Search Documents

By H. N. Maleki

Extensive measurements and underground observations in three Western U. S. coal mines are integrated in this paper to determine in-situ pillar load-deformation characteristics for narrow (30 it wide, 80 ft long) pillars in two-entry gate road systems. In spite of similarities in the regional geology, coal pillar laboratory mechanical properties and gate pillar geometries, the pillar peak strength, post-failure behavior, and failure mechanism were shown to be significantly different. Pillar peak strength was shown to be dependent on depth at one site, approaching burst-prone stress levels of 4000 psi. At another site, the pillar peak strength was lower because of lower confinement; this was related to the higher frequency of cleats and the lower friction- al properties of the roof/floor and coal contact. Two failure mechanisms were identified - one in the pillar, and the other in the mine floor. The roof stability was good at all three sites because of the thick-bedded nature of the roof strata and limited total gate span in a two-entry system. Existing pillar design techniques were shown to be inadequate for design, requiring adjustments for depth of cover, cleat frequency, and roof /floor frictional properties.

Jan 1, 1988

Previously, a variety of risk rating systems were used on different mines. However, these were mostly site specific and geology based systems. The purpose of developing a uniform rating system, to be used on all Anglo Coal open cast mines, is to provide an unbiased, standard and quantifiable assessment of the risk from highwall and lowwall failures. This takes into account relative differences in the importance of hazards, as experienced on each mine as a result of different combinations of geotechnical factors and mining conditions. The system is based on critical geotechnical and other parameters that have been identified by mining personnel and rock engineers. The primary advantage of this risk rating system is that all open cast mines in Anglo Coal use an almost identical system, which enables the user to compare their risk to the risk at neighbouring mines and/or other open cast mines. The system can be adjusted to meet local, mine specific requirements. The implementation of this new system (a computer program that automatically calculates the risk) has been made as practical and easy to use as possible. Therefore, this tool can be used by personnel from other mining disciplines not directly related to rock engineering.

Jan 1, 2004

By K. Hanna

This manuscript describes an extensive ground control study at the Inland Steel No. 2 Mine near McLeansboro, IL, conducted by the U.S. Department of the Interior's Bureau of Mines (USEM) in cooperation with Inland Steel Coal Co. The mine experiences severe ground control problem primarily due to high horizontal stress, particularly at entry intersections. Mine experience has shown that reorienting mine entries, modifying the bolting pattern, and altering the mining sequence are effective in reducing the severity of roof falls and out-of-seam dilution. However, the frequency of roof falls has not been significantly reduced. This research project was designed to provide a thorough explanation of the intersection failure mechanism through combined analyses of company in-mine experience and Bureau field measurements. Stresses and deformations were monitored in a four-way intersection during all stages of development and were related to site observations and theoretical analyses. The results of the combined analyses indicate that high horizontal stress is the predominant factor contributing to intersection roof falls in the Inland Steel No. 2 Mine. The horizontal stress induces shear zones to form along the outby 1 ribs, causing the immediate roof layer to detach 1 and behave as a cantilever beam oriented diagonally across the intersection and parallel to i the maximum horizontal principal stress. As the shear zone progresses upward, roof layers successively detach and fail, forming a dome-type roof fall.

Jan 1, 1986

By Jay Keng

During the construction of shaft on the fractured and weak rock strata, the stability of construction plays an important role. This study includes earth stress estimation, support method, and stability analysis. Stresses on the site of three shafts include structural residual stresses, earth pressures, and hydrostatic pressures were determined. The basic method of estimating the support strength is dependent upon the' size of the plastic ring after rock excavation. During the construction of the shaft, geotechnical measurements, physical properties of the rock, and the change after excavation have to be evaluated again. Geology and construction methods need further consideration.

Jan 1, 1988

By André Vervoort

To learn more about the fundamental roof behaviour in South African coal mines, accurate underground measurements of roof deflection were conducted in bord and pillar panels during development and pillar extraction. To conduct these measurements a survey levelling technique was adapted. The overall system reading accuracy was established as being within 0,4 mm on a 15 m sighting distance. The underground sites were modelled and, for a roadway development, similar symmetrical curvatures were calculated by a linear elastic model, as were measured underground. In a pillar extraction panel, a significant amount of bed separation was measured and the roof underwent an a-symmetric movement due to the close presence of the mined out area at one side of the roadway.

Jan 1, 1992

By David L. Kuck

This paper describes a system for providing structural, support in underground mines, employing water ice for pillars. packwalls and brattices. It consists of a refrigeration brine chiller, brine circulation system, and disposable plastic containers. The system provides for the timely freezing of uniform ice pillars, and for ice maintainance and/or melting on demand. Unique, useful ice properties include: expansion upon freezing, resilience to dynamic loads, and plasticity. Ice will not dilute or contaminate coal or ore. Economic advantages include: 1) lower labor and material costs (water can be piped to the ice pillar site through mine-water, spray-water, or drill-water lines); 2) replacement or supplementation of timber. concrete or other roof support equipment; and 3) potential use of ice brattices as ventillation control; and 4) conversion of ice bratices to ice pillars upon retreat. See Figure . A safety advantage for personnel and equipment is that ice pillars can be placed in hazardous sites, by remote control, if neccessary, without human entry. All filling, freezing and melting operations can be controlled from a safe distance.

Jan 1, 1987

By Axel Preusse

Due to a political decision, German hard coal mining will come to an end in the year 2018. By then, there will have been more than 150 years of industrial grade mining activities. Located in the western part of Germany is one of the most densely populated areas of Europe. Multiple coal seams have embossed the earth?s surface up to 20 meters (21.87 yards), as mining has subsided. The aftercare of hard coal mining will consist of three tasks: groundwater management, polder management, and groundwater treatment. The Ewigkeitslasten (cost in perpetuity) at the current groundwater level has been determined in the past. The actual cash value is calculated to be about 12.4 billion euros (approximately 16.5 billion dollars). The cost of groundwater management is directly related to the groundwater level. Rising groundwater levels will reduce the cost of pumping water. Known effects of rising groundwater are uplift of the surface, emission of methane gas at the surface, higher risk of cave-ins, and contamination of drinking water horizons. Each of those processes produces cost in order to prevent negative consequences (e.g., uncontrolled methane emissions) or to handle reparations (e.g., damages caused by surface uplifts). In the long run, it is the goal to minimize the Ewigkeitslast. As a first step, all cost-generating processes are specified, and a cost type based characterization is performed. The objective of this case study is to identify key parameters to determine the quality of a cost-generating process (proportional cost, fixed amount cost). Afterwards, it is intended to specify the quantitative impacts of each parameter and to set up an optimization model to minimize the overall cost. The quantitatively specified parameters will form the base out of which the optimization model is created.

Jan 1, 2013

By Kevin W. Harris

Multiple-seam coal mining is a major issue in underground coal mining that adds additional complexity to the practice of ground control. As reserve exploitation is driven by economics, it is now difficult to mine coal without the existence of previous workings above and/or below the active seam; this is particularly true in the Appalachian coalfields. The frequency in which problematic multiple-seam interactions are now encountered has resulted in significant research regarding the underlying mechanisms of the problems and methods of mitigation. In the last few decades, a great deal has been learned about these interactions and the ability to minimize problems associated with these hazards has greatly advanced, resulting in better economics and improved safety. Minimizing the adverse effects of stress interactions often requires a thorough understanding of site-specific geotechnical parameters and previous mining geometry. This is especially evident in bump-prone ground, where pillar behavior is highly dependent on local conditions. This paper presents a case study in a deep cover, Central Appalachian coal mine where three bump events occurred. Initially, empirical design software was used in an effort to analyze the situation and prevent further instability. The empirical study proved ineffective. A detailed investigation of the bump events using the boundary element software LaModel 3.0 was then performed. This study resulted in a site-specific calibration standard that will be applied in numerical pillar design for the remaining reserve.

Jan 1, 2014

By Dennis Dolinar

In general, the direction of the maximum horizontal stress in the eastern United States is fairly well defined. However, the variation of the magnitudes of the horizontal stresses is not very well understood. Because the horizontal stresses cause severe ground control problems in underground coal and limestone mines throughout the eastern United States a more complete understanding of how the magnitudes vary would be useful for developing mine design strategies to combat horizontal stress related ground control problems. Therefore, in this National Institute for Occupational Safety and Health (NIOSH) study, the variation of the magnitude of the horizon stresses in sedimentary deposits in the eastern and Midwestern United States are examined with respect to two factors, the elastic modulus of the rock and the site depth. Stress measurements from thirty-seven sites are used in the evaluation. Examining the applied excess strains indicates that the eastern United States can be, separated into high and low strain zones. For most of the eastern United States the maximum applied excess or tectonic strain ranges from only 300 to 550 micro strains. However, there is one area, a portion of the Beckley seam in the central Appalachian region where the strains are significantly higher than the other regions. In this higher strain zone, the maximum applied tectonic strains range from 700 to 1,000 micro strains. Regression models for each zone based on the elastic modulus can explain between 83 to 85% of the variation of the maximum horizontal stress. Because one region, the northern Appalachian district, has strains that are about 20% higher than the other regions in the low strain zone, multiple strain models based on geographic regions were developed for the low strain zone that can explain 87 to 91% of the maximum horizontal stress variation with the elastic modulus. Depth was found not to be a significant causal factor in any increase in the horizontal stress even though the site depths ranged from 275 to 2,500 ft. Beyond a theoretical increase, based on Poisson's effect and gravity, no other increase in the horizontal stress with depth can be justified with this data. The most significant factor controlling the variation of the maximum horizontal stress is the elastic modulus of the rock, not the overburden depth.

Jan 1, 2003

By Stephen C. Tadolini, John P. McDonnell

"High-strength cable bolts have been used for ground support in underground coal mines for many years. Cable bolts are routinely used as secondary ground support in numerous longwall gateroad support applications, areas that possibly experience the most severe conditions in current underground coal mining. Additionally, when mining ground conditions deteriorate, engineers oftentimes recommend cable supports as a principal solution because of the established credibility for successful ground control. Nevertheless, there is still a reluctance to utilize non-tensioned cable supports as an effective primary roof support alternative.This paper provides historical and recently documented examples of non-tensioned cable supports utilized as an effective primary ground support method in a western U.S. underground coal mine, and it will continue the technical discussion between the differences of various degrees of tension in cable supports with respect to ground behavior and reactions.INTRODUCTIONResin-grouted cable supports are widely used to support difficult ground conditions throughout the world. Through the use of innovative applications and configurations they have proven to be a major paradigm shift in roof support and ground control technology in the U.S. (Tadolini and Koch, 1993; McDonnell et al., 1995; Tadolini and Gallagher, 1994; Tadolini and Trackemas, 1994)Today, the basic cable bolt support consists of a high-strength steel cable installed in bore holes that range in diameter from 25 to 50 mm (1 to 2 in) depending on the strand size and drilling equipment. Cables are offered in both bright and galvanized, for corrosion protection, and range in capacity from about 30 to 60 tons. An example of a resin-grouted cable bolt and the key components is shown in Figure 1. The steel cables are flexible and the support length is not limited by the height of the opening. Lengths of up to 10 m (32 ft) have been supported with high pattern densities when standing supports were not operationally feasible. The most common lengths are 3 to 5 m (10 to 16 ft). An important physical characteristic is that PC-strand has an ASTM minimum elongation requirement of 4%. For comparison purposes, the ASTM 432-08 Standard Specifications for Roof and Rock Bolts and Accessories specifies elongation requirements for traditional roof bolts are a minimum of 12% for grade 40, 9% for grade 60, and 8% for grade 75 materials, respectively. Traditional roof bolts can stretch and elongate twice the length that cable bolts can, which makes design considerations challenging."

Jan 1, 2010

By Anthony Iannacchionc, Jessica Benner, Harold Miller, Megan Witkowski

"Longwall bituminous coal mining has been practiced in Pennsylvania since the 1970""s. Hundreds of longwall panels have been mined during the last 40 years but only 24 have actually undermined Pennsylvania's Interstate Highway System. The impact to interstate highways are summarized in this paper and the factors that influence the magnitude of these impacts are examined.INTRODUCTIONOver the last 30 years, interstate highways in Pennsylvania have been undermined by portions of 21 bituminous coal mine longwall panels. From 2003 to 2008, three of the panel were extracted by the Emerald Mine and six by the Cumberland Mine both in Greene County and both owned by Alpha Resources. Previous assessments of longwall mining under Pennsylvania’s interstates have identified impacts to the highways but no danger to public safety. In general the magnitude and extent of impacts during the recent undermining of Interstate 79 or 179 appears to be similar as those identified in previous studies. The nine longwall panels are among some of the widest in the U.S. They are supercritical in character with overburdens ranging from greater than 152 m (500 ft) to less than 305 m (1,000 ft).The Pennsylvania Department of Environmental Protection (PA DEP) requested that the University of Pittsburgh summarize observations collected by their staff during the recent undermining of 179. Observations and photographs of impacts to the highway were made by PA DEP staff and entered into reports prepared by California District Mining Office (COMO) staff and statements written into the Bituminous Underground Mining Information System (BUMIS) database. In addition to the observations by the PA DEP, the Pennsylvania Department of Transportation (PennDOT) conducted a series of detailed land surveys along portions of the highway undermined from 2003 to 2008. To characterize the subsidence basin fanned by longwall mining. PennDOT information has been analyzed by another research group within the university (Guticrre7, et al., 20 I 0)."

Jan 1, 2010

By Steve Signer

The San Juan Mine and the National Institute for Occupational Safety and Health conducted a study to measure how development mining effected bolt loads. Twelve fully grouted, instrumented roof bolts were installed at two three-way intersections as part of the standard bolting pattern. Newly developed miniature data acquisition systems (MIDAS) were used to measure bolt load changes during initial face advance and cross-cut breakthrough. The effects of cut placement and depth on roof bolt loads were studied This test showed how bolt loads increased at five positions along the bolt length during initial mining. Both entry advance and cross-cut breakthrough produced a similar percentage of increase in bolt loads. Geologic differences between the test sites were probably responsible for the differences in amounts of bolt loading. The test site with more top coal and a higher rock quality designation (RQD) had lower bolt loads.

Jan 1, 2004

By Megan N. Witkowski

The purpose of this study is to investigate the susceptibility characteristics of domestic and agricultural water supplies that may be vulnerable to diminution or total loss of supply when active longwall mining is in the vicinity of the potable aquifer systems of southwestern Pennsylvania. The study focuses on water supplies in Greene and Washington Counties with reported losses or reductions in supply that were attributed to the seven active longwall mines in operation between 2003 and 2008. The undermined water supplies represent a variety of hydrogeological settings and mining conditions prevalent in the southwestern Pennsylvania longwall coalfield. The susceptibility characteristics investigated include hydrogeological setting, proximal location to mining, and climatic conditions at the time of impact. The investigation considers the relationship between geological and mining characteristics. Geological characteristics include overburden composition and geomorphology of the surface; mining characteristics include mining method, depth, and extraction thickness. It was determined from the study that the average overburden thickness at each mine site is indicative of hydrological changes to potable aquifer systems, with the overall impact frequency at each site decreasing as depth to mining increases. However, depth to mining was not the governing factor when hydrological responses were determined on a case-by-case basis. To fully analyze and hopefully predict potential impacts by longwall mine subsidence, it is necessary to consider additional factors including topography, distance to mining, mining method, and climatic conditions at time of undermining. The investigation serves the purpose of enhancing our understanding of hydrogeological responses to longwall mining and will aid in predicting potential impacts to southwestern Pennsylvania?s wells and springs in proximity to future mining.

Jan 1, 2011

By Kenneth L. Johnson

The effects of underground longwall coal mining on flow in perennial streams within the Pittsburgh seam basin were evaluated. Four streams above four different longwall mines were studied. Overburden depths at the study sites ranged from 500 to 600 feet. At all four locations, premining streamfow measurements were made to establish baseline flow conditions. Measurements were then repeated at each location after the longwall face passed beneath the stream. At one location, in which the longwall panel axis was roughly parallel to the stream, the streamflow was monitored as the longwall face advanced. Measurements at this location showed that temporary flow reduction occurred as the face advanced underneath; however, after the tensile portion of the traveling subsidence profile passed, this effect was lessened. At two of the sites in which the stream was roughly perpendicular to the panel axis, postmining streamfow increased across the panel and decreased over the development headings, such that the net lateral change in streamflow across the fully subsided panel and associated development headings was small compared to the measured flow.

Jan 1, 1997

By Bruce Hebblewhite

An ACARP-funded industry research project in Australia recently investigated the problem of premature rock bolt failures in underground coal mines. The project carried out limited sampling from 9 different collieries in NSW and Queensland, followed by a more comprehensive, controlled sampling from one colliery. Over 50 broken bolts were collected and subjected to metallurgical analysis at UNSW to determine both the steel composition and to analyse the fracture surfaces. Prior to this study, there had been anecdotal evidence of similar bolt failures from a number of sites within the industry. The sampling and analysis conducted by this project - whilst being below a statistically representative sample of the entire industry bolt population - highlighted the fact that bolt failures were continuing to occur at a number of sites, in both older and recently installed bolts. The failures were almost entirely attributable to stress corrosion cracking (SCC). It appears that a combination of factors - including steel composition, bolt manufacturing process, loading environment, geological and hydrological environment, bacterial corrosion - can all contribute to this problem. There is no simple solution, however, as with similar research findings from the UK, it appears that steels with higher values of fracture toughness, or Charpy Index, are less susceptible to SCC. Testing to date has been limited to bolt failures below the resin encapsulation horizon. A real concern is the potential extent of the problem at higher horizons, within the encapsulation. These may require some form of non-destructive testing (NDT) for detection. Initial trials in Australia of the ultrasonic device developed by DMT in Germany have proved encouraging. Further testing using this device is anticipated in future research. This paper describes the outcomes of the project, completed in 2002.

Jan 1, 2003

By David Gearhart, Peter Zhang, Gabriel Esterhuizen

"Researchers from the National Institute for Safety and Health (NIOSH) installed instruments in the track entry and in the pillars of a northern West Virginia longwall coal mine between two planned panels for the purpose of monitoring the behavior of the ground. The instruments included four cable bolt load cells to measure the change in gateroad loading, six borehole pressure cells to measure the loading in the pillars, three six-channel roof extensometers to measure roof sag, four convergence measurements on the cribs to measure the crib loading, and a multipoint borehole extensometer to measure the pillar expansion. The instrumentation was all connected through two multiplexers to a single Campbell Scientific permissible datalogger located about 350 feet outby the instruments. The goal of the project was to record all of the measurements as both longwall faces passed the site of the instrumentation and to use the data to calibrate numerical models.This report describes the recording of all of the measurements taken as the first panel approached and then passed the instrumentation site. This study provided valuable data related to the ground response and support performance that will be used to improve safety in longwall gateroads.INTRODUCTIONA longwall mine in northern West Virginia was selected as a second study site for an ongoing research project into gateroad layout and support design. The area was affected by a transition from limestone to sandstone in the roof. The entries were 16 feet wide, and the height was approximately 80 inches. The layout for the longwall panels was 1,170 feet wide by 4,000 feet long. The panel configuration was right-handed, and a three-entry gateroad was used between panels. The pillars next to the headgate were 137.5 feet by 115 feet center-to-center, and the pillars next to the tailgate were 275 feet by 100 feet center-to-center, with the crosscuts at 60 degrees. The width of the gateroad was a total of 215 feet."

Jan 1, 2018

By P. M. Lin

The problem of abandoned mine land (AML) subsidence is getting more severe because abandoned mine lands which used to be located in the remote areas have been gradually developed into suburbs or even urban areas. Abandoned mine subsidence is also becoming more common than before because the time-dependent effect of exposed underground materials. These materials will deteriorate gradually and cause subsidence as time passes. Subsurface conditions of abandoned mines are seldom known to the public. Mine maps are not always available. If the mine mans are available, their accuracy are very - often questionable. In addition, the most common damages to surface structure and ground surface due to mine subsidence can also be created by other non-mining related geological hazards. These factors make the study of abandoned mine subsidence significantly complicated, tedious, and inconclusive. For instance, the cause, time, and amount of surface subsidence can be predicted with relative accuracy during active mining. However, it will be a considerable challenge to do so on abandoned mine subsidence. If abandoned mine subsidence can be predicted in advance, then the damages can be held to a minimum. However, this prediction technique is not yet well developed. Therefore, remedial measures require more attention. In order to have effective remedial measures, the real cause of the damage should be determined first. This paper describes the approach which was employed for the determination of abandoned mine subsidence. A site investigation was made first. According to the information obtained from the site investigation, a hypothesis was set up. Then the instrumentation was used to prove the hypothesis. By going through the procedures for several cases, a guideline which can be used by the inspectors to inspect abandoned mine subsidence will be established.

Jan 1, 1987

By M. K. Larson

The U.S. Bureau of Mines and Cyprus Shoshone Coal Corp. conducted a study of deformation mechanisms around a longwall gate-road system in an underground coal mine. Of particular interest was roof deformation over the headgate entry. The strata above and below the coal seam are very weak, carbonaceous mudstones that have planes of weakness oriented along the bedding. Visual observations of previous gate roads over several years suggested that deformation was time dependent and resulted in creep along joints or crack growth. Instruments were installed at a test site to measure deformation around the entry, strew changes in the pillar, and loads transferred to support systems. Multipoint extensometers, instrumented bolts, instrumented trusses, biaxial stressmeters, borehole pressure cells, and single-point extensometers were installed. Monitoring continued until the longwall face passed the test site by 38.7 m (127 ft). Results show that fracture zones arched over the entry from both ribs, most bolts and trusses were loaded past their yield point, and the largest change in secondary principal stress was almost horizontal in the pillar. Displacement measurements in the roof showed classic primary creep.

Jan 1, 1995

By Dan Payne

Roof falls and other ground control incidents make up a significant portion of fatal accidents in underground mines. BHP Billiton has undergone a review of all fatalities in their operations and divided these into 10 fundamental categories of which underground ground control is one. Each underground roof fall fatality was investigated and the root causes workshopped to develop a protocol for the control of fatalities due to falls of ground. This protocol sets out 22 requirements which each BHP Billiton underground mine site must comply with. This paper describes the development, requirements and application of the protocol within BHP Billiton.

Jan 1, 2006

By Yvette Heritage

"The risk of fatalities from rib failure is still prevalent in the coal mining industry. This risk has prompted further research to be conducted on rib deformation in order to understand the mechanisms of rib failure, with the long-term objective being to improve rib support design. This paper presents the results of ACARP research project C25057, which investigated the mechanics and drivers of rib failure. The results of rib deformation monitoring at three different mines in Australia provides rib deformation characteristics for overburden depths ranging from 160 m to 530 m. Monitoring includes deformation during development drivage conditions and during the longwall retreat abutment stress environment. The rib deformation monitoring covered three different seams: the Goonyella Middle Seam, Ulan Seam, and Bulli Seam in the Bowen Basin, Western Coalfield, and Southern Coalfield, respectively. The observed mechanisms driving the rib deformation ranged from bedding shear failure along weak claystone bands to vertical shear fractures to kinematic failures driven by shear failure dilation. The variation in mechanisms of rib failure, together with the seemingly consistent method of rib support design, prompts the question: What exactly is the role of rib support?INTRODUCTIONThe current risk of rib fatalities in the coal mining industry has prompted further research into understanding the mechanisms of rib failure. Three Australian mines assisted further research by providing sites for rib deformation studies as part of the Australian Coal Association Research Program (ACARP) project C25057. The mines included in this study were Moranbah North Mine, Ulan West Mine, and Appin Mine. This paper provides key results of the rib deformation monitoring relevant to assessing the mechanisms of rib deformation.The approach of monitoring rib deformation and rib support loads was used to measure and characterise the dynamic rib deformation present in both development and longwall retreat stress environments. The characterisation of rib deformation, together with rock failure modelling, was used to determine the mechanisms for failure within the rib and to assess the interaction of rib support with the failure process. The mechanisms of rock failure are considered an important factor in understanding the drivers for the failure. Consideration of the site-specific failure mechanisms can provide for a more tailored support design."

Jan 1, 2018