Search Documents

By Robert Fernie

Demographics and Infrastructure demands have led to a significant increase in construction of: deep basements for buildings and, trough structures for Highway and Rail/Metro. Concrete embedded walls used for temporary works can be incorporated into permanent works and because of this (and geological conditions) tend to be favoured in UK. This paper considers British practice in the provision of diaphragm (slurry) walls secant (true and pseudo) piled walls contiguous piled walls Plant utilisation, construction techniques, reinforcement placement, connections, propping, water tightness, tolerances, general UK practices and their relation to design practices are discussed. [ ]

Jan 1, 2000

By Eric M. Klein

As part of the Woodrow Wilson Replacement Bridge project several damaged wetland and environmental areas were to be mitigated. One of the mitigation projects consisted of constructing a Denil fish ladder around Peirce Mill Dam in Rock Creek National Park, Washington, D.C. The dam is a historic structure operated by the National Park Service. The fish ladder is located between the east abutment of the dam and Beach Drive, a major collector road. Construction of the fish ladder required removal of a portion of the east abutment and an excavation that extended about 22-ft below the pavement of Beach Ave. It was not possible to close Beach Drive except for very brief intervals or at night; therefore, a support of excavation system that would minimize disruption to the public was required. The high groundwater required that the groundwater be cut off prior to excavation; the random rubble and soil fill, and shallow but erratic rock surface precluded driving sheet piling. A jet grout system was selected because the grout probe could penetrate the rubble fill, stabilize a variety of soil conditions, and cut off the ground water prior to excavation. It was not possible to construct a stable wall without tiebacks or soil nails. Given the schedule and tight working conditions it was decided that soil nails through the jet grout wall facing would be the most cost effective method, as it did not reduce the working space as rakers would and would be more cost effective than prestressed tiebacks.

Jan 1, 2006

By Geoffrey C. Hebner

Augered, cast-in-place piles (ACIP) have become a very common foundation type in Atlanta and the Southern Piedmont Province as well as much of the United States in the past 20 years. Prior to the introduction of ACIP foundations in Atlanta, the most common deep foundation type was Raymond piles. Raymond piles are basically a driven, thin-walled step-tapered steel pile filled with concrete. Drilled piers were also relatively common and continue to be used, particularly in shallow bedrock or high column load situations. Driven piles, including pipes, H-sections, and timber piles were previously common with working loads typically in the 30 to 50-ton range. Initially, ACIP foundations had similar allowable capacities, however, over time improvements in installation techniques and equipment have resulted in an increase in allowable ACIP capacities. Correspondingly, they have become a more cost-effective and trusted foundation for geotechnical and structural engineers. Over the next several decades many other deep foundation alternatives began to lose popularity. ACIP are one of the predominant deep foundations in Atlanta and the Southern Piedmont today. Although ACIP foundations have widespread popularity in the private sector, they have not been readily accepted currently by government transportation agencies. ACIP may be used by some of the smaller municipalities, but to the author's knowledge, have not been used with regularity by larger, state agencies.

Jan 1, 2003

By Drew Floyd

Five full-scale pile load tests were performed on pairs of PZ-22 sheet piles installed with a vibratory pile driving hammer. The sheet piling was installed in several locations in soil generally consisting of miscellaneous granular fills overlying soft organic silts, inorganic silt interbedded with sands and gravels, very dense glacial till and shale bedrock. The test program also included the use of tip tell tales to determine what capacity could be attributed to tip resistance and skin friction. During the design phase of the project, it was assumed that the capacity of the sheet piles driven with the vibratory hammer could be correlated with the rate of penetration. The correlation between vertical capacity and rate of penetration would be used as a basis for determination of a driving criteria from driving the production sheet piling. The sheet piling load tests demonstrated that it was not possible to correlate the capacity of sheet piling driven with a vibratory hammer and the rate of penetration. It was also demonstrated that the capacity of the sheet piles was directly related to the density of the soil at or just below the tip. The results also tend to agree with empirical equations provided by Meyerhof (1976).

Jan 1, 1989

By Michal Topolnicki

"Discussed is the use of wet Deep Soil Mixing, generally executed with single mixing tools 0.8 to 1.6m in diameter, employed in the foundation of viaduct supports. The applications involve economical patterns of ground improvement, covering in average about 40% of the foundation area or less, which contribute to the competitiveness of DSM solutions when compared to traditional piling. The focus is on selected aspects of the geotechnical design, applicable for geo-composite systems in which the interaction between the stabilised and the native soil should also be considered. Evaluation of settlement can be carried out with simplified methods, accounting for punching effects, or with more advanced FE models in case foundation tilt or differential settlements become important. Potential bending of DSM columns should be considered when evaluating column stresses, especially when dealing with deep deposits of soft soil and/or foundations loaded with overturning moments and/or high horizontal forces. Statistical evaluation of UCS data using lognormal distribution is recommended, and a new classification system for DSM application is proposed. Field investigations and monitoring data from completed projects are also presented.INTRODUCTIONThe first applications of wet Deep Soil Mixing in foundation of road viaducts constructed across and along the newly built A2-highway in Poland took place in 2002. Following detailed analyses, it was concluded that 39 viaducts, originally designed to rest upon large diameter piles in order to reduce excessive settlement of individual supports, could also be founded directly on the ground improved with DSM columns, fulfilling all relevant requirements of serviceability and ultimate limit states (SLS and ULS, respectively). It was also noticed that shorter construction times and lower costs of ground improvement with DSM contributed to substantial economical savings as compared to classical piling. Since then, more than 250 road and railway viaducts have been successfully founded on DSM treated ground in Poland, and wet soil mixing is now seen as a reliable and widely accepted technology for this purpose. These applications, together with a parallel use of wet DSM for foundation of buildings, industrial halls and wind turbines, have drawn international attention to the state of practice of wet DSM in Poland for foundation of engineering objects. What follows is an attempt to summarise experience gained during planning and execution of DSM works for foundation of the majority of road and railway viaducts constructed in the last 13 years, with emphasis on selected design aspects and evaluation of collected data and observed performance.The design process of DSM treatment is iterative, as described e.g. in Annex B of EN 14679, and typically involves two main steps, i.e., the selection of the design strength of cemented soil, called soil-mix design, and the adoption of suitable column pattern, referred to as geotechnical design. Soil-mix design was initially based on purposely arranged simple laboratory tests, involving mixing of soil specimen with different cement types and dosages and subsequent strength testing. However, with a growing number of completed projects the accumulated field strength data of different stabilised soils have been more and more frequently used, reducing the need for preceding laboratory testing of soil-mix to special projects only. Information on cement factors utilised in Poland and the range of recommended compressive strengths for different stabilised soils, as well as on mixing tools and characteristics of the wet method applied, can be found in Topolnicki (2008). Consequently, soil-mix design is not further discussed herein. Selected aspects of the geotechnical design are the main focus."

Jan 1, 2015

By Timothy Nelson, Simon Burnworth

"The Berkeley Art Museum and Pacific Film Archive (BAMPFA), which currently resides in a 1970s-era post-modern concrete structure just south of the University of California, Berkeley campus, was in need of a new home after an engineering evaluation revealed that the building possessed seismic deficiencies. Pressed for space, the University looked within its portfolio of properties and identified the site of the former University Printing Press facility as the place to build BAMPFA’s new home.The site was perfect; located one block east of bustling downtown Berkeley and its rapid transit station, and directly across the street from the western entrance to the UC Berkeley campus. Thousands of pedestrians pass by the site on a daily basis, thus granting BAMPFA the opportunity to reshape the corner of Center and Oxford Streets with a building that would not only welcome visitors to campus, but also serve as a creative hub for both the City of Berkeley and the UC Berkeley institution itself 1.The original museum plans, drawn up in the mid-2000s, called for complete demolition of the existing abandoned facility and replacement with a visually stunning structure designed by renowned Japanese architect Toyo Ito. Even at this point, the shoring and means and methods requirements of the project were identified as a challenging component, incorporating a shored excavation bounded on three sides by busy city streets and a fourth side by an operating bank and occupied apartment building. Furthermore, a sequenced demolition would be required for the printing press facility’s three-story Administration Building (also known as the Admin Block), one-story printing press warehouse (also known as the Press Building), and an adjacent parking structure. Degenkolb Engineers was retained at that time as the shoring engineer to design the shoring to facilitate this work."

Jan 1, 2016

By Flor De Cock

The paper reflects part of the work from the European Regional Technical Committee on Piles (ERTC3) during its mandate between 1994 and 1999, and, in particular, describes the find­ings from an International Seminar held in 1997 in Brussels on European practice for design­ing axially loaded piles. The seminar included contributions from 17 European countries, each of which provided a synopsis of their respective national design approaches. This paper pays particular attention to the design methods based on laboratory and in-situ test data for both bored and displacement piles.

Jan 1, 2002

By Thoedtida Thipparat

The diaphragm walls and barrettes are very important to the constructions of multi-storeyed buildings, elevated expressways, subway railway stations, etc. Uncertainties particularly increase in accordance with the construction progress. Overcoming uncertainties influences the construction goals including achievement of time. This paper is aimed at proposing an uncertainty assessment and delay evaluation model to assess uncertainties and evaluate delay resulting from those uncertainties. Neurofuzzy systems (NFSs) for assessing uncertainties and evaluating delays are developed. Artificial neural networks (ANNs) have ability for learning from the past data and generalizing outputs for the next applications which are provided for fuzzy logic systems (FLSs). FLSs have ability for exploiting the tolerance of imprecision and uncertainty. FLSs provide the reasoning to the ANNs. Uncertainties affecting each operation were assessed and delays were evaluated by following steps of the proposed model. The uncertainty assessment and delay evaluation approach was applied to a diaphragm wall and barrette construction to demonstrate how to implement the proposed model. The results of the test case application were used for handling delay at all operations regarding the corresponding uncertainties.

Jan 1, 2006

By Scott A. Walker, Frank L. Rollo

"The San Francisco Museum of Modern Art (SFMOMA) in downtown metropolitan San Francisco, California, is supported on a mat foundation. Although the mat foundation of the original museum was designed to accommodate a future expansion, the plans for expansion that developed in 2010 required a larger footprint to accommodate the new space requirements of the museum. The new, larger expansion was designed by lead architect Snohetta. It will be a tall 12-story, steel-framed building occupying an area that was once the eastern part of the existing museum as well as two adjacent and newly acquired parcels.As designed, the expansion includes a 30-foot-deep excavation which is surrounded by adjacent buildings and improvements. Because of variable subsurface conditions at the site, geotechnical challenges included mitigating anticipated differential settlement between the existing and new foundations, preventing overstressing of the existing mat foundation, controlling groundwater to prevent settlement of surrounding improvements, and providing temporary support of adjacent structures during excavation for the new basement.To address several of the geotechnical challenges, soil-cement mixed (SMX) ground improvement was recommended by Treadwell & Rollo. However, during contract negotiations and construction, the specialty contractor proposed using jet grouting as an alternative technique for ground improvement. The jet grouting approach was accepted in principal, but when implemented was only marginally successful. Accordingly, the contractor eventually installed SMX panels using a Cutter Soil Mixing (CSM) machine. Because the CSM machine was a late arrival during construction, the contractor was not able to take advantage of the ground-improvement technique to install many of the shoring elements that we had originally recommended (such as the cut-off shoring wall). In the end, SMX panels were installed as ground-improvement beneath the new mat foundation to (1) reduce the potential for liquefaction in clean sand below the groundwater by providing increased rigidity to the soil, (2) reduce the potential for disturbing a weak underlying marsh deposit during construction, and (3) transfer vertical building loads to a layer of underlying dense sand.This paper also discusses the quality control and quality assurance programs that were implemented to check that the ground-improvement techniques used were thorough and complete and provided the required strength to transfer the new foundation loads to the underlying strata."

Jan 1, 2014

By Sanjeev Malhotra

The American Petroleum Institute (API) method of predicting pile capacities in sands is reviewed. Factors that influence pile capacity such as soil parameters, pile parameters, loading effects and installation effects are listed. In addition, the simultaneous occurrence of physical phenomena such as grain crushing, pile shaking, stress-redistribution and plugging add to the uncertainty in the prediction model. To better understand the method of prediction, each parameter and the associated uncertainty is revisited. It is evident that these factors are inter­related and sometimes compensating. This discussion also draws attention to the influence that pile installation procedures can have on pile capacities and highlights the need for field experience with various pile installation procedures for designers. In summary, the strength of the method lies in its simplicity and ease of application, but the possible savings generated by an improved method are too substantial to ignore.

Jan 1, 2000

By Ramin Motamed, Joseph A. W. Toth

Evaluation of the capacity of large-diameter drilled shafts using current load test methods present challenges when considering the magnitude of loads required to fully mobilize their capacities. Often, these full scale tests do not fully mobilize the capacity through side resistance. Therefore, the need for innovative solutions to extrapolate side resistance and interpret nominal capacity are of key interest. In this study, we evaluate three methodologies for extrapolating unit side resistance based on bi-directional load test data. Fellenius (2001) presented these methods for interpretation of pile capacity using static load tests. Our interpretations are based on the evaluation of 116 load tests. Unit side resistance was calculated and reviewed for each load test and categorized using three criteria of mobilization; (A) full, (B) partial and (C) linear. This study specifically focuses on load tests that showed fully mobilized unit side resistance behavior (Criteria A). The three methodologies were applied assuming Criteria (A) load tests were mobilized to 50% of their measured values. Subsequent comparisons of each extrapolation were then compared against the full measured values for each test and generally showed good agreement. INTRODUCTION It is widely accepted that conducting load tests such as standard top-down tests or bi-directional (i.e. O- cell) tests can help designers understand load-settlement behavior and the nominal resistance of drilled shaft foundations. These load testing methods provide the advantage of confirming design assumptions as well as improving the reliability of the foundation design. The potential cost savings from the application of these methods for mid to large size projects is self-evident. For example, in a recent project in Northern Nevada, an O-cell test on a 6.9 ft diameter, 114.8 ft length drilled shaft imposed an initial cost of $125k to the project, resulting in a 15% reduction on the total foundation cost; equivalent to $1.3 million in overall savings (Pease, 2014). However, the costs of implementing such methods on smaller projects can be prohibitively expensive (Hagerty et al, 2016). Despite the clear advantages of drilled shaft load testing, the current practice is not without limitations. Performing load tests on large-diameter drilled shafts with high capacities is a challenge considering the significant loads required to fully mobilize the capacity of such foundations. In some cases, the feasibility of these tests is impractical because the associated initial cost is not guaranteed to outweigh the final savings. As a result, large scale load tests are sometimes ruled out from the design phase of projects. Furthermore, in the majority of load tests the magnitude of loads applied are specifically selected to not approach failure, so the shafts can be used in the future foundation system (i.e. production shafts). This practice of field testing restricts our knowledge of the true capacity of the drilled shaft at failure; hence the nominal resistance remains unknown.

Jan 1, 2018

By Sangseom Jeong, Moonkyung Chung, Junyoung Ko

"Abstract The plugging effect of open-ended piles in sandy soil is analyzed by full-scale field test and plugging measurement. PLR (plug length ratio) measurement data from 144 field cases are analyzed with pile diameter. Based on the plugging measurements, PLR of open-ended piles which have above 1000mm diameter is predicted to be above 0.9. Through plugging measurements, a new empirical method is suggested for quantifying the plugging effect of open-ended piles. The proposed PLR equation is possible to predict the behavior of soil plug in the preliminary design stage. In addition, in order to investigate the behavior of the soil plug of open-ended pile, field load tests are performed on instrumented three piles driven into sand. It is obtained that the resistance components of open-ended pile are separated by double-walled pile system. It is found that inner shaft capacity is developed nearby pile tip. However, upper soil plug did not influence the inner shaft capacity. Also, it is found that all test piles are floating piles and unplugged condition because the sum of inner shaft capacity and outer shaft capacity is calculated about 58 to 76% of the ultimate bearing capacity.INTRODUCTIONIn Korea, a number of huge construction projects such as harbor terminals, offshore grand bridges, and lifeline systems are progress in urban and costal area. In these areas, steel pipe piles are frequently used to support high-rise buildings and heavy weight structures for ensuring structural safety rather than serviceability limit capacity. Also, steel pipe piles are frequently used in civil engineering structures because they have many advantages such as high-load bearing capacity, light weight and outstanding workability. The mega foundations of grand bridges and high-rise buildings are required in geotechnical engineering. Large diameter driven piles are frequently used in several projects.Many specifications such as API, FHWA and AASHTO have been reported as a design guideline of plugging effect, however , the current design method for plugging effect of steel pipe piles are mainly based on the our knowledge derived from observation of the model test or the small diameter pile load test. Therefore, these specifications have limitation to apply the large diameter steel pipe piles.Much work has been done to study the plugging effect by many researchers. Yamahara (1964) reported that soil plug has been modeled as a thin disk element as shown in Figure 1, since the increment of radial strain of the soil plug can be neglected due to high rigidity of the pile compared to that of the soil plug. Klos and Tejchman (1977) reported that the end bearing capacity of open-ended piles was almost equal to that of a closed-ended pile when penetration depth of pile was above 15times the pile diameters by model tests. Paikowsky and Whitman(1990) reported fundamental studies on mechanism of plugging effect in sand. Paik et al. (2003) reported that empirical relations for plug load capacity, annulus load capacity, and shaft load capacity of open-ended piles are proposed based on the model pile tests. As discussed above, much work has been done in the area of plugging effect. But little work has been done to study the plugging effect by full scale field tests."

Jan 1, 2014

By Larsson Lars-Erik, Rani Isa, Martin Jönsson, Håkan Bredenberg, Mats Larsson

"IntroductionSteel Core Piles are used extensively in Scandinavian countries, where hard rock is found within reasonable depths. A steel core is cast into a drilled steel tube casing and a rock hole is extended below the casing. This pile type is considered a very reliable type of pile, and for urban environment it has several advantages compared to other types of piles. One critical phase of the installation is the drilling of the casing. Usually a DTH (Down The Hole) hammer is used. Drilling in fine grained soils, e g silt, below the ground water level, may give rise to an excessive volume of soil material flushed up from the point of the casing, resulting in unacceptable settlements around the pile installation area.Using a new method for drilling of the casings, the ELEMEX-method has proven to significantly reduce the risk for such problems. In the paper a case record from a ground improvement project in central Stockholm is described. Ground settlements around the drilling area were carefully monitored over a longer period. Both the new drilling method and the conventional DTH casing drilling method where used, so that the corresponding ground settlements could be compared. Settlement records and comments are included in the paper.The paper also gives a description of the project. The installation of new piles and foundation constructions cover a whole city block in Stockholm downtown. The reason for the replacement of the old, damaged wooden piles were due to their destruction caused by a long time lowering of the ground water table. The paper gives a description of the new drilling method as well as an overview of usual urban foundation issues and their solution in Sweden, Finland and Norway.Drilled Foundation MethodDrilled Foundation, using drilling methods originally developed for drilling of large diameter rock holes, is today a standard method for the installation of piles, tiebacks, drilled pile walls and other foundation components, especially in urban built up areas where other techniques as drop hammers, augers, vibratory hammers and other equipment fail to meet the requirement, se ref(1). Drilled foundation is for example used for"

Jan 1, 2014

By Rick Deschamps

The Block 76 project includes the demolition and redevelopment of an entire city block for mixed use retail, office and residential properties directly adjacent to Historic Temple Square in Salt Lake City, Utah. Excavation was carried out 65 ft below street grade and by as much as 50 ft directly below adjacent buildings supported by shallow foundations. Movements of the earth retention system and adjacent buildings were monitored in real time using automated equipment which complemented traditional geotechnical instrumentation. In the areas immediately adjacent to the existing buildings 9 stories or greater, anchored diaphragm walls were employed. Areas of the site not supported by diaphragm walls employed a soil nail wall system. Jet grouting was used for water cutoff in lieu of dewatering along the north and east sides of project. In total, the earth retention scope included 45,000 sq. ft of diaphragm wall, 104,000 sq. ft of soil nail wall, and micropile underpinning of 3 buildings. This paper provides an overall description of the Block 76 project. A detailed account is provided of the technical and commercial lessons learned. The project provided a unique example of how an owner can receive best overall value by acceptance of some technical risk up front. Benefit was gained by allowing the contractor to reduce contingencies within the bid from unknowns on a fast-track project.

Jan 1, 2009

By R. L. Xu

In this paper, the author would like to point out with figures that the building industry is one of the key industrial sectors of the national economy in China. And in the coming 15 years, the output of building construction will not in the least decrease, but increase. The requirements for building standards, quality, functions as well as physical environment will also be higher along with the incessant development of the national economy and the gradual raising of people's living standard. China is a country with a vast territory and a great, variety of physical characteristics. The topographic and engineering geotechnical conditions are complex and varies considerably from place to place. Although, in recent years, encouraging progress has been made in building construction, there still exist many problems unsolved or even not explored at all, which we have to tackle in the future design and construction of foundations. Also reviewed in this paper are the achievements attained in the past thirty odd years and the challenge we will face in the foundation engineering field in China.

Jan 1, 2010

By David J. Baxter

Use of bored displacement piles has experienced significant growth in the UK piling market sector, largely due to their environmental advantages over other piling methods and through cost benefits. Bored displacement piles are a cast-in-situ construction which can be formed with minimal production of spoil and offer low noise and vibration compared to driven displacement piles. A large variety of bored displacement piles have been developed. This paper describes a standard system for their classification. The development of the different types is described along with the factors which have led to their increased use. Consideration is given to processes undergone by the soil during pile installation and design approaches for bored displacement piles are compared. Comparisons are made between the different classifications of bored displacement pile. Comments are also made on the installation of such piles. It is concluded that complex changes occur in the stress states of the surrounding soils. Such effect of the pile installation on the soil should be accounted for and there is a need, therefore, to further refine the design process for these piles.

Jan 1, 2006

By M. Pernot

A 12 m-deep excavation has to be perfomed in the Shanghai soft clay to install an underground electric substation. This article was originally intended to study the behaviour of the wall, the excavation bottom and the surrounding ground during the excavation. Since the works are behind schedule, and the data referring to the excavations are not, therefore, available, the article is limited to a presentation of the analysis methods that we envisaged for the study of the behaviour of the excavation.

Jan 1, 2010

By John N. Cunningham

Despite the wide use of micropiles for rehabilitating and retrofitting existing structures, little is known regarding the load-transfer distribution of grouted micropiles in various soil deposits. The rehabilitation of a concrete-frame warehouse in Portland, Oregon, required provisions for the seismic restraint of a new shear wall; the installation of two micropiles was specified to meet project requirements. The micropiles were uncased, 19-m (63-ft) long, 200-mm (8-in) nominal diameter, and reinforced full-length with a 64-mm (No. 20) diameter hardened steel threadbar. Due to space limitations, a sacrificial, instrumented micropile was installed near the two production piles to verify design assumptions. This paper describes the geologic setting of the project within the unsaturated Missoula Flood deposits, instrumentation, load-displacement behavior, load transfer, and Beta-coefficients for the sacrificial micropile.

Jan 1, 2011

By Clyde N. Baker

Foundations for the Sohio Corporate Headquarters in downtown Cleveland have column loads of 11,400 kips, which increase to 15,000 kips with wind loading. An extensive exploratory program was conducted and comprehensive studies made to select the economically dependable support for the 46-story structure. A test on bond or socket friction for the caissons has usable values.

Jan 1, 1984

By Mark R. Svinkin

Regulations are needed to keep construction vibrations in tolerable limits. The existing regulations were developed for low-rise residential structures, but they are incorrectly used for different super and underground structures. The existing regulations cannot prevent most of harmful vibration effects on sensitive devices, people and structures from construction and industrial vibration sources. It is important to determine the areas of application of the existing regulations and bring attention to the necessity of measurement of the structural responses for assessment of vibration effects on structures. For multi-story residential, commercial and industrial buildings, the frequency-independent safe limit of 51 mm/s (2 in./s) can be chosen for the peak particle velocity of structural, not ground, vibrations. Specifications for construction operations with dynamic sources have to consider specifics of each construction site. Preventive measures can be used to mitigate harmful vibration effects on various structures and settlements in sand and clay soils.

Jan 1, 2006