Search Documents

By C. L. E. Swartz, I. J. Barker, J. H. Schubert

A dynamic simulator of the leaching and adsorption cascades of a gold plant was developed and used to compare the effect of various disturbances on the overall efficiency of the plant. These comparisons show which disturbances most critically need to be controlled to optimize plant performance. The simulator was based on an existing gold plant. Dynamic and steady-state data were collected on the plant and were used in the modeling of the process. Simple dual-rate models are used to describe the leaching and adsorption processes. Mole-balances of various species take into account the changes of concentrations in the leach, and also the movement of pulp and carbon up and down the adsorption cascade. Fluctuations in the flow rate, density, and cyanide concentration of the feed to the leach have a negative effect on the efficiency of the leach, while carbon attrition was found to be an important factor in decreasing the efficiency of the carbon-in-pulp (GIP) section. Badly regulated transfers contribute towards the decreased efficiency of the GIP section, but overflows and carbon leakage have only a limited long-term effect. Various carbon profiles and transfer schemes were studied, and the results indicated that a slightly heavier loading at the bottom of the cascade is beneficial, while the type of transfer is relatively unimportant.

Jan 1, 1993

By J. M. Stewart, C. H. Wyndham

Suggested thermal stress limits for safe physiological strain in underground environments by J. M. STEW ART M.Sc. (Eng) (Witwatersrand) (Visitor) and C. H. WYNDHAM M.B., D.Sc. (Witwatersrand), F.R.C.P. (Land) (Fellow) A comparison of safe temperature limits, based on Mitchell and Whillier's equations for specific cooling power (SCP), with similar limits determined experimentally shows the SCP-based limits to be unnecessarily conservative. It is argued that, while a small part of this conservatism may be attributed to an erroneous extrapolation of the heat transfer dependence on wind speed, the major part is probably due to the use of too Iowa limiting mean skin temperature in the calculation of SCP. A combination of Mitche/l's basic data with results available in the literature permits the derivation of modified heat transfer equations based on data that fully cover the range of wind speeds of interest. These equations, using a mean skin temperature of 36°C as the basis for the calculation of safe temperature limits, are then shown to agree favourably with those determined empirically. Furthermore, values of SCP based on these equations are shown to correlate reasonably well with wet kata readings, giving positive support to the wet kata thermometer as a heat stress meter.

Jan 8, 1975

By T. B. S. Giddy

The advantages to be gained from the use of a high-density ion-exchange resin in a uranium recovery circuit are shown. It is concluded that, in existing fluidized-bed plants, the throughput of solution can be increased by up to 40 per cent at the same uranium recovery. Alternatively, the values in the barren solution can be improved at the same flow-rate of solution.

Jan 1, 1980

By B. Steyn

AngloGold Ashanti?s Obuasi Mine, in Ashanti Province, Ghana, operates a plant utilizing bacterial oxidation technology. The mineralization consists predominately of arsenopyrite with gold associated in the sulphides. The plant was commissioned in 1994, at that time was the largest BIOX® plant in the world, and has been operated by AngloGold Ashanti since 2004. The constraints identified in the plantwere the flotation capacity, BIOX® feed size and disruptions to the BIOX® process. This paper focuses on the practical steps that were followed in order to increase the recovery of the plant. The original plant design was based on a head grade of 10 g/t and an overall recovery of 86.5%. In 2007 the plant was operating at an overall recovery of 79.2% at a head grade of 5.6 g/t and this has improved to 80.6% at a head grade of 5.8 g/t during the last quarter of 2008. Additional improvement to 81.5% are expected by the end of April 2009. Improvements that have been implemented include: ?Replacement of the regrind mill ?Installation of additional float capacity ?Installation of a scavenging circuit ?Installation of a complete water treatment plant. In addition we have focused on the effect of the water circuit on the BIOX® process and the steps involved in correcting this problem. The water circuit was originally designed as an open circuit and through environmental considerations the circuit was closed towards the end of 2007. The bacteria in the BIOX® are particularly sensitive to cyanide and cannot tolerate levels above 0.05ppm (free cyanide), this required extensive modifications to the water circuit. The plant improvement project is ongoing and the current scope of work should be complete by the end of April 2009. Further research and development work is being planned, which includes a ?white rot bacteria? that can consume the preg-robbing carbon and oxidize the sulphide in a single pass.

Jan 1, 2009

By P. Kind

Design criteria and recent developments in large-capacity Wemco flotation cells by P. KIND, Ph.D. (Clausthal), B.Sc. (Visitor) The scaling-up of the large flotation cells that have been developed during the past few years has been based on hydrodynamic considerations and has resulted in a 500 ft3 cell unit. Plant results on a porphyry copper ore show that the 500 ft3 unit is equivalent to the previously used 300 ft3 model.. . Plant tests on the use of 300 ft3 flotation cells for the recovery of phosphate, particularly from the coarse size fractions, are also described.

Jan 3, 1976

By Z. Weisheng

The lift system is the main part in manganese nodule mining on the ocean bed. It connects the nodule collection system (miner) with the surface platform (mining vessel) and transports the nodules from the ocean bed to the surface. China started the research on lift technology in deep ocean mining in 1991, and a slurry pump hydraulic lift method has been developed for the nodule mining system. The detailed slurry pump hydraulic lift experiments have been undertaken with crushed nodules in the vertical pipe. The lift parameters to lift coarse particles in the lift pipeline have been discussed, including the pressure drop, the solid concentration, and the mixture velocity. The author of this paper not only took part in all these studies on the lifting technology, but was also responsible for some of this research. This paper will present the component parts of the lift system and the research results of coarse particle mixture flow in the vertical lift pipeline. Keywords: deep sea mining, slurry pump lift, lifting parameters.

Jan 1, 2007

By A. O. Filmer

An account is given of a study on the non-oxidative dissolution in aqueous acidic solutions of nickel sulphides of different stoichiometric composition, in which a rotating ring-disc electrode was used. The rate of dissolution was found to depend on the potential of the sulphide and the nickel-to-sulphur stoichiometric ratio. A maximum rate for the dissolution of nickel from nickel sulphides containing an excess of nickel was recorded at potentials around -0,2 to -O,3V. The rate decreased markedly at more anodic potentials. For nickel-deficient nickel sulphides, the nonoxidative dissolution rate increased with a cathodic shift in potential. Under open-circuit conditions, a nickel sulphide of a composition approximating Ni ,S. reacted most rapidly. The dissolution rate was controlled by either a chemical or an electrochemical reaction at the electrode surface, had an activation energy of between 50 and 65 kJ.mol-1, and was independent of stirring speed.

Jan 1, 1980

By D. -X. Li

The paper covers many literature reports of processes using nitrogenous species as an oxidant for processing refractory gold ores, especially development in the pretreatment of refractory gold minerals by nitric acid. These processes include the high-pressure and the atmospheric-pressure oxidation methods. High-pressure oxidation processes are difficult to carry out, because they require high-capital cost autoclaves. Atmospheric-pressure oxidation processes are easier to manipulate, but complete absorption and reuse of NOx is difficult or multiple-stage absorption must be established for its reuse. So, some new methods were developed, such as catalytically oxidizing technology of NOx to allow subsequent recovery of gold. Keywords: nitric acid; pretreatment; refractory gold

Jan 1, 2009

By F. L. D. Cloete

The Relix process is based on direct contact between an ion-exchange resin and undiluted pulp, thus avoiding prior solid-liquid separation. The resin particles float near the surface of the pulp, forming an inverted fluidized bed with the pulp flowing downwards. The basic idea was demonstrated on a full-scale pachuca tank at Stilfontein Gold Mine in 1970, followed by a small-scale demonstration run in a laboratory at the National Institute for Metallurgy. A pilot plant based on a throughput of 60 tons of ore per day was subsequently operated at West Driefontein Gold Mine for several periods over two years. Although the plant proved operable from a mechanical point of view, the metallurgical performance was not up to expectation. The basic cause of the poor metallurgical performace was shown to be backmixing of both the resin and the pulp between stages. The values obtained for resin losses were inconclusive. Further development of resin-in-pulp processes for the recovery of uranium should be focused on the performance of various techniques for the screening of resin from pulp.

Jan 1, 1981

By A. Koursaris, J. B. See

The influence of Iscor coke and Delmas coal on the reduction of Mamatwan manganese ore to ferromanganese was examined by use of a variation of the 'stationary charge in controlled environment' (SCICE) technique. The charges of Mamatwan ore and the appropriate reducing agent were heated to temperatures between 1300 and I600 °C and either allowed to cool immediately the required temperature had been reached or held at that particular temperature for periods of up to ... hours. The heating rate was 350°C per hour, the particle size of the ore was between 2,83 and 12,7 mm, and the particle size of the reducing agent was between 2,83 and 6,35 mm. After being allowed to cool in air, the reacted charges were examined by optical microscopy, X-ray-diffraction analysis, scanning electron microscopy, and electron-microprobe analysis. No significant difference was found between the changes observed during the reduction of Mamatwan manganese ore by Iscor coke and by Delmas coal. A hypothesis is advanced to explain the mechanism of formation of the Fe-Mn-C alloy.

Jan 1, 1979

By D. J. Stanton

The objective of this study was to develop, install, and test a small underground mobile refrigeration plant (MRP) to deal with some of the real problems associated with mine cooling in an operating mine. The requirement for cooling the underground environment is discussed with particular emphasis on the need for this method of cooling, with the concomitant benefits. The research investigated current methods of cooling and reasons for previous failures in MRP. Both static and dynamic simulations were conducted to increase the confidence level under operating conditions. Implementation and testing, resulted in ?lessons learnt? requiring modifications, which are documented. Actual results have been recorded. These results have proved that significant cooling via MRP is feasible. Main benefits include positional efficiency, cost per kilowatt of cooling and cooling opportunities for remote hot areas of a mine. Finally, a proven technology is now available for large-scale implementation in the mining industry. Now the ventilation engineer has another system of cooling, which can be utilized in the quest to create an occupational environment, which meets the physical and mental health requirements of the worker.

Jan 1, 2004

By W. J. Kempson

As a result of the rising electrical energy costs in South Africa, a method was sought to reduce the overall electrical consumption of typical shaft systems. A typical shaft configuration was analysed and the primary energy consumers were identified. The ventilation fans for this system were found to consume 15% of the total energy of the shaft system. It was calculated that more than 50% of this energy is consumed by the shaft itself, more specifically, by the pressure losses that occur in the shaft as the ventilation air passes through it. In order to ensure that the theory being used for the evaluation of these shaft systems is accurate, a total of five shafts were instrumented and the actual pressure losses over the shafts plotted against time. These shafts were then analysed from a theoretical perspective. Finally, in order to ensure a thorough understanding of the behaviour of the ventilation air in shaft systems, the systems were simulated using computational fluid dynamics (CFD) techniques. There were significant discrepancies between the theoretical analysis and the CFD simulation during the initial comparisons. This discrepancy lessened as the complexity of the CFD models increased, until when the complete shaft was modelled using the full bunton sets, the pipes, and the flanges, the difference between the theoretical evaluation and the CFD simulation was small. This result demonstrates that the theory is insufficient and that the interrelated effect of the buntons and fittings has not been fully appreciated by current theory. The final phase of the work presented here was to evaluate the costeffectiveness of using different bunton shapes and shaft configurations. It is shown that the increase in the pressure losses and therefore the direct operating costs of the shaft can vary by as much as 80%, depending on the bunton configuration chosen. The placement of the piping in the shaft can increase the pressure losses, and therefore the direct operating costs of the shaft, by as much as 12%, depending on the placement of the piping in the shaft; this effect includes the use of flanges. The use of fairings on a large cage can reduce the resistance that the cage offers to the ventilation flow by as much as 30%. This, however, does not translate into a direct saving because as the cage moves through the shaft, the overall effect is transitory. These savings can be significant when the items highlighted in this work are applied correctly. Keywords shaft design, ventilation, energy consumption, modelling, CFD.

Dec 1, 2013

By W. C. Joughin

A risk evaluation model has been developed, that enables the quantification of expected injuries and economic losses resulting from rockfalls associated with a support system in a given geotechnical environment. This enables the comparison of different support systems based on the expected frequency of injuries and the total cost of the support system, including the expected economic losses. The model takes into consideration the variability in joint orientations and joint strength within the geotechnical environment and the variability and quality of support systems. The quantification of the benefits of other rockfall risk-mitigating strategies, such as the effectiveness of barring or monitoring, are also incorporated in the model. The risk model is described in this paper and the validation of the model and case studies are described in Part II.

Jan 1, 2012

By F. T. Cawood

This paper reviews the Mineral and Petroleum Resources Royalty Bill of 2006, identifies potential areas that require further consideration by the National Treasury and, where appropriate, offers alternatives. At its basic level a royalty regime consists of two elements: the base and the rate that must be applied to the base. Deciding on an acceptable royalty rate is a complex matter and can be done only after extensive analysis of all variables affecting the competitiveness of the regime. The proposed royalty rates are in the range of zero to five per cent and are based on sales revenue. It is argued that future investment patterns are more likely to be influenced by market cycles and commodity prices than policy events. Inevitably the current boom in the minerals sector will come to an end and the success of the proposed regime will be known only when profit margins are under pressure. Policy makers must therefore have the long run in mind when developing policies that affect the ability of industry to do business, without the need to renegotiate each time there is a change in the market. A long-run policy must be sufficiently flexible to allow for consistently fair sharing ratios and splitting of revenues between government and industry. Although broadly in line with international practice, the current version cannot be regarded as internationally competitive and efficient. In order for the royalty bill to become internationally competitive, promote beneficiation of mineral production and adequately compensate the State for the loss of a national resource, the National Treasury should heed the following main recommendations in this review: 1. Abandon the notion that each mineral product must have its own royalty rate; 2. Introduce an NSR type royalty that allows for value-addition costs to be deducted from the base; and 3. Provide for automatic relief through the use of a sliding-scale mechanism based on ability to pay, e.g. the X-Factor used in the gold mining tax formula.

Jan 1, 2007

By M. Rudolph, J. Sygusch

Froth flotation is well-established and efficient in the selective separation of valuable particles from unwanted material with sizes ranging from 10 μm to 200 μm. However, when it comes to the separation of ultrafine particles (< 10 μm) there are still some challenges, or rather opportunities. This research aims at developing a method for the separation of ultrafine particles based on multiple particle properties. Amongst such properties are wettability, morphology (shape or roughness) and size with applications not only in mineral processing but in general chemical engineering. In this study, three differently shaped fractions are used as valuables for testing: spherical particles, elongated particles and irregularly shaped particle fragments; together with ultrafine magnetite as the gangue material, in order to investigate the effect of particle morphology on ultrafine particle flotation, as well as wettability, which is varied by esterification using alcohols. Flotation tests are carried out using a novel flotation device that was designed especially for the flotation of ultrafine particles, combining advantages from machine-type froth flotation and column flotation. The results showed that, in contrast to previous studies, recoveries for ultrafine spheres were higher than for ultrafine fragments for all wettability conditions, and hydrophobisation generally increased particle recoveries for said morphologies. Tests using fibres showed different behaviour as hydrophobisation had negative effects on their recovery, despite increased selectivities and kinetics. These findings suggest that apart from influences of particle properties within the suspension zone, their effects on the froth characteristics should be studied in more depth. Keywords: Ultrafine particles, Flotation, Particle shape, Wettability, Esterification of glass, Hydrophobisation

Jan 1, 2020

By L. Ozdemir, B. Asbury, T. G. Rozgonyi

A new type of bit, that has been developed and is being evaluated, shows great potential in expanding the range of rock strength that can be cut by continuous miners and roadheaders. This new style of bit is called the frustum. The tools tested in this program were developed, manufactured and patented by Briese Industrial Technologies, Inc. The frustum derives its name from the unique geometric shape of the cutter, or cutting insert. The frustum shape cutting tool has previously been proven as an effective cutting tool for machining metals, metal matrix composites and polymers. The frustum rock bit has a very dense carbide frustum shape tip mounted on the end of a steel body similar to the conical bits typically used on continuous miners and roadheaders. In between the carbide frustum cutting tip and the steel body there can be a bearing that allows the frustum to rotate around the bit axis. When the bit is forced into the rock at a skewed angle, the frustum tip rotates as it travels. This rotation greatly reduces the cutting forces acting on the bit when compared to the current state of the art conical drag bits. This cutting force reduction, derived from the frustum’s cutting action, allows for much harder and more abrasive rock to be cut without quickly wearing out the bit. Full scale laboratory cutting tests have been performed with the frustum bit in direct comparison to the current state of the art conical bits. Field trials of the frustum bit are currently being planned. Test procedures, results and findings are presented.

Sep 1, 2001

By E. E. Almási, G. Mucsi, G. Rákhely, Á. Rácz, B. Csőke, Zs. Pap, K. Bohács, N. Halyag

Wet stirred media milling is a widely applied grinding process in the field of mineral processing to produce <10 μm ground materials. In this paper, the results of wet stirred media milling of different Ti, Fe and Cu-oxide and phosphate minerals are presented. During the experimental work, grinding of ilmenite, vivianite, hematite and cuprite was carried out in a continuous operation wet stirred media mill. During the experiments, the particle size distribution and specific surface area of the ground materials were determined after a certain grinding time, as well as measuring the specific grinding energy, thereby determining the grinding kinetics of the different minerals. The measurement results showed the differences and similarities in the grindability of the individual minerals. Nano particulate vivianite, hematite and ilmenite was successfully manufactured in a stirred media mill; however cuprite was characterised as the coarsest final product for the same grinding circumstances. Keywords: Wet stirred media mill, cuprite, vivianite, ilmenite, hematite

Jan 1, 2020

By M. Pierce, E. Karampinos

"One of the main challenges in the numerical modelling of ground support in underground excavations is to reproduce the performance of the sequential installation of the reinforcement while capturing the rock mass behaviour of an advancing face in 3D. The 3D modelling approaches used to simulate the progressive advance of excavations are mostly continuum and often cannot reproduce the rock mass failure mechanisms. The 3D discrete element method (DEM) can better reproduce structurally controlled rock mass failure mechanisms and can explicitly represent the reinforcement elements. This paper builds on previous work that reproduced the structurally controlled squeezing conditions in an underground hard-rock mine using 3D DEM and the in situ behaviour of reinforcement under pull conditions. It addresses important issues on the way reinforcement is explicitly introduced in discrete element models. A pseudo-3D model is employed to overcome the computational restrictions and time limitations of a 3D modelling approach. The work focuses on the scaling of the material properties of the ground support elements when the thickness of the model is not equal to the out-of-plane spacing of reinforcement. It demonstrates the scaling methodology based on the type of the modelled reinforcement elements used and investigates the significance of this approach. The advantages and disadvantages of this approach with respect to 2D and 3D methods are discussed. The results are compared with field data and previous modelling work done at the mine. IntroductionNumerical models can provide significant insight into the anticipated behaviour of underground excavations. The modelling of ground support, however, is not a trivial exercise. An effective representation of ground support in underground excavations should capture the behaviour of both the rock mass and the support elements. When numerical models are used for design purposes, the complexity of the problem requires significant time and expertise (Sweby, Dight, and Potvin, 2016).At a laboratory scale, numerical models have successfully reproduced the results of laboratory tests on rockbolts by explicit modelling of the bolt, the borehole, and the grout. Chen and Li (2015) used a continuum FLAC3D (Itasca Consulting Group Inc., 2012) model to simulate the mechanical behaviour of D-bolts as observed experimentally. Grasselli (2005) used a 3D finite element code to model the behaviour of fully grouted rods and expandable bolts under shear."

Dec 1, 2018

By Q. G. Reynolds

The dual-electrode direct current (DC) arc furnace uses two graphite electrodes, one connected as cathode and one as anode. Such an arrangement avoids some of the design difficulties associated with the anode hearth traditionally used in single-electrode and twin-cathode DC furnaces, but can introduce other design and operational difficulties including deflection of the arcs toward the furnace walls. Counter-intuitively, both arc jets in a dual-electrode furnace travel from the electrode down to the bath surface, despite carrying electric current in opposite directions?this is suggested in the theory of the governing equations of arc formation, and confirmed by experiments using high-speed photography. The dual-electrode arc system at small pilot-plant scale is studied using a transient magnetohydrodynamic model capable of predicting arc deflection and interaction from first principles, and the results are compared to the behaviour of twin-cathode systems at similar power. Finally, a simple arrangement of the furnace busbars, M configuration, is shown to provide some passive protection against arc deflection.

Jan 1, 2011

By D. Lunt

This paper describes and sets in context the commercially proven uranium extraction processes. It also discusses some of the technologies that are currently being pursued with the aim of reducing costs and overcoming a number of technical issues that are faced by process designers and operators. In doing so, opportunities for the transfer of extraction technology from other industries/commodities are identified. The key processing areas that are examined include: ?The influence of mineralogy. The type of uranium mineralization and the nature of its association within a particular deposit will have a major impact on process route selection. Uranium minerals are classified according to their influence on extractive metallurgy. As the uranium price has risen in recent times, so opportunities are increasing for the recovery of uranium from less conventional resources such as phosphates and fossil fuels. ?The opportunities for employing techniques aimed at reducing the capital and operating costs of the overall process such as heap leach and beneficiation. Preconcentration by screening, gravity separation and radiometric sorting can potentially reduce the mass flow to the downstream leach and recovery plants. ?Purification or separation of uranium in carbonate systems. While it is possible to directly precipitate uranium from clarified leachate, the presence of impurities such as vanadium, molybdenum and others may dictate that ion exchange or selective precipitation is employed. Advances have been made in other industries in terms of improved ion exchange equipment aimed at reducing resin inventories and hence costs. ?Separation in acid leach systems. Earlier developments included the use of combined SX-IX systems (Eluex or Bufflex) and the introduction of continuous countercurrention exchange (CCIX). Column SX has found a ready application to uranium in view of the rapid extraction kinetics. With the renewed interest in uranium processing, efforts are being redirected towards further development of resin-in-pulp (RIP) as a means of driving down capital and operating costs. ?Extraction in a chloride environment. Australia and Namibia are desert countries where good quality water comes at a cost. However, both have access to saline water from either the ocean or subterranean aquifers. The issues associated with operating a uranium extraction operation in such environments is discussed. ?Extraction from less conventional sources. Recent price increases for U3O8 have resulted in a number of companies examining the recovery of uranium from sources such as fossil fuels and phosphate deposits. Both of these areas were examined in the 1970s and 1980s and a number of approaches were commercialized. The paper reviews the extraction options.

Jan 1, 2007