Search Documents

By John F. MacDonald

This paper describes the driving of a 400 m long by 25 m diameter highway tunnel through sensitive, overconsolidated silts and clays. The design concept requires the construction of the permanent support system, consisting of 24 concrete filled perimeter drifts, before excavating the mass core. General construction procedures used during the construction of the perimeter drifts are described.

Jan 1, 1985

By Raymond W. Henn

The 32nd annual short course ?Grouting Fundamentals and Current Practice? was held at the Colorado School of Mines, June 13-17, 2011. The field demonstration portion of the course was conducted June 16 at Baski Inc.?s yard in Denver, CO. The full-scale field demonstration presents many types of drilling and grouting equipment in operation as well as numerous grouting methods per-formed under various field conditions. As part of the field demonstration, the class was shown the proportioning, mixing, testing and injection of various cement grout mixes into sand columns under controlled and recorded conditions. These sand column demonstrations have been conducted under controlled and measured conditions each year since 1999 as part of the short course. The sand column demonstrations were conducted prior to 1999, but with less quality control and minimal record keeping of the proportioning, mixing, testing, injection pressures and the final permeation results.

Jan 1, 2011

By S. Rupprecht

"This article addresses the prevalence of poor public reporting practices of coal exploration results, coal resources and coal reserves in southern Africa. Currently, the reporting of coal tonnage without supporting coal qualities or saleable tonnes and quality is a poor reporting practice that occurs far too often. Not all coal is equal — therefore it is extremely important that investors or potential investors are provided with the full details of both run-of-mine (ROM) and saleable coal tonnage, their associated qualities and other material and relevant information.Competent or qualified persons should note that publicly reported information should be sufficient to enable an informed reader to make a reasonable and balanced assessment of the significance of the information provided. “Companies are encouraged to provide information in their public reports, which is as comprehensive as possible (CRIRSCO, 2013).” However, too often this isn’t the case, and material matters are either not reported or inadequately disclosed.According to the South African National Standard (SANS) 10320:2014 draft document, “tonnage and coal quality that will be available for sale, either in the raw ROM state (raw saleable) at a specified moisture content, or after beneficiation of the ROM coal by processing operations to produce materials at specified qualities, size ranges and moisture contents. The assessments must demonstrate that at the time of reporting, the marketing of the products is reasonably justified. The basis of the predicted practical product yield to achieve the saleable coal reserve must be stated. The moisture basis of reporting shall be stated.” An example as to why coal qualities are so important to the public, the requirements of South Africa’s electric public utility (Eskom) power stations are detailed in the followint paragraphs. The Kendal power station, commissioned in 1988, operates at a calorific value (CV) range of 19 to 20 MJ/ kg, an ash content between 29 and 34 percent and volatiles between 20 to 21 percent. Other power stations, such as Kriel or Hendrina, may require different qualities, such as a CV range of 22 to 23 MJ/kg, an ash content between 20 and 28 percent and volatiles between 22 to 23 percent. Thus, in terms of domestic saleable coal, it is not just about reporting the coal qualities but also informing the investor as to which power station the coal is intended to be sold as “boilers are designed to burn particular qualities of coal” and “it is not always possible to transfer coal between stations because of different quality requirements at each station (Chetty, 2010).” Sulfur content is another important quality with the ideal coal content having a quality of less than 1 percent sulfur."

Jul 1, 2019

By Clifford B. Farris

Introduction Shale Mining Problems The mining problems an oil shale operator will face are largely determined by the process. Candidate oil recovery processes are surface (above ground processing of mined oil shale), modified in situ (underground with some shale removed), and true in situ (completely underground with no shale removed). The shale removed for modified in situ (MIS) is generally processed by surface techniques. The mining problems are different for each category. Fig. 1 depicts the diversity of western shale deposits. Mining for surface operations will employ underground mining techniques in common use but the scale will be larger. A typical oil shale operation is expected to require 75,000 to 250,000 st (68 000 to 226 800 tons) a stream day of crushed oil shale. This is above the upper limit of current mining operations. Major problems in¬clude: (1) lack of good engineering design properties for oil shale, especially when interbedded with saline minerals at depths below 1,000 ft (305 m); (2) presence of water, hydrogen sulfide, and methane in some areas; (3) necessity for mine disposal of as much retorted oil shale waste as possible; and (4) control of en¬vironmental impacts of mining. Portions of the oil shale deposits in Colorado, Wyoming, and Utah and significant portions of the Devonian shales in the eastern U.S. are adapted to surface mining. No major technological problems are apparent outside overburden thicknesses up to 1,000 ft in the West. However, numerous political and environmental dif¬ficulties have arisen. One major oil shale developer cancelled a planned surface mining operation and currently is pursuing a modified in-situ plan. The eastern shales are closer to the surface than the western, but suffer from many of the same environmental and political problems. Modified in-situ operations face much more severe mining problems than surface efforts. Because the mined stope (called an in-situ "retort" by processors) acts as a retorting process vessel subject to gas flow, combustion, and temperatures between 1,500° and 2,000°F, mining is under highly restrictive limitations. This processing method involves removing between 20 and 40% of the shale deposit and then blasting the roof and walls into the mined space, where the oil is recovered by retorting. Major problems are: (1) swell factor severely limited; (2) need for consistent size distribution of blasted shale; (3) even filling of stope (in-situ retort) by blasted shale with consistent permeability throughout; (4) scaleup of blasting techniques, after optimization; (5) protection of retort pillars and roof during and after retorting; (6) prevention of groundwater percolation; (7)use of ANFO explosive in wet holes; (8) disposing of surface-retorted shale waste in stope; and (9) restoration of site. True in-situ operations are less well developed than surface or MIS processes. No actual mining is done, as the true in-situ processes generate permeability in the highly

Jan 1, 1980

By Wolfgang Gütter

India is targeting to boost its electrical capacity from 100 GW to 200 GW within the next 10 years. The National Hydroelectric Power Corporation (NHPC) has decided in2001 to take execution of the 800 MW Stage-II of the prestigious 2,051 MW Parbatihydrol electric project in Kulu district of the northern province Himachal Pradesh. Two parallel 30° inclined underground pressure shafts of 1.542m in length each will be excavated in different geological formations and lined with hexagonal concrete segments by a hard rock double shield TBM. That kind of heading will be a novelty to India and an innovative method for inclined pressure shafts. The 4.88m Mitsubishi DSTBM will be assembled underground on a swivelling steel platform especially designed for the launching as well as for the acceptance of the TBM in the upper cavern of each shaft. The hexagonal segmental lining system causes a significant higher job safety than an open TBM with conventional support. Each ring consists of four honeycomb segments with 20 cm thickness. After finalisation of the excavation a steel liner will be installed and concreted. The Joint Venture Jäger-Seli will perform the two pressure shafts as a sub-contractor for the Indian company Gammon India Ltd.

Jan 1, 2005

By William Reininger

Microtunneling provides a necessary solution for multiple utility crossings associated with the New York Metropolitan Transportation Authority Capital Construction Company?s (MTACC) Eastside Access Project for the Long Island Rail Road. Construction of four TBM tunnels and their approach structures at the eastern end of the project in Sunnyside, Queens required significant modification and expansion of the railroad infrastructure at this location. Maintenance of railroad traffic during project construction is a principal requirement. As a consequence fourteen (14) utility crossing segments are being installed under active traffic by microtunneling methods. Microtunnels were installed in a variety of conditions including depths, types of soils and construction restraints.

By John M. Dale

Now that the price of sulfur has reached unexpected high levels, it is little wonder that sulfur from surface ores is again receiving attention. In most instances, it is advantageous for an ore to be at or near the surface. However, it is a distinct disadvantage for sulfur ore to be close to the surface because it precludes the use of the Frasch process. The Frasch process depends on the presence of at least 180 m of uniform overburden to allow pressure injection of superheated water into the sulfur-bearing formation to melt the sulfur. In the Frasch process, sulfur separates cleanly from the gangue underground and comes to the surface in a very pure form. Surface sulfur deposits, particularly those in the Western Hemisphere, exist largely due to volcanic activity, and sulfur separation from the gangue is a formidable technical problem. None of the surface deposits are large compared to some of the Frasch deposits, but at the present sulfur price, they are certainly of economic importance. From the turn of the century until 1975, the price of sulfur was for the most part $18-$28/t. However, with the price of sulfur now over $154/t, there are a variety of technical alternatives to consider for sulfur surface ore separation that may not have been economically attractive a few years ago.

Jan 9, 1981

By John R. Sturgul, Elizabeth Yost

The number of Native Americans presently working as mining engineers is extremely low-perhaps three in the entire US. At the New Mexico Institute of Mining and Technology, it was felt that introducing high ability students to mining engineering at the high school level would encourage more to consider mining engineering as a career. New Mexico Tech, in Socorro, NM, has initiated a continuing summer college program for Native American high school students. The program, which began in the summer of 1980, is designed to introduce participants to college life, enrich their high school curricula, and expose them to the problems and challenges of a career in mining and related engineering fields. Students From reservations throughout New Mexico with a demonstrated aptitude for science and mathematics were encouraged to apply for admission. Preference was given to high school sophomores and juniors since it is hoped that students will want to return for a second year before graduating from high school and beginning university studies. The program seeks to impress upon the students the need fir Native Americans in the fields of seience and mineral engineering.

Jan 7, 1981

By Hyung-woo Kim, Kiyoung Sung, Sup Hong, Jung-Yeul Jung

Many concepts for the commercial production of deep-seabed manganese nodules have been studied since the 1970s. However, the bearing capacity of the deep seabed is not strong because it is composed of fine particles with high moisture content. So it is impossible to carry manganese nodules in the collection system. Therefore, the validity of continuous mining by riser pipe from the seabed to the vessel is highly appreciated. A continuous mining system is composed of mining vessel, lifting pipe, buffer system, transport tube (flexible pipe), and self-propelled mining robot. A conceptual diagram of this system is shown in Fig. 1(a). Korea Research Institute of Ships and Ocean Engineering (KRISO) developed a deep-seabed self-propelled mining robot called "MineRo" to collect manganese nodules in 2012 (as shown in Fig. 1(b)). In 2013, real sea experiments at around 1380 m depth were carried out to evaluate the collecting and driving performance of MineRo. However, we found that the roller in MineRo did not work well at times. To elucidate the problem, we analyzed the rheological characteristics between the bushing and drive shaft under deep-water conditions.

Sep 1, 2014

By Clifford B. Farris

Introduction Shale Mining Problems The mining problems an oil shale operator will face are largely determined by the process. Candidate oil recovery processes are surface (above ground processing of mined oil shale), modified in situ (underground with some shale removed), and true in situ (completely underground with no shale removed). The shale removed for modified in situ (MIS) is generally processed by surface techniques. The mining problems are different for each category. Fig. 1 depicts the diversity of western shale deposits. Mining for surface operations will employ underground mining techniques in common use but the scale will be larger. A typical oil shale operation is expected to require 75,000 to 250,000 st (68 000 to 226 800 tons) a stream day of crushed oil shale. This is above the upper limit of current mining operations. Major problems include: (1) lack of good engineering design properties for oil shale, especially when interbedded with saline minerals at depths below 1,000 ft (305 m); (2) presence of water, hydrogen sulfide, and methane in some areas; (3) necessity for mine disposal of as much retorted oil shale waste as possible; and (4) control of environmental impacts of mining. Portions of the oil shale deposits in Colorado, Wyoming, and Utah and significant portions of the Devonian shales in the eastern U.S. are adapted to surface mining. No major technological problems are apparent outside overburden thicknesses up to 1,000 ft in the West. However, numerous political and environmental difficulties have arisen. One major oil shale developer cancelled a planned surface mining operation and currently is pursuing a modified in-situ plan. The eastern shales are closer to the surface than the western, but suffer from many of the same environmental and political problems. Modified in-situ operations face much more severe mining problems than surface efforts. Because the mined stope (called an in-situ "retort" by processors) acts as a retorting process vessel subject to gas flow, combustion, and temperatures between 1,500° and 2,000°F, mining is under highly restrictive limitations. This processing method involves removing between 20 and 40% of the shale deposit and then blasting the roof and walls into the mined space, where the oil is recovered by retorting. Major problems are: (1) swell factor severely limited; (2) need for consistent size distribution of blasted shale; (3) even filling of stope (in-situ retort) by blasted shale with consistent permeability throughout; (4) scaleup of blasting techniques, after optimization; (5) protection of retort pillars and roof during and after retorting; (6) prevention of groundwater percolation; (7)use of ANFO explosive in wet holes; (8) disposing of surface-retorted shale waste in stope; and (9) restoration of site. True in-situ operations are less well developed than surface or MIS processes. No actual mining is done, as the true in-situ processes generate permeability in the highly

Jan 9, 1980

By T. Robyn

The Bolivar Cu-Zn skarn deposit in the Piedras Verdes mining district of Chihuahua is one of many base and precious metal deposits in the north-northwest trending Sierra Madre Belt extending across the states of Chihuahua, Durango and Sonora in northwestern Mexico. The information presented here is drawn from two papers on the Bolivar property1,4 plus new information. Historical mining and exploration for polymetallic Cu-Zn-Pb-Ag-Au deposits in the Sierra Madre Belt dates to Spanish Colonial days. Access to the Bolivar Property (Figure 1) is by paved road (approximately 305 km southwest from Chihuahua) and approximately 80 km by all-season gravel roads to the villages of Cieneguita (population ~1,000) and Piedras Verdes (population ~500) adjacent to the property. [ ] The Bolivar property comprises an old Cu-Zn producer (the Bolivar Mine), exploration concessions adjacent to the Bolivar Mine, and a new camp at the mine that supports mining, exploration and maintenance. From 1980 to 2000, former operators extracted approximately 300,000 tonnes of ore that was hand sorted to an average grade of 5-6% Cu and 25-30% Zn. From 2005-2010, Dia Bras produced from the mine just over 600,000 tonnes at an average grade of 1.7% Cu and 8.6% Zn. Dia Bras transported mineralized rock 275 km by truck and rail to its Malpaso mill, located about 30 km west of Cuauhtémoc in central Chihuahua, from 2005 until October 2011 when the new Piedras Verde mill was commissioned only 5 km from the mine. (Note: the Company cannot use the term ?ore? because it has never completed a feasibility study.)

Jan 1, 2012

By R. A. Jankowski

The U.S. Bureau of Mines (USBM) conducted a series of laboratory tests to investigate the effectiveness of using a flooded-bed scrubber with exhaust ventilation in deep-cut faces of up to 12.2 m in length. An experimental test program to determine the impact on respirable dust levels resulting from changes in face airflow, curtain setback distance, operator positioning, and operating parameters of the external spray system on the miner was completed. Gravimetric sampling was conducted in the immediate return and at three sampling locations on the off-curtain side of the entry. Statistically significant differences in dust levels on the order of 0.5 to 1.2 mg/m3 were observed between specific sampling locations and changes in several test parameters. Dust sampling results indicated that a flooded-bed scrubber and exhaust ventilation can be a viable dust control system for extracting deep cuts up to 12.2 m in length. The impact on methane was not evaluated.

Feb 24, 1997

By Carl Johnson, D. R. Todd

The Blue Ridge Low Level Outlet (LLO) was a design/build contract to provide a secondary means of discharging water from the Blue Ridge Reservoir. The project involved driving a 3.25 m (11 ft) modified horseshoe tunnel by 293.5 m (963 ft) long utilizing conventional drill and blast methodology. The intake shaft and structure were constructed inside of a sheet pile cofferdam surrounded by a maximum of 20.1 m (66 ft) of water. The shaft was excavated 4.87 m(16 ft) diameter to a depth of 12.8 m (42 ft) below the tremie slab elevation. Steel lining, including a transition from 3.66 m to 2.74 m (12 to 9 ft) diameter and a90 degree elbow were installed in the inlet shaft and then backfilled with concrete. This paper will describe the RFP phase, the design phase, challenges of the underground construction and contractual challenges.

Jan 1, 2005

By R. L. Guerguerian

Nowadays, most grinding mills driven by a wrap-around ring motor are operating successfully. Some of the earlier problems could be attributed to the lateral stiffness and stability of their bearings. As a result, modifications to the bearings included the rearrangement of the shoes, or the addition of more shoes, closer to the horizontal centerline. This technical paper reports a study of the effects of bearings on the lateral stiffness of grinding mills driven by a wrap-around ring motor. The discussions cover the design of the four shoe trunnion bearings and examine the effects of the angular location of the shoes.

Jan 1, 2000

By William R. Yernberg

SME’s Arizona Conference was held at the Doubletree Hotel at Reid Park in Tucson on Dec. 5and 6, 2004. The annual conference is organized by the Arizona Conference Board of Directors, which represents SME sections in Arizona and adjacent areas. The conference provides an opportunity for individuals and corporations associated with mining in the region to get together each year to discuss the status of the industry. The meeting featured a keynote address and more than30 technical papers. Two years ago, the U.S. copper industry was facing on a run for two years now,” and “both precious metal and base metal prices are going up.” The increases in metal prices were attributed to development in China and other Asian countries. “With a population of 1.6 billion, China has recently created 80 million jobs,” said Silver.

Jan 1, 2005

By W. S. Weldon, R. M. G. Machunter

The use of spiral separators for the beneficiation of fine coal typically in the size range - 2+0.lmm is now well established process technology. Developments during the mid 1980's resulted in the production of cost effective, efficient large diameter coal spiral separators. Recent developments and research have been geared to optimise metallurgical performance, materials handling and equipment geometry of large diameter coal spiral separators.

Feb 24, 1997

By G. S. Takenaka

When Bridger Coal Company transformed their operations from surface mining to an underground longwall operation their plans included not only the addition of new mining equipment but also surface fans for a blowing (supply) air ventilation system. The original system concept included a propane gas fired air heater to preheat the intake air during cold weather and a dual parallel fan and duct system. One fan operated to ventilate the mine while the other fan was for stand-by emergency operation. Equipment proposals were submitted in March, 2005 based on the dual parallel fan system. Discussions conducted during the equipment selection process revealed that several alternative system design concepts were available. The alternative concepts included innovation features that not only saved space and cost but also reduced operating expense as well. Many of the features were incorporated into the final design of the system. A comparison of the original system concept and final installation design are presented in the paper in addition to details of the features and the derived benefits.

Jan 1, 2009

By G. E. Jones, G. K. Hoffman

Through the USGS National Coal Availability pro-gram, two San Juan Basin studies have been completed. The study areas are in the northwest Bisti field, Fruitland Formation and in the eastern Standing Rock field, Menefee Formation. Original resources are 4.66 Gt and 3.46 Gt (5.14 billion stand 3.82 billion st), respectively, in the Bisti and Standing Rock areas. Bisti coal resources are greatly reduced by the Bisti-De-Na-Zin wilderness area (1.13 Gt (1.25 billion st)). Technological restrictions remove 31% from Standing Rock original resource. Available resources are 60% (2.79 Gt(3.07 billion st)) of the Bisti original resource and66% (2.26 Gt (2.49 billion st)) of the original Standing Rock resource.

Jan 1, 2000

By Charles Stone, Hannes Lagger, Dru Desai

The design methodology of the planned Second Avenue Subway Project (SAS) led to development of the initial support design to estimate cost and quantities in the Preliminary Engineering (PE) stage. Careful selection of the cavern design rules that recognized the impact of rock quality, rock cover, excavation geometry, and excavation sequence helped to overcome the design challenges of large, shallow caverns for the initial ground support. In the course of the design verification process prescribed by the design methodology, the design team was continuously reviewing and updating the support quantities. The design procedure includes methods using different approaches of empirical, continuum, and discontinuum analyses, which are currently advanced in the Final Engineering (FE) stage. The paper is a continuation of the RETC 2005 “Trials and Tribulations” and focuses on the procedures that led to the changes in the initial support as a result of the ongoing design development.

Jan 1, 2007

By J. E. Friant

Until 1956, drill and blast was the only way to excavate rock. In that year, a tunneling machine using disc type cutters economically bored a small Toronto tunnel. Its amazing 105 ft/day set a new world record and set the stage for a new industry. The Disc Cutter Role in Excavation Mechanical excavation of hard rock is by now deeply ensconced in the heavy civil construction industry. All over the world, from the Swiss Alp Melange to Hong Kong Granite, to New York Gneiss, huge Tunneling Boring Machines (TBMs) create transportation, water and sewer tunnels. Powerful machines, boasting as much as 6000 hp, bore through rock, excavating in excess of 1400 tons per hour. The tool that makes this tunneling phenomenon possible is the single blade, rolling disc cutter. These hardened steel discs, from 15 1/2 to 19 inches diameter are arranged on a rotating cutterhead, to cut concentric circles in the rock. As the machine is propelled forward under great pressure, rock below each cutter is crushed. But the efficiency of the cutterhead is derived from the science of cutter spacing (distance between cutter paths). The majority of the rock excavated is not crushed, but flakes off in chips and chunks. No pick, tooth, or drag type cutting tool can duplicate the performance of a disc cutter. The economic use of drag type tools is limited to as low as 5,000 psi UCS rock strength in massive formations. In weakly bonded, foliated rock, drag tools do better, but are still limited to rock generally less than 15,000 psi.

Jan 1, 2002