Search Documents

By B. P. Watson

The Bushveld platinum group metal deposits are two distinct, shallow-dipping stratiform tabular orebodies which strike for many hundreds of kilometres. Mining is extensive, with depths ranging from close-to-surface to 2 300 m. The mining method is a variation of planar open stoping. Pillars are widely employed to support the open stopes. In the deeper levels, in-stope pillars are required to fail in a stable manner soon after being cut, and the residual pillar strength is used to stabilize the hanging wall. These pillars are commonly known as crush pillars. Little work has been done in the past to determine pillar peak and residual strengths, and pillars have been designed using experience and formulae developed for other hard-rock mines. This has led to over and undersize pillars with consequential loss of ore, pillar bursts and potential collapses. This paper describes a crush pillar design methodology, and provides design charts. Three mining environments were incorporated in the investigations, which included underground and laboratory measurements, analytical solutions, numerical model sand back analyses. The results of the study are suitable for the areas where the research was carried out, and may also be applied with caution in other similar environments.

Jan 1, 2010

By N. Kumar, A. K. Dhawan, A. Varughese, S. K. Khullar

Abstract The in-situ stress field is one of the primary parameters influencing the performance of underground structures particularly in the Himalayas where there is strong influence of topography and geology on in-situ stresses. It is always advisable to measure the in-situ stresses, in whatever best way possible. Hydrofracturing is one of the methods by which in-situ stress can be measured. This paper briefly describes details of the concept of Hydrofracturing in arriving at the in-situ stresses of the rock mass at Pancheswar Project. The data obtained from the tests has been analysed, interpreted and the results are presented in this paper. Kurzfassung Das Spannungsfeld an Ort und Stelle ist einer der wichtigsten Parameter, die das Verhalten der Untergrund-Struktur beeinflussen, insbesondere in den Himalayas, wo die Topografie und die Geologie einen grossen Einfluss auf die oertlichen Spannungen ausueben. Es empfiehlt sich stets die Spannungen an Ort und Stelle so gut wie moeglich zu erfassen. Die Hydrofraktur bzw hydrografisches Zerstueckeln ist eine der Methoden, die bei den Messungen der oertlichen Spannungen verwendet werden koennen. Diese Abhandlung beschreibt kurz Einzelheiten ueber das Konzept von Hydrofraktur bei der Bestimmung der Spannungen an Ort und Stelle von der Felsmasse bezueglich des Projekts Pancheshwar. Die gewonnenen Daten aus den Messungen wurden analysieret und ausgewertet. Die Ergebnisse werden dabei vorgelegt. Sommaire Le champ de contraintes in-situ est un des paramèters principaux influencant l’exécution des structures souterraines particulierèment en Himalaya où les forces in-situ sont fortement influencées par les caractéristiques topographiques et géologiques de la région. La fracturation hydraulique est une technique qui permet de mesurer des forces in-situ des massifs rocheux. Cet article décrit brièvement le mécanisme de fracturation hydraulique et présente les résultats de mesure des forces in-situ des roches au site du projet hydroélectrique de Pancheswar.

Jan 1, 2003

Experimental results are presented that test the hypothesis that the descaling behaviour of stainless steel slabs following reheating is controlled by interfacial roughening at the scale-steel interface. In this investigation, two stainless steels were considered: type 304 (austenitic, with 18% Cr and 8% Ni) and type 412 (ferritic/martensitic, with 11.6% Cr). It was found that the entanglement that arises at the scale-steel interface was in fact effective in maintaining scale-steel adhesion, under the mechanical descaling conditions used. In the case of type 304, descaling proceeded by fracture along chromite layers, which formed (by internal oxidation) on the austenite grain boundaries; for this steel, the extent of descaling depends most strongly on austenite grain structure, and not primarily on the conditions in the reheating furnace. In contrast, type 412 samples descaled only at the edge of the entangled zone, and showed a greater sensitivity to the reheating conditions; specifically, higher free oxygen in the reheating gas and longer reheating times were found to increase the residual scale thickness. Key words: stainless steel, reheating, scale, entanglement, descaling, fayalite, internal oxidation, grain structure, free oxygen.

Jan 1, 2003

By C. Kruger

Anglo American Platinum has adopted a strategy of best practice principles (BPP) for sampling, mass measurement, analysis, and metal accounting for more than a decade now. When new plants are designed, the most suitable sampling equipment and sampling protocols are implemented and material flows and plant layouts are designed around sampling strategies. A few years ago, a crushing plant for a high-grade matte stream was commissioned. The design called for the high-grade material to be crushed to 95% passing 2 mm, and the design allowed for a single-cutter primary Vezin sampler taking increments from a gravity flowing stream at regular intervals while filling a tanker for pneumatic offload at the base metal refinery. This was a single point of sampling and analysis that would measure the wanted output from the smelting complex and the input to the refineries. In addition, the design incorporated the functionality to collect increments in an ?interleaved? fashion from the Vezin sampler for internal precision checks. The metal accounting strategy for Anglo Platinum involves the ongoing measurement of all inputs, outputs, and stock levels for all operations for platinum group metal (PGM) and base metal (BM) content. Included are yearly stocktakes, usually done on 1 February, across the smelters and refineries (at least the base metal refinery). In the accounting period immediately following the introduction of the new crushing and sampling facility, a trend was developing whereby the absolute difference between the physical stock and theoretical stock (PGMs predominantly) increased for the two respective sites on an ongoing basis. The smelter showed an increase in physical stock compared to the theoretical stock (sender) and the base metal refinery showed an increase in theoretical stock against physical stock. Because of this anomaly, an additional stocktake was held in September for the period in question, and it was confirmed through the physical stock measurement results that the PGM accounting problem was indeed pointing towards the evaluation of the high-grade matte stream. This paper showcases parts of the process that took place to explain the poor accountabilities for the two sites. Previous results from the sampler ratification process (of the interleaved sampling design) were reanalysed, a physical inspection was carried out on the sampling system again, and the sampler performance was monitored (quality control parameters) for the period. From these investigations, it was found that airflows inside the Vezin introduced the sampling bias. A change in sampling protocol was introduced, as well as certain physical changes to the sampling equipment, to eliminate the airflow and thus the bias conditions significantly. The accounting period that followed the phased upgrading process showed that the accounting between the smelter and base metal refinery had been restored to within statistical limits (difference between physical and theoretical stock below 5% relative to theoretical stock). Keywords sampling, metal accounting, Vezin sampler, sampler bias.

Jan 1, 2014

By J. D. Steenkamp, G. E. Williams

Keywords: Ilmenite, titania slag, pig iron, rutile, zircon Located on the eastern shores of South Africa, 180 km north of Durban, Richards Bay Minerals (RBM) produces approximately 2.0 million metric tonnes of product annually making RBM a leading producer of titania slag, high purity pig iron, rutile and zircon. Heavy minerals are extracted from the nearby dunes by dredging and concentration on a floating gravity separation plant, followed by separation of the ilmenite, rutile and zircon at the mineral separation plant located at the smelter site. The ilmenite is processed through an oxidizing roast followed by magnetic separation and is then partially reduced to an 85 per cent TiO2 slag in one of four six-in-line a.c. electric arc furnaces. The slag is milled and then classified into two product sizes suitable as a raw material for both the sulphate and chloride pigment processes. The high quality iron produced during the reduction process is further processed to produce various grades of low-manganese iron. Around 95 per cent of the products are exported, yielding a world market share of about 25 per cent of titania slag, rutile, high quality pig iron, and zircon.

Jan 1, 2006

By S. Z. Pethö, H. Yilmaz

South Deep Mine is currently undertaking numerous voidfilling projects using low strength aerated cement products. Representative samples from one such site, were taken and tested for the load deformation behaviour under uniaxial loading conditions. The process of sample collection, laboratory preparation and testing are explained in detail. The results of testing were analyzed and the critical aspects pointed out as a design consideration to be implemented as part of the quality control and assurance program. Design aspects and underground application of the aerated cement product are discussed for the particular site on 58 level SV1. A simple instrumentation has been designed and installed to enable monitoring of any future movements in this area. A quality control and assurance process has been formulated enabling all aspects of the support installation in this excavation to be signed off.

Jan 1, 2003

By S. K. Murphy, S. M. Spottiswoode, A. M. Milev, D. Geyser

A portable, stand-alone instrument especially designed for recording strong ground motion was used in this study to create a large database of peak particle velocities measured underground. A total number of 39 sites located in stopes mining Carbon Leader and Ventersdorp Contact Reefs were investigated. Peak particle velocities whith values up to 3 m/s were recorded at some sites. The data recorded on the skin of the excavations were compared to the data recorded by the mine seismic networks to determine the site response. The maximum site response was obtained for source radii of between 5 m and 30 m and events locating within 200 m of the site. The extreme values of peak particle velocities were obtained in cases were the face-area lay within the source radius. Un instrument portable unique spécifiquement conçu pour enregistrer les mouvements dynamiques des terrains, a été utilisé dans cette étude pour créer une base de données importante sur la vélocité maximum des particules, mesurée en souterrain. Un nombre total de 39 sites situés dans les excavations exploitant les récifs appelés ‘Carbon Leader et Ventersdorp Contact Reefs’, a été investigué. Une vélocité maximale avec des valeurs allant jusqu’ à 3 m/s a été enregistrée sur certains sites. Les données enregistrées sur le bord de l’excavation ont été comparées aux données enregistrées par les réseaux séismiques de la mine pour déterminer la réponse du site. La réponse maximum du site a été obtenue pour des sources de rayons entre 5 m et 30 m et des évènements situés dans les 200 m du site. Les valeurs extrêmes de vélocités maximales ont été obtenues pour les cas où la zone de face se trouve à l’intérieur du rayon de la source. Ein mobiles, alleinstehendes Instrument, speziell entworfen um starke Formationsbewegungen aufzuzeichnen, wurde in dieser Studie verwendet um eine große Datenbank von Partikelspitzengeschwindigkeiten, die Untertage gemessen wurden, aufzuzeichnen. Eine Gesamtanzahl von 39 Aufstellungsorten in den Schichtabbauorten vom Carbon Leader und Ventersdorp Contact Reef wurden untersucht. Partikelspitzengeschwindigkeiten mit Werten bis zu 3 m/s wurden an einigen Standorten aufgezeichnet Die an der Oberfläche des Grubenraumes aufgezeichneten Daten wurden mit jenen Daten verglichen, die vom seismischen Netzwerk der Grube notiert wurden, um die örtliche Reaktion des Standortes zu bestimmen. Die maximale Standortreaktion wurde für Ursprungsradien von zwischen 5 m und 30 m erhalten und Ereignissen die sich innerhalb von 200 m vom Standort befanden. Die extremen Werte der Partikelhöchstgeschwindigkeiten wurdenin jenen Fällen erreicht wo sich der Abbaubereich innerhalb des Ursprungsradiuses befand.

Jan 1, 2003

By J. van der Merwe, D. Tharandt

The corrosion behaviour of 304L stainless steel laser-cladded with various amounts of ruthenium (Ru) was evaluated in solutions of sulphuric acid and sulphuric acid plus sodium chloride at 25°C and 45°C by open-circuit potential and cyclic potentiodynamic polarization tests. In general, the addition of Ru to the stainless steel increased its corrosion resistance in 1 M H2SO4, as well as in 1 M H2SO4 plus 1 wt% NaCl. This was observed for a number of parameters such as corrosion rate, corrosion potential, open-circuit potential, and current density. However, increasing the amount of Ru added beyond a certain level did not result in further improvement in corrosion protection. For each environment there is an optimal Ru concentration for the best corrosion protection. For example, in 1 M H2SO4 at 25°C, 2.44 wt% Ru shows the least active surface in terms of corrosion. Further research into ruthenium coatings on stainless steels is recommended.

Jan 1, 2015

By J. A. Cruise

With the end of the official apartheid legislation in the early 1990s, South Africa was heralded as a non-racial country. However, racial awareness has been reintroduced into the country with the Affirmative Action and Black Economic Empowerment legislation. Gender and racial transformation are the current order of the day. All organizations are required to reflect in their make-up the demographics of the population as soon as possible. Scorecard shave been drawn up to measure the rate of transformation for gender and race in organizations. The mining industry in South Africa has been in the forefront of this transformation legislation and scorecards. This paper seeks to show the effect of gender and racial transformation on mining engineering education and professionalism by analysing the changing demographics of graduating mining students at both the South African universities offering a degree in mining engineering, the professional registration of mining engineers with the Engineering Council of South Africa (ECSA), and the membership of the Southern African Institute of Mining and Metallurgy (SAIMM), the vocational institute for mining engineers. It also demonstrates the absurdity of gender and racial quotas based solely on the demographics of the current population of the country. This paper shows the degree to which mining engineering has transformed in both gender and race.

Jan 1, 2011

By Henri Fredriksson, Rami Saario, Mark Weatherseed, Juri Matinheikki

"The challenges facing the mining industry include complex ores and declining grades, together with increasing capital costs and environmental regulations. In addition, future commodity price uncertainty makes investment decisions difficult. Shorter plant lifecycles mean that new projects need shorter payback and increased net present value. With regard to solvent extraction, the introduction of an innovative modular plant design will help to address these issues. The first such modular offering is Outotec’s VSF®X modular solvent-extraction plant that uses prefabricated and transportable modules. Reuse and recyclability have underpinned the design concept. The greatest advantage of the VSF®X modular solvent-extraction plant is its relocation possibility. Additionally, it is suitable for various metals and plant capacity is adjustable through a scalable modular structure. After a dedicated plant lifecycle, the plant can be dismantled and relocated to a new site. This reuse ability offers major benefits for short-term plants, making them more feasible due to higher residual value. A net present value analysis is made for two examples, a conventional plant with no relocation possibility and a modular movable plant with extended plant life cycle, in order to evaluate the feasibility of modular plants. Results indicate that modular plant design could offer an economical solution with the additional advantage of improved overall sustainability through its life cycle. INTRODUCTION The challenges facing the mining industry include complex ores and declining grades, together with increasing capital costs and environmental regulations. In addition, future commodity price uncertainty makes investment decisions difficult. Shorter plant lifecycles mean that new projects need shorter payback and increased net present value (NPV) (Mudd, 2010; Norgate & Jahanshahi, 2010) . Awareness of sustainability issues is also rising and sustainability reporting is now a key element of many companies’ public and investor relations. Major companies are now putting more effort in this area to earn legitimacy for new projects (Mudd 2010)."

Jan 1, 2015

By F. H. Cornet, D. Ask, O. Stephansson

We have conducted a stress analysis of overcoring stress measurements undertaken at the Zedex Test Site (ZTS) in the Äspö HRL, Sweden. Two different types of overcoring cells have been used at the site: the 9-gauge Borre Probe (CSIR-type) and the 12-gauge CSIRO HI cell. Inversion programs based on the least-squares criterion were developed and calibrated. The primary and secondary stress field in the ZTS were back-calculated using strain data from individual cells as well as from combining data from both cells. We propose that the combination of strain data from the two cells significantly improves the determination of the stress field. A striking result is the good agreement between the re-analysed overcoring data and the existing hydraulic fracturing data. The deviations for the horizontal stresses between the re-analyzed overcoring data and the existing hydraulic fracturing data are approximately 3 MPa. The deviation in the orientation of maximum horizontal stress is approximately 10-20°. Nous avons analysé les résultats de mesures de contrainte par surcarottage réalisées sur le site Zedex, du laboratoire souterrain HRL d’Aspö, en suède. Deux types de cellule de mesure ont été utilisés sur ce site : la cellule à 9 jauges (du type CSIR) et la cellule à 12 jauges (du type CSIRO HI). Un programme d’inversion mettant en œuvre une norme par moindres carrés a été développé et validé. Les champs de contrainte primaires et secondaires du site Zedex ont été évalués d’une part en considérant chaque mesure isolément, d’autre part en intégrant l’ensemble des données de déformation dans une inversion unique. Nos résultats suggèrent que l‘association des diverses mesures dans une intégration unique améliore nettement la détermination du champ de contrainte. Un résultat intéressant est le bon accord entre ces nouveaux résultats et les résultats des mesures par fracturation hydraulique. Les écarts sur l’amplitude des contraintes horizontales est de l’ordre de 3 Mpa, les écarts sur les orientations de l’ordre de 10-20°. Auf dem Zedex Test Gelände im Äspö Festgesteinslabor (HRL) wurde eine Spannungsanalyse mittels Overcoring Spannungsmessungen durchgeführt. Hierzu wurden zwei verschiedene Methoden verwendet: das 9-kanal Borre Gerät (CSIR- Ausführung) und die 12-Kanal CSIRO HI Zelle. Inversionsprogramme, die auf dem “least-squares”- Kriterium basieren, wurden entwickelt und kalibriert. Das primäre und sekundäre Spannungsfeld des Zedex Test Geländes wurde sowohl aus Verformungsdaten individueller Zellen als auch aus Kombination beider Zellen ermittelt. Wir nehmen an, daß die Kombination der Messergebnisse beider Geräte die Bestimmung des Spannungsfeldes signifikant verbessert. Überzeugender Beweis hierfür ist die gute Übereinstimmung der überprüften Overcoring Daten und Ergebnisse aus existierenden Hydraulic Fracturing Versuchen. Die Abweichungen der horizontalen Spannungen aus beiden Datensätzen ist etwa 3 MPa und Abweichungen der Orientierung der größten Horizontalspannung liegen bei etwa 10-20°.

Jan 1, 2003

By D. L. H. Bulbring

The removal of a cylindrical core from thick-wall sections for creep analysis by the relatively new Weldcore® process represents a very exciting methodology for obtaining more representative creep damage data from large engineering structures. The cylindrical core that is removed, representing about 60% of the wall thickness, leaves a substantial removal site that needs to be repaired. This paper presents data pertaining to taper Friction Hydro Pillar Processing as an alternative repair technique for filling the core removal site. Process parameters were evaluated with special attention being paid to the effect of downward force on process response variables, weld defects, and mechanical properties of 10CrMo910 steel. Process temperature and torque response as well as total process energy input were also considered. This paper also assesses the static and dynamic performance of this repair technique. The influence of a varying downward force and the occurrence and position of discontinuities were quantified. Downward force was shown to have the most notable effect on weld joint dynamic performance and was found to be related to the process temperatures achieved in close proximity to the weld interface.

Jan 1, 2013

By K. S. Liddell

The Kell Process has been developed for the extraction of platinum group metals (PGMs) and base metals from sulphide flotation concentrates. The process has been successfully tested on several different sulphide flotation concentrates, including those from the UG2 chromitite horizon and the Platreef mafic/ultramafic layer. It has been shown to provide high (>95 per cent) and selective extraction efficiencies for the key valuable metals, i.e. Pt, Pd, Rh, Au, Ni, Co, and Cu. The Kell Process consists of several commercially proven unit operations. S, Ni, Co, and Cu are first selectively removed by use of a pressure oxidation step during which the dissolution of PGMs is minimized. The residue from pressure oxidation is subjected to a thermal treatment to ensure efficient PGM recovery by subsequent chlorination. All the core steps are very similar to well-proven conventional unit operations in common use, as are the subsequent metal recovery steps to provide marketable end products. Typical metallurgical responses of flotation concentrates from UG2 and Platreef to the Kell Process are provided, and key outcomes of an energy comparison study with smelting are summarized in this paper. Kell presents a potentially substantial improvement in PGM concentrate processing technology, in terms of economics via much-reduced power costs, ease of processing, and various environmental benefits. It allows for the treatment of high-chromium low-grade 'dirty' concentrates, such as secondary concentrates from the platinum industry's 'mill-float-mill-float' (MF2) flotation circuits and concentrates from retreatment of tailings. It allows greater concentrate mass pulls, has higher tolerance to gangue intergrowths in concentrates, and its use can provide substantial increases in overall PGM recovery. Its adoption would be a step change in the platinum industry, and given the commercially proven unit operations embodied in the Kell Process, at much-reduced risk compared with other more experimental technologies. Since the initial process development work, significant improvements and refinements have been introduced as a result of further compre¬hensive testing and process modelling. Pilot-scale testing and engineering study work is in progress for several selected sites.

Jan 1, 2012

By Y. Guglielmi, V. Merrien-Soukatchoff, I. Kadiri

ABSTRACT: Hydraulic experiments have been conducted since 1997 within a small fractured calcareous rock mass in southeastern France, at a site called Coaraze. On this reduced-scale site closing a floodgate located on a downstream spring produces repeated hydraulic loadings. Simultaneous measurements of normal deformations and pressure in several joints have provided a better understanding of the hydromechanical behaviour of such a fractured rock mass. The present paper first describes both the site and conceptual interpretation of the measurements performed. We showed that accurate measurement reproduction requires incorporating certain features: a variable normal joint stiffness, the joint vicinity (through introducing a Z coefficient), and the initial stress state. The paper then develops an original analytical interpretation of the coupled pressure-displacement measurements carried out, which reveal the high level of measurement suitability to the non-linear behaviours examined. 2D modelling, using the discontinuous code (UDEC) was used to proceed with the calibration step. KEY WORDS: In situ test, methodology, hydromechanics, modelling, non linear behaviour ZUSAMMENFASSUNG : Hydromechanische Experimente werden seit 1997 in einer kleinen Kalksteinmasse, das sich im Südosten von Frankreich befindet durchgeführt. In diesem kleinen Standort, werden wiederholte Wasserdruck Erhöhungen durch das Schliessen eines Hahnes produziert. Gleichzeitiger Druck und normale Verformung Meßungen in mehreren Fugen haben erlaubt, das hydromechanische Verhalten einer solche gebrochene Felsenmasse besser zu verstehen. Der Artikel beschreibt zuerst den Standort und stellt die begrifflichen Interpretationen der Meßungen vor. Um die Meßungen gut zu reproduzieren ist es wesentlich, bestimmte Faktoren wie die veränderliche normale Steifheit der Fugen, die Nachbarschaft der Fugen (über einen Z-Koeffizient) und der Spannungstand zu berücksichtigen. Der Artikel erklärt die originale Methode für die Druck- und Verformungs-Meßungen Interpretation und zeigt die gute Korrelation der Meßungen mit dem nicht-linearen angenommen Verhaltens der Fugen. Die numerische 2D-Modellierung mit dem UDEC Software ist für die Verkeilung der Faktoren gebraucht worden. SCHLÜSSELWÖRTER: In-situ-test, Methodologie, Hydromechanik, Numerische Modellierung, nicht-lineares Verhalten RESUME : Des expérimentations hydromécaniques sont conduites depuis 1997 dans un petit massif calcaire fracturé situé dans le sud de la France. Dans ce site de taille réduite des mises en charge répétées sont produites par la fermeture d'une vanne située à l'aval du site. Des mesures simultanées de déformation normale et de pression dans plusieurs joints ont permis de mieux appréhender le comportement d'un tel massif fracturé. L'article décrit dans un premier temps le site et présente les interprétations conceptuelles des mesures. Pour bien reproduire les mesures, Il est essentiel de prendre en compte certains facteurs tels que la raideur normale variable du joint, le voisinage du joint (par l'intermédiaire d'un coefficient Z), l'état de contrainte initial. L'article précise la méthode originale d'interprétation des mesures pression-déplacements qui montre la bonne adéquation aux lois de comportement non linéaire proposées. La modélisation 2D, à l'aide d'un code discontinu (UDEC) a été employée pour le calage des facteurs. MOTS-CLEFS : In-situ, méthodologie, hydromécanique, modélisation, comportement non linéaire

Jan 1, 2003

By Y. Mitani, M. Xie, G. Zhou, T. Esaki

The assessment of landslide instability and risk has become a topic of major interest for both geoscientists and engineering professionals as well as for local communities and administrations in many parts of the world. In this paper, based on a new developed Geographic Information Systems (GIS) grid-based 3D deterministic model and taken the slope unit as the study object, the landslide hazard is mapped by the index of the 3D safety factor. Assuming the initial slip as the lower part of an ellipsoid, the 3D critical slip surface in the 3D slope stability analysis is obtained by means of a minimization of the 3D safety factor using the Monte Carlo random simulation. The failure probability of the landslide is calculated by an approximate method in which the distributions of f,c and the 3D safety factor are assumed to be in normal distributions. The assessment of the earthquake triggered landslide hazard is done by the dynamic displacement analysis using the index of the Newmark displacement. All the calculations are implemented by a computational system call 3DSLOPEGIS in that a GIS component is used for fulfilling the GIS spatial analysis function. Besides the results of 3D safety factor and probability, the possible landslide body and boundary can be three-dimensionally quantitatively identified. L’ estimation des glissement de terrain et des risques impliqués est devenu un des principal sujet de préoccupation pour les géotechniciens, mais aussi pour les ingénieurs specialisés ainsi que pour les communautés et administrations locales dans de nombreuses région du monde. Dans cette étude, basé sur un modèle de maillage 3D et une approche déterniniste couplée au Système d'Information Géographique (SIG), étudiant la stabilité des versants , le lieu d'étude à risque est maillé suivant le facteur de sécurité calculé en 3D. En supposant que le glissement initial soit la partie inférieure d'un élipsoïde, l'analyse de stabilité pour le glissement critique 3D d'un versant 3D est obtenu grace à une minimisation du facteur de sécurité en 3D utilisant la méthode de simulation aléatoire de Monte Carlo. La probabilité d'un glissement de terrain est calculée par une méthode approximative, supposant la distribution de c, f et du facteur de sécurité 3D normale. L'estimation d'un risque de glissement de terrain causé par un tremblement de terre est faite grace à une analyse du déplacement dynamique suivant l'index de Newmark. Tous les calculs sont effectués par le biais d'un système de calcul appellé 3DSLOPEGIS dans lequel te GIS est utilisé pour gérer l'analyse spatiale. En plus de cela, les résultats du coefficient de sécurité en 3D, des probabilités, le terrain susceptible de glisser, et ses limites, peuvent être quantitativement évalués en trois dimensions. Die Bewertung von Erdrutsch-Instabilität und risiko sind zu einem Thema von großen Interesse für sowohl Geowissenschaftlern und Ingenieuren als auch von Gemeinden und Verwaltungen in vielen Teilen der Welt geworden. In dieser Arbeit, basierend auf einem neu entwickelten Geografische Informationssysteme (GIS) gitterbasierten 3D deterministischen Modell und mit der Böschung als Untersuchungsobjekt wird die Erdrutschgefahr durch den Index des 3D-Sicherheitsfaktors kartografiert. Unter der Annahme, dass der erste Rutsch der untere Teil eines Ellipsoiden ist, wird die 3D kritische Schlupfoberfläche in der 3D-Böschungsstabilitätsanalyse mit einer Minimierung des 3D-Sicherheitsfaktors mit der Monte Carlo Zufallssimulation erhalten. Die Fehlerwahrscheinlichkeit des Erdrutschs wird mit einer Annäherungsmethode berechnet, bei der die Verteilungen von f,c und dem 3D-Sicherheitsfaktor als innerhalb normaler Verteilungen angenommen werden. Die Beurteilung der Erdbeben-ausgelösten Erdrutschgefahr wird mit der dynamischen Verdrängungsanalyse mit dem Index der Newmark-Verdrängung gearbeitet. Alle Berechnungen werden mit einem Berechnungssystem mit der Bezeichnung 3DSLOPEGIS ausgeführt, bei dem eine GIS-Komponente zum Erfüllen der GIS räumlichen Analysefunktion verwendet wird. Neben der Ergebnissen des 3D-Sicherheitsfaktors und der Wahrscheinlichkeit kann der mögliche Erdrutschkörper und der Umfang dreidimensional quantitativ identifiziert werden.

Jan 1, 2003

A wide range of drill holes and process streams are sampled for resource estimation, grade control, and contractual purposes in the minerals industry. However, despite the availability of training courses, conferences and both national and international standards on correct sampling practices, it is still surprising how often little attention is given to ensuring that representative samples are collected for analysis. The reason for this is that the responsibility for sampling is often entrusted to personnel who do not appreciate the significance and importance of sampling, with cost being the main driving force rather than whether the sample is representative of the material from which it was extracted. This seriously undermines the precision and accuracy of the analyses subsequently generated and can render the analysis process a total waste of time and money and expose mining companies to serious, potential, financial losses. Company management needs to reverse this situation and ensure that sampling is given the attention it deserves to generate representative samples for analysis.

Jan 1, 2010

By L. A. Thompson, A. J. Linington

"Copper–cobalt extraction is a reagent-intensive process resulting in acid consumption greatly contributing towards production costs, which in the current market conditions curtail profitability. Nanofiltration (NF) membranes have become an attractive approach in the mining and minerals industry for product concentration and reagent recovery based on the ability of the membrane to separate monovalent ions from divalent ions. NF membranes can selectively separate acids from metals and salts allowing acid to be recycled as well as the concentration and purification of product streams. Membrane technology in the field of copper–cobalt processing focusses on the concentration of Cu2+ and Co2+ in the pregnant leach solution, recovery of acid from waste streams to neutralization, recovery of valuable metals from waste ponds and process water recovery. This paper aims to provide insight into the potential applications of NF membranes in copper–cobalt processing circuits as well as a brief overview of the effects of process conditions on membrane performance and process development. INTRODUCTION The copper–cobalt industry commonly uses inorganic acids, such as sulfuric acid, in large quantities for primary leaching of copper–cobalt oxide ores and releaching during product purification (Stuurman et al., 2014). This results in numerous acidic intermediate streams containing high metal concentrations and acidic waste streams with low metal concentrations. Acid consumption typically accounts for 10–15% of the operating costs of mines in the Democratic Republic of Congo (DRC) and Zambia (Acid Plant Database, 2015). Due to remote mine locations, poorly maintained roads and cross-border conflict, the cost of sulphuric acid can range between USD 300 and 400 per ton. The pivotal role of acid in the copper–cobalt extraction process has driven many mines to build sulphuric acid plants on site to ensure a reliable acid supply, however elemental sulphur still needs to be imported which faces similar logistical challenges and contributes towards operating costs."

Jan 1, 2015

By Ernie Holden, Chris Ringas

In the last 20 years, In Line Inspection (ILI) using intelligent pigs has become the principal tool used by pipeline operators to assess the condition of their pipelines. New pipelines are normally designed to take intelligent pigs, but many older pipelines require some modifications and special procedures for their inspection. This paper is aimed at practicing engineers and managers of pipelines, or people aspiring to those positions. The paper describes the benefits of ILI and some of the practical issues regarding pipeline preparation and cleaning, choice of inspection tool, running pigs in pipelines, and what to do with the data collected. What are the responsibilities of the Pipeline Engineer ? ? Maintain reliable and acceptable performance of the pipeline in terms of safety and product delivery at economical cost. ? Provide a defined margin of safety for operating the pipeline at its designated pressure. ? Provide timely information on all pipeline defects such that repairs can be carried out according to a managed schedule. What Defects does the Pipeline Operator have to cope with ? A useful record of actual incidents seen in pipelines can be obtained from the web site of the US Office of Pipeline Safety (OPS) - http://ops.dot.gov/stats/stats.htm. US pipeline Operators are obliged by Law to report all pipeline incidents exceeding certain threshold criteria (e.g loss of life, escape of product, cost of incident etc). These OPS statistics show that corrosion and third party damage have remained consistently the prime causes of reportable incidents in the US, with similar experience elsewhere. There are several kinds of flaws and defects in pipelines that can lead to failure, the main families being :- ? Metal loss ? Cracks or crack-like defects ? Laminations and other mid-wall defects ? Geometric anomalies

Jan 1, 2006

Mr G H Park was born and brought up in Zimbabwe, in mining from the University of the Witwatersrand. Starting as a Learner Official at Rand Mines, he went Mr D J van Niekerk was educated at Helpmekaar Boys' High School in Johannesburg and the University of Pretoria. Mr C J C Janse van Vuuren was educated at Klerksdorp High School, Pretoria Technical Colege, the University of Pretoria, and Unisa. He holds the folowing degrees: BSc (I&S), BSc Hons (Met Pta), ND (Met Tech), AEP (Unisa). Prof. R F Sandenbergh was educated at the Afrikaanse Hoerskool Germiston and the University of Pretoria. He holds the degrees of B Ing (Chem), M Ing (Chem), and D Ing (Metal). President's Award Professor Jannie van Deventer, Head of the Department of Metalurgical Engineering at the University of Stelenbosch, has been honoured with one of the five President's Awards for 1990. These awards are made by the CSIR's Foundation for Research Development. G R Bozzoli Awards* Prof. Alan Kemp, Dean of the Faculty of Engineering at the University of the Witwatersrand, has appealed to industry not to cut bursary funding during recessionary times.

Jan 1, 1990

By W. de Beer

We present aspects of one of several ongoing case studies used in the development of prediction techniques for major seismic instabilities. The current investigation centres on accelerated coseismic deformation described by the kinematics of failure and on softening, as well as the characterization of areas of interest by measures of the seismic response at such sites.

Jan 1, 1998