Search Documents

By A. A. Hazell

Mine management by objectives by A. A. Hazel Published in the Journal, September 1972 DISCUSSION H. H. McGREGOR Mr Hazell is to be complimented on a thoroughly down to earth analysis of the uses ot which work study can be put and the benefits of properly applying it in the management of underground production.

Jan 9, 2007

By F. R. Deist, R. P. Plewman

Discussion: A. Hazell (Associate Member) and T. J. Kotze (Graduate Member): The authors must be congratulated on the development of a versatile computer programme for determining the stresses and displacements resulting from mining operations. As a design tool it will no doubt take its rightful place together with the analogue computer. Union Corporation made use of this digital computer programme whilst still in its development stage to determine the stress distributions which were causing the unexpected failure of the Marievale sub-incline shaft. Two features arising from this investigation may be of interest to members, namely: A. The solution to the problem of stabilizing a rectangular inclined shaft, which turned out to be contrary to accepted mining practice, and B. A comparison between the results obtained with the pure digital system and the analogue computer. A. The shaft is nine ft high and 20 ft wide, dipping at 9° to the horizontal and crossing the bedding planes. Fig. 1 is a plan and Fig. 2 is a section of the sub-incline shaft pillar area showing the relative positions of the shaft and reef as well as their respective dips. The deepest point in the shaft is 3 300 ft below surface and the requirement of a stress free ground surface may not be satisfied. It also means that the original gravitational stresses are low. A 900 ft wide pillar was left to protect the bottom section of the shaft, the top section being understoped years ago. Extraction of the pillar was started at the beginning of last year, mining operations being carried out in the accepted manner, starting beneath the shaft and mining outwards. The approach did, however, turn out to be the wrong one, because failure of the shaft was noticed soon afterwards. Even small movements were serious in this case due to the low clearance between the skips and the shaft supports. During October, 1968, failure between benchmarks 8 and 10 (see Fig. 1) became so excessive that hoisting speeds had to be reduced. Failure continued to occur and, by the end of March, 1969, failure had propagated up the shaft as far as benchmark 7, and down as far as benchmark 12. As this shaft had a tight hoisting schedule it was imperative that a quick solution be found to arrest the failure.

By T. K. Roy

INFACON XI has no doubt earned the distinction as the first such Congress in India. This prestigious occasion could become a reality of a long cherished dream of the Indian Ferroalloy Producers, consumers and ex-porters. The International Committee of Ferro Alloys (ICFA), South Africa, the august body for organising INFACON, every three years, could be convinced by the Indian Ferro Alloy Producers? Association (IFAPA) to award INFACON (XI) to India. This Congresss, organized by IFAPA, has opened a window for the Ferroalloy Community of India, the up-coming Asian Tiger, to register their strength and weakness to the world forum with the principal objectives of evolving long and short-term optimum road-maps for development. It is to be reckoned that India is poised to be a steel giant by 2020 when it is envisaged that the steel production may reach a level of 120 million tons of which significant proportion has to be in the categories of alloy and special steels, requiring standard and high grade ferroalloys. Keeping the above objective in view, the theme of this Congress has been rightfully designed as ?Innovations in Ferro Alloy Industry.? This Congress has also earned a distinction of more than eighty papers, finally selected for inclusion in the Proceedings. More than 100 internationally and nationally reputed experts in the field of ferroalloys (technology and manufacturing practices as well as world scenario) have been approached for critical review of abstracts and selection for the proceedings. It needs to be mentioned without the cooperation received from ICFA the high standard of INFACON could not have been assured. The papers are suitably grouped under seventeen heads, starting from world situation to production and operation followed by present and future technologies and finally to modelling and simulation. It is a Herculean task to the Technical Committee to fit these papers in proper sequence. The Commit-tee members kept no stone unturned to ensure the cogency with the subject matters and at the same timekeeping the flexibility of interests of the participant, especially in the context of three parallel sessions. The Proceedings containing only refereed papers of high quality, will serve the entire gamut of ferroalloy industry and will also highlight the present status of concerned countries. The areas of attention to make the industries globally competitive and at the same time laying emphasis on the prevailing practices, will help the industry leaders to formulate an appropriate global approach. Following the break-through step, instilled by INFACON XI, the Proceedings will be available both in bound and in searchable electronic CD-ROM format. I, as the Chairman of the Technical Committee would like to express thanks and high appreciation to all the Committee members for their whole hearted efforts in all respects without which it would not have been possible to complete these proceedings in the scheduled time. Technical Committee desires to place on record their gratitude to Organising Committee for their synergic cooperation all through in successfully executing multifarious tasks, associated with such a grand international technical Congress.

Jan 1, 2007

By P. E. Venteer

The Grootegeluk coal-processing plant treats 3 kt of raw coal per hour to produce a middlings fuel coal and a coking coal fraction with ash contents of 35 and 10 per cent respectively. The plus 0,5 mm fraction is treated by heavy-medium processes, the final top size of the coal being 15 mm. About 400 t of minus 0,5 mm coal per hour is subjected to froth flotation. The routes originally considered for the processing of this fine coal were froth flotation, shaking tables, heavy-medium cyclones, and water only cyclones in combination with froth flotation. The results from tests on the fines arising from a small-trial open-cast mine are discussed. When the froth flotation route was decided upon, further tests were conducted on the selection of the equipment most suited to the particular requirements of this coal and the rest of the plant. Tests using different types of flotation cells and dewatering equipment are discussed. During the commissioning, several operational problems were encountered, and the work done to find the best solutions is discussed.

Jan 1, 1984

By T. Wennberg

An elevated location of a paste thickener on a ridge close to the disposal area is considered at a Swedish iron ore mine. About 0.7 M tonnes of thickened tailings are planned to be layered as paste in the vicinity of the thickener over several years with pipeline lengths of up to 900 m after about 20 years. In order to clarify the pipeline pumping characteristics of the tailings product for volumetric solids concentration from 40 to 50%, experiments in loop systems with pipeline inner diameters from 0.063 to 0.152 m have been carried out with various types of pumps. The results and comparisons carried out here showed that the performance of centrifugal pumps cannot simply be related to the rheology, but factors related to pump design and build-up tendencies of material within the pump and other particle properties may be of equal importance. During the first years of operation only one thickener underflow pump is required. The reliability and performance for various pump configurations are planned to be investigated systematically in order to meet the most effective long-term solution for paste thickener operation, pipeline distribution and placement in the disposal area as the discharge point advances over the life of the project.

Jan 1, 2007

By W. F. Heinz

The efficient and effective handling and logistics of materials for underground support is an important part of mine mechanization and automation. Support systems based on backfill material or grout slurries and pastes transported underground through pipelines (ranges) lend themselves to a large degree of mechanization. In contrast the installation of conventional support systems such as props, timber packs, brick packs etc., requires more handling and hence is labour intensive and more costly. RODIO/ROSOND has developed and improved significantly its high density slurry/low density paste conveyance system on surface and underground during recent years. The surface batching and pumping stations are computer controlled and operate with a minimum labour complement. The RODIO/ROSOND grout pack support system has some unique features such as the use of relay stations, which result in the following distinct advantages and benefits to mining operations: • No interference with shaft operations • No grout ranges under high pressure in shaft • Efficient reticulation from underground relay stations • Low capital cost • Better control of quality of materials (high density slurry/low density paste) placed • Proximity of the working place to the relay station facilitates control of installation. These specific characteristics of RODIO/ROSOND’s grout pack support system have resulted in more economical support for several mines in South Africa and Australia.

Sep 1, 2001

By L. S. Belyayeva, A. S. Chumak, N. N. Boyko, A. V. Bondarenko

Analysis of results of many years concerned study of the fire hazard parameters of the material of the mine conveyor belts come in for use at the mines of the Ukraine in 1984-2002 that was carried out in the laboratories of the Scientific-Research Institute of Mine-Rescue Work is adduced in the paper. The basic tendencies on raising the fire safety of the conveyor belts that are retraced in their world production are shown.

Jan 1, 2003

Tunnel Construction 90. London, Institution of Mining and Metallurgy, 1990. Reviewer: J.A. Cruise This is the published volume of papers presented at the Tunnel Construction 90 Conference, which was held in London in April 1990 under the auspices of The Institute of Mining and Metallurgy. Twenty papers are presented and their titles are listed below.

Jan 1, 1991

It is desirable to have a model, or method, for major project development, which will enable flexible modelling of separation circuits. This ability improves the understanding of circuits and how they should be operated, especially in a design phase, where various options are evaluated and decisions are made on the required number of stages and configuration. This paper describes existing gravity separation circuit modelling theory and concepts, as defined by Holland-Batt1 (separation window, separation efficiency and proportionality of efficiency). The crux of the paperis the application of numerical analysis to fit raw separation data by means of a modified Bézier-Spline. The paper proposes an alternative to the theory developed by Holland-Batt that provides more flexibility in the modelling of separation stages and curves, which include S-shaped curves. The paper proposes a solution to the challenge of continuously extrapolating data, and the first difficulty normally encountered, which is the fitting of an appropriate empirical formula to raw data.

Jan 1, 2007

By T. Vincent, J. Steele, C. Debrunner, M. Whitehorn

This paper presents current work on the development and use of stereovision for underground mining. Information on the calibration of the cameras and the feature-matching algorithm are presented. This system uses an intensity-based approach that evaluated correspondences along the epipolar line. Once features have been identified and their distance from the cameras computed, a three-dimensional map of the muck pile is developed. The approach used here uses a ray-tracing algorithm. This approach provides an uncertainty measure along with the elevation. A discussion of the use of this modelling information in the control of the LHD is included. Keywords: Robotics, automation, LHD, underground mining, vision sensing, task automation, tele-operation

Sep 1, 2001

A description is given of a simple, cheap device that enables the intact shear strength of rock to be determined quickly and inexpensively. Thin rock plates, prepared with a diamond saw, are tested in double shear by a linear punching action. By varying the direction of the diamond-saw cut in a number of specimens, the change in shear strength can be measured for different orientations relative to the rock fabric.

Jan 1, 1980

By J. P. M. Hojem, C. Dimitriou, N. C. Joughin

This paper describes the design and construction of the first experimental underground rockcutting machine from measurements of cutting forces determined in tests on small rock specimens in the workshop. The deficiencies of this design, revealed by stoping with almost identical rockcutting machines, are described. An account is given of the design and construction of further experimental machines incorporating substantial improvements which made them technically feasible for use in production.

By R. W. Ottermann, N. D. L. Burger, A. J. von Wielligh, P. R. de Wet, J. L. Steyn

Underwind and overwind protection system concepts for mine hoist shafts were developed in conjunction with and for the Safety in Mines Research Advisory Committee (SIMRAC). End-of-wind operation of mine hoists is the most hazardous aspect of mine hoisting, carrying the highest risk of loss of life, injuries to workers and loss of production. Systems operating mechanically and with local actuation were developed. This was done in order to remove the increased risk associated with dependency on remote or external energy and information supply associated with most existing protection systems. The proposed underwind protection system concept absorbs the energy of motion of a conveyance overrunning the design lower limit of travel by drawing a metal strip through a set of rollers. This action causes dynamic cyclic plastic bending of the strip material that converts the kinetic and potential energy of the conveyance into strain energy of the metal. In the concept design a pair of cable slings attached to the strips catch the overrunning conveyance and transfer the retardation force. The proposed overwind protection system concept absorbs the energy of motion of a conveyance overrunning the design upper limit of travel by early detaching of the conveyance from the hoist cable. This detaching is carried out via an additional humble hook activation mechanism fitted at a sufficient height below the spectacle plate to allow the conveyance to retard to standstill under gravity before it would crash into the spectacle plate. The conveyance so brought to rest is prevented from falling by means of jack catches on the conveyance interacting with a rack (toothed profile) fitted on the guide rails in the retardation zone. Scale models (1:10 scale) of both protection systems were designed for conformance with established retardation standards. The retardation standards were limited by the requirement of passenger safety in retarding cages. The models were then built and tested in a 1:10 scale shaft model. Retardation performance close to the required levels was achieved. The retardation distance required should allow such systems to be retrofitted to most existing shafts. Given the simplicity and robustness of the designs

Jan 1, 2003

By C. Nangolo

Mineral commodity prices comprise one of the key criteria in the selection of mining stocks. We contend that of the three principal elements of mineral commodity prices, spot price, forward price and long-term price, one has a greater impact on the share valuation processes used by investors. This research paper examines the extent to which each of these elements influences the valuation process. The intention is to provide investors in mining stocks with a greater understanding of how fluctuations of commodity prices over time affect the prices of the mining stocks they hold, or intend to sell or buy. Three mineral commodities, gold, silver, and copper, were used as case studies, since market data on these commodities is readily available in the public domain. Nine market indices covering all three mineral commodities were selected. These are based on clearly defined criteria with the intention of eliminating ambiguity and to test for correlation with the three sets of mineral commodity prices. Nine mining companies, which were not the primary drivers of the relevant indices employed in the study, were used to validate the results obtained from the indices in order to avoid duplication of the same correlation during cross-checking. Each commodity price was adjusted for operating costs. For each market index, an average operating cost was calculated from the companies comprising its basket, while each company?s annual operating costs were used for the stocks of the individual companies examined. The data was collected for the period January 2004 to October 2010. This period was further split up into three sub-periods to account for the Global Financial Crisis (GFC) period that started in mid-2008. We conclude that mining stock prices are correlated with mineral commodity prices, but with spot and forward prices exhibiting stronger correlations than long-term price. This finding should be useful for evaluation purposes. Where cash flow methodologies such as discounted cash flow or earnings per share are used to value ordinary shares and commodity prices are required to estimate future cash flows, the findings suggest that spot prices should be used as opposed to long-term prices. The work reported in this paper is part of a current MSc research study at the University of the Witwatersrand.

Jan 1, 2011

By L. R. Nelson

The efficiency and cost-effectiveness of the aluminothermic reduction process in the production of ferro-alloys and 'pure' metals depends strongly on appropriate balancing of the process energy required. Insufficient energy results in a poor metal yield, while over-supply can result in excessive fuming and possibly even ejection of the reactor contents in a potentially dangerous 'thermite bomb' reaction. This situation becomes even more critical when the suitability of limited quantities of oxide from new sources must be evaluated, dictating smaller-scale testwork. The resulting higher relative heat losses from the system complicates control of the energy balance, and usually requires the addition of thermal boosters or reactant preheating in order to sustain an autothermic process. This often detracts from the quality of the metal product, and adds to the hazards of batch aluminothermic- reduction testing. The development of a small-scale method (producing less than 2,5 kg of metal) for the plasma-assisted aluminothermic reduction of chromium oxide that overcomes such difficulties is described. The technique involves the use of a sealed 50 kVA plasma-arc furnace to provide controlled electrical ignition and supplementary energy to the reactants contained in a water-cooled copper crucible. The application of the method to the evaluation of the aluminothermic production of pure chromium metal from a unique chromic oxide source is reported.

Jan 1, 1996

By T. Ono, B. Altansukh, S. Kawamura, K. Haga, A. Shibayama, Y. Takasaki

In recent years, the grade of silica in zinc concentrate has increased due to the degradation of zinc content and the increase in impurity content in natural ores. It implies that the development of silica removal technology from zinc concentrate is necessary to solve problems in the smelting process caused by the high content of silica in zinc concentrate. In this paper, the authors investigated the silica removal processes from silica-rich zinc concentrate by mineral processing approaches such as re-grinding and flotation. This study focused on the pulverisation process as a pretreatment for the investigation of individual minerals' liberation from the silica-rich zinc concentrates using different kinds of pulverisers. Flotation experiments were performed to separate silica and zinc concentrate from the pulverizsd feed sample using a pH regulator (NaOH), activator (CuSO4), collecting agent (PAX), and foaming agent (DOW froth 250). Results showed that the liberation rate of silica (SiO2) was reached 75% from 13% by pulverisation in an attritor with a 2 mm ball in diameter, while silica accumulated in a fraction over 20 mm in size. Flotation experiments indicated that silica removal efficiency was achieved by 44% from + 20 mm fraction obtained from pulverisation whereas the grade of silica in froth reached 1.85 mass% from 4.5 mass%. Results indicate that silica could selectively separate from silica-rich zinc concentrate, and 99.8 % zinc recovery is achieved under the studied conditions. Keywords: Zinc concentrate, silica, pulverisation, liberation, sieving, flotation

Jan 1, 2020

By C. S. Erasmus, L. C. Woollacott

The distribution of gold loaded onto carbon particles from a carbon-in-pulp operation was measured by neutron activation analysis. The nature of the distribution is examined, and the implications for operating plants and CIP simulators are discussed.

Jan 1, 1992

By A. Whillier

Recommendations are given for the design of vertical cooling towers for use underground in mines and a method is given for predicting the entering and leaving water temperatures when a given amount of heat has to be dissipated.

By Z. Nzimande

The Constitution of the Republic of South Africa advocates the importance of sustainable economic development and justifiable environmental consciousness by business. The government needs to ensure that every citizen of the Republic has access to an environment that is protected, pollution free, and sustainable by enacting certain regulations. However, there are more than 5 700 derelict and unrehabilitated mines of all types in South Africa. Former asbestos operations were among the first to be targeted for clean-up under the programme instituted by the Department of Mineral Resources (DMR), owing to the proven direct impact of asbestos pollution on health. This paper seeks to investigate the challenges faced by the coal sector as far as mine rehabilitation and closure is concerned. For the purpose of this paper rehabilitation is defined as per the Chamber of Mines Rehabilitation Guidelines publication, which defines rehabilitation as putting the land impacted by mining activities back to a sustainable and usable condition. Some of the current rehabilitation challenges are technical skills (know-how), leadership focus, poor planning, cost saving initiatives, and the government's lack of capacity to enforcement rehabilitation requirements. It is imperative that mining companies identify rehabilitation as a critical strategic pillar that directly influences license to operate. The case study evidence indicates that relevant policies, appointment of accountable people, sufficient leadership support, and the correct choice of rehabilitation equipment can assist to improve the rehabilitation and land management challenge.

Jan 1, 2012

Book review Doyle, William S. Strip Mining of Coal; Environmental solutions. Park Ridge (New Jersey), 1976. 352 pp. $32. Surface mining of coal is still in its infancy in South Africa. The environmental repercussions following large-scale disturbance of the land surface, and the secondary effects of the disposal of waste products and effluents from mining, have not yet become apparent.

Jan 1, 1977