Search Documents

By L. Gutierrez, M. Jeldres, R. J. Jeldres

"Clays are present in a large number of mineral deposits and are commonly found as gangue. Its complex chemical structure, characterised by anisotropic surfaces, makes its presence a permanent challenge for flotation operations, increasing the reagent consumption, decreasing the quality of the concentrate, and changing the rheological properties of the system. In this context, the main objective of this research is to improve the floatability of chalcopyrite minerals in the presence of clays by using guar gum, a low molecular weight organic polymer, which acts as a surface coating agent for clays. Clay Minerals Society provided the kaolinite sample and the chalcopyrite sample was purified from mineralized rock specimens obtained from Ward’s Natural Science Establishment. Micro flotation tests were carried out in a 150 cm3 Partridge-Smith cell, using compressed air as the gas phase at a flow rate of 80 cm3/min. Potassium amyl xanthate (PAX) and methyl isobutyl carbinol (MIBC) were used as a collector and a frother, respectively. The results showed that the use of guar gum improves the recovery of chalcopyrite in the presence of kaolinite because it induces the formation of clay aggregates that settle by gravitational effects, preventing the 'coating effect' and decreasing excessive collector consumption. pH played a key role in the guar gum performance, which was most effective at highly alkaline conditions (pH 11), where the copper recovery improved from 73% to 90%. The work has significant implications for the mineral flotation in the presence of clay minerals.INTRODUCTION The mining industry is continuously confronted with challenges that alert the sustainability of the sector. There is little availability of water, the grade of the deposits are getting smaller, and the gangue is becoming more complex. Usually, clays are part of the gangue in numerous systems, including copper ore, porphyry, nickel, platinum, etc. (Senior & Thomas, 2005). The structure is mainly composed of layers of tetrahedral silica (T) and octahedral alumina (O) that join in certain proportions: 1: 1 (T-O) and 2: 1 (T-O-T) (Theng, 2012). Also, they expose two crystallographically different surfaces: the faces, which tend to be negatively charged, and the edges, which carry a charge that changes from positive to negative depending on the pH (Van Olphen, 1977). One of the most common clays in copper deposits is kaolinite, whose structure is composed of an octahedral sheet of gibbsite bound to a tetrahedral silica sheet in the ratio 1:1"

Jan 1, 2018

By G. V. Sedelnikova

Biohydrometallurgical studies were performed on the sulfide gold-arsenic concentrate obtained in treatment of refractory ore from a deposit located in northern Russia. Gold is disseminated in sulfides-arsenopyrite, pyrite and antimonite (their content is 10.0%, 30.4% and 0.7%, respectively). Gold extraction is only 11.8% by cyanidation. Results are given for test bacterial oxidation of the concentrate in continuous mode at temp. = 28~32°C using mesophilic bacteria and at temp. = 32~38°C using the association including moderate thermophilic bacteria. The paper shows that the use of moderate thermophilic bacteria allows to speed up sulfide biooxidation and reduce its time to 96 hours compared to leaching at temp. = 28~32°C for 110~120 hours. The optimal range of pH = 1.5~2.0 of biooxidation process was determined where bacterial solutions are produced with the molar ratio Fe:As > 3 necessary for precipitation of hard-to-solve, environmentally safe arsenical precipitates. Electron microscopy showed that sulfide biooxidation results in liberation of disseminated gold with nanoparticle-level sizes. High sorptive activity of carbonaceous matter and other compounds of bacterial residues cause low gold extraction into cyanide solution ? 28.7%. 10% resin load makes it possible to extract 88.1% Au. Aeration of pulp in calcareous medium enhances extraction to 95.7% and decreases cyanide consumption from 17kg/t to 8 kg/t.

Jan 1, 2014

By Ventsislav Stoilov, Angel Angelov, Ivan Korolev, Antti Remes, Todor Pukov, Stoyan Gaydardzhiev

"The process modeling and simulation studies aim for better process operation and favorable environmental impact. The objective of this work is to set up a simulation model of the Assarel copper flotation circuit for planning and optimization of the process with the aim of increased metal recovery. The model is parameterized based on laboratory flotation tests of ore samples from the Assarel mine together with mineralogical studies by X-ray diffraction (XRD) and Mineral Liberation Analysis (MLA). A combination of several techniques allows reliable identification of mineralogical composition of the selected samples. The changes in the proportion between sulfide minerals in various products along the circuit have been also documented. Further, this information is used in the simulation model and in data reconciliation procedures for establishing mass balance. The simulation accuracy is studied by comparing the simulations with the plant survey based mass balance. Constructed simulation model can be used to run alternative process scenarios. As an example, the flotation circuit performance with different reagent regimes is simulated based on data from batch flotation tests. Two reagents were considered for this purpose, dithiocarbamate-based one and xanthogen formate/mercaptan blend. It has been revealed that these reagents do not have the same influence on the selective flotation. The one improves flotation of gold and overall recovery but without notable selective action. In contrast, the other showed better selectivity towards copper, rejecting more gangue and lowering gold recovery. The model is also applicable for process optimization studies with different feed compositions, flowrates and circuit configurations. INTRODUCTION In the pursuit for elevated technological indicators, finding an optimal set of process parameters fully utilizing the potential of the equipment is a key factor to success. Over the past decades, there has been a substantial development in flotation circuit optimization through performance benchmarking using metallurgical modelling and steady-state computer simulation. Practical simulation engineering tools are based on experimental data obtained from laboratory tests and from plant surveys and operation data. With the help of flotation models, it is possible to study grade-recovery response with different feed compositions and throughputs, and with various cell-operating parameters, as well as to evaluate and design different flowsheet configurations. Outotec’s HSC Chemistry® software, which incorporates simulation and mass balancing modules alongside with several other tools, can assist with this optimization (Mattsson et al., 2015)."

Jan 1, 2018

By S. Gerl

Since Schönert, 1980 a multiplicity of scientists have dedicated themselves intensively to the scientific investigation of wet grinding in agitated media mills. The achieved research results led to a clearly improved understanding of the comminution mechanism in wet operated agitated media mills and in consequence also to clearly more efficient machines. In contrast to this the standard of knowledge on dry grinding in agitated media mills is still very small. The practical experience from numerous plants shows however that the transferability of knowledge from wet grinding to the dry grinding regarding transport phenomena and comminution behaviour, influence of the operating parameters and also wear is very limited. In the industrial application above all the continuous mode of operation is preferred. The main problem which has to be solved in agitated media mills is minor the comminution itself, than rather the question of the trouble free material supply and material extraction as well as the cooling of the mill. The agitated media mill MaxxMill® offers an innovative concept to overcome the feeding and extraction problem with its rotating grinding chamber, the eccentrically mounted agitators as well as the eccentric flow deflector with integrated material supply. Because of the pneumatic extraction of the ground materi-al cooling of the milling chamber is not necessary. On a MaxxMill ® laboratory mill with a 5 litre grinding chamber volume extensive parameter studies were carried out to study the influence of operating parameters on the continuous dry grinding of quartz sand. The test were performed in a continuous single pass operation without classification of the final product. Apart from the influence of the throughput rate on fineness above all the influence of the agitator and grinding chamber speed as well as the grinding media size was examined.

Jan 1, 2014

By M. Kanuchová, J. Briancin, M. Achimovicová

"Faculty of Mining, Ecology, Process Control and Geotechnology, Technical University, Košice, Slovakia An industrial eccentric vibratory mill was used for direct and short-time mechanochemical reduction of ilmenite concentrate (FeTiO3) and anatase (TiO2) with magnesium metal powder in order to reduce Fe and Ti resp. and hereby to convert them to the more soluble phases suitable for further hydrometallurgical processing. X-ray diffraction analysis of FeTiO3 after 60 min of milling with Mg confirmed the presence of Fe0 and Mg2TiO4 phases and for TiO2 after 180 min of milling the new TiO and MgO phases have appeared. X-ray photoelectron spectroscopy has detected Fe0 (metal) and Mg2+ species which are corresponding to the product of FeTiO3 mechanochemical reduction. The product of TiO2 mechanochemical reduction has revealed XPS spectral lines corresponding to Ti2+, Ti4+ and Mg2+ species on its surface. Morphology of mechanochemically reduced samples was studied by scanning electron microscopy analysis. Subsequent leaching of mechanochemically reduced FeTiO3 and TiO2 was performed in dilute HCl and H2SO4 at 80oC and compared with mechanically activated samples. The recovery of Ti has reached 100% for FeTiO3 and 79% for TiO2 after 60 min of leaching. Based on this study the flowsheet for possible processing of natural refractory titanium ores patented by author was adapted and documented. INTRODUCTION Ilmenite (FeTiO3), along with rutile (TiO2) represents the most important titanium resource necessary for titanium industry, for production of titanium metal, alloys and pigment grade TiO2 which are becoming more important and versatile for various industries such as an aircraft and aerospace, navy, chemical, automotive, medical and offshore wind industries, for machine and plant engineering and architecture as well, mainly due to high corrosion resistance. Pigment grade TiO2 is utilizing in pigment, plastic, glass, paper and rubber industries (Zhang, 2011). There are obvious research efforts for development of the potential alternatives to the expensive thermo-chemical commercial processes of titanium raw materials processing. Zhang (2011) has summarized conventional thermo- a electrochemical processes which involved a combination of pyrometallurgical, hydrometallurgical and electrometallurgical technologies and highlighted the improved hydrometallurgical routes promising for commercial application in the future. Such improvement could also be mechanical activation of FeTiO3, TiO2 by high-energy milling which causes their structural disordering, the changes of physical and chemical properties, consequently and has a positive effect on the dissolution kinetics (Achimovicová et al., 2014a, 2017, Baláž, 2008). The various types of mills such as a planetary ball mill, a vertical ball mill, a drum mill, an attritor were used for mechanical activation of FeTiO3 as a pretreatment process for subsequent leaching (Achimovicová et al., 2014)."

Jan 1, 2018

By S. Narra

The importance of bio-products production is enhanced with the abundance and renewability of ligno- cellulosic biomass in comparison to the depleting fossil fuels especially in producing environment friendly energy. Lignin is obtained as a sludge residue from the pulp and paper industries as well as from the bio- ethanol /bio-gas production plants. Lignin is a renewable fuel with a high heating value equivalent to anthracite coal, low ash content and hydrophobic properties. The extracted lignin in paper and pulp mills is usually burnt at the mill directly to cover the energy production costs of the mill. The efficient utilization of lignin can reduce the percentage of lignin sludge used for energy production in comparison to the present situation. Presently the lignin is burnt /incinerated as sludge with minimum of 30 to 50 % moisture content. This high moisture content reduces the energy efficiency and simultaneously utilizes more amount of lignin sludge in producing the required energy. This paper explains a possibility of integrating sludge-pelleting techniques in paper and pulp mills. The integrated sludge-pelleting techniques would lead to an optimal utilization of lignin for energy and would simultaneously save the lignin resource for material utilization. The sludge pelleting process solves also the problem of handling, storage and explosion risks of lignin when compared to the present situation.

Sep 1, 2012

By L. Gutierrez, R. Yepsen, F. Alarcón

Chile is the world's largest copper producer which is mostly in the form of sulfides for which froth flotation is the most efficient concentration process. As a result a concentrate that contains high concentrations of copper sulfides such as chalcopyrite, chalcocite and enargite is obtained. In the last decades processing of ores containing high concentrations of enargite (Cu3AsS4) has continuously increased in Chile, which is related to the fact that ore deposits nawadays are more heterogeneous and complex. Enargite is a mineral that contains arsenic and its presence in the copper concentrates implies severe penalties. In addition, the shortage of fresh water has driven the search for new alternative sources of water, among which seawater has proved to be one of the most attractive. The objective of this research is to study the behavior of the enargite in the process of flotation using seawater, and at the same time to compare its behavior with the results obtained using conventional water. The study was carried thorugh micro-flotation tests using pure samples of enargite, at pH values ranging from 4 to 11, both in fresh and seawater. PAX and MIBC were used as collector and frother respectively. Micro-flotation tests were also done at different redox potential conditions so that the effect of the surface oxidation of enargite was evaluated in seawater. The results indicate that the recovery of copper from enargite is reduced in seawater compared to fresh water, in particular at the pH values close to those of the formation of the first hydroxy complexes of Mg and Ca. In general, the experimental data indicate that the floatability of enargite is strongly affected when seawater is used, in particular at oxidizing conditions. These results suggest that Mg2+ and Ca2+ ions contained in seawater interact with the surface of enargite forming hydrophilic species.

Jan 1, 2018

By Heikki Häkkänen, Tommi Kauppinen, Navid Khajehzadeh

"There are a variety of methods suitable to analyse elemental and mineralogical contents of rock drill core samples. Current demands are on fast exploration and objective analysis of ore samples. This paper proposes a combination of Laser-Induced Fluorescence (LIF) and image processing, entitled LIF-imaging, as a potential method for automated mineral analysis of the drill core samples. It is shown that LIF-imaging can produce a mineral map of the fluorescent minerals existing on the surface of the drill core samples. The test cases are drill core samples from a Ni-Cu mine situated in Kevitsa, Finland. The main prerequisite of LIF-imaging technique is a reference data, linking colours to the minerals. This study describes the calibration of LIF-imaging technique using precise but slow Raman spectroscopy. Using regularized logistic regression, a model is obtained that classifies the minerals based on their emitted fluorescent colours in the digital images. The abundance of each mineral group is estimated by pixel counting. The results are compared with X-Ray Diffraction laboratory assays performed on the same samples. The results show that the interpretation of the fluorescent minerals through LIF images corresponds to the XRD results. Furthermore, the utilization of the logistic regression to interpret the existing fluorescent minerals greatly improves the technique."

Jan 1, 2014

By L. O. Filipov, N. E. Menad, A. Geneyton

"Zeta potential of synthetic monazites presenting various compositions were measured to investigate the effect of the main lanthanides substitutions on electrophoretic mobility and resulting IEP. The measurements are performed in a CO2 depleted and enriched solutions showing both reduced influence of monazite chemistry and strong influence of ions resulting from the solubilization and dissociation of CO2. The influence of oleic acid on the electrophoretic mobility of those monazites was also investigated. The influence of pH on oleate adsorption was studied using a bubble/particle adhesion system. Adhesion strength measurements were performed on pure synthetic monazite-(Ce) and monazite-(La). An extensive thermodynamic model of monazite in water was developed to highlight correlations between lanthanides hydroxides/carbonates species concentrations in the bulk solution and oleate adsorption. Based on electrophoretic measurements, advanced thermodynamic consideration and adhesion measurements, further details of the oleate adsorption model on monazite surface were proposed.INTRODUCTION Electrophoretic and potentiometric data on monazite and, a fortiori, other rare earth semi-soluble salts such as bastnaesite are extremely erratic (Chelgani et al. 2015). The isoelectric points measured with electrophoretic mobility methods range from 4.7 to 6.5 although sporadic data indicates an IEP (isoelectric point) far from that range. Different explanations are proposed in the literature to explain the IEP variability notably the numerous chemical substitutions that frequently occurred within monazite crystal lattice (Chelgani et al. 2015). Based on lanthanides speciation diagram, several authors highlighted the influence of specific lanthanide species on the flotation performance of rare earth semi-soluble salts when carboxylate or hydroxamate collectors are used. Although lanthanides ions have a great affinity for carbonates groups (Kragten et Decnop-Weever 1987), lanthanide (hydrogen) carbonates were not implemented in speciation diagrams. In this work, an advanced thermodynamic model is proposed to highlight correlation between flotation performance and lanthanide species predominance but also concentrations. Qualitative measurement of the monazite surface hydrophobicity are performed through tests of adhesion of coarse monazite particles onto bubbles. Since flotation and microflotation technics are highly influenced by hydrodynamic parameters, this method was investigated to obtain a sharp contrast between appropriate and inappropriate pH conditions. This paper is to investigate 1) the effect of lanthanides substitution on monazite surface properties through zeta potential measurements, 2) the mechanism of adsorption of carboxylates on monazite surfaces and 3) the effect of CO2 on monazite surface properties and carboxylates adsorption."

Jan 1, 2018

By Ruiyang Zhang, Ping Fang, Dezhou Wei, Shuling Gao

A CFD based numerical simulation of flow characteristics of hydrocyclone was conducted with different structural and operational parameters to investigate its distribution characteristics and influencing mechanism. The results show there exist several unsymmetrical envelopes of equal vertical velocities among both upward inner flows and downward outer flows in the hydrocyclone, and cone angle and apex diameter have remarkable influence on the vertical location of the cone bottom of the envelop of zero vertical velocity. It is also found that some tangential velocity isolines exist in the horizontal planes located in the effective separation region of hydrocyclone, and feed pressure has almost no effect on the distribution characteristics of both vertical velocity and tangential velocity of flow in hydrocyclone, however the magnitude and gradient of tangential velocity are made increased obviously, so as to make the high density particles motion velocity to the wall increased and to make the cyclonic separation effect improved. The simulation results also show when the apex diameter increased, the pressure of the fluid field decreased, however the pressure grads in the apex district increased, and the degree of changing is different as the cone angle, which showed some interactive influence of cone angle and apex diameter on the fluid field of hydrocyclone. While the feed pressure also has almost no effect on the pressure distribution characteristics, however the its magnitude and gradient are made increased accordingly, which can improve the separation accuracy according to particle density.

Jan 1, 2014

By Lucy van de Ruit, Megan Becker, Aubrey Mainza, Jenny Wiese

"UG2 chromitite ore is a complex, highly disseminated platinum ore from the Bushveld Complex in South Africa, with typical platinum group mineral (PGM) grain sizes below 15µm. The introduction of stirred mills to the platinum industry has enabled grinding to finer product sizes, which has improved liberation and recovery of the finely grained PGMs. However, reduction in particle size leads to an increase in chromite entrainment in the flotation concentrate, which has a negative impact on the subsequent smelting process. Factors such as particle size, froth structure, solids concentration and water recovery have all been identified as impacting entrainment, but whether particle shape also has a significant effect is unclear. The purpose of this study was to determine whether the recovery of chromite particles by entrainment during the flotation of UG2 ore is affected by particle morphology. A laboratory vertical stirred mill with inert ceramic media was used for grinding UG2 ore which was then floated in a batch flotation cell. Flotation feed and concentrate samples were analyzed using QEMSCAN to quantify the angularity and aspect ratio distributions of the particles. The stirred mill product was found to have relatively broad aspect ratio and angularity distributions, with the major mineral components (chromite and silicates) having very similar shape characteristics. Analysis of flotation feed and concentrate samples suggested that particle shape does not have a significant effect on chromite entrainment."

Jan 1, 2014

By Diego Mesa, Willy Kracht

Frothers may be classified as weak or strong depending on their ability to produce stable froths, which is related to the amount of water that they transfer from the pulp to the froth. They can also have an effect on the non-selective mechanism of recovery by entrainment, implying that both selectivity and froth stability are, at least to some extent, frother dependent. Solids, on the other hand, also have an effect on froth behaviour. Clays, which are characterized by their small particle size, laminar shape, and high specific surface, tend to report to the froth phase and have an enormous impact on both froth stability and the overall performance of the flotation process. The purpose of this work is to shed light on the effect that different frothers have on the froth behaviour when clays are present. In order to do that, two sets of experiments were conducted using frothers from the families of alcohols and polyglycols. For each test, the equilibrium froth height was measured at different frother concentrations in an agitated machine with an acrylic square-base cell that was 11 cm wide and 25 cm high. The cell was designed in such a way that froth was able to grow without concentrate discharge. In the first set of tests, pure clays such as kaolinite and montmorillonite were used. In the second set, an actual copper sulphide ore with a high content of clays was used as solid phase. The results, expressed as curves of equilibrium froth height against frother dosage, showed a coupled effect of frother-clay on froth behaviour for both sets of experiments. In some cases, the froth grew up until the border of the cell with only a few parts per million of frother. In other cases, the equilibrium froth height varied smoothly with frother dosage. The results suggest that choosing the right frother can be of use for controlling the froth behaviour when dealing with clay-rich froths, using frother dosage as the control variable. The application of these findings at industrial scale are discussed and some recommendations are given.

Jan 1, 2018

By M. Niinae

Electrokinetic soil remediation by electroosmosis and ionic migration is restricted to soluble sub-stances. At a higher pH, the soil particles sorb more heavy metals, such as cadmium, than at a lower pH and the precipitation reactions of heavy metals are promoted. Both mechanisms make heavy metals immobile, rendering clean up more difficult and electrokinetic extraction inefficient. There-fore, the acidification of soils is very important to increase the clean up efficiencies of heavy metals, such as cadmium by electrokinetic method from contaminated soils. In the present study, acidification of soils and cadmium transport are predicted with a numerical method in which electrical flow is coupled with hydraulic flow, and the sorption process in the soils is induced in the model. The effects of some factors such as electrode configuration, electric field strength and electrode spacing for saturated soils are investigated using this numerical model. The results obtained this study are summarized as follows: The two-dimensional electrode configurations containing cathode surrounded by three or more anodes rapidly acidify the soils and remove cadmium from soils compared with one-dimensional electrode configuration. However, two-dimensional electrode configurations develop spots of inactive electric field between cathodes. A larger electrode spacing increases the processing time required, and it was also found that a larger electric field strength reduced the processing time required.

Jan 1, 2014

By J. Leite

In a small-scale mining in Brazil?s northeast, scheelite were exploited since 1940?s using a traditional gravity concentration flowchart (composed by jigs and shacking tables) that operates with low efficient for fine particles. Tailing of this plant was submitted to chemical, mineralogical and size characterization. Results pointed 50% smaller than 74µm with a grade of 0.11% WO3. The particle?s size is an important operational variable to heighten recuperation by shacking tables. Tests using Falcon SB40 centrifuge concentrators and shacking table were realized, optimizing their operational variables. Based on the tests results a new flowchart was proposed for concentrating and tailings recovery.

Sep 1, 2012

By Morin D. H., Battaglia-Brunet F., D'Hugues P.

"In the mineral-processing field, bioleaching of metal sulphide concentrates is currently operated in very large mechanically agitated tanks. Such bioreactors have considerable requirements in terms of power consumption for mixing, aeration and heat transfer. The use of slurry bubble column, where the particles are suspended by gas motion as well as by liquid upward flow, could be an alternative to achieve bioleaching in more economical conditions. In order to compare these two techniques, a unit of stirred reactors in cascade and a bubble column were comparatively operated at laboratory scale in the bioleaching of a pyrite concentrate. For both pieces of equipment, experiments were performed not only in batch mode but also in continuous conditions.Bubble column performances were significantly affected by unpredictable technical difficulties met to maintain continuous feeding in the bubble column and by a significant settling of the heavy solid particles. Nonetheless, theoretical kinetic data, extrapolated from results in batch conditions, could be compared to those obtained in continuous tests, in bubble column and in mechanically agitated reactors. These kinetic data were used to evaluate the influence of reactor design and configuration choice on bioleaching performances."

Jan 1, 2003

By F. Henríquez

Traditionally, the implementation of an automated control for a ball mill has been a challenging one. First, it must be capable of processing a variable SAG mill feed while at the same time avoiding to become a process bottle neck. Second thing is, it must deliver an adequate quality product (P80) to the process downstream. Then the ball mill itself and its associated classification equipment has problems of its own: it must maintain adequate control of cyclone?s pressure, density and pump-box level with often, less manipulated variables than needed, namely, variable pump speed and the opening/closing of cyclones. Thus, it becomes a non-linear multi-variable type of process with often too multiple and contradictory control objectives to satisfy simultaneously. On top of that, to extend cyclones availability and yet, maintaining their performance, is must both for process and maintenance purposes. Trying to solve the puzzle, Minera Los Pelambres implemented a novel and successful combination of MPC (Multivariable Predictive Control) and advanced control in two of its newest ball mills, reducing considerably process variability while maintaining high throughput and keeping the process well within constraints limits. Because of their differences in processing capacity, size and topology, two different stabilizing-control strategies were developed, tested and tuned. Hence, for both control approaches their implementation process, main results, areas of applicability, limitations and their key performance indicators are discussed further. This paper also discusses the need of such advance control technologies in the mining industry, including the impact of these technologies on best practices for their implementation, operation and long term sustainability

Sep 1, 2012

In the present work, the influence of coagulant, polymeric flocculant structure type and mode of addition on flocculation performance and dewatering behaviour of plant mineral waste tailings of diverse mineralogy (kaolin, quartz, goethite/hematite feldspar, gibbsite, rutile, and Illite) is investigated. High molecular weight, non-ionic polyacrylamide homopolymer and anionic (acrylate) and cationic (quaternary acrylate) copolymers were used in orthokinetic flocculation of colloidal-ly-stable, aqueous dispersion of negatively charged particles. It is demonstrated that, through prudent selection and mode of addition of polymer structure types, synergistic effect between certain cationic and anionic flocculants can be readily achieved, leading to significantly improved dewaterability of the heterogeneous mineral waste tailings.

Jan 1, 2014

By Tchingis Lekhatinov, Lev Filippov, Vyacheslav Severov, Alexandre Matinin, Victor Samyguin, Inna Filippova

"Comparison of flotation efficiency of the new multi-zone flotation cell (MZFC) and different conventional cells was carried out at lab and pilot scales on the various samples: high contrast pyrite tailings and old copper containing tailings. MZFC is a cell of intensive flotation, which provides optimal hydrodynamic conditions for all flotation sub processes. Enhancing of particle attachment, creation of conditions for coalescent flotation, selection of spatially separated zones according to optimal hydrodynamic conditions for flotation sub-processes are proposed as main principles to design an MZFC. The bubbles/pulp stratification was pointed out as a limiting step in the existing intensive flotation machines. Two strategies to improve bubbles/pulp stratification in the MZFC were studied: (a) impact of pulp-bubble jet to the surface of a prismatic insert inside of cell, which provides the detachment of low hydrophobic particles from bubbles, and (b) profiling the pulp/bubbles jet from the reactors due to a specific geometry of cell walls. The new continuous MZFC devices were demonstrated similar or higher efficiency in comparison with laboratory batch flotation cells for pyrite flotation. Higher flotation efficiency (82%) with pure pyrite concentrate (51.2% of sulfur) and a recovery level of 92% was obtained in MZFC when the cell with stratification by impact was used. Similar results were obtained with old Cu-containing tailings. Although MZFC had 1.5 times greater yields of concentrate than a batch flotation cell, it provided the increase of chalcopyrite recovery by 29.4% and concentrate grade by 4.8%. An original organization of pulp/bubbles stratification in the separator part of the new intensive flotation machine using variable geometry inserts allowed the best flotation selectivity with a bubble mineral loading coefficient 1.5 fold higher than the laboratory mechanical or pilot cells."

Jan 1, 2014

By Ghislain Bournival, Seher Ata, Graeme J. Jameson

A common method to prevent bubbles from coalescing in a flotation cell is by the addition of surfactants, called frothers. The gas dispersion properties in a column were tested for solutions of 1-pentanol, tri(propylene glycol) methyl ether, and poly(propylene glycol) in the presence of sodium chloride. The dependency of surfactant on the gas holdup can be divided into regions. It seemed that for a sufficiently low concentration of surfactant, even a stronger surfactant could show a transition in gas holdup from constant/decreasing to increasing with concentration. This region, however, was not marked by a decrease in the average bubble size. In addition, PPG gave higher gas holdup values while averaging larger bubbles. On the other hand, sodium chloride mostly affected the gas holdup when the concentration was high enough to prevent bubble coalescence. Another parameter affecting the gas holdup was the superficial gas velocity. A linear dependency was found between the two under a bubbly flow regime. The current study showed that both surfactants and salt could slightly affect the influence of the superficial gas velocity on the gas holdup.

Jan 1, 2014

By Heiko Schiemann, Christoph Beyer, Thomas Pretz

"Due to multiple experiences in the field of planning and engineering of processing plants for secondary materials the Chair for Processing and Recycling of Solid Waste Materials decided to develop a software tool that supports the engineering and the planning of the basic layout of processing plants for secondary material flows. The detailed description of the material flow and its characteristic parameters is one of the main tasks to be worked out and should be considered as the basis for representative simulation results.The description of the material flow and its characteristic parameters is based on a fraction vector containing 12 material fractions. This is a compromise between a detailed material flow description and a compact and therefore time-extensive calculation model. Each material fraction is characterized by 15 parameters, which can be edited with the help of an easily accessible user-interface. In addition to basic parameters like ignition loss, water content and calorific value more parameters like the material fraction-specific particle-size distribution are contained. Using the model library SimuRec, the processing success and the recovery of complex processing plants for secondary materials can be predicted."

Jan 1, 2003