Search Documents

By Guilherme Corrêa Soares

Deeper understanding about the strain hardening behavior of steels has become necessary due to its importance in industrial processes such as mechanical cold forming, rolling and drawing. In this work, the strain hardening behavior of AISI 304, non-grain oriented electrical (NGO) and dual phase steels was investigated. Tensile tests were performed and the strain hardening behavior of each steel was studied by the Hollomon’s equation. X-ray diffraction measurements and hardness tests were also carried out in order to characterize the specimens. Different work hardening stages were observed in each steel during the deformation process. The results obtained are discussed in terms of the relationship among the instantaneous strain hardening coefficient, hardness and eventual phase transformations. The instantaneous strain hardening coefficient of dual phase and NGO increases after the yield point, rapidly reaching its maximum and then steadily decreases until tensile strength is reached. In AISI 304’s case, the strain hardening coefficient keeps raising to high values in response to a large strain and then rapidly decreases before reaching the tensile strength. In comparison to the other steels, AISI 304 shows higher instantaneous strain hardening coefficient value, which persists even in large strains. This is a consequence of its strain hardening mechanism based on stress-induced martensite transformation.

Aug 16, 2017

By Tiago Salzmann Vilela

No mercado de arames galvanizados destinados a indústria é exigida a uniformidade da camada de zinco sobre o arame. Neste trabalho, foram estudados os efeitos da velocidade de galvanização na uniformidade e espessura da camada de Zinco total, bem como a morfologia das fases de Zn e Ferro-Zinco sobre o substrato metálico. Verificou-se também o efeito do aquecimento após o processo de galvanização, observando o crescimento da camada intermetálica. Finalmente, serão mostradas as principais características de processo obtidas para garantir o atendimento aos ensaios de qualificação, em um estudo de caso de arames galvanizados produzidos em unidade industrial da Gerdau.

Jul 30, 2018

By Wenting Zhu, Liqing Chen, Junjun Cui, Zhenye Chen

In this presentation, a low carbon high strength steel microalloyed with Nb and Ti was processed by thermo-mechanical controlled process (TMCP) containing two stages of controlled rolling. The austenite with various grain sizes was obtained by austenitizing this hot-rolled steel at different temperatures. And the effect of austenite grain size on bainitic transformation was investigated in a dilatometer to reveal microstructural change. The results showed that the microstructure of the hot-rolled steel was mainly composed of granular bainite, lath-like bainite, and martenite/austenite constituents (M-A constituents). With increasing the austenitizing temperature, or increasing the austenite grain size, the microstructure was changed from granular bainite to lath bainite. When the steel was reheated to a lower temperature of 860 ºC, a relatively higher start temperature (Bs) was measured for bainitic transformation. This was mainly caused by the formation of solute-depleted region in the austenite and the promotion of the granular bainitic nucleation. The highest reaction rate occurred at austenitizing temperature of 1000 ºC with fine grain size, while the coarse austenite grain can lead to a sharp increase in the amount of bainite. An analysis was made on the kinetics of bainite transformation which was controlled by the volume diffusion of C atom.

Oct 1, 2019

By Elizaveta Cheremisina

In steelmaking process lime serves as flux. Rapid lime assimilation and slag formation of the desired composition have a significant effect on the refining reactions. It is important to know the rate limiting step of lime dissolution to control and improve the converter process. Kinetics of pure CaO and industrial lime dissolution in model slag has been studied in the range of temperatures 1300 –1600°C. Lime samples were prepared in cylinder form and immersed in the melt for predetermined time. Considering the total mass balance of CaO in the slag and linear dimensions of lime samples, mass transfer coefficients were derived. Diffusion coefficients were calculated under conditions of non-stationary diffusion. The derived activation energy of less than 200 kJ/mol indicates that diffusion is the limiting step in the process of lime-dissolution in slag.

Oct 30, 2017

By Rodrigo Ribeiro de Andrade, Túlio César Nogueira, Ed Juarez Mendes Taiss, Nilton José Lucinda de Oliveira

The objective of this study was to determine the effects of an eventual slab central macro-segregation in microalloyed steels with low Mn content (0.80%) and high Nb content (0.08 to 0.10%) on the kinetics of recrystallization of austenite during its rolling, on its critical temperatures, that is, of non-recrystallization (Tnr), start Ar3 and finish Ar1 of ferrite transformation and its response to a simulated industrial thermomechanical processing. The determination of the austenite recrystallization kinetics was made through isothermal double compression tests using a dilatometer, while the critical temperatures were determined through hot torsion tests in a Gleeble® 3800. It was found that austenite recrystallization kinetics, Ar3 and Ar1 temperatures did not present significant changes for the samples extracted both at ¼ of the thickness and at the core of the plate, indicating that, as expected, the central segregation in this type of steel was not intense to the point of affecting this phenomenon. The Tnr values determined for the samples extracted in the core of the plate were, on average, 30°C lower than those obtained from specimens extracted at ¼ thickness, which suggests that a significant portion of the carbonitrides present in the core of the slab are eutectic and coarse, not having completely dissolved during the reheating of the specimens. This occurred despite the fact that the austenitization temperature adopted in this treatment theoretically leads to the total dissolution of Nb, as seems to have occurred in the case of specimens extracted at ¼ of thickness, where carbonitrides have a finer size.

Oct 1, 2019

By Jorge Madias

Durante la laminación de barras y alambrones para construcción civil; perfiles y ángulos estructurales y barras redondas y hexagonales de aceros de corte libre puede presentarse la apertura de la punta o la cola y el estallido central, con la consiguiente parada y caída de la productividad, y pérdida de rendimiento metálico. En este trabajo se analizan las diversas causas que confluyen para que este problema ocurra. Se analiza la influencia de posibles defectos en las palanquillas, las características del corte de las mismas y otros problemas de calidad. Se revisa el rol del precalentamiento previo a la laminación, la refrigeración de los cilindros, el diseño de pasadas y la respuesta del material en función de su ductilidad. Se presentan diversos casos industriales para ilustrar las diferentes razones detrás del problema de la apertura de punta.

Jul 30, 2018

By Hiroshi Ichikawa

In 2013, Nippon Steel & Sumikin Engineering Co., Ltd. (hereafter referred to as NSENGI), Tenova HYL and Danieli have entered into an agreement to combine ENERGION DR technology into blast furnace technology and/or with syngas technologies. This new alliance will allow the three companies to combine research and development activities with their respective expertise in ENERGIRON DR technology, Blast Furnace technology and Syngas (by-pro gas and coal gasification) technology, with the ultimate objective to develop breakthrough iron making technologies and create such EPC projects. This paper introduces the concepts and the features of our breakthrough technologies of combining of ENERGIRON DR technology, Blast Furnace technology and Syngas technology.

Aug 16, 2017

By Anna Carolina Cerqueira Neves

Synthetic fibers have been gradually replaced by lignocellulosic fibers. Compared to the synthetic fiber, natural fiber showed economic and environmental advantages presenting interfacial characteristics with polymer matrices that favor the impact energy absorption by the composite structure. However, so far little has been reported about the hemp fiber embedded in polymer matrices, such as tensile properties. This study aims to evaluate the resistance in tensile tests of epoxies composites reinforced with different percentages of hemp fiber. Tensile tests were submitted with percentage of 0%, 10%, 20% and 30% incorporated hemp fiber in epoxy matrix. The tensile strength and deformation substantially increased the relative amount of hemp fibers incorporated into the polymeric matrix.

Aug 16, 2017

By Álvaro Lúcio

This paper outlines the DPC process as na economic and environment friendly option for the use of cultivated forest as a source of raw material for metallurgical charcoal.The DPC process was specially developed to bring logistic, environmental, technical, economic and global energy efficiency when compared to termal1 the existing biomass carbonization process. The DPC process utilizes the volatile materials (condensable and non condensable) as a source of the energy required by the carbonization process guarantying its complete combustion. As result the DPC process avoids the burning of termal1 the loaded wood, obtaining a higher charcoal to biomass yield, and avoids the emission to the atmosphere of polluting gases. Gases emitted by the carbonizing wood have na energy termal1e enough to dry the wood soon after its harvesting. By avoiding the storage in the field during na average of 150 days, the resulting economy is quite significant. As a termal1e1 the higher charcoal to biomass yield na termal1e1e economy is obtained through the reduction of the cultivated forest term. This paper emphasizes the economic advantages of the DPC process.

Aug 16, 2017

By Hongshuang Di, Tianyu Zhang, Huiqiang Huang

A CMnSiAl transformation induced plasticity (TRIP) steel was used to study the effect of retained austenite on room-temperature mechanical properties. The steel plates with retained austenite were obtained by hot rolling, cold rolling and subsequent continuous annealing. The starting and finishing temperature of hot rolling are between Ac1 and Ac3. Reduction ratio of cold rolling is 75%. The continuous annealing is carried out at different intercritical temperatures. The relationship between work hardening exponent and retained austenite was discussed. The results show that, the Ac1 and Ac3 were much high because of the alloy elements, and the temperature range between them was wide. Due to the high hot rolling temperature, the grains was hereditarily refined as a result of dynamic recrystallization. Annealing at intercritical temperature of 930 ºC, retained austenite with relatively high stability reached a maximum volume fraction of 25%, a maximum total elongation of 30.2% and a best ultimate tensile strength × total elongation of 20.1 GPa·%. Instantaneous work hardening exponent reflects strengthening mechanisms at different strain stages. The TRIP effect of retained austenite is the main mechanism during deformation. With retained austenite of sufficient amount and high stability, continuous work hardening was observed in the tensile specimen of 930 ºC.

Oct 1, 2019

By Diego Berti Salvaro

The morphology, dimensions and chemical composition of tribolayers strongly depend on the pressures and temperatures acting on the contact. They are formed by reactions between the surfaces in contact with each other as well as with the atmosphere, lubricants and possible contaminants. In this paper the influence of test time (180, 500, 1000 and 2500 h) into the formation and characteristics of tribolayers in pairs DLC-stainless steel tested under refrigerant gas R134a atmosphere without presence of lubricating oil was analyzed. The characterization was performed using scanning electron microscopy, energy dispersive spectroscopy (SEM-EDS) (morphology and chemical composition) and white light interferometry (dimensions). The tribolayers thicknesses ranged from 100 to 500 nm and they were composed by elements originated from mutual transfers between the tribological pairs as well as oxides, being more pronounced on the stainless steel surface. The results show that the tribolayers are chemically stable (maintained the same composition over time) and the thickness remained stable after a thousand hours of testing.

Jul 31, 2018

By Mariana Macedo de Oliveira Lima, Pedro Emílio Gazola, Andrei Locatelli

Boron steel is used in the industry due to its great wear and impact resistance. During the hot rolling production of 15B29 steel flat bars it is a recurrent problem that the bars will present warping while on the cooling bed. Control this phenomenon is an opportunity to have better productivity, preventing metallic losses. Through the observation of the macro and microstructure samples produced with different reheating temperatures and cooling rates, it was found the presence of residual stresses and cracks on warped bars macrostructure. The residual stresses appearance suggest that the material cooling is too fast. Billets temperature on the reheating furnace of 1230°C reduced to 1100°C and the production pace slowed down. Bars temperature when arriving the cooling bed was reduced from higher than 670°C to 625°C. The results obtained made it possible to produce the material with better quality, reducing the warping effect at the cooling bed. The major influence on the materials warping was identified as the cooling rate at the cooling bed and the reheating furnace temperature was adjusted to provide a homogeneous temperature along the bars.

Oct 1, 2019

By Aperam South America

Balanço Energético Global e Utilidades - 2013

Jul 31, 2018

By Mario Andres Albuja Ribadeneira

El presente trabajo pretende encontrar la ruta para incrementar la productividad y reducir el costo de transformación en una acería eléctrica, mediante el uso de la tecnología disponible en el mercado. El método para alcanzar los resultados se enfocan en una drástica reducción de los tiempos de transformador conectado (power-on), los tiempos de transformador apagado (power-off) asi como la reducción en los consumos de las materias primas e insumos para la fabricación de acero por la ruta del horno eléctrico. La experiencia de Adelca arroja resultados que sobrepasan el 100% de productividad y 30% de reducción en el costo de transformación de la palanquilla. Los resultados obtenidos sin duda alguna servirán de una guía probada para quienes buscan un mejor desempeño en el negocio del acero.

Aug 16, 2017

By José Fagundes Junior, Cleudson dos Santos Rego, Bruno Bastos da Silva Murad, Vitor Borlot Borba

Since the startup in 2002, the Hot Strip Mill at ArcelorMittal Tubarão has increased gradually the coil output as the customers demand new and more resistant dimensionally challenging (thinner and/or wider) steel grades. As a critical feature for customer applications, improvements have been carried out aiming a higher thickness performance and reduction of internal losses while still meeting the more restrict tolerances booked by the customers. This paper presents the recent thickness performance evolution since 2017 and the main actions deployed to improve it.

Oct 1, 2019

By Sihai Jiao, Xiaoming Xia, Bo Yan

Checkered plate, which is also known as floor plate, has a raised pattern that provides excellent skid resistance for a wide range of applications, such as flooring, walkways, platforms, stair treads, covers, etc. As one of most common products, carbon steel checkered plate is used in low strength with a large thickness margin for corrosion and costs a lot in corrosion resistance treatment and maintenance. Although austenitic stainless steel checkered plate meets the requirements of general corrosion resistance, it is also hard to provide a highly comprehensive performance for its low yield strength, which mean higher thickness, higher weight, lower stability of structure. Combined the advantages of stainless steel and carbon structural steel, a roll-bonded clad checkered plate with high performance in skid resistance, high strength and corrosion resistant is developed. The metallography shows metallurgically bonded interfaces. Both external and internal bending at room temperature can be done successfully done without any cracks. The yield strength is also significantly improved. Therefore, roll-bonded clad checkered plate is superior in microstructure, strength, ductility and workability. An application case on a pulverized coal injection platform in an iron-making plant, is also introduced to show the way of processing and installation. After two years of installation on the platform, the product still keeps the original appearance. It implies that the developed plate could keep the facilities functions with much less or no maintenance and make them much safer.

Oct 1, 2019

By Davide Onesti

Electrode regulation is the technology at the heart of the AC and DC Electric Arc Furnace. As such, in the last decade it underwent continuous improvement to maximize the EAF performances, in terms of process efficiency, machine utilization and operator safety. Given this background, Danieli Automation’s efforts in the field of electrode regulation have been focused on fast response to scrap cave-in, compensation of supply variations, automatic resonance detection, transformer protection, dynamic regulation of the electrical and chemical set-points, coordination and control of slagging and foaming agents, arc irradiance supervision. An extensive analysis of operator utilization and feedback was also carried out to develop an innovative system HMI. In this field, the choice of the variables shown to the user is the key aspect to allow a prompt process evaluation by the operator, who can refer to a condensed set of useful data. This paper will describe the innovative features and embedded models of the electrode regulation module (Q-REG+) and the supervision HMI, together with the effects of their application on EAF process efficiency and system usability.

Oct 30, 2017

By Giulio Rodrigues Altoé

Environmentally correct composites, made from natural fibers, are among the most investigated and applied today. In this paper, we investigate the mechanical behavior of epoxy matrix composites reinforced with continuous fique fiber, through bending tensile tests. Specimens containing 0, 10, 20 and 30% in volume of fique fiber were aligned along the entire length of a mold to create plates of these composites, those plates were cut following the ASTM standard to obtained bending tests specimens. The test was conducted in a Instron Machine and the fractured specimens were analyzed by SEM, the results showed the increase in the materials tensile properties with the increase of fiber amount.

Aug 16, 2017

By Piezanowski Ludivine

With the aim to reduce the hot metal production cost, ArcelorMittal Gent decided to integrate more ores with finer particle size distribution in the raw material mix for the production of blast furnace sinter. As a consequence of such an increase of finer material in the sinter raw mix, the sinter machine productivity and the quality of the sinter are affected. In order to compensate this impact, modern granulation technology can be employed. Within this context, ArcelorMittal Gent has invested in a vertical intensive mixer. The equipment was placed before the existing drums, with a function of “mixer”, whereas the drums are fully optimised for the nodulizing process. The paper presents the results of the industrial operation during the commissioning phase of the new equipment. Gradually increasing the proportion of fine material in the sinter raw mix has made it possible to compare the performances of the old system using drums for mixing and pelletizing with the new system using an intensive mixer combined with a nodulizing.

Aug 1, 2018

By Dong Maolin

A great amount of high temperature off-gas, whose maximum temperature is up to 2100?, is generated during the smelting process of electric arc furnace (EAF). The dust content, which is mainly iron oxide, of the off-gas is high and worthy of industrial recovery. The heat carried by the high temperature off-gas with dust is about 11% of the total energy input of EAF, and some even is as high as 20%. The high-temperature off-gas not only takes away a lot of heat but also places a huge burden to de-dusting system of EAF. It not only reduces the iron oxide dust recovery ratio, but also causes serious pollution problems. With the development of the iron and steel industry, the proportion of molten iron for EAF gradually increases, and even more than 30% in some cases. The increase of molten iron causes increases in the amount of EAF off-gas and heat waste. As a result the problem of dust removal is worsening [1-2]. How to sufficiently recover the sensible heat of the high temperature off-gas, create conditions for efficient dust removal, thus reduce operating costs of dust removal system and the production costs is a problem which EAF steel making companies must pay attention to.

Oct 30, 2017