependent factors (orientation factors) appearing in the Granato-Lucke theory of dislocation damping to be calculated. However, reen' assumed that the maximum stress on dislocations was in the direction of the particle displacement of the elastic wave giving rise to the dislocation damping. The present cal'culations show that this is an oversimplified approach appropriate only to special cases of high crystallographic symmetry. The exact calculation of stress on the dislocations can only be obtained by resolving the nine components of stress associated with the elastic wave into the appropriate slip direction and then summing. In this paper the general expressions for orientation factors are derived for fcc crystals in terms of the elastic constants, the direction cosines of the particle displacements, and the direction cosines of the specimen axis, bearing in mind the point mentioned above. Equations are presented which give the orientation factors for damping due to dislocation motion on each of the twelve possible slip systems as well as for simultaneous dislocation motion on all twelve systems arising from elastic-wave propagation. These orientation factors are appropriate to attenuation measurements made by the pulse-echo technique, where the elastic wave is a traveling wave. They will be compared with those for the case of a standing wave as derived by Granato and Lucke which are appropriate to measurements of internal friction by the resonance technique. The expressions for the orientation factors are compared with the five values given by insruch,' based on unpublished work of Granato and Liicke, for positions of highest symmetry in the stereographic triangle. The various equations derived for modes of wave propagation and orientation factors have been evaluated for the case of aluminum crystals at 1-deg intervals throughout the stereographic triangle. These results will be presented in the form of contour diagrams in a subsequent paper3 and their relevance to ultrasonic measurements discussed. ORIENTATION FACTORS The coordinate system used for the calculations is shown in Fig. 1 and all specimen axes are taken to lie in the shaded standard triangle. The twelve slip systems are indexed according to Table I. Following the suggestion of lers, we may define the orientation factor Ok in the Granato-Liicke theory5 by the equation

Jan 1, 1967

By J. H. McCormick

This plant, near Marysville, Mont., was planned to treat the ore from the Piegan and Gloster mines, the latter being one of the early and famous producers of the Marysville district. When the mill was closed in 1888, treatment consisted of stamp milling, followed by pans and settlers for pan amalgamation. The extraction was evidently poor, because, a few years later, thousands of tons of tailings were re-treated by the ranchers in the valley below the mill, by the then new cyanide process, and gave a handsome profit. In 1914, the present owners, after laboratory tests and an experimental mill run, decided upon the following treatment: crushing to 40 mesh in cyanide solution, concentration, amalgamation, classification, and cyani-dation of sands by leaching, and of slime by agitation and decantation in charges. The ore averaged about $7 per ton, gold and silver, the ratio of weight being 1 oz. gold to 7.56 oz. silver. The ratio of gold and silver in tailings was 1 oz. Au to 36.6 oz. Ag; the quartz was sharp and sandy, however finely ground, and rather difficult to slime. The mechanical equipment was a No. 5 Symons gyratory crusher; three 10-ft. Lane slow-speed Chilean mills; one Wilfley roughing and one finishing table; one submerged-type Akins classifier; five 26 by 10-ft. fir leaching tanks; one 24 by 7-ft. Dorr thickener; four 14 by 16-ft. Dorr agitators; four 6-compartment double-row zinc-boxes having compartments 18 in. wide, 18 in. deep, and 34 in. long; Johnson zinc lathe; acid and vacuum filter tanks for treating precipitate; roasting furnace; and Case tilting No. 275 crucible furnace for melting precipitate. The mill is driven by electric power supplied by the Montana Power Co. at the following rates, per kw.-hr.: 200 to 300 hp., 0.68 c.; 300 to 500 hp., 0.61 c.; 500 to 750 hp., 0.55 c.; plus $1 per month per installed motor horsepower. The plant as above described was operated from May, 1915, to the end of the year, when an additional Dorr thickener and a 12 by 12-ft. Portland revolving filter were added, increasing the nominal capacity of 100 tons per 24 hr., but not the percentage of extraction. The combined treatment, at a cost of $1.48 per ton, saved 90 per cent. of the gold arid

Jan 1, 1919

By E. H. Dix

The work of Merical and other investigators indicates that the phenomenon of age-hardening in alloys of the duralumin type is primarily dependent upon the variation in the solubility of copper with temperature. In addition to copper, however, these alloys contain small amounts of magnesium, silicon, manganese and iron, which may affect the age-hardening either directly or indirectly. The effect of these elements on the solubility of copper and on the manner in which this solubility varies with the temperature is of considerable interest, therefore. The effect of magnesium is of especial interest because apparently it exerts a marked effect on the natural or room-temperature aging of alloys of the type described.2 A series of investigations3 has been in progress in the research laboratories of the Aluminum Company of America to determine the functions * Metallurgist, Aluminum Research Laboratories. f Metallurgical Division, Aluminum Research Laboratories. Formerly with Metallurgical Division, Aluminum Research Laboratories. 1 P. D. Merica, It. G. Waltenberg and H. Scott: Heat Treatment of Duralumin. U. S. Bur. Stds. Sn. Paper 347 (1910). 2 M. Gayler: Constitution and Age-Hardening of Alloys of Aluminum with Copper, Magnesium, and Silicon in the Solid State. Jnl. Inst. Met. (1922) 28, 213. W. Fraenkel: Vergutbare Aluminiumlegiengen. Ztsch. Melallkunde. (1920) 12, 427. E. H. Dix, Jr.: Note on the Microstructure of Aluminum-Iron Alloys of High Purity. Proc. Amer. Soc. Test. Mat. (1925) 26, Pt. 2, 120. E. H. Dix, Jr. and H. H. Richardson: Equilibrium Relations in Aluminum-copper Alloys of High Purity. Trans. A. I. M. E. (1926) 73, 560. E. H. Dix, Jr. and W. D. Keith: Equilibrium Relations in Aluminum-manganese Alloys of High Purity. Proc. Inst. Met. Div., A. I. M. E. (1927) 315. E. H. Dix, Jr. and A. C. Heath, Jr.: Equilibrium Relations in Aluminum-silicon and Aluminum-iron-silicon Alloys of High Purity. Proc. Inst. Met. Div., A. I. M. E. (1928) 164. E. H. Dix, Jr. and F. Keller: Equilibrium Itelations in Aluminum-magnesium Alloys of High Purity. Proc. Inst. Met. Div., A. I. M. E. (1920) 351. E. H. Dix, Jr., F. Keller and R. W. Graham: Equilibrium Relations of Aluminum-magnesium Silicide Alloys of High Purity. Trans. A. I. M. E., Inst. Met. Div. (1931) 404. W. L. Fink and K. R. Van Horn: Constituents of Aluminum-iron-silicon Alloys. Trans. A. I. M. E., Inst. Met. Div. (1931) 383.

Jan 1, 1932

By Charles M. Rolker

The Mariposa estate, a grant made by the Mexican Government to Juan 13. Alvarado, during the time when California was still under the dominion of Mexico, was purchased in 1847 by J. C. Fremont, and the United States patent issued to him in 1856. By sale, or its equivalent, money advanced, the property came into the hands of the Mariposa Company, June 25th, 1863, and through a varied existence of work and temporary inactivity, has as yet been kept as an undivided property, and rests at present with the Mariposa Land and Mining Company of California. I pass over this period of 15 years without giving the history of the ups and downs of the estate, partly because it is familiar to many, and also because I think in such a case this paper would assume too much the character of a narrative. The estate is situated in Mariposa County, California, about 170 miles southeast of San Francisco. It begins in lat. 37' 26' 38'' north, and long. 119' 55' west, and runs 6 miles north; thence 69 miles west; thence 5 miles northwesterly towards the Merced River; thence 84 miles southerly; thence 3 miles easterly; thence 1 mile southerly; thence 2 miles easterly; thence 2 miles southerly; thence 2 miles easterly; thence 1 mile southerly; thence 2 miles easterly; thence 1 mile northerly, and thence 2 miles easterly to the place of the beginning; embracing 44,387 acres (70 sq. miles) more or less. To describe this vast estate in detail as to its full geology, its numerous quartz veins, its many facilities to exploit them and work them by cheap methods, would lead me further than I intend to go at present, and I will content myself to describe the latest workings of the company and its immediate field of operations. As long ago as 1860 the late Dr. Adelberg advised the running of an adit from the northwestern edge of the estate at Benton Mills 011 the Mereed River. His object was to undercut the deepest workings of the then paying mines on the estate—the Pine Tree and Josephine. Following this advice, the tunnel known as "River Tunnel " was commenced. Its entrance is in S. 5, T. 4, s. R. 17 E. It is run in

Jan 1, 1879

J. J. MCLELLAN, Webb City, Mo.-The Media mill, at the time it was built, was the largest mill that had been designed in the Joplin district. It was put up in a hurry, to take advantage of the high prices for zinc ore in 1915, by the owners of an adjacent plant, which had been very profitable. They owned a compound Corliss engine, and to take advantage of a single-unit drive it was necessary to build the mill in the form chosen, which involved making the hopper feed directly through the breakers and rolls, the undersize from the screen passing at once to the jigs, the oversize going through the rolls and returning to the original trommels. The mill was built in fairly good proportion; crushing was done by jaw breakers, Webb City pattern,' and three sets of 42-in. (106.7-cm.) Cornish rolls for reducing the oversize. The jigs were larger than the usual practice. The roughers were two six-cell jigs, with 42 by 48-in. cells. The cleaner jig was the largest ever constructed in the district up to that time, having seven 36 by 48-in. cells, for treating the rougher jigs. There was also a chat rougher. "Smittem," as used in our district, is the partly concentrated product from the rougher, which is finished on the cleaner jigs. "Chats" are the middlings proper, that is, they are the grains of chert with included particles of sulphide; the very low-grade smittem is sometimes included among the chats. When drawing chats from a jig, we also draw about ten times greater quantity of barren chert in order to insure complete recovery of mineral. This mixture of middlings and tailings is taken to a set of 30-in. rolls, the crushed product then going to a chat rougher, a comparatively small jig, with 26 by 36-in. cells. The principal departure of the Media mill from the usual practice was to build a hopper sufficiently high to give gravity feed to the jigs, without using elevators. The sludge plant, for table treatment of sand and slime, also contained several innovations in the manner of distributing the feed. The tables were arranged in two rows and the feed ran around the outside in a launder having two or three cone classifiers

Jan 1, 1918

By J. P. Kerr, W. H. Cordell

Conditions in the oil and gas industry in Indiana were about the same in 1935 as in 1934. This is especially true of the old Trenton area and the Harrison County area where production was steady and almost no exploration and development took place. The past year has seen an increase in drilling activity and a decrease in oil and gas output in southwestern Indiana. In the state, 224 wells were completed in 1935, of which 48 were oil wells, 61 gas wells, and 115 dry holes. A few of these were old gas wells deepened to oil horizons. Twenty-six wells started during 1935 were not completed by Dec. 31. Approximately one-half the wells drilled were within proven areas. A relatively large number of wildcats, especially in Daviess, Pike and Gibson Counties, were in search of new gas supplies to supplant the diminishing resources in those counties. The decreased production of gas was due largely to the fact that existing supplies declined more rapidly than new fields could be brought on. The Alford field, in Pike County, which produced the bulk of the supply in 1934, was called on to do likewise in 1935, but was unable to respond sufficiently to keep up the yearly production for southwestern Indiana. During the last half of the year, the Oaktown field, Knox County, was connected with one of the principal pipe lines of the state, which helped to keep gas production above an unusual low. The decline in oil production was due almost entirely to proration during the first eight months of the year. The proration affected Daviess, Pike, Gibson, Sullivan and Vigo counties, which produce about three-fourths of the total for the state. After proration was lifted, the wells never quite reached the conditions existing before proration. The average daily production per well in Indiana is less than two barrels. The outstanding development in Indiana in 1935 was the drilling in the Oaktown field immediately before and after the laying of the 6-in. pipe line to the field. Almost without exception the wells came in with an open flow of two to four million cubic feet. At the end of the year, 26 wells were connected to the pipe line. Development of this field will

Jan 1, 1936

By J. P. Kerr, W. H. Cordell

Conditions in the oil and gas industry in Indiana were about the same in 1935 as in 1934. This is especially true of the old Trenton area and the Harrison County area where production was steady and almost no exploration and development took place. The past year has seen an increase in drilling activity and a decrease in oil and gas output in southwestern Indiana. In the state, 224 wells were completed in 1935, of which 48 were oil wells, 61 gas wells, and 115 dry holes. A few of these were old gas wells deepened to oil horizons. Twenty-six wells started during 1935 were not completed by Dec. 31. Approximately one-half the wells drilled were within proven areas. A relatively large number of wildcats, especially in Daviess, Pike and Gibson Counties, were in search of new gas supplies to supplant the diminishing resources in those counties. The decreased production of gas was due largely to the fact that existing supplies declined more rapidly than new fields could be brought on. The Alford field, in Pike County, which produced the bulk of the supply in 1934, was called on to do likewise in 1935, but was unable to respond sufficiently to keep up the yearly production for southwestern Indiana. During the last half of the year, the Oaktown field, Knox County, was connected with one of the principal pipe lines of the state, which helped to keep gas production above an unusual low. The decline in oil production was due almost entirely to proration during the first eight months of the year. The proration affected Daviess, Pike, Gibson, Sullivan and Vigo counties, which produce about three-fourths of the total for the state. After proration was lifted, the wells never quite reached the conditions existing before proration. The average daily production per well in Indiana is less than two barrels. The outstanding development in Indiana in 1935 was the drilling in the Oaktown field immediately before and after the laying of the 6-in. pipe line to the field. Almost without exception the wells came in with an open flow of two to four million cubic feet. At the end of the year, 26 wells were connected to the pipe line. Development of this field will

Jan 1, 1936

By W. H. Morris

I have been requested to present a paper on the slag from the basic Bessemer process, as prepared for fertilizing. Since Professor W. B. Phillips presented at the Birmingham meeting, in May, 1888, an able paper* on this subject, as it had been developed up to that time, there is little for me to add. Perhaps later practice may be best expressed by the homely proverb, " The proof of the pudding is in the eating." As the Pottstown Iron Company is the only concern manufacturing basic Bessemer slag in this country, the writer's personal experience in the use of it may be interesting. Our slag averages: P2O5, 21.37; SiO2,, 5.10; MgO, 5.90; Al2O3, 4.01; MnO, 5.56 ; FeO, 12.00; Na2O and K2O, 0.80; CaO, 45.26; total, 100.00. This gives over 76 per cent. of phosphoric acid and lime. In using this material for several years past on my lawn and garden, I have found it better than anything else I have ever tried ; and I am sure that any of you who had seen my green grass last month (January), wherever the ground was bare from snow, as bright as in early fall, would be forced to acknowledge the advantages of this soil-enricher. The grass on my private lawn, and around the company's office, is green the whole winter; and we have raised very good sod, by the use of this phosphate, where, without it, we were unable to get the grass to grow either from seed or by repeatedly sodding. The same statement applies to garden-truck; when the soil was first broken up, a good crop of vegetables was easily raised. My own gardener has had several premiums from Philadelphia seedsmen (notably, last year, the first premium for sugarcorn raised in the first part of July, being the first sample sent them). Our method of applying this material is to grind the slag very finely, so that at least 60 per cent. of it will go through a 150-mesh screen (i.e., say, 22,500 meshes to the square inch), and 90 per cent. through a 100-mesh screen (i.e., 10,000 meshes to the square inch). This fine grinding seems to be the main condition of success.

Jan 1, 1893

By David A. Keys

The object of this investigation was to determine with a vertical magnetic variometer the extent of the titaniferous ore deposit that occurs not far from Ivry in Terrebonne County, Quebec, about 70 miles north of Montreal. The Ivry mine, on lots 37 and 38 of range V, Beres-ford township, Quebec, is one of the largest and most accessible to transportation of the deposits of ilmenite in Quebec. The ore consists of an aggregate of ilmenite anhedra serving as host for numerous fine plaques of hematite. No magnetite is known from any occurrence near this lot, and in this way the deposit differs from many others that contain a large percentage of magnetite with the ilmenite. The deposit at Ivry thus has much lower magnetic susceptibility than those containing abundant magnetite, and a sensitive magnetometer was necessary for the work, although a body of magnetite with ilmenite about a mile from the Ivry mine was successfully prospected with a dip needle. The principal orebody is exposed in a quarry known as the Ivry mine, from which about 16,000 tons of ore have been shipped. Small exposures of ilmenite isolated by drift serve to show the presence at the surface of some of the bodies indicated by the magnetometer, but most of the hill is covered with glacial till and second growth hardwood. At the lower levels the till gives place to fluvioglacial sands and gravels from which the forest has been cleared. The increasing thickness of the sand and gravel as the hill descends makes the tracing outward of the deposits from the rocky knob of anorthosite a difficult matter. Within the orebodies too, some masses of anorthosite persist, which may account for some local irregularities. Fig. 1 is a photomicrograph, taken by reflected light, of a typical specimen of the ore. The dark patches are hematite and the light parts are ilmenite No trace of magnetite was found. Pig. 2 is a photomicrograph of a thin section of the country rock showing the texture of the anorthosite. The mean of four analyses quoted by Robinson1 is: titaninm, 19.26 per cent; iron 45.41 per cent. The ilmenite ore is not sufficiently magnetic to deflect an ordinary compass needle, but the effects of the induced magnetism in the ore by

Jan 1, 1940

By Elmer R. Kaiser

G. A. Vissac (Consulting Engineer, Vancouver, B. C.) —Some of the data presented in this paper, in connection with cost studies of washed coals, should be clarified and qualified. Washing a raw coal down to a low ash content may mean higher losses in refuse, but the cost of the operation may be more than compensated by the increased value of the resultant product. However, careful engineering and accurate machinery are required to insure maximum profits. Washing at a low gravity separation demands a very accurate automatic process, chiefly when the small sizes of coal are being handled. Coal consumers today are buying mostly on a Btu basis, cognizant of the fact that low ash contents result in lower installation costs and in savings in handling and transportation charges. The attached Table X gives the actual balance sheets of the various cleaning operations corresponding to various ash contents for the two coals presented in the paper, using the old technique of a two-products separation. or the new technique, now commonly used in Europe, of a three-way separation made possible by new methods and new equipment. Savings in capital costs, handling, and transportation have been calculated on the basis of a delivered cost f.O.b. plant of $10.00 per ton of coal at 16.5 pct ash (actual 1953 average price reported by Consolidated Edison, N. Y.), and of $3.50 at the mine also for 16.5 pct ash coal. In both cases this corresponds to values of 126 and 4.26 per 1 pct of combustible and per ton, respectively, on delivered and on at the mine prices. As an example, the middle western coal at 16.5 pct ash, raw, washed down to 4 pct ash in a two-way process will give 53.75 pct of clean coal at 4 pct ash and 46.25 pct of refuse at 31 pct ash. The value of the losses will be 0.4625x(100—31)x0.042 = $1.34. Add the cost of washing, capital, and operation, which is $0.35. The total cost will then be $1.69. But with a three-ways separation we will have 53.75 pct of first-grade coal at 4 pct ash, 37.25 pct second-

Jan 1, 1955

By R. B. Newcombe

Despite abnormal economic conditions and the unhealthy state of the petroleum industry, 1930 closed without any marked decline in total production of oil in the Middle Western States. The most accurate figures available would indicate for this district an output of close to 25,000,000 bbl. for 1930 as compared to 26,000,000 bbl. for 1929. This can be accounted for by the settled nature of a great many of the wells producing in this area and the favorable geographical position, which affords adequate refining and marketing facilities. The only new flush production field discovered in the area was the Legrande oil pool in southeastern Hart County in western Kentucky, where wells up to 1000 bbl. initial have been reported from a shallow depth. Important extensions have been found in a number of central Ohio fields, and activity in the central Michigan area resulted in new pools along the northwest trend of the Mt. Pleasant structure. These new districts, known as the Leaton and Vernon pools, have not yet reached the scope of the Mt. Pleasant field proper, and although the structure is similar, sand conditions are not strictly analogous. Wildcatting was retarded somewhat by the scarcity of market for oil and many important wells were shut down for several months. This has not shown such a profound effect on production as the reticence of operators to drill inside proven locations. The major companies have not been able to dispose of their oil and the smaller operating units are having trouble financing their projects. The result is that oil in sight is not being produced and output is suffering accordingly. Another important effect on production was the introduction of proration by the major crude purchasers and a voluntary shut-down by Kentucky operators. This step became necessary because of the glutting of lake port refineries with Mid-Continent oil, and was not fostered by regulating state bodies, as in the case of the southwestern states. Small refining units have sprung up to meet this situation in a number of instances but they have experienced some difficulty in disposing of their product because of "dumping" tactics from other quarters. New refinery outlets on the Great Lakes and new pipe line connections should tend to alleviate this difficulty during the coming year. The

Jan 1, 1931

By David A. Keys

The object of this investigation was to determine with a vertical magnetic variometer the extent of the titaniferous ore deposit that occurs not far from Ivry in Terrebonne County, Quebec, about 70 miles north of Montreal. The Ivry mine, on lots 37 and 38 of range V, Beres-ford township, Quebec, is one of the largest and most accessible to transportation of the deposits of ilmenite in Quebec. The ore consists of an aggregate of ilmenite anhedra serving as host for numerous fine plaques of hematite. No magnetite is known from any occurrence near this lot, and in this way the deposit differs from many others that contain a large percentage of magnetite with the ilmenite. The deposit at Ivry thus has much lower magnetic susceptibility than those containing abundant magnetite, and a sensitive magnetometer was necessary for the work, although a body of magnetite with ilmenite about a mile from the Ivry mine was successfully prospected with a dip needle. The principal orebody is exposed in a quarry known as the Ivry mine, from which about 16,000 tons of ore have been shipped. Small exposures of ilmenite isolated by drift serve to show the presence at the surface of some of the bodies indicated by the magnetometer, but most of the hill is covered with glacial till and second growth hardwood. At the lower levels the till gives place to fluvioglacial sands and gravels from which the forest has been cleared. The increasing thickness of the sand and gravel as the hill descends makes the tracing outward of the deposits from the rocky knob of anorthosite a difficult matter. Within the orebodies too, some masses of anorthosite persist, which may account for some local irregularities. Fig. 1 is a photomicrograph, taken by reflected light, of a typical specimen of the ore. The dark patches are hematite and the light parts are ilmenite No trace of magnetite was found. Pig. 2 is a photomicrograph of a thin section of the country rock showing the texture of the anorthosite. The mean of four analyses quoted by Robinson1 is: titaninm, 19.26 per cent; iron 45.41 per cent. The ilmenite ore is not sufficiently magnetic to deflect an ordinary compass needle, but the effects of the induced magnetism in the ore by

Jan 1, 1940

By L. S. Panyity

The inception of this paper may be traced directly to the various discussions of another paper by the writer1 wherein certain indefinite beliefs and opinions were emphasized as to the relative importance of total sand porosity and the actual size of the openings between the grains. Since publication of that paper it has been possible to study various methods of sand analyses and results that have been obtained under different conditions and actual operations in the field. The purpose of this paper is to indicate the value of screen analysis, especially in areas where repressuring by means of water-flood, air or gas is being used in the partly depleted fields. Sand samples have been analyzed for porosity, saturation and grain size. They are mainly from the Bradford water-flood area, where a great reliance has been put upon such analyses, and where many data are available, A few sand studies are included from fields other than the water-flood area, in order to indicate the possibilities of screen analysis in any field. Examples of various conditions are given in Figs. 1 to 7, which show the porosity, saturation and grain-size analyses of submitted cores or drill cuttings. The generally accepted methods of delineating such sand studies on cross-section paper, known as "core charts" has been employed; with the exception that a method of representing grain size has been evolved which is believed to be the best adapted for this purpose. It differs from the block diagrams generally used, in the employment of a linear section. Percentage of grain-size is represented by the subdivision of a given distance, where the total length represents the whole sample of rock chunk, while the subdivisions indicate the percentages of grains of the different sizes that will pass through the various sieves, through which the samples of crushed sand are sorted to determine the size and amount of the components that make up the aggregate. Thus, on Fig. 1, under the heading of Grain Size, the first samples are composed of grains of the following sizes: 16 per cent. through 120-mesh sieve; 33 per cent. through 150-mesh; 25 per cent. through 180-mesh; 26 per cent, through 200 mesh; a total of 100 per cent. A minus sign is placed before

Jan 1, 1931

By J. D. Anthony

The Australian continent possesses significant reserves of a wide range of minerals, including bauxite, coal, copper, diamonds, gold, iron ore, lead, manganese, mineral sands, nickel, phosphate, silver, tin, uranium, and zinc. Australia's identified economic resources of many minerals are very large as indicated in Table 1. A sophisticated and highly experienced mineral industry is now an established feature of the Australian economy and Australia is the world's largest exporter of iron ore, alumina, mineral sands and refined lead and amongst the leading suppliers of many other commodities such as coal, lead and zinc ores/concentrates, nickel, refined zinc, tungsten concentrates and bauxite. The industry exports 70% of its production. This is reflected in the value of Australian mineral exports which have grown from about $200m in 1960/61, comprising 10% of total export receipts, to about $1265m or 29% of export income in 1970/71 to around $7061 representing 37% of Australia's total export income in 1980/81. Details of the more significant minerals are as follows: Japan (42.1%) USA (11.3%) ASEAN (6.3%) UK (5.9%) F.R. Germany (3.8%) Republic of Korea (3.4%) New Zealand (2.6%) Also see Table 2. AUSTRALIA'S MINERAL RESOURCES POLICIES Federal and State Governments' Responsibilities Australia has a federal system of government comprising six States, a self-governing Territory and a Federal Government. Under the Australian federal system the Constitution sets down the powers of the Federal Government. All powers not assigned to the Federal Government in the Australian Constitution reside automatically with the States. Certain of these broad powers result in the Federal Government having a significant influence on resources development. For example, in being responsible for economic management, the Federal Government's fiscal and monetary policies have an important effect on industry as well as on State finances. In particular, the taxation regime employed by the Federal Government is of direct importance to decision-makers in the resources industry. The Federal Government is responsible also under the Constitution for external trade matters; and international trade and commodity matters are increasingly important in Australia's international relationships. Foreign investment is another area where the Federal Government has a role to ensure that national interests are protected. This foreign investment power flows from the Federal Government's control of foreign exchange movements into and out of Australia. However, before enlarging on these and others of the Federal Government's powers and policies, it should be emphasized that the State governments, by virtue of their wide powers to regulate matters within their own boundaries, are more directly involved in the day-to-day administration and regulation of mining operations. For instance, the powers of the State governments include the responsibility-for the granting of exploration rights and mining leases, the approval of mining operations and the levying of royalties and other like charges. Administrative arrangements covering the granting of minerals and petroleum exploration and development titles vary from State to State. Before development rights are granted, State governments consider environment protection and rehabilitation aspects of development proposals. The provision of infrastructure within State borders is a matter primarily of State government responsibility. It is usual practice in Australia for State governments to construct and operate infrastructure services such. as railways, ports and electricity generation and transmission. The States may also provide certain public services such as electricity. and water, port and loading facilities, communications, health and education services which form part of the infrastructure of mining operations. In remote areas the mining companies themselves usually are expected to provide much of this infrastructure. However, the Federal Government is primarily responsible in some fields, such as telecommunications and parts of the railways network. State governments carry out preliminary exploration and geological mapping and some are directly involved in the mining of coal for power generation. The Federal Government's responsibilities in addition to economic management, taxation, international relations, foreign capital and investment, include regulation of exports, environmental matters and matters affecting the Aboriginals of the Northern Territory. FEDERAL GOVERNMENT POLICIES The continued sound development of the minerals and energy resources sector is regarded by the Federal Government as being of very great importance. However, the Government does not seek to participate directly in resource developments. It sees its role rather as that of establishing a sound economic and policy climate in which private companies can identify opportunities, seek out customers and marshall the necessary capital for the development of resource projects.

Jan 1, 1982