Search Documents

By J-P Franzidis, P. O. Gyebi

"Coal-water mixtures (CWM) of concentrated fine coal may be transported in pipelines but this is influenced by both CWM rheology and stability. Here, a low viscosity is required to reduce power requirements, as well as good stability for transport and storage. The objectives of this study are to investigate the importance of surface charge, solids concentration and dispersant addition on the rheology and stability of a fine Witbank coal-water mixture (<75 m). Zeta potential, rheology and stability were measured with a Malvern Zetasizer, a AR1500EA rheometer and a static rod penetration test, respectively. Sendep 30D, Sendep 30F and Norilose 8058, all supplied by Senmin International, were used as dispersants, at dosages of between 0.1 to 0.5% dry coal (w/w). Solids concentration was varied from 10 to 58% (w/w). The zeta potential was found to be positive at low pH and decreased sharply with increasing pH to a minimum of -50 mV at pH 10. The zeta potential decreased with increasing dispersant concentration for all dispersants. The lowest zeta potential of -63 mV was obtained for Norilose 8058 at a dosage of 0.3%. CWM rheology was Newtonian at lower solids concentrations but became non-Newtonian at solids concentrations over 40% (w/w), with an initial yield stress and pseudo plastic behavior. The yield stress decreased sharply with increasing dispersant concentration for all dispersants. The lowest yield stress was obtained for Norilose 8058. The addition of dispersants resulted in significant improvements in stability. A penetration ratio of over 70% was obtained for Norilose 8058 after 10 days. In summary, the addition of dispersants resulted in a decrease in the zeta potential which increased the electrostatic repulsive forces between particles, thus improving both CWM rheology and static stability.INTRODUCTION Coal Water Mixtures South Africa’s energy economy depends heavily on coal. It accounts for about 70% of primary energy consumption, 93% of electricity generation and 30% of liquid petroleum fuels (Eberhard, 2011). The transportation of coal to export markets and power generation stations is a problem in the South African coal industry due to ageing and inefficient rail infrastructure. This problem is intensified by the long distance of coal haulage, delays in the time required to load and unload wagons, and environmental challenges related to air pollution and water contamination. Fine coal may be transported more efficiently and economically in a pipeline as a highly concentrated coal water mixture (CWM). Typically a fine coal CWM will contain 60-75% coal, 25-40% water and nearly 1% of dispersing additives (Atesok et al., 2005; Dincer et al., 2003). However, the transport of CWMs in pipelines is strongly influenced by both CWM rheology and stability. Here, a low viscosity is required to reduce power requirements, as well as good stability for transport and storage. These quantities are affected by the coal composition/mineralogy, solids concentration, particle size and size distribution, particle shape, inter-particle forces and dispersant type and dosage (Laskowski, 2001)."

Jan 1, 2018

By Kazimierz Trybalski

"Simulation methods have a big potential in the studies and analyses of complex technological processes and schemes. The simulation method used jointly with flow diagrams and related transmittance models allows describing and analysing dynamic characteristics.The paper presents results of simulation analysis of dynamic characteristics of ore dressing system, called closed circuit mill-classifier-mill. Such systems are widely used in ore processing plants. The system was analysed as a typical system with material feedback, to establish its dynamic characteristics.Flow diagram conforming to the technological scheme is presented in a figure. Transmittances shown in the scheme are defined as follows:GMP - transmittance of rod mill,GP, KZ, GW, KZ - transmittances of overflow and underflow streams of spiral classifier, respectively,GMK - transmittance of ball mill,GT - transmittance of underflow stream from classifier to ball mill,GU, MP, GU, MK - fraction transmittance of outflow streams of rod and ball mill, respectively, summed up at classifier input.Taking into account, in base of carried out analysis the transmittance forms of individual system elements. The calculations are based on numeral forms of transmittances of individual blocks, defined through industrial experimentation.Step input function to rod mill was assumed to be a step of mass ore flow rate to the mill. Responses are defined as product densities.This figure demonstrates the way of input signal transmission by consecutive elements of the system and shape of these elements' responses. It can be noticed that step signal undergoes gradual change from the stream of the first order to those of higher and higher orders as a distance from process leading edge increases. Simultaneously, the impulse signal is subject to systematic smoothing and decay. From the technological point of view, the most important is response stream in point 5 (on the above figure) that characterises classifier overflow, which is a final product of this system."

Jan 1, 2003

By Xiaoping Xu, Tiansong Dong, Guosheng Wang

"Jianfengpo tin ore is located in Jiangxi Province, China. The cassiterite is fine and dispersed. It is hard to separate marmatite from a variety of sulfide minerals. Because the iron-containing sulfide minerals including pyrrhotite, pyrite and chalcopyrite are detrimental to the improvement of the grade of zinc concentrate. Besides, the presence of the iron oxides and ferro-carbonate minerals results in the difficult beneficiation of tin. Therefore, Jianfengpo tin ore is a kind of refractory cassiterite polymetallic sulfide ore. According to the properties of Jianfengpo tin ore, the technology process of "Sulphide ore preflotation-Bulk flotation of sulphur and zinc-Separation of sulphur and zinc -Magnetic separation-Gravity concentration" was developed to recover the valuable materials including marmatite, pyrite, magnetite, cassiterite and indium comprehensively. For the feed ore containing 0.87% Sn and 0.70% Zn, a zinc concentrate of 44.56% Zn with a recovery of 69.10%, a high-grade tin concentrate of 54.38% Sn with a recovery of 53.03% and a low-grade tin concentrate of 6.54% Sn with a recovery of 1.25% can be achieved in the batch flotation tests. In the industrial tests, for the feeding which contains 0.55% Sn and 0.65% Zn, the tin concentrate of 49.10% Sn with a recovery of 48.52% as well as the zinc concentrate of 45.11% Zn with a recovery of 60.10% can be produced. Thus some pyrite and magnetite concentrate are recovered as well. So Zinc, tin, sulphur and iron ores are recovered effectively by the technology."

Jan 1, 2014

By T. Fujita

A high-grade fluorite ore is converted into hydrogen fluoride to produce many kinds of materials containing fluorine. Recently, it is becoming necessary to use low-grade fluorite ore due to the depletion of high grade ore. The low-grade fluorites usually have impurities such as SiO2, P, CaCO3 and arsenic. The most impurities such as SiO2, CaCO3 and P can be removed by using flotation method. However, the removal of arsenic is difficult, and the arsenic contamination decreases the hydrogen fluoride production percentage. The novel technologies for processing low-grade fluorite ore are urgently needed, in order to lower the arsenic concentration to less than 100 mg/kg. In this study, the removal of arsenic from low-grade fluorite ore has been investigated by means of an autogenous grinding using tower mill in sulfuric acid aqueous solution and 0.3 mm zirconia balls in water. The nano grinding in water can prevent the dissolution of 0.3 mm size zirconia balls as grinding media by sulfuric acid solution. Experimental results showed that the arsenic concentration was reduced from 260 mg/kg to 90 mg/kg and CaF2 recovery reached 90% by this process.

Sep 1, 2012

By Graeme Jameson

"In current flotation circuits it is customary to grind the whole of the mill feed to an initial size, which is determined by the liberation characteristics of the ore, and the ability of the flotation machines to float the fully liberated particles. Usually, the product of the primary mill will be ground further in a ball mill, to improve the liberation of the values and hence the product grade, before passing to rougher flotation cells. The final grind size is ore-dependent, and is a balance of factors including the relation between surface liberation and grind size, the grain size of the valuable particles within the host rock, and the feed grade. The P80 for the feed to flotation may be as high as 300 µm for free-milling copper ores, and as low as 53 µm for finely disseminated complex ores. The grinding of the feed ore requires considerable input of energy. The rate of replacement of wear components such as mill liners and media, is proportional to the energy input. The costs of these two factors - energy and wear - are usually comparable and together they form the major part of the running costs of a concentrator, and indeed, of the whole mining operation. The energy required increases as the final grind size decreases. This talk will focus on the reduction of milling costs that could be achieved, using a fluidized bed flotation technology that can give high recoveries at coarse particle sizes. A number of different circuit designs will be presented, using the new technology. Calculations show that reductions in the running costs of a mine and associated concentrator of the order of ten to twenty percent could be achieved."

Jan 1, 2014

By Willis Forsling, Prabhakar Swarna, Hanumantha Rao Kota

"The solubility of wollastonite and its Hallimond flotation behavior as a function of dodecylamine concentration and pH are examined. The flotation response is characterized by adsorption and surface energy in the presence of amine. The methods of UV-Visible and FT-IR spectroscopy for adsorption and sessile-drop contact angle for surface energy estimation are employed.The results of wollastonite dissolution clearly showed its non uniform dissolution. The surfaces are depleted with calcium ions and became rich in silicon within 10 min of flotation time. Maximum flotation of wollastonite corresponds to a half monolayer coverage of amine, which is substantiated by the surface energy parameters as shown in figure 1."

Jan 1, 2003

By M. Pischtschan, S. Belz, M. Perrucci

In High Pressure Grinding Rolls (HPGR), the material grinding takes place between the fixed and floating rollers. In this regard, the rollers start to wear over a period of time, which is impacted by for e.g.: ore characteristics, operating pressure, feed material size and non-uniform feed presentation across the roller width. HPGR operational experiences have shown that the rollers do not wear at the same rate. This differential wear rate over time leads to differences in the tangential speeds of the rollers, causing an uneven gap between the fixed and floating rollers in relation to the material. This unwanted but extremely common situation results in a less effective grinding process due to the fact that the slip between rollers is not optimal. As the rollers wear profile increases, the roller with smaller diameter starts to wear further, deteriorating the comminution efficiency up to a point where operators have to stop the HPGR to replace the rollers. Since the wear rate of the rollers is not equal, the replacement of the same cannot be properly planned so that their life-time are fully utilized. In this paper, a dynamic load share control with the use of ABB’s variable speed drive system is proposed, which provides the possibility to the HPGR operator to impact the roller wear in such a way that it equalizes the wear rate to a certain extent and extends the roller life time. Called RollXtend™, this solution includes a load share factor which can be parameterized based on the wear measurement performed manually during maintenance procedure. Additionally, this paper describes an automated load sharing concept based on a non-invasive wear measurement method. The partial results of the technology trial in a copper/gold mine are presented, which aimed at detecting stud damage and estimating the real rollers profile throughout their life time. The final objective of the pilot project was reduce the amount of planned and unplanned downtimes of the HPGR by increasing the rollers life time and avoiding catastrophic stud damages.

Jan 1, 2018

By A. J. Lynch, L. Ergun, M. Oner

"A research program on modelling cement grinding circuits has been in operation at Hacettepe University, Ankara, for four years. It has concentrated so far on tube mill and air separator grinding circuits for cement clinker, with emphasis on plant sampling surveys, including axial sampling inside the tube mills. The methodology is to use plant data to build the models and to supplement this by laboratory data where necessary, for example the determination of breakage functions. The plant data come from comprehensive sampling surveys and so far 33 surveys of clinker grinding circuits have been carried out in 9 plants. The operating conditions have been• mill sizes – 3.2 to 4.8 metres diameter and 8.5 to 15 metres long,• mill feed rates – 46 to 158 tonnes per hour,• air flow through mills – 25000 to 125000 cubic metres per hour,• cement clinker work indexes – 10.3 to 18,• separator sizes – 2. to 3.1 metres diameter,• separator feed rates – 132 to 689 tonnes per hour,• separator speeds – 12.3 to 21 metres per second.The ball mill model is Whiten’s perfect mixing model and the separator model is the Tromp curve with a fish-hook. This paper emphasises on the importance of calculating the breakage rates and the discharge functions with three case studies at five different circuits which were selected for discussion because they show how particular features of circuit operation can be included in the general models. Size distributiongraphs are used to illustrate every aspect of the discussion.In case I the special emphasis on calculating the breakage rates and discharge rates separately is given in a high pressure grinding roll-ball mill-separator circuit. The tonnes of each size fraction in the mill and the calculated values of R/D, D and R are determined. The values of R per mw are also given to allow comparison with mills of other sizes. The circuit allows the comparison of the static type (V Sep) and dynamic type separators (SKS). Comparing the reduced efficiencies shows that the dynamic separator is slightly more efficient than the static one.In case 2 data are given from two compartment tube mills having the same diameter and the motor power but different ball size gradation. The breakage rate particle size variation of the second chamber of two mills indicate that having finer ball size distribution causes higher breakage rate values."

Jan 1, 2003

By P. Somasundaran, Tarun Bhambhani, D. R. Nagaraj, P. Patra

"Certain non-sulfide gangue minerals are known to have a detrimental impact on flotation performance. When present in large amounts, they can negatively affect recoveries, grades and throughput at current operations, and dictate the viability and economics of a greenfield project. While the problem has been investigated for a long period of time, a scientific understanding of the mechanisms by which these minerals affect performance has not been obtained, and no acceptable solutions have been developed. This study focused on the role of physical aspects (e.g. shape, size and morphology) of these minerals as the underlying factors for poor performance. Flotation tests were conducted using model mineral systems to understand the impact of one phyllosilicate mineral (muscovite) on flotation kinetics, recoveries and grades. The study reveals that there is minimal impact on flotation kinetics, no impact on recoveries, but a very strong detrimental impact on concentrate grade. The traditional mechanisms of transport such as true flotation and entrainment are not sufficient in describing the extent of transport. The transport is attributed to the unique platy morphology of muscovite, which allows for action of buoyancy forces. Data also shows that the muscovite transport to the froth phase depends on particle size; coarser sized muscovite (100-150@) report to the froth phase in much larger amounts than medium sized muscovite (50-100@). At finer size fractions (<50@) the transport is also increased, and this is likely due to entrainment."

Jan 1, 2014

By P. Gao, J. W. Yu

"Magnetizing roasting-magnetic separation is an important route for the beneficiation of refractory iron ores. In this investigation, a pilot-scale fluidized magnetizing roasting reactor was introduced and used to study the effects of roasting temperature and the flow rates of reducing gas CO and fluidizing gas N2, on the magnetizing roasting performance of an Anshan-type carbonate-bearing fine iron ore. The results showed that the hematite was almost reduced to magnetite by a gas mixture of 4 m3/h CO and 1 m3/h N2 at a roasting temperature of 540 °C. Under the optimized conditions, a high-grade magnetic concentrate assaying 66.1 wt.% Fe with a recovery rate of 91.2% was achieved from an Anshan-type carbonate-bearing fine iron ore assaying 42.0 wt.% Fe. The XRD, VSM, and optical microscopy analyses revealed that the siderite was successfully converted to magnetite by roasting. Some coarse hematite particles were difficult to reduce to magnetite completely; however, these generated magnetite particles with a fine hematite core could also be effectively recovered by magnetic separation after liberation from gangue minerals due to their strong magnetism. INTRODUCTION Magnetizing roasting followed by low-intensity magnetic separation has been considered as an effective solution, both technologically and economically, when upgrading refractory iron ores (Zhang et al., 2012; Peng et al., 2012; Li and Zhu, 2012). According to the type of roasting reactor, the magnetization roasting can be divided into shaft furnace roasting, rotary kiln roasting, and fluidized bed roasting (Zhu and Li, 2014).Shaft furnace magnetization roasting system is mainly composed of heating and reduction processes. The hematite ore is first heated to 700~800 °C in the heating zone, then falls into reduction zone where the weakly magnetic hematite is reduced to magnetite by coke oven gas at 550~600 °C (Yan et al., 2012). However, several years of engineering practices indicate that the shaft furnace can only process the hematite ores with a granularity of 15 ~75 mm, and the shaft furnace roasting is also characterized by heterogeneity of roasted product. Hence, the shaft furnace magnetization roasting technology is gradually replaced by high-gradient magnetic separation with the development of high-gradient magnetic separator. The rotary kiln generally handles the hematite ores with a grain size of less than 30 mm (Zhu and Li, 2014), however the formation of clinker ring in the rotary kiln will affect the yield of iron resource. In the fluidized bed furnace, the hematite ore is shaken up by an upward current of gas which maintains the individual particles in suspension (Yu et al., 2018). The precise adjustment of the gas velocity to the particle size and the specific weight of the hematite ore, make it possible to generate a floating mixture of gas and solids which behaves almost like a liquid (Yu et al., 2017a). The process is reported to have the following advantages over the other roasting techniques: ease of control due to absence of moving parts within the reactor, homogeneity of roasted products, ability to handle fine particles, and high efficiency of heat transfer and mass transfer (Li et al., 2015; Yu et al., 2017b). However, the simultaneous heating and reductive magnetization of hematite ore occur at the same place in the conventional fluidized bed reactor. Therefore, the reductive atmosphere, as well as the safety and stability of anti-explosion are hard to be controlled. Besides, the roasting temperature for conventional fluidized bed furnace is usually up to 950~1150 °C (Liu et al., 2017). Thus, the formation of clinker ring caused by high temperature will affect the operating efficiency."

Jan 1, 2018

By Rintaro Hayashi

The enrichment of useful components from ores and/or wastes has become important with increasing recent worldwide resources demand and the amount of wastes generated from the urban mines, in order to establish real ?sound resource-cycle society? including the activity of resource exploitation. The first stage of the treatment in the process must be comminution and it is important to make good liberation among compositional phases in the targeted resources. Electrical disintegration (ED) is well known to make a selective breakage at phase boundary. However, the detailed mechanism of the phenomena is not clarified yet, in especial, on the influence of electrical properties of compositional materials on the liberation. This paper made a comparison between the liberation degrees of ED products and the results of electromagnetic field analysis using finite element method (FEM). In the experiments, we used several synthetic cement paste based samples in which mineral particles were dispersed to apply the ED, and in the electromagnetic field analysis, we calculated the charge density accumulated and the Maxwell stress at phase boundary. It was found, for highly insulating mineral samples, that higher breakdown voltage was necessary because electric charge was not easily accumulated at phase boundary but that higher liberation degree was obtained after the breakdown (ED). It was also found the tendency that higher liberation was observed for the samples which had higher maximum Maxwell stress calculated by the electromagnetic field analysis. From the results, the electrical charge and Maxwell stress induced at phase boundary could be driving forces of selective breakage. In addition, we also applied the ED to the printed circuit boards (PCBs) in order to concentrate miner rare metals, which were essential for producing electronic devices. It could be demonstrated that the devices installed on the PCB were easily detached from the board and that most of metal elements in the devices was exposed and liberated from the insulating plastic covers, which were broken in the ED, then, it is considered that the subsequent solid phase separation could be effective for concentrating such metal elements. Keywords: liberation, electromagnetic field analysis, printed circuit board, miner rare metal

Sep 1, 2012

By Y. E. Brylyakov, M. A. Kostrova

"The apatite staffelite ores (ASO) of Kovdor deposit are dominated by fine-grained aggregates containing both phosphate minerals and silicates — vermiculite, smectites, zeolites. These minerals exhibit ion-exchange properties. In this connection, the magnitude of cation exchange, along with the content of P2O5 and CO2, is an important property of apatite staffelite ore, which largely determines the performance of concentration processes. In the examined ASO samples, the magnitude of cation exchange measured in terms of Ca2+ is 2546-4790 g/ton. The conducted laboratory studies of apatite staffelite ores with various mineral composition showed that adding calcined soda improves the recovery of P2O5 into the flotation concentrate. Full-scale tests were conducted at the apatite staffelite ore processing plant at Kovdor Mining and Concentration Operation and demonstrated the high performance of the proposed agent treatment. The test results showed that in the flotation of apatite staffelite ores, the optimum calcined soda feed rates range from 3,500 to 5,000 g/ton of the flotation feed. With close flotation feed and concentrate grade parameters, the P2O5 recovery gain is 17%. The effect of adding soda is associated with the desorption of the hardness cations from the minerals, precipitation in the pulp and, accordingly, improvement in the ionic composition of the liquid phase of the flotation feed due to a reduced content of calcium ions. Based on the test results, the proposed agent treatment with an elevated feed rate of calcined soda was implemented at Kovdor Mining and Concentration Operation in the flotation of apatite staffelite ore. The apatite staffelite ores (ASO) of Kovdor deposit are dominated by fine-grained aggregates containing both phosphate minerals and silicates — vermiculite, smectites, zeolites. These minerals exhibit ion-exchange properties. These minerals have certain properties requiring a more detailed examination for a better understanding of the flotation properties of apatite staffelite ores."

Jan 1, 2018

By Grigori I. Voiloshnikov

"The long-term studies on development of the technology for precious metals recovery using activated carbons executed by Irkutsk Research Institute of Precious and Rare Metals and Diamonds (IRGIREDMET) were finished by successful introduction of ""Carbon-In-Pulp"" process in Russia (1984).The review of some studies, accompanied by development, testing, introduction and subsequent improvement of considered technology, carried out by IRGIREDMET is submitted in this paper.The basic regularities of gold and silver adsorption onto activated carbons from cyanide, thiourea, chloride and other solutions are investigated using various phisical-and-chemical methods ( X-ray photoelectron spectroscopy, Voltammetry, X-ray microanalysis etc.). Using voltammetry it was found that gold cyanide is adsorbed onto activated carbon without chemical changes and partial reduction of gold is possible only during drying of carbon samples before analysis. Metallic gold and silver may be dissolved in boiling cyanide solution at argon atmosphere when they are in contact with activated carbon surface. Gold adsorption mechanism for activated carbons has great differences from that for the ion exchange resins. So the most probable mechanism for gold adsorption from cyanide solution is adsorption of neutral molecules Me n+[Au(CN)2-]n.X-ray quantitative microanalysis technique was developed to investigate gold adsorption kinetics onto spherical activated carbon. Gold profiles in granules of activated carbon for various adsorption conditions were tested (carbon particle size, mixing efficiency, adsorption time etc.). Mathematical methods were used to determine gold diffusion coefficient within activated carbon granule.The properties of various types domestic and foreign activated carbons were tested and the demands to activated carbons suitable for gold extraction were determined. As a result foreign and Russian activated carbons AG-90, AG-95 were recommended for use at Russian gold plants. Domestic adsorbents are cheaper in comparison with foreign activated carbons. The methods to restore carbon adsorption activity including acid treatment and thermal reactivation were tested and implemented."

Jan 1, 2003

By Alexander E. Sobolev

The kinetics of oxidative dissolution of lead sulfide in solutions of nitric acid and sodium hypochlorite was studied using the rotating disk method and the factor experiment design. The dependences of the PbS dissolution rate on concentration of oxidant (HNO3 or NaOCl), temperature, disk rotation frequency, and duration of interaction were determined. The adequate kinetic models allowing calculating the specific dissolution rate at any combination of values of the influencing factors were obtained. As a result of the complex analysis of kinetic parameters, the modes of the each process proceeding were established, their macromechanisms were determined, and the limiting stages of the oxidative dissolution processes were revealed. The dissolution kinetics of lead sulfide in solutions of nitric acid was found to have several regimes. At HNO3 concentrations below 0.5 mol/L, the process proceeds in a mixed mode close to a diffusion-controlled. It is caused by low oxidative activity of HNO3 and considerable diffusional diffuculties at this acid concentration range. At the nitric acid concentrations more than 0.5 mol/L and less than 6.0 mol/L, the process was found to be kinetically controlled. The limiting stage of the interaction is the surface chemical reaction. The observed relatively high order of the dissolution rate with respect to the concentration of HNO3 was explained by the autocatalytic action of the acid reduction products. At nitric acid concentrations exceeding 6 mol/L, the process proceeds in a mixed mode close to a diffusion-controlled, and the dissolution rate sharply decreased that was explained by a decrease in the solubility of reaction products. When lead sulfide is dissolved in sodium hypochlorite solutions, at first time the amount of PbS transferred into solution remains close to zero. Gradually, as time goes, this amount begins to increase sharply. The dissolution rate rises and reaches the maximum value, further remaining constant. At the steady-state regime, the dissolution rate is independent of the duration of interaction and disk rotation frequency. The process was found to be kinetically controlled. The limiting stage is likely to be chemical reaction on the surface of solid lead sulfide. The obtained kinetic characteristics enlarge the database on hydrochemical oxidation kinetics of sulfides and can be used for the elaboration of the recommendations for the effective comprehensive exploitation of lead-bearing ores and concentrates. Keywords: lead sulfide, nitric acid, sodium hypochlorite, hydrochemical oxidation, dissolution kinetics

Sep 1, 2012

By A. D. Shuloyakov, G. A. Finkelstein, V. I. Kurets, A. K. Vedin

"In disintegrating solid ores with mineral values disseminated in them, one of the principal tasks is to selectively separate valuable mineral particles from the matrix in which they reside, striving at the same time to keep their natural shape and size as intact as possible.The conventional mechanical disintegration methods do not meet this most important requirement in full. The other major objective here is to reduce electric power consumption during the fragmentation stage, since up to 65 per cent of the total power consumption at concentrators processing ores of non-ferrous, ferrous, rare, and precious metals is spent on disintegration steps.Numerous experiments conducted on dozens of ore types (tin, tungsten, and many others, as well as on rock containing diamonds, rubies, emeralds, etc.) have invariably demonstrated by far superior integrity of mineral values as compared with that obtained by mechanical as well as other types of disintegration.However, the process remains as power-intensive as ever which is due to the imperfect nature of the electro-technical devices that convert the network electric current into high-voltage electric impulses responsible for the disintegration process.The maximum capacity attained in disintegrating the hardest materials from 40 mm to 2 mm size in a single operating chamber with four high-voltage electrodes does not exceed 1.0-1.5 t/h. Attempts at increasing the number of electrodes and the capacity of the operating chamber have failed so far because of high overall dimensions and mass of the electrical part of the installation supplying the chamber with pulsating current, as well as of the commutation requirements. At the same time, a number of overseas operations have reported a significant breakthrough in their attempts to reduce dozens of times the overall dimensions and mass of the discharge impulse generating installation (EIS), which enables us to contemplate to increase the capacity of the EIS at least ten times in the nearest future. Yet, even with the currently achieved capacity of the EIS, these installations have found wide use in geological surveying, precious and semi-precious stones production, in grinding super hard materials, etc., since they provide spectacular selectivity of disintegration and thus the integrity of valuable mineral crystals."

Jan 1, 2003

By S. S. Indi, D. Santhiya, S. Subramanian, K. A. Natarajan

"With the gradual depletion of the high-grade ores and finer dissemination of values in the leaner samples, it has become imperative to develop innovative approaches to process such complex ores. The beneficiation of complex sulphide ores containing copper, lead and zinc minerals, remains one of the most important challenges in base metals metallurgy. The advent of biotechnology in mineral processing has opened up immense possibilities to exploit such difficult-to-treat ores. Bioprocessing techniques thus hold promise as potential substitutes for the conventional technologies in vogue. Several types of autotrophic and heterotrophic bacteria, fungi, algae and yeasts are implicated in mineral beneficiation processes. Adopting a bioprocessing route to mineral beneficiation has attractive benefits, such as lower cost and energy requirements, environmental acceptability and operational flexibility.The interaction of sphalerite- and galena-adapted Bacillus polymyxa (B. polymyxa) cells with sphalerite and galena has been investigated through adsorption, electrokinetic and flotation studies. The amount of sphalerite-adapted cells adsorbed onto sphalerite and galena is found to decrease with increase in pH. On the other hand, the adsorption density of galena-adapted cells onto galena shows a feeble maximum around pH 8, and the amount adsorbed is marginally higher in the pH range of 8 – 11.5. In the case of sphalerite the amount adsorbed is higher in the pH range of 5 to 7. The adsorption density of both the adapted cells is higher for galena vis-à-vis sphalerite. Electrokinetic studies indicate significant surface chemical changes on the chosen sulphide minerals and the bacterial cells, consequent to microbemineral interactions. Selective flotation tests on a synthetic mixture of galena and sphalerite confirm that sphalerite could be preferentially floated from galena, using galena-adapted cells, but not with the sphalerite-adapted cells. The cells adapted to galena assay a higher polysaccharide content and are more hydrophilic, while the sphalerite-adapted cells have a higher protein content and possess greater hydrophobicity. Transmission electron microscopic studies have provided evidence in support of the differences between the cell surface characteristics of sphalerite- and galenaadapted cells (Figure 1). Possible mechanisms of interaction between the minerals and the bacterial cells are discussed."

Jan 1, 2003

By Hiroshi Sasaki, Herman D. Mendoza

"The surface-chemical property of nickel slag fiber was modified in aqueous media in order to act as an active and efficient collector of colloidal amorphous silica from geothermal effluent. Colloidal amorphous silica (0.05 µm) from geothermal wastewater causes operational and ecological problems. It clogs geothermal pipes and waterways, and when disposed to the environment poses hazardous effects on both the flora and fauna ecology. Because colloidal amorphous silica is extremely fine and remains in suspension in aqueous media, conventional solid/liquid processes to remove colloidal silica from its bulk liquid are rendered ineffective.A rapid separation technique is then developed to remove effectively amorphous colloidal silica from its bulk liquid by attaching the extremely fine particles of silica onto a nickel slag fiber coated with magnesium hydroxide, Mg(OH)2. The nickel slag fiber has the following characteristics: a high surface area and predominantly possesses negative charge in aqueous media with an iso-electric point at pH ~2.5. When soaked and saturated with Mg(OH)2 solution, the surface of the nickel slag fiber becomes coated with fine and compacted Mg(OH)2 precipitates. This modifies the surface- chemical property of nickel slag fiber transforming the negatively charged surface into a positively charged surface in aqueous media with an iso-electric point of around pH 11.8, which corresponds to the iso-electric point of Mg(OH)2. When geothermal effluent containing negatively charged colloidal amorphous silica particles (i.e.p. of silica is pH 2) is passed through a column-bed packed with surface-chemically modified nickel slag fibers under natural pH conditions, the colloidal amorphous silica particles are recovered by attachment onto the surface of the surface- modified nickel slag fiber. The recovery of colloidal amorphous silica by attachment is 97-99%, resulting in the production of a relatively clean and silica free output. Aluminum hydroxide, Al(OH)3, was also used to modify the surface –chemical property of the nickel slag fiber. In the same way, it also exhibited a positive response with the collection of colloidal amorphous silica from its bulk liquid, but yielding a lower recovery of 90%. This may be attributed to the lower surface potential and iso-electric point of pH 9.3 for Al(OH)3. The separation process was evaluated and analysed using existing potential energy theories. Figure 1 shows a micrograph of the surface of an unmodified and the Al(OH)3 –modified surface of nickel slag fiber."

Jan 1, 2003

By P. M. Solozhenkin, V. P. Nebera, V. D. Skorohodov

"Aqueous dispersions of air specifically prepared on the basis of flotation reagent solution acquire active properties in relation to the solid surface and may be imply as a medium for flotation ores. Such aerated solutions were defined as Activated Aqueous Dispersions of Air (AADA) with 5-6:1 ratio and the procedure of mineral separation was defined as a flotation process under non-equilibrium conditions. These procedures differ from conventional flotation mainly in reagent interaction with minerals through their adsorption films on gas bubbles simultaneously forming flotation complexes. Gas-liquid mixture is kept till an adsorption layer of reagents close to the limit value is formed on the surface of bubbles. The theoretical basis of AADA is considered.The results of two-phase gas- liquid mixture (AADA) were studied. Two versions of AADA were considered. Electrical surface potential of the air bubbles with the surfactant film, untreated minerals particles in Coulomb attraction and flotation complex formation were analyzed. Special flotation machines were constructed for separation of mineral suspension in air dispersion, whose effectiveness was confirmed in flotation of apatite waste of Kovdor ore. FK-9 machine introduced on Kovdor iron ore combine for the recovery of apatite from current departures of factory. The froth product contained 7.2 % P2O5, with recovery of 44 % apatite, which was processed for getting melted phosphoric-magnesium fertilizers."

Jan 1, 2003

By H. Hamza, M. R. MacIver, M. Pawlik, L. Malin

"Size and shape are important properties of aggregates formed in engineering processes and natural systems. Measurement of aggregate size or shape is a challenge when the solids concentration is beyond the gel point, ?? > ??g, when the aggregates are in contact and it is difficult to distinguish or segment individual particles in the network. This paper describes the use of a micro-computed tomography (micro-CT) method for the calculation of the aggregate volume fraction, ??, and a characteristic aggregate length, ??a, based on a 3D chord length measurement algorithm. These parameters can be used to quantify changes in aggregate and pore size during a compressive yield stress test to help understand the impact of flocculation and network structure on dewatering. INTRODUCTION In a thickener, flocculation is often used as a pre-treatment step and the final solids content of the underflow depends on the network strength and permeability of the bed formed by settled aggregates (Usher, Spehar, and Scales 2009). This paper describes the measurement and analysis of micro-computed tomography (micro-CT) of flocculated mineral sediments to obtain a characteristic length, ??a, of the aggregate and pore phases during a staged compressive yield stress experiment. This parameter may be used as an indicator of changes in aggregate and pore size to quantify material behaviour in solid-liquid separation processes that depend on self-weight compression or applied pressure. This analysis was carried out to help understand the effect of flocculation on aggregate structure and the thickening process as part of a broader research on the improved solid liquid separation of tailings produced in the oil sands industry.Aggregate properties The solids phase of an aggregated or flocculated suspension will eventually settle – if left undisturbed – under the influence of gravity. As settling of a flocculated suspension continues, the solids volume concentration, ??, may increase to the gel point or gelation threshold (Landman and White 1994), ??g, above which the aggregates form a network of touching particles, or space-filling structure (Kranenburg 1994). In the sediment bed, the aggregates are surrounded by fluid and occupy a partial volume fraction, ??, according to"

Jan 1, 2018

By Markus A. Reuter, Jacques J. Eksteen

"The modelling of bath type furnaces tends to be either fundamental in nature or total empirical ""black box models"". While models of the first kind are robust, they tend to lack accuracy, in cases where they are to be used for process control, and may take an overly long in development time. On the other hand, black box models tend to lack robustness of prediction for all circumstances and tend to be limited to interpolate based on historical data. While this may very often provide short-term accuracy, the models may have problems with stability in the long term. Moreover, the model structure may not reflect any of the fundamental properties of the system and remains opaque to fundamental analysis. The aim of the model development is in obtaining a model that have robustness, high accuracy, a short development time and which is adaptive to a changing environment. The models are specifically developed for on-line decision support or control of furnaces. The modelling approach is evaluated for a chromite bath smelting furnace. The role of systems analysis, mass balance smoothing, thermodynamic analysis are integrated into one generic algorithm for bath type furnaces. Not only are fundamental process relationships such the mass and energy balances satisfied through a scientific method of data reconciliation; the proposed modelling approach allows adaptive prediction, the first step towards predictive control or metallurgical decision support.It is shown that neither an ARMAX model only, nor a purely equilibrium model only, could predict the dynamics of the process very well. However, a combination of the two approaches more than doubled the accuracy as measured by the R2. It was noted for carbon dissolved in the alloy, that the improvement in R2 in using a hybrid modelling approach was more than the sum of the R2 of the individual traditional approaches. Similar improvements in modelling performance were noted for all other species.It shows further that process dynamics may totally overshadow the effect of thermochemical equilibrium (even when the thermochemical equilibrium prediction includes the recycled alloy and slag heels as additional feeds). The exclusion of process dynamics therefore leads to erroneous results."

Jan 1, 2003