Search Documents

By R. Kosmicki

Wet end components of centrifugal slurry pumps used in the hydraulic transport of solids are subject to substantial erosive wear. Accurate prediction of the casing wear rate and location for a particular duty is beneficial for correct pump selection and design, maintenance planning, and elimination of emergency shutdowns. CFD multiphase simulation using the Eulerian-Eulerian approach is being applied successfully to determine the velocity fields and solids concentration in the centrifugal pump, allowing for accurate predictions of casing wear patterns resulting from sliding abrasive wear. Simulation results for various single domain and multi-domain (multistage) multiphase simulations are discussed. Emphasis is placed on results from a 3-dimensional, multi-stage transient, multiphase simulation and comparison to field data.

Jan 1, 2007

By D. D. Howat

In the field of high temperature smelting processes there have been two dramatic changes in the past twenty years. These are, first, the application of tonnage oxygen for direct injection for the refining of molten iron and other metals and to provide the means of enriching air used for the combustion of fuel. Second, the application of electric power for the generation of high temperatures in place of the combustion of fossil fuels. Of these two developments the application of tonnage oxygen for the refining of molten iron has virtually revolutionised the steel industry throughout the world. The magnitude of this development is exemplified by the fact that less than 5 per cent of the world's steel production in 1960 was made by this process or 16 million tons out of a total of 350 million tons of steel produced, while in 1970 over 40 per cent of the world steel production was made by this process, ie, 251 million tons out of 628 million tons total. In the same period the proportion of steel produced by the old-established open-hearth process has shrunk from 75 per cent to 38 per cent. In the whole history of the development of high temperature metallurgical smelting processes there has never been anything remotely approaching this. The other development, the application of electric power for the generation of high temperatures has not had the impact of the oxygen injection process but I believe that what we should call the electric smelting revolution in metallurgical processes has very far-reaching ramifications for steel production and other pyrometallurgical processes. This may seem a bold and brash statement but it must be remembered that the oxygen injection process constitutes a link in the chain critically dependent upon the production of vast tonnages of molten iron from very large modern blast furnaces. The Achilles heel of this chain of processes, upon which such a large percentage of the world's supply of steel depends, is the availability of metallurgical coke in turn dependent on natural resources of coking coal. Without any exception each industrial country in the world faces a shortage of resources of coking coal and in some cases a critical shortage. Certainly within the present century the major iron and steel producing countries of the world will face this critical shortage of coking coal and major modifications to steel making processes will become inevitable. W. F. Cartwright (Deputy Chairman of B.S.C) said recently that there are considerable doubts as to whether the world will be able to provide enough coking coal to meet world steel demands from the late 1970's onwards if the B.F.remains the main means for making iron from ore. This is one of the supreme ironies of the world metallurgical situation to-day when the technology of iron and steel production has reached an extremely high peak of technical efficiency. The newest modern iron blast furnace capable of producing 6 000 to 8 000 tons per day of molten iron represents probably the most efficient piece of high temperature metallurgical plant and operation known to man. The conversion of this molten iron into steel by the oxygen injection process has made available to the engineering industry steel of a quality and at a price which is quite remarkable. Yet this vast metallurgical pyramid rests on the completely insecure and uncertain foundation of inadequate world resources of coking coal. The shortage of reserves of coking coal in this country is acute and it is possible that these resources will be exhausted within the next twenty years. Yet unless some completely unexpected catastrophe occurs the demand for steel in this country will probably rise at a faster rate than in the Western world due to the expansion of the Bantu population and the increased standard of living. To offset the inevitable shortage of coking coal are our much greater resources of bituminous coal which although of low grade provide a suitable fuel for electric power generation. The geographical disposition of the coal fields in relation to the great industrial areas of the Transvaal makes it inevitable that the development of the pyrometallurgical industries must depend heavily on electric power. The position in this country with regard to electrical power generation and consumption is rather anomalous. Per capita consumption of electric power is high - in 1964 almost twice the world average of 870 KWH and twenty-five times the average of 34 KWH for the Continent of Africa. In 1964 fifty-four per cent of the total world electric power was used in industry - the ratio being approximately 1/9 mining to manufacturing uses. As shown in Table I in 1969 67.2 per cent of the total output of electric power from ESCOM was used for mining and other industrial uses but almost in the ratio 6/4 mining to industrial uses. These figures emphasise the enormous importance of the mining industry to the economy of this country and underline the major contribution made by the gold mining industry. What is of very significant importance is that although the mining industry remains by far the largest single consumer of electrical power the consumption of power for industrial uses is rising rapidly as shown in Table II.

By S. Nana, M. B. Cortie

Duplex stainless steels containing high levels of manganese and copper and lower-than-normal levels of nickel were produced and evaluated. The experimental alloys containing 3 per cent copper by mass could not be successfully hot-rolled. Alloys containing less than 2 per cent copper could be hot- and cold-rolled without difficulty. The wrought experimental alloys that contained copper were found to offer some advantages over the 2205- type duplex stainless steel in sulphuric acid at 52°C. Resistance to pitting attack was governed primarily by the chromium, molybdenum, and nitrogen contents, and one of the experimental alloys was superior to the 2205-type alloy in the ferric chloride test. It is concluded that manganese is a useful substitute for nickel in duplex alloys, but that further work is required before the present alloys, or variations of them, could be commercially viable.

Jan 1, 1993

By S. Venter, W. E. Stumpf

Some of the factors that govern the choice of a nuclear fuel are briefly discussed, special reference being made to the introduction of advanced carbide fuels into fast-breeder programmes. One of these factors, i.e. the compatibility of carbide fuels with stainless-steel cladding, is discussed in depth. A very sensitive technique for the study of compatibility interactions between fuel and cladding is described in respect to the effects of particle size, specific surface area and surface oxidation of the fuel,and microstructure of the cladding on the compatibility behaviour of the cladding with the fuels. Finally, the need for the development of modified or stabilized uranium carbide fuels is discussed, and some results are presented to show the effects of small amounts of sulphur in these fuels on their compatibility with stainless-steel cladding materials.

Jan 1, 1979

By J. E. Forbes

Oxygen enrichment of the converter air at Rustenburg Platinum Mines by J. E. FORBES (Associate Member)* An account is given of the adoption of oxygen enrichment to accelerate converting operations and so permit the handling of larger quantities of feed materials. In addition to achieving its object, the use of oxygen-enriched air (6 per cent oxygen by volume) results in an increase in the concentration of sulphur dioxide in the converter off-gas. The slags have the same composition as those produced without oxygen enrichment, and the operation of the converters is easily controlled.

Jan 1, 1977

By J. Levin, I. J. Corrans

Wet high-intensity magnetic separation (WHIMS) for the concentration of gold and uranium was tested on many Witwatersrand cyanidation residues, and on some ores and flotation tailings. The results varied, but many indicated recoveries of over 60 per cent of the gold and uranium. The main source of loss is the inefficiency of WHIMS for material of smaller particle size than 20fLm. The recoveries in the continuous tests were lower than those in the batch tests. The continuous tests indicated an operational difficulty that could be experienced in practice, namely the tendency for wood chips and ferromagnetic particles to block the matrix of the separator. It was decided that a solution to the problem lies in the modification of the separator to allow continuous removal of the matrix for cleaning. A system has been developed for this purpose and is being demonstrated on a pilot-plant scale. Promising results were obtained in tests on a process that combines a coarse grind, gravity concentration, and WHIMS. In the gravity-concentration step, considerable recoveries, generally over SO per cent, of high-grade pyrite. were obtained, together with high recoveries of gold and moderate, but possibly important, recoveries of uranium. A simple model describing the operation of the WHIMS machine in terms of the operating parameters is described. This should reduce the amount of empirical test work required for the optimization of operating conditions and should provide a basis for scale-up calculations. The economics of the WHIMS process is discussed.

Jan 1, 1979

Colloquium and General Meeting A General Meeting and Colloquium was held on 'New Advances in Non-ferrous Pyrometallurgy' in Kelvin House, Johannesburg, on Wednesday, 17th March, 1976. The President, Dr R E. Robinson, opened the proceedings at 1OhOO,by welcoming the authors and delegates, who numbered approximately one hundred and twenty. Tinplate Conference The Tin Research Institute is organizing the 1st International Tinplate Conference, which is to be held in London from 5th to 8th October, 1976.

Jan 6, 1976

By M. H. Marsden, R. A. Laybourne, J. D. Flint

Operations of the strip mine at Arnot Colliery are described, and the improved volumetric extraction of the in situ coal reserves that has been obtained by the application of strip-mining techniques is highlighted. An account is given of the major problems encountered during the early stages of the operation with particular reference to overburden removal. coal and parting handling, and transportation. The techniques used in dealing with the problems and the current degree of success in overcoming them are outlined.

Jan 1, 1980

By W. J. Jordaan

The ability of soils to retain and hold cations is called the cation exchange capacity (CEC). Adsorbed cations, however, can be replaced by other cations through the process of cation exchange. Heavy mineral deposits contain a significant portion of slimes including the very fine clay minerals. In most circuits the slimes fraction hampers efficiency and has to be removed during early stages of the process. Being a nonvaluable process stream, the processing of the slimes is a costly exercise. In thickening applications it might be possible to manipulate the ability of clay minerals to retain and hold positively charged cations in order to optimize flocculation and therefore reduce flocculation costs. The CEC value of the slimes could be a measure of this possibility. To investigate this hypothesis, different slimes samples were characterized for size, chemical composition and clay minerals present. The CEC value of each sample was determined and explained in terms of the mineral phases present. Settling tests were conducted and an attempt was made to explain the CEC characteristics of the clay minerals in terms of settling rate. The scope of this investigation was to test the hypothesis and should not be seen as an in-depth study of the subject matter. A greater number of samples and detailed analyses to identify and quantify minerals and phases present would be required to investigate further the relationships between clay minerals in the deposit, CEC and settling rates. Location and geological setting Exxaro KZN Sands is mining a heavy minerals deposit at Hillendale mine located at Richards Bay, South Africa. The orebody consist of a dune some 8 km inland from the coast to the north of eSikhawini. A geological synopsis undertaken by Botha1 concluded that the Hillendale mining area represents a coastal dune sequence that accumulated north of the Tugela River. The northward movement of sediment by long shore drift currents result in a high sand budget on the beaches north of the river youth and is the dominant contributing factor to the accretion of the coastline and development of parallel dune systems along the coastal zone in this area. Beach swash zone processes and enrichment of the fine sand fraction occurs during wind transport off the beach by ascending parabolic dunes that form the coastal barrier dunes. This process results in heavy mineral concentration on the windward dune face and localized enrichment parallel to the dune forms. The aeolian sedimentary facies processes result in the primary concentration of higher grades in the upper silt-enriched reddish brown horizons of the profile. The synopsis by Botha1 further showed that an additional component of heavy mineral concentration can be ascribed to the post-depositional relative enrichment of heavy minerals due to weathering. Therefore, it is likely that the Hillendale orebody protolith was pedogenically weathered to form the homogeneous, silt-enriched, clayey reddish brown to dark red, palaeosol profile that grades downwards into yellowish brown, less clay-enriched sand. Slimes characterization Samples The Hillendale orebody was divided into geochemically discretized zones based on the concentration of ilmenite and other specific minerals and/or phases. Six composite samples were made up from exploration samples taken from Zone 9, Zone 11 and Zone 12. The red and orange horizons within these composite samples were separated and test samples were prepared to conduct test work and analyses. The test samples were submitted for preparation and analysis to characterize the slimes properties. Each test sample was deslimed at 45 µm representing the slimes fraction (-45 µm) and dried at 40°C. The -45 µm slimes samples were then split to conduct size analysis, chemical analysis, XRD and to determine the CEC. Size analysis The size distribution of the composite samples is shown in Table I. The size analysis shows that there is a difference in size distribution between the orange and red horizons of each zone. The orange horizons contain less 850 µ material as well as less slimes (-45 µm). The red horizons contain yore slimes (-45 µm). The size distribution of the slimes fraction (-45 µm) was determined using Malvern size analysis. The cumulative particle size distribution of the slimes is shown in Figure 1. The red horizons of the different zones show similar size distributions. The orange horizons show some differences. However, there is a difference in size distributions between the red and orange horizons.

Jan 1, 2007

The key functions of project evaluation are to assess potential profitability and to develop an effective operational design. For mining projects, design aspects include mining methodology, ore treatment methodology and production rates. All of these characteristics impact on project economics and overall value. Resource models, which form the ultimate basis of project evaluation, typically consist of tonnes above cut-off, grade above cut-off and the spatial distribution (connectivity) of tonnes/grade above cut-off, for one or more variables. Dilution, ore loss and metallurgical recovery are all modifying factors applied to the resource model during evaluation and determination of profitability. A key issue is: how is the value determined? In addition to traditional combination of in situ tonnes/grade, the following merit serious consideration: the concentration of deleterious elements, throughput rates, mining/processing costs and - importantly - metallurgical recovery. Geometallurgy is an emerging field targeted at integrating these issues by identifying either direct measures or proxies for throughput (hardness, grindability), recovery (liberation, mineral shape/texture, etc) and concentrate quality from easily collected macro-, meso- and microscopic data. These 'geometallurgical variables' drive project costs and revenues in a fundamental way. For geometallurgical characterisation to have a real impact on business design, it must enable improved mine planning. When creating spatial estimates for such variables, it is preferable to find proxies that can be measured as close to the intact rock mass as possible. However, spatial estimation of proxies for geometallurgical properties and responses is complex and requires special consideration. Unlike grades, both proxies and absolute measures of geometallurgical variables are not necessarily linear or additive and therefore require very careful geostatistical consideration. In some cases, models must predict extreme values of geometallurgical attributes rather than averages. Incorrect characterisation of metallurgical recovery/throughput can (and has) led to misspecification of the scale of projects, and thus can be seriously value destructive. Aspects of geometallurgy have long been important in iron, bauxite, manganese and coal deposits and are increasingly on the radar for base and precious metal miners. However, as more metallurgically complex deposits are developed and mining of large-scale, low-grade deposits becomes more commonplace, the importance of characterising the metallurgical response in order to generate properly optimised projects will rapidly increase. It is possible that in many `traditional' (ie grades and tonnes) reserve models, the variables that drive the project are missing!

Jan 1, 2007

By M. I. Brittan

SYNOPSIS The key reactions of the copper segregation process have been studied with a view to establishing the kinetics of the system. The investigation was carried out using two refractory copper ores from the Zambian Copperbelt in a small-scale, fluidized bed, chloridization reactor. The rate of chloridization of the copper in the ores is compared with the rate of volatilization of the cuprous chloride produced and with the rate of reduction of the cuprous chloride to form segregated metallic copper. In conjunction with available data on the rate of production of hydrogen chloride in a segregation system and with due regard to the conditions applicable in a TORCO reactor, it is concluded that the chloridization reaction is the major rate limiting step of the process. Factors influencing the rate of this extraction step and aspects of its mechanism are examined. The findings have confirmed the validity of the existing theory of segregation and provide insight as to the viability of the system of reactions involved in the copper segregation phenomenon. Experimental results which relate to observations made in the course of TORCO plant operation and segregation studies are discussed.

By N. Birtek, R. P. King

The washability characteristics of fine South African coals were measured and were found to be well characterized by an M-curve having the equation Z = aQb exp(cQ) x dQ, where Z is the ash content per 100 units of total feed and 0 is the mass yield. Parameters a, b, c, and d were determined for 23 different samples of coal from important coal seams in the main South African coalfields in the size range 0,0025 to 1 mm. The relationship between ash content and relative density was determined and correlated by means of two linear relationships. This characteristic behaviour was explained in terms of the liberation of macerals and the different association between the mineral mater and the two major macerals vitrinite and inertinite. The results obtained in this study can be used to calculate the expected performance of an ideal separation process, and can also be used as input for the simulation of real beneficiation plants. An example is worked through in detail to illustrate the method of calculation.

Jan 1, 1990

By M. B. Algeo, R. H. A. Plaistowe

A method of forecasting the haulage trucks required for a large open-pit operation is described. Emphasis is placed on the effects of changes in planning and on the complexities of a mining operation that involves many benches and dumping areas.

Jan 1, 1979

By M. C. van Blerck

This paper outlines the tax provisions that became defective in January 1992, which allow a working mine to make tax-deductible contributions to a dedicated environmental body that is itself not subject to tax. Such a body will then provide a source of funding for the mine's future environmental expenditures. It is concluded that the establishment of such environmental bodies is a financially sound, tax-effective route, allowing mines, prospectors, and quarry operators to provide for future environmental rehabilitation.

Jan 1, 1994

By D. W. Horsfallt

The above paper gives a fair amount of information and is a useful addition to the literature on a subject of growing importance. I believe that more experimental results could have been given, together with more details of the modifications made to the plant that enabled it to operate with the success mentioned in the paper. One important omission is a definition of the word fines. As pointed out elsewhere!, this word is used very loosely.

Jan 1, 1980

By T. Gibson

It is generally accepted that South African coal mines have gone through the mechanization of most of its underground mines, and while there certainly were a lot of productivity improvements, the lack of visibility on these machines operating underground still leave vast areas for improvement. The average actual cutting time still remains very low, in the 30 per cent area, which leaves significant improvement possible. Currently all analysis is carried out using hand-written reports. Unfortunately this is subjective and often inaccurate because of human interpretation. In addition in order to avoid costly component failure, a monitoring system is required to warn of eminent failures and condition monitoring. The challenge faced was to supply and install a system that was ‘Open’ and could be retrofitted to existing machines in operation because of the current standard of communication links to the underground sections. In addition it was intended to use, existing ‘off the shelf’ software and hardware and adapting this for the harsh underground mining conditions wherever possible in order to reduce costs. As development occurred, as with all technology, doors opened to other opportunities such as, remote access data logging and Internet based reporting. We focused on the Voest Alpine Bergtechnik (VA) range of continuous miners, as need arose to achieve the desired cost improvements because of the strategy of service contracts the subsidiary company, Voest Alpine Mining & Tunnelling (VAMT) offer the mining industry in South Africa. This paper describes a data logging system that has been installed on various continuous miners that provides data in real time, on line, and that could be expanded to any electrically supplied underground mobile or stationary mining machine.

Sep 1, 2001

By A. D. Pienaar

The aqueous chemistry of niobium and tantalum compounds with hydrofluoric acid is a mature field of investigation. In contrast, very little attention has been paid to reactions of these compounds in non-aqueous environments. Similarly, reactions of elemental fluorine with niobium and tantalum compounds have received little more than cursory attention in literature. This work discusses the isothermal reaction kinetics derived from thermogravimetry, using a less redundant approach than is currently the standard. We also discuss the most likely kinetic models for this reaction.

Jan 1, 2012

A set of six design principles for rock engineering was developed by Bieniawski: design objectives; minimum uncertainty; simplicity of design components; state-of-the-art practice; optimization; and constructability. These principles translate into a ten-step design process. Although this methodology was developed for rock engineering, it is applicable to any design process, feasibility study, etc. Diligent use of such a process will ensure that a defensible design or evaluation has been carried out. Recently a ?strategic conversation? process has been identified by Ilbury and Sunter that includes the following ten steps: scope; players; rules of the game; key uncertainties; scenarios; SWOT analysis; options; decisions; measurable outcomes; and meaning of winning. A comparison of these steps with those of the design process shows a remarkable correlation. This is perhaps not surprising since engineering design is a strategic up-front issue, and front end loading in a project is critical to achieve the expected project performance. Based on the close correlation between the strategic conversation and engineering design processes, a circular design process, rather than a linear process, is proposed. The ?circle of design? better reflects the importance of review and monitoring in the two phases of successful design and implementation?defining the design, and executing the design.

Jan 1, 2009

By J. Jacobs

The three-product cyclone was originally developed in Russia and is now extensively used in China. The cyclone has recently entered the South African coal industry, and with the obvious advantages that this item of process equipment offers our ever-evolving industry it is safe to assume that it will add value to dense medium circuits in South Africa. Some of the possible applications include: ? Producing multiple products using a single dense medium circuit. These can typically be a primary product with calorific value of 27.50 MJ/kg and a secondary (middling) product with a calorific value of 22 MJ/kg ? High-density separation with a low circulating medium density. Anglo Thermal Coal and Exxaro have pioneered the use of these units at Umlalazi and New Clydesdale respectively. Extensive test work has been performed at Umlalazi to determine the efficiency of the unit and to determine how it compares with the conventional DSM (Dutch School of Mines) cyclone. Some people in the coal industry were initially sceptical and expected the performance of the three-product cyclone to be inferior to that of the conventional dense medium cyclone. The results of the test work have, however, shown that the efficiency of the unit is comparable to that of the cyclones currently employed. A valid concern expressed is the control over the cut-point density of the second stage separation, and work is on-going to find the optimal way to control the secondary separation density. Theoretically, the secondary separation density can be manipulated by changing the orifices of the unit, especially the spigot of the secondary stage. This remains to be proven, and a series of tests is currently being planned. Whatever the result of these tests may be, the three-product cyclone definitely has a place in the South African coal processing industry as it offers a low OPEX and CAPEX solution for producing multiple products from a single circuit, as well as the ability to operate at very high separation densities, while making use of low-density circulating medium. Keywords dense medium separation, DSM, three-product cyclone, coal processing.

Nov 1, 2013

By K. A. G. Blendulf

The paper describes tests on horizontal-belt filters for the filtration of gold and uranium. The promising results led to the installation of 17 such filters (ten of them 120 m2 in size) in the mine's metallurgical plants, and their operation is discussed. Although several problems were encountered both in operation and maintenance, it is concluded that, with correct operation and suitable filter cloths, exceptionally good metallurgical recoveries can be achieved at filtration rates twice to three times higher than those on rotary filters.

Jan 1, 1997