Search Documents

By Midori Sakamoto, Nobuaki Sakuma, Tsuyoshi Murashita

Recently, tunnel blasting works near the residential area and existing building are increasing and environmental problems caused by vibration have become serious public concern. In order to solve these problems, blasting works have been conducted with segmented blasting and reduce advance per round. However, with these blasting, work efficiency is not obtained, and regrettably the cost and risk of accident tend to increase. We developed a new controlled tunnel blasting technique with electronic delay detonator. Electronic delay detonator can supply extremely large range of delay period which could not be achieved with conventional pyrotechnical delay detonators. We utilized advantages in initiating hole by hole over entire tunnel face at the same round. Much seismic data obtained from tunnel blasting with conventional detonator was statistically analyzed in order to find average duration time of vibration caused by a single hole initiation. Numerical simulation using sample waves from a single hole initiation was carried out in order to find an optimum delay time which can separate vibration in each hole initiation and without decreasing blast performance. Trial blasting was conducted to examine the correctness of optimum delay time obtained from numerical simulation. This blasting technique was applied to an actual tunnel construction. This tunnel is 2 lane automobile tunnel with a total length of 659 meters and internal cross section of 70 square meters. The purpose of the use of blasting technique on occasion, was the protection of fresh water reservoirs directly above the tunnel, and to keep the effect on local private houses to a minimum. The vibration level against this station was limited under 20 mm/see P.V.V. With this blasting, the tunnel construction was completed without exceeding the limited vibration level, with minimum cost and construction time.

Jan 1, 1998

By Diego Quezada, Carlos Munoz, Marco Arellano

It is well-know that the presence of fine materials in mining has a direct impact on the plant processes with a great influence in the total amount of ore production and recovery. In Cu mining heap leaching is affected negatively by the presence of fines material (< 100 # Ty) in leaching piles, where a decreasing in Cu recovery is achieved in a lot of cases. D&B practices used normally in mine operations can generate fines > 4% in blasted piles, but the principal effects are reflected in the downstream processes where pre-conditioning post-blast materials release greater quantities of fines.

Jan 1, 2010

By Daniel Vargas Quispe, Yorhinio León Robles, Marco Jauregui Vargas, Helen Espinoza Bailon, Oshin Quispe Luya

This project describes the methodology applied during the execution of tests to determine the multiple controls that mitigate damage to the final walls of the pit. The different tests were executed on production pattern, which considered: modification of the angle of pre-split drill line, damage evaluation in individual drills with different load designs, varied detonation sequences, capture and analysis of elementary waves. After the evaluation and analysis of the results obtained in the tests, we are in process to standardize various damage controls such as; the combination of pre-split drill line angles at 80° and 90°; charge design in buffer drills that reduce the angle of action of the explosive and a detonation sequence that involves the creation of a relief filter that is made up of the detonation of two rows next to the pre-split drill line, which will have the function of filtering the waves of vibrations produced by the detonation of the production drills and at the same time it modifies the direction of damage towards the blasted material. The analysis of the different controls, as well as their combination, will allow us to improve the compliance results of the formation of benches.

Jan 21, 2025

By Alejandro Ferrada Vergara, María Jesús Barros Godoy

Reducing costs while maintaining productivity and achieving good results is a constant challenge in mining operations, especially in the drilling and blasting stage, since a bad blast can affect production plans, increase costs, affect safety and jeopardizing the pit stability. Examples of undesirable blasting effects are: flyrocks, boulders, loading equipment damages, lower production rates, etc. In some of the biggest open pit mines using conventional blasting patterns visited by the authors, the pattern does not adjust properly to the rock mass, in most cases blasting polygons are large and the rock mass condition is variable within the designed blasting pattern. On the other hand, conventional blasting patterns with stemming columns use 40-50% of the blast hole with inert material (the stemming). Moreover, blasting engineers spend efforts to improve fragmentation results by increasing explosive charge in spite of having the negative effect of ground vibrations, with little or no success. The classic approach is "the more explosive in, the better the fragmentation is", furthermore it is assumed this relation is direct and infinite, but it is definitely wrong. This work challenges the notion of a limitless direct relationship between explosive charge and fragmentation, this means this is partially true but just up to a certain limit. In other words, there is still room to improve energy distribution among the classical blasting techniques without increasing the explosive energy by using air decks. In the work to be presented air decks are built using conical shaped stemming plugs called Paraplug®. The results obtained suggests a wedge effect acts in the bottom of the stemming column that cushions the shock wave and the air deck to reduce the detonation pressure (this is due to the decoupling factor resulted from the air deck). The demonstration shows improvements in fragmentation results, reduced vibration records accompanied with lower dust column and costs savings in explosive charge.

Jan 21, 2025

By Kinross Paracatu, Victor Morais, Luis Marinho, Rolando Fuentes, Lucas Steffen, Leopoldo Muñoz, Washington Vilas

Nowadays, mining operations close to communities face increasingly challenges, especially in their drilling and blasting operations. One of the critical effects are the ground vibrations produced in its surroundings. The impact on the community must be minimized to guarantee the license to operate and, on the other hand, costs must be optimized, and an adequate fragmentation must be achieved to ensure the efficiency of subsequent processes and, consequently, to give sustainability to the business. In this regard, it is necessary that some controlled blasting technique to be performed and the utilization of advanced vibrations models. Currently, it is common in the industry either use of the double decking technique, where very low explosive charges are applied, making it necessary to use smaller drill patterns in order to keep powder factor as per design, which strongly increases the demand for drilling and a consequent impact negative on costs.

Feb 6, 2023

By Francisco Sena Leite, Raquel Sobral, Vinicius Gouveia de Miranda, Céu Jesus

"This document investigates a newly developed technique with the objective of improving terrain triangulation models (horizontal/sub-horizontal and vertical/sub-vertical terrains), mainly blast free faces. The algorithm uses multi-linear regressions to generate the best point cloud projection plane by applying the residues modulus minimization so as to create the finest 3D triangulation model. A change of base is required to create a new set of coordinate axis and generate completely new projection planes. The projection plane residue analysis is inferred in order to avoid or reduce the outlier points. The dataset is composed of 12 terrain models obtained from photogrammetry and a 3D Laser equipment thatgenerates georeferenced cloud points. This new technique is validated by the analysis of the obtainedcritical burden by the improvement of the general aspect view of the terrains and the capacity of outlier’s detection. The result and the quality of the algorithm demonstrates the improvement in the triangulation mesh, reducing errors in the calculation of over/under burden, free face volumes, cavities and, therefore, in the estimations of clearance/safety distances."

Jan 1, 2017

By Michael Laing

"Geology plays a critical role in many aspects of blasting, from fragmentation to wall control. One often overlooked component of blasting concerns blast results due to the effect of geologic features. The direction of blasting, with respect to strike and dip, can produce varied results, depending on thescenario. Working with geological features, as opposed to against them or without regard to them, can therefore dramatically improve blasting results. This paper focuses on the role of “geologic features”, which include joint-sets, natural fractures, and bedding planes (all of which are commonly referred to as “seams”) for the purposes of this paper. The goal of this paper is to promote understanding and mitigation techniques for various scenarios in which there are identifiable geologic features. Depending on the nature of these features (strike and dip specifically), blast design and pit advancement/development can be carefully considered to use make the best use of these features and optimize blast results."

Jan 1, 2016

By Johan Finsteen Gjodvad, Mathias Jern

The paper is part of the ongoing work of the Environmental committee of EFEE. To assist the European experts working with explosives one of the aims is to improve the common knowledge of similarities and differences between national legislation, standards or guidelines on vibration monitoring and other environmental monitoring during blasting in Europe and abroad.

Feb 1, 2020

By Johan Finsteen Gjødvad, Mathias Jern

The paper is part of the ongoing work of the Environmental committee of EFEE. To assist the European experts working with explosives one of the aims is to improve the common knowledge of similarities and differences between national legislation, standards or guidelines on vibration monitoring and other environmental monitoring during blasting in Europe and abroad. This has been done by use of an online survey through the most of 2018. Questions have been raised on vibration monitoring during blasting. The existence of norms, guidelines or standards and how they are used. Even though the questions have been kept at a high level they are formed to try to map the different national standards use of such things as frequency, guidance on monitoring position, distinction between different types of structures, requirement to the equipment and more. Furthermore a few initial questions have been raised on other environmental monitoring relevant for blasting. The respondents are national, cooperate or individual members of EFEE. The answers are experts in the use of explosives and vibration-monitoring in their respective countries. More than 60 have answered the questionnaire from 29 different countries. Mainly European as well as other nations including India, Israel, Nigeria, Saudi Arabia, UAE, USA, Greenland and Hong Kong. By analysing the incoming answers, the differences and similarities in vibration monitoring of the respondents has been clarified and mapped. Where possible other environmental monitoring has also been analysed. Where needed the different guidelines, standards and regulations have been visited to verify the answers and further elaborate on the comparison.

By B Mohanty

Several parameters such as, Energy, Strength, Brisance, Impulse, and Bubble Energy, are in common use in the explosives industry today to rate commercial explosives in terms of blasting performance. However, this multiplicity of terms, their frequent interchange and their purported one-to-one correlation with expected performance have given rise to a considerable amount of confusion, and have often resulted in unrealistic rating of explosives. In this paper, various theoretical and experimental methods of estimating energy and performance of explosives are discussed and their relative merits examined. These methods include, Computer Code Calculations, Cylinder Test, Trauzl Test, Ballistic Mortar Test, Underwater Test and Model-scale blasting. It is shown, in the light of actual blasting process, that such measures cannot be considered accurate indicators of expected blasting performance as the properties of rock to be blasted are either totally ignored or only partially accounted for in these methods. It is also shown that no single technique alone among those currently employed by the explosives industry can lead to realistic rating of explosives in terms of expected blast results. The need for the adoption of a two-tier rating system, one based on chemical potential "energy", and the other based on blasting "performance" is proposed, and specific approaches to achieve this objective are outlined.

Jan 1, 1981

By Michael A. Barbaglia, Mark William Withey

The lift shot is an essential blast design in the execution of mine creation and expansion plans. Whether it be opening a new quarry, creating a new level in an existing operation, or for control of water, lift shots are utilized to create the desired results. Lift shots by their nature differ from conventional production blasts because they have no free faces for relief of the blast. Due to this fully confined state, the primary direction of the rock movement is vertical, and the potential for excessive vibration and fly rock generation is great.

Jan 1, 1994

By Miguel Araos

The aim of this study was to understand clearly how VOD of emulsion-based gassed explosives is influenced by parameters such as nitrate salt composition in the oxidizing phase, product density, blend composition, gassing rate, type of sensitization, etc. Also some VOD testing was performed on watergel-based gassed explosives in order to compare the results with those obtained for emulsions. VOD measurements were conducted in the surface blasting facility at the Research and Development laboratory of ENAEX SA (Calama, Chile). Despite the fact that the influences of some parameters on VOD of emulsion-based gassed explosives are easily predicted, there was found to be an unexpected correlation. Although it is commonly believed that the VOD of gassed explosives depends on the density, this study found that the VOD depends on the both size and the amount of gas bubbles incorporated into the product as well as type of sensitisation, regardless of whether the explosive was straight emulsion or a blend. Density is just a consequence of the incorporation of voids into the explosive. Future work in this area may examine variation of other parameters, in order to obtain a greater knowledge of detonation properties and therefore to design more efficient explosives.

Jan 1, 2002

By Francisco Leite, Tomi Kouvonen, Bianca Saraiva, Vinicius Miranda, Auã Oliveira

One of the main challenges facing mining engineers is to draw up a plan that can be implemented in a timely manner, taking into account the operational variability of the mine’s production processes. These plans are often drawn up based on deterministic modelling (provided there are a set of known inputs that will result in a single set of outputs), when in truth we are talking about stochastic events (the cycles involved behave like random variables and their nature may be studied and reproduced). The result of using this kind of methodology can lead to non-optimized intuitive choices, which may harm the long-term targets defined by the planning team. Based on this principle, this document investigates the simulation of the rock fragmentation process in an open pit mine to assess the stochastic behavior of the loading and haulage operating cycles. The data assessed by the simulation process were the total costs of these operations in function of the powder factor. Based on a sample set data items, it was possible to check the probability distribution of the event as a Poisson distribution, applied to the loading and haulage cycles. The simulation consists of the repeated sequenced reproduction of these events (Monte Carlo simulation), in order to find the configuration that best fits the loading and haulage operations. By integrating these systems, it was possible to better understand the influence of the blasting in these operations, and as such to reduce the associated costs.

Feb 6, 2023

Drilling through unconsolidated material I need to drill blastholes through a mix of consolidated and unconsolidated material. This material is hung up in an underground ore pass. The total length of the holes would be approximately 200 feet. We have attempted to drill through the material with conventional ITH drilling, but were unsuccessful. Does anyone have a suggestion? I am more than willing to bring in a contractor to do the job, if they have solid experience with this type of problem.

Jan 1, 2011

By Isaac E. "Chip" Harris

A general understanding is given to how and where blast hole drills are used and what recent developments have taken place with small and large diameter drill hole machines. Indications are that new developments with high penetration rates and large diameter holes are not necessarily the answer to increased production in the field.

Jan 1, 1979

By Michael A. Peltier, Dennis V. D'Andreal, Larry R. Fletcher

Accident data obtained from the Mine Safety and Health Administration (MSHA) were analyzed by the Bureau of Mines to determine the most frequent causes of blasting accidents in U.S. mining and to examine trends in blasting accidents. This accident analysis is an update of a similar blasting accident study conducted by the Bureau and published in 1983. The analysis shows that there has been a recent reduction in mine blasting accidents: The annual average number of nonfatal injuries has decreased from 107 for 1978-81 to 46 for 1982-85. The annual average number of fatal injuries was reduced from 11.3 to 5.0 during that time.

Jan 1, 1987

By R L. Keller

Hong Kong has some of the most restrictive practices regarding blasting than any place in the world. Regulations regarding vibration limitations are 1 in/sec for structures and 0.5 in/sec (or even less) for most utilities; with no recognition of frequency response or adjustment. The Hong Kong Geotechnical Engineering Office has one of the most conservative approaches and protective guidelines for pre-blast assessment of slopes subjected to blast vibration (SEE paper '96). The protective measures to control flyrock generally required by the Mines Division are additionally very stringent. It is not uncommon for the costs associated with protective measures or methods which must be employed to exceed the cost of the drilling and blasting itself - or to waiver blasting application unfeasible altogether. From these restrictions it can easily be imagined how blasting in this urban environment would be most challenging.

Jan 1, 1997

By T. Bajpayee, G. Mowrey, D. Ingram, T. Rehak

Blasting operations are an essential element in the recovery of our Nation’s mineral resources. The mining industry uses billions of pounds of explosives annually. The majority of blasting occurs in surface mining .operations. Blasting results in the fragmentation and often the projection of rocks. Frequently, the rocks are thrown beyond the expected limits. Flyrock and failure to secure the blasting area dominate blasting-related accidents in mining, especially in surface mining.

Jan 1, 2001

By C W. "Mickey" Bradley

Thunder strikes terror in the hearts of man and has since the advent of time. We all fear the unknown; even the Greeks created a god, THOR, to be responsible for the thunder and rain. Thunder, by itself, can't hurt anyone; it is simply hot air moving very fast. Thunder, however, is caused by lightning and lightning is what we need to fear and rightfully so. Annually, lightning kills hundreds of Americans, injures another 2,000, damages or destroys approximately 30,000 structures, 1 starts thousands of forest fires and strikes mine properties over 100,000 times.

Jan 1, 1992

By Per-Anders Persson

This chapter deals with the concepts of shock wave8 and detonation wavea together, because a detonation wave is really a shock wave, supported by the explosive reaction that the shock wave ignites and propagates as it travels through the explosive material. In the context of rock blasting, furthermore, there is justification for treating shock waves and detonation waves together, because the mechanical effect of the detonation in an explosive in a drillhole in rock is propagated and its effects are spread throughout the surrounding rock by means of a shock wave. The overall performance of an explosive in rock blasting or any other application is of course dependent on how much thermal energy is released in the chemical reaction that occurs when the material detonates, and on how much useful mechanical work the reaction products can do as they expand. A major portion of thii chapter deals with the prediction and measurement of explosive performance, a subject which is now still in a process of rapid development.

Jan 1, 1998