Search Documents

By Gabe McClain, Thomas Pallua, Joe Schrank, William C. Gates

Because of restrictions on blasting in urban areas and, more importantly, the proximity of this construction to national historic landmarks, blasting operations were extensively monitored to measure and correlate ground vibrations as peak particle velocity (PPV), frequency, and strain—these being the major factors that would impact the surrounding buildings. As a result, copious amounts of data were gathered and interpreted within a short time to estimate blasting parameters and optimize the subsequent blast rounds

Feb 1, 2020

By Bonifacio Degay, Mike Lovitt

PT Freeport Indonesia is a block cave mine that now utilizes an advanced undercut method to set up the min in the Deep Ore Zone (DOZ). In this method a slice of rock (undercut) is broken such that it sits on top of the drawbell level. The drawbells are developed to channel the broken ore into the extraction level and to enable the caving orebody to be drawn out in an even and controlled manner. These drawbells are difficult to form due to the small amount of void that can be developed in the low strength rock before firing. Starting with two rises of 2m square, the void ratio for the entire drawbell around 6%, which would normally result in a frozen and unproductive blast. Orica -Mining Services have worked with PT Freeport in a collaborative effort to find a solution to the mining problem. With excellent control of timing of the blasting it is possible to get fluid flow of blasted rock out of the draw points such that more void can be made available for blasting the remaining parts of the drawbell. The i-konTM electronic blasting system gives the exacting control of timing within the blast to achieve this Dynamic Void Generation (DVG). The solution stops the need to charge close to brows in the drawbells and reduces the cost and time related to developing initial blast voidage. This paper identifies the results of the trials including design, photographic evidence and vibration analysis. The flexibility and accurate timing of this electronic blasting system has enabled single hole initiation rather than 4 or more holes being initiated together, thereby reducing the damaging vibrations to the extraction level.

Jan 1, 2004

By Santiago Gómez, Pablo Segarra, José A. Sanchidrián

In this paper, differences between the industry-standard Holmberg-Persson (H-P) approach and a semi-analytical vibration prediction model called full-field solution (FFS) are analized. The analysis is conducted at two levels: vibrations and rock damage.

Feb 1, 2020

By Ashley Haslett

A European Directive on Identification & Traceability of explosives came into effect on the 4th of April 2008. This directive is intended to establish a harmonised system for the unique identification and traceability of all packaged explosives, detonators, reels of detonating cord and primers used in civil applications across the European Union. The directive must be adopted into the national legislation of each European Union member state by the 5th of April 2009 with compliance achieved throughout Europe by the 5th of April 2012. The requirements of the Directive apply to all explosives manufactured, used and imported into the European Union from 5th April 2012.

Jan 1, 2010

By Huang Daguang, Paulo Couceiro, Juan Navarro

Mining is typically conducted through a set of interdependent unit-operations, which commonly include drilling, blasting, digging and hauling, in order to deliver the required ore material into the comminution circuit and to remove waste rock with minimum impact in the operation. In such complex environment, the identification of critical paths, and respective interfaces between different unit-operations, are necessary to determine a sustainable long-term operational program. Facing this challenge, adaptive cost optimization strategies are required to increase productivity and revenue while minimizing potential environmental impacts. Since the overall mining efficiency can be strongly impacted by blasting outcomes, an operating method based on the searching of the ideal blast design is required in order to minimize the mine total cost of ownership. The implementation of a consistent continuous improvement program requires specific care in terms of design, control and execution of the different stages of blasting. For that, the application of the most advanced technologies for rock characterization, based on drill monitoring systems, and smart explosive products, allows the improvement and control of blast results by adapting the explosive energy distribution to the rock condition, so as to optimize the performance of downstream stages such as digging, hauling and comminution. This paper describes the application of a heuristic optimization approach, where blast parameters are used as decision variables to evaluate the potential impact of several blasting scenarios on subsequent unit operations, under the continuous ability of modelling, measuring and calibrating operational performances along of the mine cycle.

Feb 6, 2023

By Adam Stremcha, John MacGregor

Initial planning called for 3 separate drop shafts and 3 separate vent shafts to be pulled back from the excavated tunnel with a large diameter raise bore machine. With time constraints and the raise bore machine already in high demand on other shafts, a more “traditional” drill and blast approach was taken on a few of the larger drop shafts. This decision proved to be not only cost effective, but also reduced schedule impact as the shafts were excavated simultaneously with the other raise bores.

Jan 1, 2010

By Amos Bryant, Jesse Davis

This paper compares the predictions of the latest Institute of Makers of Explosives Safety Analysis for Risk (IMESAFR) model versus physical test data recovered from ISO-1 and ISO-2 tests in Woomera, SA. ISO-1 testing included placing 1054 kg (2324 lbs) of ANFO (ammonium nitrate-fuel oil) inside an ISO container on a flat bed truck. ISO-2 testing was identical except the NEW was 4000 kg (8818 lbs). The IMESAFR predictions are based on model runs using the best match available to the actual donor type involved in the test. This type of debris analysis is not the standard output of IMESAFR, as the program is designed to assess the probability of human fatality. However, all of the IMESAFR predictions presented were obtained from the use of the actual model equations and algorithms without adjustment. Test results from ISO-1 and ISO-2 will be presented as well as findings from the comparison between model results and actual explosive results from the ISO testing efforts.

Jan 1, 2010

By Robert Boehnke, Bernd Mueller

This contribution presents an innovative, statistically supported method to predict blast vibrations in rock mass. For modelling the processes during and after detonation, a theory is employed which is based on linear momentum (so-called momentum theory), strongly supported by new measurement methods. During the course of the investigations, the following parameters have been found to dominantly influence vibrations: ! charge WB, includes geometrical factors such as borehole length and diameter (kg) ! detonation velocity cd of the explosives used (m/s) ! distance r between the points of emission and immission (m) and the statistically determined negative exponent n ! factor RM or RS of the rock mass which is related to the specific blast momentum and the drilling and blasting technique used and is statistically determined together with the exponent m (mm/kg or mms/kgm)

Jan 1, 2004

By Guillermo Lazcano Ríos, Jorge Parvez Aguirre, Alejandro G. Díaz Berríos, Felipe Rodriguez Alveal

Codelco's Chuquicamata Underground Division (DCHS) faces issues due to collapses in its subsidence streets, which hinders the advancement of the subsidence front and leads to the loss of areas and reserves. To address these issues, DCHS and Orica have developed a new excavation methodology based on pre-loading explosives in high drawbell. This methodology involves creating a high drawbell extending from the floor of the production level to the ceiling of the subsidence level, divided into two phases: upper and lower. A resin stemming is used to separate these phases. The excavation strategy adjusts to variables such as reception volume, fluffing, and excavation geometry, involving vertical pre-loading of the explosive and the use of a separating element between the phases. The test aims to validate the new excavation methodology and the retaining element in the rock mass, evaluating aspects such as drawbell geometry, impact on the rock mass, damage to the retaining element, and fragmentation. Wireless electronic detonators are used in the upper phase to improve safety by eliminating the need for physical connections, while traditional electronic detonators are employed in the lower phase. Low-density bulk emulsion is applied to minimize the impact on the Crown pillar and extraction point, and higher-density explosives are used above the subsidence level to ensure good caving. Results showed that the blast achieved 86% conformity with the theoretical design. Resin stemming allowed for 100% effective detonation in the upper columns, and the fragmentation obtained was 5.44 inches, which was less than expected. No damage to the Crown pillar was observed, and the explosive quality met standards. This technique has proven to be effective and viable, suggesting the possibility of eliminating the subsidence level in future levels, resulting in savings, and providing greater stability to the rock mass.

Jan 21, 2025

By Corry Goumans, Ron J. Elliot

This paper discusses the challenges encountered in drilling and blasting of a small diameter shaft underneath a parking garage in historic Gastown, Vancouver, BC. This project involved drilling in a restricted headroom area, blasting in a confined space environment, and excavating using a novel vacuum technique. The 1.2m x 1.2 m x 8.5m deep shaft was required for installation of a hydraulic piston for a show lift. The project called for very accurate drilling through inter-bedded sandstone and siltstone within the water table. Development of a unique blast design was required for blast vibration control on a historic structure located just 15.8 meters away. The shaft was successfully completed without damage to any of the surrounding structures.

Jan 1, 2004

By Cesar Guerra, Alejandro Rojas, Dr. Jhon Silva, Luis Velasquez

The ANN method is applied to predict the P_80 size in one open pit gold mine in Peru. The ANN was implemented in Matlab programming language, and the results from the ANN are compared with data obtained using photo-fragmentation analysis software.

Feb 1, 2020

By N. Skopak, C. Aimone-Martin, J. Redyke, B. O. Meins

PipeBlast is a spreadsheet-based calculator based on research conducted by Southwest Research Institute (SwRI), used by the pipeline industry to determine if proposed blasting planned near existing pipelines can be safely executed. The two factors determining “safe” are blast-induced pipe wall hoop stresses and predicted peak particle velocity (PPV) at the pipeline. Although methodology used to predict hoop stresses is somewhat sound, predicted PPV amplitudes are highly exaggerated based on inappropriate attenuation models developed using spherical explosive charges of limited charge weights, placed in soil adjacent to model pipelines that do not represent rock blasting. Hence, pipeline companies readily reject well-design blasts and limit scaled distances far beyond what is reasonable and cost-effective to pipeline owners. Full-scale trench blasting in rock was conducted near a 24in (711mm) diameter operating API 5L X70 grade steel pipeline in Texas to compare PipeBlast model predictions with a Ground Strain Model (GSM) based on field measurements of ground motions on the surface and at the pipeline springline. Results of the GSM were compared with pipeline strains measured using wire gauges mounted on the Springline. The comparative results showed that a site-specific velocity propagation model provided good estimates of ground strains that are replicated on the pipeline walls in terms of hoop and longitudinal strains. Trench blasting 28ft (8.5m) from the pipeline produced ground motions of 7.6in/s (193mm/s). At this ground motion amplitude, the factor of safety defined as the allowable stress divided by the combined operating and blasting hoop stresses was reduce from 3.04 in the absence of blasting to 2.98. This paper explains the research and findings on which PipeBlast is based and presents an alternative approach to predicting blast-induced pipe wall stresses based on site-specific velocity propagation measurements and a ground strain model.

Jan 1, 2024

By Walter Valery, Sarma Kanchibotla

Due to the global financial crisis, the world economy has turned upside down and most major economies in the world are facing severe recession for the past one and half year. During this period most commodity prices have tumbled by more than half from their peaks and such a sudden and severe economic downturn is not seen since the great depression. This sudden drop in commodity prices and lack of credit made many mining operations unviable and even those mines that are marginally viable at this point are operating under severe cost pressures and capital expenditure restrictions.

Jan 1, 2010

By Robert B. Hopler

"The story of packaged explosives begins with the use of black powder (also called gunpowder) in mining. Although discovered in the 13th century, it was not until 1627 that the first records of use in mining is recorded. It took until the early 1800's before its use began in underground coal. Althougha free-running, granular material, its recommended (and safest) manner of use was for the miner to pour it into ready-made or onsite formed paper bags prior to insertion into the borehole. This was absolutely necessary in horizontal or upward-slanting holes."

Jan 1, 1991

By María Rocha, Benjamín Cebrián, Roberto Laredo

"Ring blasting designs have to achieve different goals in order to become efficient whether is done in up hole or downhole fashion. Ore recovery/dilution control, fragmentation and drift integrity all have to be taken into account when selecting parameters such as burden, spacing, linear explosive density and stemming. Blast energy simulation allows identifying contours of rock breakage and fragmentation, thuschoosing a combination of spacing at the end of holes and appropriate burden. Also, simulations are keyto concentrate energy levels on the mid part of the ring while making sure there is not too high of energy concentration around the drift, which integrity is needed for a safe ore mucking."

Jan 1, 2017

By John Vynne

BHP’s Navajo coal mine installed drill monitoring and high precision navigation systems on their three overburden drills during 2002 and 2003. Details of the DrillNav system hardware and reporting system will be discussed, as well as the significant benefits Navajo has achieved since the systems were installed. Navajo is not satisfied with the current results and plan additional upgrades to the systems. In addition, Navajo plan to integrate the data from their drill systems with data from other systems to achieve even greater increases in drill productivity and to reduce overall mining costs.

Jan 1, 2007

By Robert Hopler

After the disbanding of the Gunpowder Trust Association in 1904, the Association of Independent Powder and Dynamite Manufacturers was formed, followed in May of 1906 by the formation of the Association of Manufacturers of Powder and High Explosives. Due to a lack of success in attracting all manufacturers to membership, these organizations did not survive.

Jan 1, 2014

By Chanhwi Shin, Hyeongmin Kang

Mine optimization is a key strategy in the mining industry that focuses on improving the efficiency, productivity, and sustainability of mining operations. To achieve mine optimization, digitalization is essential for modernizing mining operations and attaining optimal performance. Due to the importance of mine digitalization, various software and platforms have been released to support this effort. Furthermore, by integrating these advanced technologies, mines can enhance processes, leading to significant economic and operational benefits. However, integrating data from various sources and collaborating across different platforms remains a significant challenge in the mining industry. Generally, data for mine optimization, such as mapping, smart drilling, FMS (Fleet Management Systems), fragmentation analysis, or vibration analysis, are collected and analyzed separately on different platforms. This separation makes it difficult to aggregate and utilize data comprehensively for overall mining process optimization. During the digitalization process, obstacles arise due to these complexity, variability, and sharing issues of data across different maker, sources, and methods. These challenges highlight the need for seamless integration to achieve optimal mining operations. Thus, this study applied a total solution that can cover the entire Drilling and Blasting (D&B) processes. The blast design was performed using actual terrain mapping data, and drilling and charging were conducted following a guide based on the blast design plan. After blasting, loading and hauling distances and fuel consumption were measured, and fragmentation for each blast was evaluated. All measurement tasks were automated to minimize human error. By collecting all data in one server, it became possible to perform an overall evaluation for each blast, allowing the identification of optimal values. In conclusion, to evaluate the optimization effects for each mining process, one month of integrated data collected on a single server was used. Compared to the period before the Total solution was implemented, there were notable improvements: a 25% enhancement in hole spacing, a 60% improvement in floor flatness, a 23% reduction in average fragment size, and a 19% improvement in fragment uniformity. Regarding cost savings per blasting volume, the improvements were 11.7% in drilling, 9.3% in explosives, 7.6% in loading, and 17.5% in hauling.

Jan 21, 2025

By Frederick B. Kuhnow

Harmonic energetic delamination a building is being considered for demolition at a formerly known atomic power lab. The building is within a containment structure under a negative pressure, so that no radioactive material is leaked out to the environment. A new approach was developed to make this work possible.

Feb 1, 2020

By Andrew Moore

It has long been common practice to conduct drilling and blasting operations at surface quarries in the Midwest in close proximity to near-vertical highwalls. The main reasons for such an approach, and the limited use of adequate safety controls, can be associated with higher costs, operational constraints, lithological requirements, property boundary restrictions, inadequate quarry planning, or a lack of understanding of highwall risks. Working in proximity to highwalls, without effective controls, exposes personnel and equipment to increased risk of incidents. In recent history, there have been isolated incidents involving equipment damage, or personnel injury/fatality around the United States. However, the Midwest market has largely escaped the effects of such incidents, even though the exposure rate is high. Awareness about this matter greatly increased on January 19th, 2021, when a significant incident occurred at a quarry near Green Bay, Wisconsin. As a crew was loading a typical blast near a highwall, a ground fall occurred, and multiple rock fragments struck a laborer working on the bench below. This individual sustained significant and life-altering injuries.

Feb 6, 2023