Search Documents

By A. T. Sweet, G. Douglas Gardner

"INTRODUCTION In the ammonium sulfate process for the production of alumina from clay,,3/ the clay is baked with amonium sulfate at about 400ºC. to form anhydrous ammonium alum and free ammonia or ammonium carbonate. The alum is leached from the baked product with water and circulating liquors and is purified by recrystallization. Aluminum hydroxide is precipitated by treating thus alum the alum the ammonia or ammonium carbonate from the baking step. Ammonium sulfate is recovered from the filtrate for reuse, and the aluminum hydroxide precipitate is calcined to produce high-purity alumina. In this process, as in other acid processes for the production of alumina, 4/ a large part of the iron in the clay is extracted. The iron tends to build up in the leach liquors and contaminate the crystals, so that its elimination is one of the most important problems in the process. A number of large clay deposits occur in the Western States. Those that have boon explored most extensively 5/contain an average of 24 to 30 percent available A12O3 and 2 to 8 percent available Fe2O3. 6/ The available Fe2O3 content of various other clays ranges from less than I percent to more than 20 percent. The available Al2O3 or Fe2O3 is usually 90 to 98 percent of the total but may be much less. In generals the iron content bears no fixed relation to the alumina content and may vary widely within a given deposit."

Jan 1, 1948

By David C. Grant

In situ uranium mining offers the advantages of minimal environmental disturbance, low capital and operating costs, and reduced mining development time. It is becoming an increasingly attractive mining method for the recovery of uranium from secondary ore deposits. In order to better understand the process, a laboratory technique was developed and used to study and simulate both the chemical and physical phenomena occurring in ore bodies during in situ leaching. The laboratory simulation technique has been used to determine effects of leaching variables on permeability uranium recovery, and post-leach aquifer restoration. This report describes the simulation system and testing procedure in sufficient detail to allow the construction of the system, and to perform the desired leaching tests. With construction of such a system, in situ leaching of a given ore using various leach conditions can be evaluated relatively rapidly in the laboratory. Not only could optimum leach conditions be selected for existing ore bodies, but also exploitation of new ore bodies could be accelerated.

Jan 1, 1985

By L. A. Stewart

This paper describes all occurrences of barite in Arizona that were known or reported to the authors. The history, ownership, production, and geologic setting are discussed for most of the deposits. The uses and specifications of product grades are briefly discussed. Seventy-five deposits were examined in 9 of the 14 counties of the State. The descriptions are given under county headings. No occurrences were reported in the four northeastern counties of Coconino, Navajo, Apache, and Greenlee, nor in Santa Cruz in the southern part of the State. From about half of the deposits examined, 55 samples were taken; of these, 45 were for chemical analysis, and 8 larger samples, ranging from 100 to 350 pounds, for beneficiation tests. A 30-ton bulk sample was taken for pilot-plant tests. Bench-scale flotation tests of the eight samples employing several different procedures and reagent combinations yielded marketable-grade barite products with barite recoveries ranging from 60 to 97 percent. Five of the samples contained enough fluorspar to warrant its recovery. Acid-grade concentrates, which accounted for fluorspar recoveries of 45 to 70 percent, were obtained from three of these ores. Batch laboratory tests of a representative portion of the 30-ton bulk sample revealed that acid-grade fluorspar and high-grade barite concentrates could be recovered. Results of the laboratory and continuous pilot-plant tests of this ore will be presented in a separate report.

Jan 1, 1960

The Government of New South Wales has granted approval for Hunter Valley Aluminium Pty., Ltd" and Alcan Australia Ltd. to proceed with the building of an aluminum smelter at Lochinvar and the expansion of a smelter at Kurri Kurri. Construction of the smelters is expected to start as soon as the consortium is finalized in early 1982. The smelters are part of a plan to increase Australia's aluminum capacity fivefold to 1.5 million tons by the mid-1980's. CHILE Construction of a $61 million lithium carbonate plant in northern Chile will be started in early 1983 by Sociedad Chilena del Litio Ltdao Production is scheduled to begin in 1984 with an initial capacity of 6,350 tons of lithium carbonate produced from a brine deposit. The firm is owned 55% by Foote Mineral Company, of Exton, Pennsylvania, and 45% by Corporacion de Fomento de la Produccion-CORFO.

Jan 1, 1982

Objective To reduce dust generated from soiled floors within enclosed operator cabs. Background Enclosed operator cabs are widely used on mobile excavation equipment in the mining and construction industries. They protect the operator from bad weather, noise, and airborne dusts. The inside cab environment usually must be kept at very low dust concentrations because of quartz dust generated from the excavation of silica-bearing rock. For cabs to be effective in controlling airborne respirable dust, they must have an efficient air filtration system, while providing a positive pressurization of the cab interior. Ideally, the recirculated and exterior makeup air filtration should provide at least 99% capture efficiency for dust particles as small as 0.3-µmaerodynamic diameters. Many of these enclosed cabs use heating units mounted or directed along the floor (see figure 1), which can cause dust entrainment problems. Prior studies by the National Institute for Occupational Safety and Health (NIOSH) of enclosed cabs have shown that these floor heaters can generate notable amounts of dust within the cab enclosure (see Technology News 486). Multiple-shift dust levels measured inside a drill cab increased on average from0.04 mg/m3 during the summer months to 0.68 mg/m3 during the winter months. Additional dust level measurements, made with optical particle counters during a nondrilling time period, verified that dust levels inside the cab increased from 0.03 to 0.26 mg/m3when the floor heater/fan was turned on. Dust levels within the cab also became greater than the ambient air dust levels outside of the cab when the floor heater was turned on during the nondrilling time period. This shows that the floor heater was a notable dust source problem. Cab floors are commonly soiled from operators tracking dirt inside the cab upon entering from the mine or construction site. Interior cab dust levels can be increased by (1) airflow disturbance of the soiled floor or (2) operator disturbance of the soiled floor. Approach During prior NIOSH surveys of surface coal mine drills, several drills with very low cab dust levels (#0.1 mg/m3) were observed to have floor sweeping compound spread out over the cab floor during the working shift. This initial observation led to a more controlled A-B study of the effect of the sweeping compound on the interior cab dust levels. This study involved dust sampling with and without sweeping compound inside the cabs of a bulldozer and two drills. Sweeping compounds commonly use sawdust or cellulose as the main bulk material, with oil or wax added for dust adhesion purposes. Sand is sometimes added to increase bulk density. Sweeping compounds with sand are commonly used to sweep up concrete floors. Those without sand (usually referred to as "gritless") are used to sweep up smooth finished floors. Most of the oils and waxes used for the adhesive ingredient are petroleum-base and can have an irritating odor. People sensitized to petroleum distillates could have allergic reactions to these sweeping compounds. A few companies offer non petroleum-base sweeping compounds, using either a natural oil or chemical additive for dust adhesion. During this study, it was decided that only the gritless sweeping compound (without sand) would be used, eliminating the addition of another potential silica source inside the cab. Since the sweeping compound would be applied on the enclosed cab floor for the duration of the shift, it was decided to use a canola oil-base sweeping compound to eliminate irritating odor from the petroleum-base sweeping compounds. The natural canola oil-base sweeping compound had a slight woody scent. The three pieces of equipment used in this study had notably different cab layouts. The bulldozer had a small cab with vents discharging air-conditioned or heated air from adjustable louvers at operator waist level and floor level. The bulldozer also had a cloth fabric seat and a carpeted floor. Drill A had a large cab with the heat directed from adjustable louvers at operator knee level and the air-conditioned air directed from cabin ceiling louvers. This drill had a vinyl fabric seat and a steel plate floor. Drill B had a small cabin with the heat directed across the floor (see figure 1) and the air-conditioned air directed down from the ceiling. It had a vinyl fabric seat and a worn rubber mat on a steel floor.

May 1, 2001

By F. A. Rutledge

The Batesville district in north central Arkansas is one of the important sources of manganese ore and ferruginous manganese ore in the United States, with a history of production dating back to 1849. From studies by the Federal Geological Survey, it was recognized that the district probably still contains substantial reserves of low-grade ore. It was natural, therefore, that the deposits in this area should be among the first investigated by the Bureau of Mines under the Strategic Materials Act of June 1939, by which the Bureau was authorized to explore domestic deposits of strategic minerals, at that time designated as those of antimony, chromium, manganese, mercury, nickel, tin, and tungsten. The field work of the Bureau of Mines in the Batesville district was done in two distinct phases. Under project 308, active from August 1940 to June 1941, carbonate-oxide ores were investigated at five separate areas in which 100 trenches, test pits, shafts, and edits aggregating 4,364 linear feet were excavated and 839 samples were taken and assayed. Under project 323, in progress from February 1941 to January 1942, wad deposits were explored at 10 separate areas by 408 prospect shafts, churn-drill holes, and bucket-drill holes aggregating 23,680 linear feet from which 285 samples were taken and assayed. Processes for beneficiating the wad ores were investigated at ore-testing laboratories of the Bureau of Mines.

Jan 1, 1952

By M. C. Chapman, P. L. Swanson, A. T. Iannacchione

The National Institute for Occupational Safety and Health (NIOSH) evaluated microseismic activity from three field sites to compare and contrast the characteristics of microseismic emissions from very different geologic, stress, and mining environments. Recently, NIOSH has embarked on a research program to evaluate the use of microseismic monitoring information to identify roof fall failure processes and to assess its potential to warn of unstable roof conditions. Large roof instabilities, such as roof falls and certain roof caving events, have proven difficult to anticipate representing an increased risk to miners working in these inherently hazardous areas. When local failure processes are better understood, appropriate control measures can be engineered to mitigate these hazards. This study used microseismic emissions to help identify three local rock failure processes. It was also shown that analysis of microseismic emissions can aid in assessing the degree of instability associated with these local rock failure processes.

By E. O. RHODES

Germany's' wartime coal-tar industry had two main branches, which can best be considered individually because their raw materials, operations, and distributions were almost completely separated. One branch, old and well-established, was concerned almost entirely with processing coal tar produced by the high-temperature carbonization of caking bituminous coal. Carbonization was effected principally in byproduct- coke ovens and to less extent in vertical, horizontal, and inclined retorts. The high-temperature tar was all processed in tar-distilling plants that handled high-temperature tar almost exclusively.

Sep 1, 1947

By John A. Kiefer

Ground fault and overcurrent protection criteria for coal mine a.c. distribution systems were examined under a Bureau of Mines funded investigation. The report begins with a literature review which discusses relaying topics including instrument transformers, ground-fault pickup methods, static relaying, and comparison of relaying techniques. A chapter on ground-fault relaying provides recommendations for maximum and minimum pickup levels as a function of maximum ground current and power system line-to-ground capacitance. Research in the area of phase overcurrent protection has resulted in a complete set of procedural recommendations for the selection and setting of overcurrent relays and current transformers, molded-case circuit breakers, and distribution system fuses in coal mine power systems. The final chapter, which discusses relay system maintenance, introduces a unique test set which was developed by KETRON and used to test the performance of relaying systems in coal mines.

Jan 1, 1980

By J. F. Barkley

To reduce fuel consumption in industrial and commercial fuel-burning plants throughout the Nation, cooperative efforts of thousands of individuals are required. These individuals are scattered over the country and hold various positions in thousands of independent establishments. To accomplish as much as possible on this problem during the Second World War, it was decided that personal contact with fuel users was absolutely necessary; publicity, although an important factor, could not by itself give satisfactory and needed results. It was planned to have qualified engineers visit commercial establishments to go over with them the problem of reducing their fuel consumption. The specific plan, toward which all efforts aimed and around which the rest of the program revolved, consisted in brief of 1. Conference of visiting engineer with management to obtain cooperation. 2. Appointment by management of a plant employee as fuel "waste chaser." 3. Work of engineer with "waste chaser" and, if appropriate, with plant operators on most efficient operation of equipment.

Jan 1, 1948

By Chas. F. Jackson

This paper is one of a series dealing with mining methods and costs, prepared and published under the sponsorship of the United States Bureau of Mines and made possible through the cooperation f many mining companies in the United States and foreign countries. The preparation of this paper follows a field study of top-slice mining during which the author visited and discussed with operating officials a large number of iron mines in the Lake Superior region. During this study special note was made of changes in top-slicing practice during the past decade, prior to which the author had acquired several years experience with the method through active connection with a number of mines employing top slicing.

Jan 1, 1931

By H. William Zeller, T. E. Westpha1

The U.S. Bureau of Mimes evaluated the effects of two iron-based fuel additives on diesel particulate matter (DPM) emissions. The 5.6-L, six-cylinder test engine is typical of engines used in underground mines. One additive, ferrous picrate, did not measurably affect exhaust emissions. This report is mainly about a ferrocene-based additive that reduced DPM between 4 and 45 pct, depending on engine operating conditions. The report concludes that the DPM reductions were caused by the catalytic oxidation properties of a ferric oxide coating that developed inside the engine's combustion chamber. The ferric oxide coating also decreased gas-phase hydrocarbons and O, but it increased CO, and NO,. The increase in NO,, of about 12 pct, is considered the only adverse effect of the ferrocene-based fuel additive. The results suggest that the effectiveness of ferrocene was partially offset by increased sulfates because of the high-sulfur fuel used. Recommendations for continuing fuel additive research are presented.

Jan 1, 1992

By H. P. Greenwald

[For sarno years past the Safety in Minbr. Resaarch J30ard of Great Bri tr-dn ha:1 been making ar.. intensive Gearch for, traterials that \.'ould be 1!\ore ef-ficient than rock dust and th t 'could l1eplace it Jholly or in El:}rt as a muans of prevEll'ltine the propa 'tion' of 'c63.1~dust exnlosions in. mines21 In the course of this \o.'ork several rock c.ur--ts md numerous inorganic compounds I,/ere tested. The result w place incombus.ti ble substFlnces in two main groups~ (1) r.:ho se who sa effect' in suppre aeina Jlihe cor.lbustion of coal dUDt i 0 pro-]

Jan 1, 1940

By D. E. Pollock, Andrew B. Cecala

It has long been known that ventilation is a cost-effective method to lower respirable dust concentrations in all types of mining applications. The National Institute for Occupational Safety and Health has been working on a number of different research techniques that use ventilation as a critical component to lower respirable dust levels at surface and metal/nonmetal operations in the United States. This article presents five such research efforts. The first research area discusses how improving the ventilation flow patterns in an iron ore mill facility lowered respirable dust concentrations by 31 pct throughout the primary grinding area. The second research area examines how respirable dust levels were lowered at a dimensional stone shop by using air cleaning units suspended from the ceiling. A third area discusses how improvements in ventilation at underground limestone mines lowered respirable dust concentrations. The fourth area examines how improvements in dust filtration and pressurization systems significantly impacted the air quality in enclosed cabs of surface mining equipment. The last area presents a newly developed clothes cleaning technique. This technique uses an air spray manifold to blow dust from a worker’s clothing in an enclosed booth, which confines the dust for capture and removal by a baghouse dust collector. These research areas represent an array of different control technologies to lower respirable dust concentrations. Ventilation is an integral part of these control technologies.

By R. Karl Zipf, David Newman

The objective of this is paper is to review the current state of knowledge and practice in highwall mining (HWM). HWM has become a widely-applied method in surface mining, commonly used alone or in conjunction with contour or slot mining. It provides 800-feet to 1,200-feet of additional recovery when the economic stripping ratio is reached in contour mining or in slot mining when surface access to a reserve is limited. A significant attribute of the highwall miner is its versatility. HWM has been used successfully to mine abandoned pre-reclamation law highwalls, points or ridges uneconomic to mine by underground or other surface methods, outcrop barriers left adjacent to underground mines, separate benches of the same seam where the parting thickness or quality differences between benches render complete extraction uneconomic, previously augered areas containing otherwise inaccessible additional reserves and close or widely spaced multiple seams. The theory and design methods to assess roof, pillar, and floor stability are presented followed by three case histories. Simple design charts for sizing HWM web and barrier pillars are also presented. A recommended web pillar width may be obtained from the design charts given the overburden depth, the HWM cut width, and the mining height. Given the depth and panel width for a set of HWM cuts, another set of charts gives a suggested barrier pillar width. The case histories, from Northern and Southern Appalachia are used to illustrate the application of rock mechanics to quantify the stability of the highwall, roof, web pillars, and floor. The case histories involve 1) mining through a previously augered highwall, 2) mining under back-stacked spoil and 3) selective mining of closely spaced benches of the same seam. Because each site is unique, the appropriate pre-mining geotechnical analyses range from the calculation of roof, web pillar, and floor bearing capacity stability factors to detailed numerical modeling of the auger and underground mine workings. When operating in the vicinity of existing underground mine or auger workings, the determination of ground deformation and strains resulting from highwall mining is a necessary facet of a ground control investigation.

By Arthur L. Murray

"INTRODUCTION In compliance with those provisions of the organic act establishing the Bureau. of Mines which relate to improvement of health conditions of persons engaged in the mining, preparation, or treatment of mineral substances, sanitary surveys have been made of towns and villages housing the coal miners, metal miners, and mill and smelter employees of Utah.The purpose of the surveys is to afford studies of conditions prevailing in the various mining and smelter towns so far as concerns housing, water supplies, sewage disposal, refuse disposal the handling of foodstuffs, general sanitation, wash and. change houses, and the control of preventable diseases, all of which directly or indirectly have a bearing on the health and efficiency of employees and their families. Certain other factors have been added to the general sanitary surveys such as school and recreational facilities, which have a decided influence on contentment and efficiency. Through comparisons of favorable and unfavorable conditions and practices, and the dissemination of such information, improvements can be effected which will benefit both the employees and the employers.ACKNOWLEGMENTSAcknowledgment is made of the many courtesies shown by the officials of companies and towns visited. In some instances the towns were entirely under the control of officials of mining companies, being on company property whereas, in other instances, the towns wars incorporated not under company management. Particular acknowledgment is made of the assistance given by the Utah State Board of Health through Health Commissioner Dr. T. B. Beatty."

Oct 1, 1932

By William A. Beck

This report describes the loading and transportation practices employed at the zinc-lead mines of The Eagle-Picher Co., Jo Daviess County, Ill., and Lafayette County, Wis. The report also gives a brief history of the Illinois-Wisconsin zinc-lead district and the operations of the company in the area. The diesel-powered, rubber-tired loading and haulage equipment is described and illustrated from the operational point of view only, and an analysis is made of the materials-handling system without going into health and safety factors. The costs per ton of the various components of mechanical loading, underground haulage, underground crushing, and hoisting for fiscal year 1960 are tabulated.

Jan 1, 1964

By H. C. Fuller

This paper discusses 105 production runs at Boulder City, Nev., in which titanium metal was made in 200-pound batches. It describes the equipment and techniques used in preparing raw material, the reduction process, and the removal of the reaction mass from the reaction vessel. Also, some data on man-hour requirements are presented. The main emphasis was on producing ductile-grade titanium and developing a standard procedure for obtaining a consistently pure product. Some departures from techniques used before were found to be desirable. The most important of these was the use of a sealed room with a controlled dry atmosphere in which the reaction vessel was opened and the reaction mass removed. This minimized the moisture taken up by the magnesium chloride in the reaction mass, and it could be purified successfully by vacuum distillation. Using the dry room also made it possible to leave al-inch shell of the reaction material on the walls of the vessel, which lowered the iron contamination and eliminated the labor and time-consuming job of cleaning the vessel after each reduction. Another change was lowering of the temperature during reduction to 750° C. instead of 850° C. This was found to give good results more consistently. The first poke to break the crust during reduction was eliminated, as it was found to be unnecessary and only added more work and was another possible way of introducing air. A rotating feed arm was installed in the reaction vessel to distribute the titanium tetrachloride over a larger area and, thus, prevent local overheating. The process, conducted in a batchwise manner as described and followed by good purification and fusion, produces a metal adequate in quality for nearly all purposes.

Jan 1, 1952

By Madan M. Singh

This report presents the results of an investigation of inclined roof bolts, anchored over pillars, in room-and-pillar coal mines susceptible to shear failures of the roof. Although the field data do not support this contention, it is believed on the basis of analyses and other work that inclined roof bolts do offer potential under some circumstances.

Jan 1, 1978

By C. W. Owings, J. J. Forbes

"Although coal-mine explosions rank third among causes of underground fatalities, they receive more wide-spread attention than any other accidents in mines because frequently many persons lose their lives in a single disaster. Each bituminous coal-mine explosion endangers the lives of approximately 100 persons--the average number employed underground in a commercial mine. A critical analysis of coal-mine explosions in a restricted district gives a cross-section of relative existing explosion hazards, of common causes of ignitions of gas and dust, and of effective prevention measures. The Safety Division of the United States Bureau of Mines is collecting data on coal-mine explosions in the various States, and this circular is one of a series analyzing the causes and recommending methods for thy prevention of similar occurrences,The data on this circular are based on records of the United States Bureau of Mines and the West Virginia Department of Mines. Unfortunately practically all of the early records were destroyed by fire in the State House at Charleston, W. Va.; the remaining records were made available to the authors by N. P. Rhinehart, chief of the Department of Mines, and his cooperation is gratefully acknowledged.The earliest available reference to coal in West Virginia is that made by John Peter Lally who in 1742 found ""a great plenty of coals"" near a river later called Coal River. In 1809, Nicholas Roosevelt found coal along the Ohio River and used it on the New Orleans, said to have been the first steamboat west of the Allegheny Mountains. In 1810, Conrad Cotts opened a mine near Wheeling and sold coal for domestic purpose in 1812, a mine was opened on the Ohio River opposite Mason City and produced 1,200 bushels of coal that year. In 1840 the total West Virginia coal production was 298,691 tons; in 1863, the production had increased to 444,468 tons, and in 1883, to 2,335,833 tons. During this period apparently most of the coal was extracted from coal outcropping on the hillsides; little danger of gas ignition existed at that time, but explosions from blown-out shots occurred frequently. On February 22, 1383 the West Virginia legislature enacted legislation providing for a mine inspector to inspect the mines of that State, to prevent mine accidents, and to insure properly ventilated mines.In a special report to the Governor on December 31, 1884 the Inspector of Mines reported:We have 5 shafts, in 4 of which there is more or less gas; and in 1 of our drift mines there was an explosion on the 27th day of March 1880, whereby 2 men were killed and a boy badly burned.Table 1 lists 287 explosions in West Virginia coal mines. Several early explosions were listed in the annual reports of the West Virginia Department of Mines as ""blown-out shots"" or ""powder explosions"". The injuries usually were described; explosives accidents have been eliminated from these and other available data, and only those in which dust or gas were involved have been included in this paper as explosions."

Sep 1, 1934