Search Documents

By Bruce K. Hebblewhite

Tower Colliery is a longwall mine operated by BHP Coal Illawarra Collieries, Southwest of Sydney, Australia It mines the Bulli Seam at a depth of approximately 450m. The surface topography overlying the mine consists of several steep-sided river gorges, up to 68m in depth, which run at oblique angles across a sloping terrain Apart from some light rural development, the surface land is essentially natural bushland, but is traversed by a major freeway. This crosses one of the gorges on twin, six-span, box-girder bridges, with bridge piers up to 55m in height. Consequently, a major surface subsidence monitoring program has been in place for several years now, including intensive conventional, GPS and E DM surveying, plus real-time monitoring of critical components of the bridge structure. Although the bridge and freeway are outside the conventional angle of draw' subsidence influence criteria, and have seen only negligible vertical deformation as a result of mining, there has been widespread evidence of regional horizontal deformation of the land surface, large distances away from the mining area The effect at the bridge has been well within acceptable tolerances, primarily because of the regional nature of the movements, with very little differential movement observed at the bridge piers Gorge closure and evidence of large headlands of land moving `en masse' have been observed. Horizontal movements of hundreds of millimetres have been recorded in some locations where gorge closure has been monitored. Possible explanations of these movements include one or a combination of mechanisms such as pre-mining stress relaxation. valley notch effects, valley bulging, regional joint patterns, movement toward active goaf areas, vertical gorge shearing' and shear failure of horizontal bedding planes below the surface This paper presents a case study of the regional horizontal ?subsidence displacements? measured during mining. and a discussion of the possible explanations for these phenomena

Jan 1, 2000

By Liane J. Terrill

A 9O) ft (275 meter) section of a highly fractured beam of halite was mined from the roof of a supported thirteen year old drift at the Waste Isolation Pilot Plant (WIPP). The operation was conducted with a continuous miner and allowed the unique opportunity to collect spatial information on roof beam geology and to observe ground support conditions during the mining advance. Photographs and fracture maps of the mining face document the progress of the operation and the deteriorated condition of the strata. This case study details the drift's excavation and support sequences. the geomechanical response, and the conditions found in the exposed roof beam.

Jan 1, 1997

By Herryal Z. Anwar

In recent years, many both mining and civil engineering projects are developed in the area which may be categorized unstable, such as fractured and jointed rocks or "water sensitive rocks". For example, in underground coal mining, in which the floor strata normally consist of weak shale, the problem that may arise in roadway is floor heaving. In this case cement injection in borehole appears to be an economically effective method in order to make roadway more stable. This method may be also applied in the projects in which the constructions are laid on fractured and jointed rock. Nevertheless, the successful cement injection is much dependent on the water-cement ratio and the injection technique. This paper discusses the application of cement grouting to improve the ground stability in longwall mining, the laboratory experimentation of cement grouting and the method of floor injection.

Jan 1, 2000

By Chris Strawson

Moranbah North is a modern longwall operation mining premium coking coal in the Northern Bowen Basin, Central Queensland. Australia Moranbah North Coal (MNC) is owned and operated by Anglo Coal Australia. Extracting approximately 4.5m of the Goonyella Middle seam using a single longwall, the mine produces 5 to 6 Mt per annum. The weak coal (4.5 MPa), low strength laminated immediate roof, and strong upper roof sandstones, make operation of the longwall at depths in excess of 250m geotechnically challenging. In the past, there have been a number of production delays due to geotechnical issues. Roof instability resulted in a long stoppage on Longwall 105, and the eventual relocation of the face further outbye in the block. (Figure 1). When mining commenced in LW106, there was a requirement for uninterrupted production, particularly in the more demanding inbye area of the panel. Following discussions with a number of Geotechnical experts, it was decided to narrow the face, and test the theories of reduced face weighting due to spanning of the goaf across the panel. A new on line chock monitoring system, and microseismic monitoring was installed in order to characterise the difference in the rockmass response, as the panel width changed from 175m, to 265m, and then 300m. The nature of the goaf formation and impacts on face loading and production are discussed, having the unique opportunity of three different face widths within the same area.

Jan 1, 2007

By Dennis R. Dolinar

Roof falls, even of supported roof, still constitute a major hazard in underground mines. However, associated with any fall or instability is a pattern of roof movement. Therefore, the National Institute for Occupational Safety and Health, Pittsburgh Research Center, has been conducting research into the development of practical extensometer systems that can be used to measure this displacement and to determine if a roof fall may occur, thus increasing miner safety. For extensometers to be used in the detection of potential roof falls in coal mines, an understanding of the movement and displacement rates that will lead to roof failure is required. Because roof falls are unpredictable, it is often very difficult to obtain this information. Therefore, in a coal mine in the lower Kittanning seam in Pennsylvania, a room widening experiment was conducted to intentionally cause a roof fall while roof movement data was collected. In this experiment, two adjacent rooms 5.5 m (18 ft) wide supported with 1.5 m (5 ft) resin-grouted bolts and instrumented with extensometers were widened to 9 m (30 ft). In one of the rooms, 3.6 m (12 ft) cable bolts were installed as supplemental support. In the room with no additional support, a roof fall occurred 72 h after the room was widened. Much of the 3 cm (1.2 in) of movement in this room resulted from the instantaneous and transient response to mining with displacement rates up to 7.6 cm/d (3 in/d) being measured. This was followed by a steady state displacement phase with a rate of 0.43 cm/d (0.17 in/d). Just 12 h before the fall, movement deeper in the roof caused the rate to accelerate to 1.1 cm/d (0.44 in/d). The roof in the room with the supplemental cable support did not fall even though the total roof deformation was over 7.6 cm (3 in). Significant roof movements and strains in the cabled room were detected to a depth of 3 m (10 ft) while maximum cable loads were over 180 kN (40,000 lbf). Essentially, the roof was in postfailure with the cables maintaining the material, while roof stability was indicated by a steady state displacement rate of only 0.025 cm/d (0.01 in/d) at the end of the test.

Jan 1, 1997

By Mikko Ahola

This paper describes recent innovative analyses conducted by the Bureau of Mines to demonstrate the application of the boundary-element method in evaluating the effectiveness of caving chambers or sacrificial entries to relieve the stress conditions initiating cutter roof failure in underground coal mines. The analysis assumes that cutter roof failure results when the shear strength of the roof rock at an entry corner is exceeded by the applied shear stress. The applied shear stress is due to large differences between the horizontal and vertical in situ stresses known to exist in many coal mining districts experiencing cutter roof failure. The results of boundary-element analysis suggest that driving an arched lead entry in advance of adjacent rectangular entries and allowing it to cave significantly reduces the difference between the principal stresses at the corner of the rectangular entry, thereby lowering the maximum shear stress. Slippage of the immediate roof along horizontal bedding planes into the caved entry is shown to further reduce the stress conditions in adjacent entries. Practical applications of this stress control technique to longwall and room-and-pillar mining are discussed.

Jan 1, 1987

By Ry Stone

"There have been many design practices utilised within the coal mining industry to arrive at the minimum densities of primary ground support required during roadway development. This paper demonstrates the practical use of empirical databases, and focuses on the main drivers for ground support as demonstrated in conceptual models.Golder Associates’ empirical databases used for ground support include a Primary Roof Support Database and a Primary Rib Support Database. Both are based on successful ground support designs installed in mines in Australia, the US, the UK, South Africa, New Zealand, and Europe. The term “successful” refers to those designs that were used on a repeated basis for the purpose of roadway development.The Primary Roof Support Database indicates that the major factors influencing successful roof support designs are roof competency, expressed as the Coal Mine Roof Rating (CMRR), and in situ stress. As roof displacement is essentially a function of horizontal stress and roof competency, in order to provide some form of measure as to the likely magnitude of roof deformation during roadway development, the depth of cover is divided by the CMRR to arrive at a “Stress Strength Ratio” (SSR). The database indicates that the higher the SSR, the greater the likelihood that the roof will require higher densities of support.In regard to the Primary Rib Support Database, it is evident from the current database that the primary factors affecting the capacity of rib support required for a successful design are roadway height and depth of cover. In order to provide some form of measure as to the likely magnitude of rib deformation during roadway development, the depth of cover is multiplied by the height of the roadway to determine a “Rib Deformation Rating” (RDR). Similar to the roof, the database indicates that the higher the RDR, the greater the likelihood that the rib will require higher densities of support.These databases have been used to help determine the minimum primary ground support designs required at many mine sites in Australasia, Europe, and the US. This paper will demonstrate the effectiveness and practicality of these databases at two selected mines in Australia and the US.In order to improve the Primary Rib Support Database, this paper will also propose a new rib deformation rating based on the addition of site specific coal strength data for the Australian mines. The proposed rating attempts to capture the main variables that define the behaviour of a buckling column."

Jan 1, 2015

By Robert C. Speck

Floor heave or deformation of the mine floor into the mine opening is a problem which has plagued coal mines in this country and others. In mining areas where room and pillar mining is practiced, floor heave generally occurs when the stress applied to the floor material by a coal pillar exceeds the bearing capacity of the floor strata. When the floor strata beneath the coal pillar fail, the pillar moves downward and displaces the material under it. This material, in turn, moves outward and upward into the mine opening (Figure 1). As the underlying materials fail, the load supported by the coal pillar may be transferred to adjacent pillars. If these are marginally stable, they too may become overloaded and push into the floor. Thus, floor heave can spread through a large portion of the mine in a progressive manner. As the pillars push into the floor, differential movement and flexure of the roof strata may cause them to weaken and fail, resulting in subsidence of the ground surface above the mine. This paper describes the problem as it was manifested in the Zeigler Coal Company No. 5 and Murdock room and pillar coal mines near Murdock, Illinois, and reports the results of a U. S. Bureau of Mines- sponsored study conducted by the University of Missouri-Rolla. During the course of the study, floor heave in the two mines hindered the transportation of men, machines, and coal to and from the working mine-face, interrupted ventilation plans, drastically increased roadway maintenance costs, intensified safety and strata control problems, destroyed large pieces of equipment, and, several times, pre- vented access to otherwise minable coal resources. The ultimate objective of the study was to develop one or more simple procedures to allow detection of a potential floor heave problem during the exploration phase of mine design--before initiation of production mining.

Jan 1, 1981

By P. Forrest

Based on the results of mathematical analysis, photoelastic modelling, and case studies, the mechanisms of longwall under- mining interaction has been thoroughly investigated. The effects of using yield pillars in combination with rigid pillars in lower seam mine design have been found to provide significant improvement in ground conditions during undermining. Off- setting of solemnized longwall panel entries relative to upper-seam remnant structures has proven to be effective in alleviating adverse stress conditions.

Jan 1, 1988

By K. Biswas

So far, all pillar design methods or approaches consider the coal seam as a uniform structure From some mine visits in northern Appalachian Region. it is found that some coal seams have binder or parting material within the coal scan with varying thicknesses and numbers- And it has also been found that these kinds of hinder materials tire prone to weathering when exposed to ambient mine moisture In this paper an attempt has been made to study the weathering susceptibility of parting materials and coal when exposed to moisture and a two dimensional finite element analysis has been carried out to study the effect of the presence of partings on the structural integrity of the coal pillar in terms of short-term and long-term stability.

Jan 1, 1995

By Dale A. Didcoct

Through the combined efforts of the C. S. Bureau of Mines, the coal industry, and Burrell Construction and Supply Company, New Kensington, PA, a steel fiber reinforced concrete crib block to improve coal mine safety in the area of roof control has been developed and is currently in use commercially. The development objective was to improve health and safety conditions with a stiffer, stronger, nonflammable roof support at a competitive cost. During the time this method of roof control has been in use in the mining industry, it has proven to be both functionally and economically effective.

Jan 1, 1982

By Jeffrey Johnson

To measure the loading behavior of friction bolts, researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) installed strain gauges on the interior of friction bolts and developed a battery-powered miniature data acquisition system (MIDAS) that fits inside the hollow portion of the friction bolt. The advantages of this system are that it is protected from face blasts and eliminates the need for external wiring. Laboratory pull-out tests showed that friction bolts installed in a concrete block with resin were loaded to about 1.8 tons/ft of bolt length; bolts installed without resin were loaded to 1.3 tons/ft. Three strain-gauged friction bolts were installed at Hecla Mining Company's Gold Hunter Mine, Mullan, ID, in the wall or rib of a mechanized cut-and-fill stope. The object of these tests was to establish an installation procedure for the bolt-and¬MIDAS combination and to evaluate performance. The stope was advanced in three 15-ft increments and strains induced in the rock bolts by stress changes in the rock were recorded every 30 minutes. The MIDAS proved to be rugged enough to withstand the shock and vibration from nearby (5 ft) face blasting. Data from MIDAS showed that the friction bolt installed with resin was the most sensitive to each face advance. It showed a steady increase in loading to a maximum value of 1000 microstrain. The friction bolt installed without resin showed stick-slip behavior with loads to a maximum of 400 microstrain before the stope was completed.

Jan 1, 2003

By Michael Karmis

During the last 25 years, technological advancement and subsidence research have resulted in more accurate and diverse prediction capabilities. The work presented in this paper focuses on the development of integrated prediction capabilities for dynamic deformation indices and for strains over sloping terrain. In order to assist subsidence engineers with accurate prediction methodologies, the research also addresses the development and validation of techniques that can enable model calibration using alternative measured subsidence parameters such as horizontal or ground strain instead of the traditional vertical subsidence values. This paper presents the basic concepts and validation of the above mentioned enhanced prediction and control methodologies, which are necessary for effective assessment and control of mining-induced subsidence, using examples and case studies. In addition, a risk assessment approach for evaluating landscape stability over mined areas is presented. The enhanced prediction methodologies have been incorporated into the Surface Deformation Prediction Software (SDPS) package.

Jan 1, 2008

By S. J. Jung

The goal of this research is to demonstrate how optimization methodology can be coupled with the finite element method for greater stability of underground mine openings. As a result of increasing mining depth and intersection of geologic discontinuities, mining environments are becoming more complex. Current design procedures are rapidly becoming inadequate. In this research, the finite element method has been coupled with optimization criteria to design more stable and safe underground openings

Jan 1, 1993

By Jamal Hematian

Understanding the behaviour of rocks in a high horizontal stress field, such as that in Australia, is critical when analysing the stability of underground structures. This paper addresses the significance of the post-failure behaviour of rocks on the stability of underground structures which are under the influence of a high horizontal stress field. The research work was conducted through a combination of numerical modelling, laboratory testing and field investigation. A number of 2-D FE model of roadways were constructed based on the data obtained from laboratory testing and field investigations. The models were then analysed using three different solution techniques; simple linear-elastic, non-linear elastic-plastic and elastic-plastic with consideration of post-failure behaviour (softening model). Results indicated that the post-failure behaviour of rocks significantly influence the stress and displacement patterns around the roadway. The stress and displacement patterns as well as the extent of the yield zone around the roadway predicted by the softening model were in good agreement with that from the field study. Based on the results of the study, an appropriate support system has been suggested to govern the stability of roadways.

Jan 1, 1994

By Michael Jenkins

This paper reviews the history of rock burst research in the Coeur d'Alene Mining District of northern Idaho over the last 30 years. Rock bursting is a problem because of a combination of geological factors in the region--complex structure, high horizontal stresses, and strong, brittle rock that readily stores strain energy. The Bureau of Mines has cooperated with industry to study rock burst phenomenon for many years. Early work focused on methods to mitigate bursting problems within the context of existing mining methods. In the 1970's, researchers began investigating methods for altering or controlling conditions that lead to rock bursts. These control measures become part of the stope development that precedes mining or are changes in the mining process itself. Although, researchers continue to develop microseismic techniques, the major research effort focuses on developing a new mining method to reduce the number and severity of rock bursts in order to improve safety and increase productivity in the Coeur d'Alene Mining District.

Jan 1, 1987

By Dennis Dolinar

"Tailgate entries in U.S. longwalls can be subjected to high loads and deformations. Therefore, tailgate entries are generally supported with varying types and amounts of standing support. However, even with standing support, roof falls and blockages can occur in the tailgate when the support system is not properly designed. Safe and efficient operation of a longwall face requires the selection of the appropriate type and amount of standing support. Because of the importance of maintaining a safe and functional tailgate entry, the National Institute for Occupational Safety and Health (NIOSH) is currently developing a standing support design methodology based on the ground reaction curve. Using the ground reaction curve for design requires that the ground and support interaction be quantified. This can be accomplished by the installation and analysis of data from instrumented field sites. Although necessary, the field results cannot develop the complete ground reaction curve. Numerical models, calibrated to the field results, are used to establish the complete ground reaction curve. In the present study, data was obtained and evaluated to establish points for calibration of the ground reaction curve for two western longwall operations.One test site, Mine A, was located at a depth of 1,550 ft. At this site, the floor consisted of siltstone, while the roof was an interbedded siltstone and sandstone. Because of the depth, a double row of22-in diameter CANs1 were installed to support the tailgate. Both the first and second longwall panels have mined past the instrumented site.The second site in Mine B is at a depth of only 760 ft. The floor at this mine consists of a weak shale/mudstone and the roof consists of thick, top coal overlain by weak shales. At this site, a double row of pumpable cementitious cribs was installed. The second test site has only been subjected to side abutment loading from first panel longwall mining.The measurements indicate that the support at both mines was heavily loaded when subjected to the side abutment loading from first panel mining. At the deeper site, the support began to yield when the face was more than 300 ft outby during second panel mining. In comparison to results from previous test sites in the Pittsburgh Seam and Illinois Basin, the amount of support loading and roof-to-floor convergence was an order of magnitude higher at the western sites. This has resulted in a significant difference in the position and shape of the ground reaction curves."

Jan 1, 2010

By D. L. Price

This paper presents a method of measuring field power consumption of shearers and deriving specific energy consumption versus shearer haulage speed performance curves. A description of a computer program which simulates the cutting action of a shearer drum is presented. A comparison between the field specific energy curves and the computer simulation results is made. The simulation results compare well with the field data where all the coal seam is being cut by the shearer. The computer simulation results give hack-calculated field pick force cutting characteristics, which allow the performance of the shearer to be predicted for other operating conditions, e.g. effect of changes to pick lacing, effect of changing the drum rotational speed, allows the calculation of power requirements for a particular production rate.

Jan 1, 1992

By Zach Agioutantis, Christopher Mark

"Thirty years ago, the Analysis of Longwall Pillar Stability (ALPS) inaugurated a new era in coal pillar design. ALPS was the first empirical pillar design technique to consider the abutment loads that arise from full extraction, and the first to be calibrated using an extensive database of mining case histories. ALPS was followed by the Analysis of Retreat Mining Stability (ARMPS) and the Analysis of Multiple Seam Stability (AMSS). These methods incorporated other innovations, including the Coal Mine Roof Rating (CMRR), the Mark-Bieniawski pillar strength formula, and the pressure arch loading model. They also built upon ever larger case history databases and employed more sophisticated statistical methods.Today, these empirical methods are used in nearly every underground coal mine in the US. However, the piecemeal manner in which these methods have evolved resulted in some weaknesses. For example, in certain situations, it may not be obvious which program is the best to use. Other times the results from the different programs are not entirely consistent with each other. The programs have also not been updated for several years, and some changes were necessary to keep pace with new developments in mining practice.The Analysis of Coal Pillar Stability (ACPS) now integrates all three of the older software packages into a single pillar design framework. ACPS also incorporates the latest research findings in the field of pillar design, including an expanded multiple seam case history data base and a new method to evaluate room and pillar panels containing multiple rows of pillars left in place during pillar recovery. ACPS also includes updated guidance and warnings for users and features upgraded help files and graphics.INTRODUCTIONPillar design is one of the fundamental elements of mining engineering. Pillars are necessary to control the great weight of the overburden during all phases of underground mining. Without stable pillars, ground control is impossible."

Jan 1, 2018

By David Newman

Coal refuse impoundments and underground mines are frequently sited in close vertical and horizontal proximity in the valleys of the Southern Appalachian coalfield. The steep V-shaped valleys provide the volume necessary for slurry storage against a coarse refuse embankment that is constructed across the valley mouth. The presence of coal outcrops on the valley walls provides economic access to mineable coal seams that may be located under several thousand feet of overburden beneath the adjacent ridges. In some instances where the underground mine precedes the slurry impoundment, the type of mining (partial or complete extraction) and pillar centers were selected without consideration for the potential future use of the valley as an impounding structure. The high standard established for the design and stability analysis of the coarse refuse embankments is clearly illustrated by the absence of an embankment failure in the thirty-one years since Buffalo Creek. However, the recent Martin County slurry spill focused attention on a thorough geotechnical analysis to prevent a connection between the flowable slurry and the mine void. The overburden, roof, pillar, floor, and outcrop barrier stability are examined to quantify the break through potential. The strength and physical properties of the consolidated fine refuse are also important since this material is often the most well-defined and quantifiable barrier separating the slurry and mine void. Because each site is unique, the appropriate analysis ranges from the calculation of roof, pillar, and floor safety factors to detailed numerical modeling of the mine workings and the determination of ground deformation and strains resulting from mine subsidence. The method of refuse disposal may be altered to slurry cells where the accuracy of the mine maps, extent of mining, type of mining (development or retreat) cannot be reliably verified or the break through analysis does not produce an acceptable level of risk. Case histories from the Southern Appalachian coalfield are used to illustrate the application of methodologies to quantify the break through potential of coal refuse impoundments.

Jan 1, 2003