Search Documents

By Rolando Campos

Until 1970, the Caletones Smelter of CODELCO-CHILE, División El Teniente, operated under the conventional pyrometallurgical process used by most of copper smelters. The annual copper production varied around 165.000 tons. The failure in the commissioning of the "oxygen smelting" technology in Peirce- Smith converters (1970-1972), forced further introduction of transcendental changes in the Caletones smelter operating scheme. Implemented technological innovations were based on wide studies and research works performed by División El Teniente. This paper presents a summary of technological modifications introduced, their impact on production and energetic performances, and short and medium terms improvement plans.

Jan 1, 1993

By Zhenfeng Zhou, Qingguo Xue, Jingsong Wang, Guang Wang, Yuanyuan Zhang

The oxygen blast furnace is a new technology for ironmaking, where the oxygen and CO2-stripped blast furnace top gas are blown into the blast furnace replacing the conventional hot air. The oxygen blast furnace could reduce the consumption of coke and emission of carbon dioxide. In this chapter, a three-dimensional numerical model was developed to simulate the lance-blowpipetuyere-raceway region of a blast furnace, and the flow and combustion behaviors of coal particles were investigated based on an oxygen blast furnace. Compared with the traditional blast furnace, the combustion characteristics in the raceway of the oxygen blast furnace were different. In addition to the combustion of coal and coke, the combustion of large amounts of reducing gas was included. The coal combustion of different oxygen content (70, 80, 90, 100%) were investigated. The simulation results indicated that the coal burnout was only 21.64% at an oxygen content of 70%, a decrease of 51.52%, compared with a traditional blast furnace. The coal burnout was increased with the increase of oxygen content. When the oxygen content is 100%, the coal burnout was 90.38%, an increase of 17.22%.

Mar 1, 2017

By Maria de Campos

The pre-reduction behaviour of chromite particles in methane-argon and methane-hydrogen gas mixtures was investigated between 1050°C and 1250°C. Loose bed of chromite particles were reacted in a vertical tube furnace under a pre-set gas mixture predetermined time intervals. Metallization results were obtained for the Cr and Fe components by chemically analyzing the reaction products. SEM-EDAX techniques and X-ray diffraction were employed to elucidate the reduction mechanism. It was found that higher reduction kinetics and higher Cr:Fe ratios in the metal phase would be achieved when hydrocarbon gas was used in comparison to classical carbothermic reduction at a given temperature. The reduction rate was generally bulk gas mass transfer controlled to the reaction site for initial stages which then was followed by ionic diffusion rate control. It is proposed that methane did not partake directly in the reduction but cracked, presenting the reaction site with hydrogen gas and atomic carbon, which was able to immediately react at the immediate area of reduction regeneration CO and H2 and thus maintaining a low partial pressure of oxygen at the reaction site.

Jan 1, 2006

By Payal Bakshi, Sangeeta Tiwari, Mohini Saxena, Anusha Sharma

"Recycling and reuse is perhaps the most favorable and beneficial way to solve the problem of industrial waste disposal. However, the use of industrial wastes like fly ash, tailings etc is in practice for brick manufacturing, land filling, embankments filling etc. These existing practices do not add enough value to the wastes. Moreover, some wastes may have very good potential to be incorporated in valuable products like paints. This study reveals about the value addition of industrial wastes like fly ash, copper tailing and blue dust as an extender in paints. Comparative properties and characteristics of these three wastes for application in paints are discussed. Fly ash, copper tailing and blue dust were characterized for physical, chemical and mineralogical properties and used in different paint formulation based on their potential to the particular application. Fly ash has been found very useful in enamel, primers and flat paints while copper tailing was found suitable in oil based paint formulations. The performance of fly ash and copper tailing paints were evaluated by comparing with those of conventional whiting extender. Blue dust was compared with conventional iron oxide for use in priming coats. The extender properties of these new material and paints prepared out of blue dust, fly ash, copper tailing, were found better than the existing related materials.IntroductionIndustrial development and environmental reforms should run parallel to benefit each other. This is the best policy, which must be adopted by industries for the sustainability of the current modern life. The high degree of industrialization and urbanization adds scads of waste resulting problem of pollution and challenges of their safe disposal. The nature of waste depends on the process that produces waste as its by-product. Therefore, policies/plans are prepared by keeping the view of possible potential hazards. Among the different wastes some are generated in the industries, which have great importance in the country’s economy, like fly ash waste from thermal power industry and mining waste. In India the total contribution of thermal power in the total electricity generation is more than 70% and it produces about 123 million ton of the fly ash annually [1]. On the other hand mining plus extraction of ferrous and nonferrous metals also produce waste in million tonnes of categories [2]. Since the generation of this waste is very high they cover large land area for their disposal and dumping [3]. The storage of this waste in the dumping sites for long time duration may cause problem of land, surface water, ground water and fertile soil contamination [4]. As far as Indian fly ash is concerned it does not contain toxic element over the limits of hazardous waste [5]. However, in general most of the metals deposits are found in the form of pyrite based ores. Mining wastes contain toxic elements e.g. heavy metals in varying amount, which get mobilized when pyrite get oxidized to sulphate producing sulphuric acid [6,7]. These ores contain very less amount of targeted metals in themselves thus they require extensive preprocesses for concentration of the metals [8]."

Jan 1, 2008

By Cameron Hams

Noranda's Process Reactor and Codelco's Teniente Converter are physically similar vessels, which leads to the commonly held misconception that the two processes are the .same. However, notable differences in chemistry, operating philosophy, and construction make them quite dissimilar. This paper compares and contrasts the Noranda Reactor and the Teniente Converter, and attempts to explain some of the apparent differences in behaviour and performance. The results of a worldwide survey of most operating Noranda Reactors and Teniente Converters, along with those processes that have ceased operation or are planning to be started-up in the future, are presented.

Jan 1, 1999

By S. G. Galbraith

We have used the principles of supramolecular chemistry to develop reagents to transport metal salts. These reagents have separated charged "compartments" which recognize a metal cation and its attendant anion(s). They are easy to manufacture as they are structurally related to the commercial hydroxy-oxime extractants for copper. Efficient protocols for loading and stripping of these extractants depend on the novel feature that they bind the metal salt in a zwitterionic form of the ligand. Transfer of the phenolic protons to the pendant amines generates the charged "compartments" to accommodate the metal cation and its attendant anion(s). This paper focuses on how these types of reagent can be used to recover base metals from sulfate and chloride media in flowsheets in which solvent extraction effects separation and concentration operations, interfacing between conventional leach and electrowin/reduction processes. Work on the development of reagents that have high selectivity for metal chloride/sulfate transport, convenient stripping protocols and appropriate hydrolytic stability will be described.

Jan 1, 2003

By Lee Fergusson

"The primary features of ViroMine™ Technology are introduced and applications of ViroMine™ Technology to mine site remediation and the treatment of a variety of intractable waste-streams, including a technical discussion of acid neutralizing capacity, metals binding capacity and longterm stability of results. Outcomes from four applications at high-profile international mine sites are presented: 1) the superfund site at the Gilt Edge Mine, South Dakota, USA (four years of data on the treatment of acidity, TDS and metals such as Al, Co, Fe, Mn and Zn); 2) one of Australia’s most polluted sites at King River Delta in Tasmania (treatment of TAA and TPA, and metal and metalloid contaminants such as As, Cr and Hg); 3) The Aljustrel “Aqua Forte” mine site in Portugal (high acidity, metal and metalloid contaminants such as Al, As, Cu and Zn) and 4) the Ulsan Iron Ore Mine at Ulsan, South Korea (treatment of metal and metalloid contaminants such as As, Cd and Ni).IntroductionThe commercialisation of ViroMine™ Technology has resolved some of the most intractable pollution issues associated with historic mining ventures on a global scale and has facilitated the neutralisation of Acid Rock Drainage (ARD), remediation of acidic and metal contaminated impoundments (including tailings dams) and promoted revegetation on tailings deposits and waste rock dumps. ViroMine™ Technology also enables current mining ventures to manage effluent simply and efficiently to meet increasingly stringent environmental standards and is enabling the mining sector to reconceptualise the management of mine spoil. The abilities of ViroMine™ reagents to neutralise the actual and potential acidity of sulphidic mine spoil coupled with the ability to bind metal and metalloid contaminants into non-bio-available forms are the key features delivering environmental and economic benefits to the mining sector and the broader community. Results from four projects utilising ViroMine™ Technology are presented to highlight the suitability of ViroMine™ Technology to treat all forms sulphidic mining wastes. 37"

Jan 1, 2008

By Zhenfeng Zhou, Qingguo Xue, Jingsong Wang, Yingli Liu, Yuanyuan Zhang, Hailong Huo

Coal burnout strongly depends on the residence time and dispersion of coal particles in the raceway region of a blast furnace. The residence time and dispersion of coal particles are directly related to the lance arrangement. In this work, a three dimensional model was developed to simulate the lance-blowpipe-tuyère-raceway region of a blast furnace. Double lance and eccentric configurations were considered. For the double lance, the double-lance and eccentric double-lance were considered. For the eccentric double lance, the effect of intersection angle of the two lances was investigated.

Mar 1, 2017

Four slag types covering the range of Fe-Ca-Si-O compositions and two iron blast furnace slags were melted at 1300 °C and doped with 1% of arsenic, antimony, cadmium, zinc and chromium. The melts were either slow cooled or quenched and the solidified slags were leached according to TCLP procedures. The morphology of the solidified slags was characterised using XRD, optical and electron microprobe techniques. Theoretical considerations showed that the capacity of the molten slag to hold the above toxic elements depended upon slag basicity and this was confirmed in practice. The experiments showed that the leaching of the toxic elements was a function of surface area and the phases present, both of which were affected by the mode of cooling. Iron silicate slags produced in nonferrous smelting operations and blast furnace slag from ferrous smelting operations both show promise of being suitable media for immobilising low levels of toxic elements and complying with current regulatory requirements.

Jan 1, 1994

By A. H. Rhoades

The modern polarizing microscope with such accessories as cameras, infrared devices, reflectance and/or transmission photometers, indention hardness, and heating stage is used to characterize coal, coke, and other carbon forms. It allows characterization of coke by-products, such as tars and pitches and their insoluble residues. A useful product of the microscopic approach is the coal petrographic analysis which permits the prediction of coke strength carbonization pressure and volume change. Carbonization tests are expensive, time-consuming and require large amounts of coal. Tests on the coke show it to be strong or weak but give no indication of why. Petrographic analysis requires grams of coal and yields data that indicates why the coal produces coke of a given quality. Small samples from drill cores are sufficient for petrographic analysis. These data are also used to optimize blends for coke production. When coke-plant problems occur, ~he microscope can be used to check the coal blend proportions, as well as for weathered coal. Microscopy is useful in spore correlation work which may be a prerequisite to sound coal reserve estimates. Dispersed vitrinoid reflectance studies are used to determine the degree of organic metamorphism which serves to establish oil and gas deadlines. Tars and pitches are examined microscopically for the amount of normal solids as well as the size of undesirable carry-over solids resulting from pollution abatement practices in coke works. The microscope is also used to study coals for gasification and liquefaction.

Jan 1, 1981

By Larry M. Southwick

There is much ongoing work in research and development of new processes for the recovery and recycling of met.a.ls and other materials from various waste and scrap streams. Commercialization of such new technologies requires the bringing together and successful execution of a considerable effort involving a variety of activities. These include process conceptualization, research and development, detailed design and construction, and then plant startup and operation. Processes evolve through all of these steps by engineering due diligence, making objective and critical analyses of results, and troubleshooting processing steps to, hopefully, arrive at a sequence that has the best chance to succeed operationally and economically. After a summary review of the above steps, several processes will be described in more detail that provide mostly successful examples of the above procedures. Finally, some observations will be made on areas that will become critical in the near future to the success of new processes for wastes and residues.

Jan 1, 2000

By Jeffrey W. Braithwaite

The laboratory characterization of the oxidation of chalcopyrite under conditions of deep solution mining is presented in this paper. A salient feature of this system is the pH buffering effect resulting from simultaneous acid producing and acid consuming oxidation reactions. The solution chemistry and related sulfur partitioning of the oxidation reactions are detailed. The contribution of temperature, acid concentration, oxygen pressure, particle size, and solution additions to the kinetics of copper extraction are presented. A mixed kinetic model was used to describe the kinetics of oxidation.

Jan 1, 1976

By T. Lezhava

A new reactor model with rotating cathodes has been developed where various forms (dendrite, spongy) of metal depositions and their uninterrupted removal are accomplished by the realization of high current densities and low energy consumption. At the same time in contrast with the existing methods a high quality metal powder may be obtained from concentrated electrolytes without any specific organic or inorganic additives, which allows raising the intensity of the process. The reactor can be used for electrowinning of metals with low adhesive capacity (Pb, Ag, Cu, Zn, Ni, Co, etc.) and the powders. The obtained products may be utilized in general metallurgy as well as in powder metallurgy.

Jan 1, 2006

By B. R. Adams

This paper discusses the use of a reacting CFD model to determine chalcopyrite kinetics in a drop tube furnace and to predict the reaction of a chalcopyrite concentrate in the reaction shaft of an industrial smelter. Reacting CFD codes can be applied to determine the consequences of the interaction of gas with particles and therefore improve the ability to derive kinetic parameters that take into account the temperature and oxidation histories that different particles will see. This paper describes the application of such a model to derive improved kinetic parameters for the pyrolysis and oxidation of chalcopyrite. The reaction shaft model includes the effects of turbulent fluid mechanics, entrained flow mixing, turbulent particle dispersion, heterogeneous particle reactions, radiative and convective heat transfer, and' surface and bath deposition rates. Particle reaction and composition characteristics are predicted as a function of particle trajectory and deposition and are used to aid in evaluating shaft performance.

Jan 1, 1999

By P. S. Seryogin

R & D works supported by industrial-scale tests, which were carried out by joint efforts of the OAO Gipronickel Institute and MMC ?Kola? engineers, have accomplished with the production of 90?95% metallized nickel powder in tube furnaces (NPTF), with its ?active fraction? (AF) to be further used for decopperization of nickel electrolyte by cementation. Consistently positive results obtained in the course of the lab and industrial experiments have allowed the Severonickel Combine management to effectively replace all activated nickel powder (ANP), which was then employed for cementation, with the AF, having activity over 80%, and eventually shut down the entire operation of gaseous reduction. Ever since the developed technology has been implemented, its annual economic effect exceeds 2 ml. dollars.

Jan 1, 2006

By Shunsuke Yagi

A surface alloying technique was investigated using alternating pulsed electrolysis in an aqueous solution containing a single metal component for the formation of an Fe-Cr layer on an iron substrate. In the process, the iron substrate was dissolved during each anodic polarization of the pulsed electrolysis, providing iron ions in the vicinity of the substrate, while the Fe-Cr alloy was electrodeposited during subsequent cathodic polarizations. A bright, flat, and crack-free Fe-Cr layer with a composition gradient was obtained using a solution containing a trivalent chromium component and a complex forming agent together with some supporting or buffering salts.

Jan 1, 2006

By A. Rohkohl, R. Piillenberg

The QSL plant at "BERZELIUS" Stolberg GmbH in Stolberg, Germany was commissioned in 1990, introducing a new era of lead smelting in the more than 150-year-old history of the lead smelter. The lead smelter in Stolberg has changed its appearance several times during its existence. Therefore, at many locations on the site, old and obsolete buildings and equipment parts can still be seen. They are often located side by side with new modern constructions like the QSL-plant and the mercury removal plant, and reflect the specific contrast between tradition and modern technology. After a brief description of the development of the smelter and its decision to implement the current novel plant, the most recent operating results are reported. Following some modifications to the process and equipment, which had become necessary along with the implementation of the new technology, the plant is in operation today at approximately 30% above its design capacity. These achieved production levels are not restricted by the QSL-reactor but by precedent and subsequent available equipment. The QSL-plant entirely complies with the demands of modern, energy-saving, ecologically compatible lead production technology. Stringent environmental standards are maintained on a continuing basis. The demonstrated viability and flexibility of the overall process permits the operation to adapt quickly to the prevailing economical situation worldwide.

Jan 1, 2000

By V. Vergara

Four copper composites were obtained by mechanical alloying, using as dispersed phases of four carbide powders; they were: boron carbide, chromium carbide, silicon carbide and zirconium carbide. The purpose of this work was to study some characteristics of these compounds and their feasibility for use as materials for electrical equipment. Raw materials used were copper powder finer than 150 mesh, and 2-4 vol % of powder carbides finer than 325 mesh. The alloying process was carried out using both a Spex 800-D mill with tungsten jars and balls and a hardened stainless steel jar and balls, the purpose of which was to measure the degree of contamination induced by the milling media. The changes in particle size, morphology and microstructure of copper alloys were studied with SEM and TEM for each alloyed powder. The degree of saturation of copper by the carbides was measured by X-ray diffraction. Sound samples were obtained by hot isostatic pressing at 1073°K. The best characteristics were obtained for the compound copper-chromium carbide, based on their hardness, tensile strength and electrical conductivity values. The other alloys failed due to their excessive brittleness after hot pressing.

Jan 1, 1999

By R. G. Haire

Studies of the f-elements under pressure provide important insights into their solid state chemistry and physics. From such studies, of the elements and their alloys, it has been established that the normally localized f- electrons of several of these elements can become, involved in bonding under pressure. The electronic behavior of f-element compounds under pressure tend to be more difficult to interpret, due to the variety and the nature of electronic orbitals that are present. The 4f-elements and some 60% of the 5f-elements have been studied under The systematic comparisons that have been established for these materials are discussed.

Jan 1, 1992

By Antrekowitsch Jürgen

The recycling of residues from metal producing by-products has become a main field of interest in metallurgical investigations. Forced by a stricter environmental legislation and the resulting increase of landfilling costs, combined with the aim to recover as many valuable metals as possible, a lot of different processes have been developed in the last two decades. Because of the high yearly tonnage residues from the iron and steel industry like slags, dusts and sludges have moved in the center of interest. Dusts from the steel mill, containing heavy metal oxides and halides did not play a considerable role as secondary raw materials for a long time. They even contain a huge amount of leachable elements and compounds which cause noticeable problems in case of a dumping. Nevertheless, the implementation of a new landfilling regulation, including a prohibition of aboveground dumping without inertisation, caused a rising interest concerning recycling technologies for such residues. In addition, the zinc content of these dusts became higher and higher and began to play the most important role for the economy of dust recycling.

Jan 1, 2006