Search Documents

By Narong Thasnanipan

Performance of diameter 1.5 m toe-grouted bored pile founded at depth 44 m in sand-gravel formation of Chiang Mai City is presented in this paper. Toe grouting was applied by using tube-a-manchette method. Effectiveness of toe grouting was observed from the standard penetration tests conducted immediately below pile toe through grouting pipes at two stages, prior to grouting and three weeks after completion of grouting. Improvement of pile end resistance by toe-grouting is demonstrated with a series of back analyses carried out by load-transfer method employing hyperbolic transfer function. Construction experience of large diameter deep-seated bored piles in multi-layered subsoil and practical aspects of toe-grouting are also briefly discussed.

Jan 1, 2002

By Brett K. Mainer

In the summer and fall of 2007, Drill Tech Drilling and Shoring, Inc. designed and built three 24-foot inside diameter shafts in Northern California using soil mix panels for support. The soil mixing was performed using the Bauer Cutter Soil Mix (CSM) method, by which rectangular soil mix panels up to 71 feet deep were arranged in an overlapping manner to form a 24-foot inside diameter circle. The shafts were then excavated to depths up to 51 feet. One of the shafts was a test shaft and used only the soil mix panels for support. The other two shafts were located immediately adjacent to the Mokelumne River and were used as access pits for a microtunnel drive under the river. These two shafts had wide flange beams embedded in the panels and were supported with several levels of ring steel placed during excavation. This project was the first use of the Bauer CSM method in the United States. The CSM method has been used extensively in Europe and Asia, but never for this application and never with this high a loading criteria due to water head and microtunnel reaction forces. Soil conditions at the river crossing shafts consisted of sands, gravels, and cobbles over top of sandstone and conglomerate bedrock ranging in strength up to 5,000 psi. Groundwater was within several feet of the surface. The shafts were successfully completed between October 2007 and January 2008, and the microtunnel was successfully completed in February 2008. This paper provides discussion regarding selection of the shoring type, structural design, the soil mixing method, and the mix designs. Shaft construction, shaft performance, and the capabilities of the CSM equipment are presented.

Jan 1, 2008

By Peter Arz

In the port of Hamburg a 650 m long quay wall was completed in mid-1985. The watertight wall consists of loadbearing steel buttress piles PSP 1012 which are up to 28 m long and infill interlocking sheet piles PZ 612. The construction method used for this quay wall, which included the simultaneous implementation of ground improvement measures, is the subject of this lecture. Originally, as is common practice, driving of the sheet piles had been envisaged. The composition of the subsoil, which consists of fill, clay, sand and boulder clay, is typical of the Hamburg region. In the upper layers (down to a depth of approx. 15 m), the subsoil is interspersed with debris from ancient civilisations but also dating from the war and post-war period (bomb craters filled with debris and demolition material).

Jan 1, 1987

By Thomas M. Caruso

Construction of a new ship dock at a major Philadelphia area refinery required geotechnical design and field consultation. The new dock, which consists of a system of mooring dolphins and platforms, will be capable of docking the Stena V-MAX Oil Tanker (V-MAX). The 1100 ft long V-MAX is currently the largest tanker to travel the Delaware River and will induce significant lateral loads on the new ship dock. Lateral loads induced on the dock will be resisted by over 200 pipe piles installed on a batter. The piles used for support of the dock included 20 and 30 in. diameter reinforced, concrete filled pipe piles. Complete construction of each pile included driving of the pile to the design ultimate capacity, flushing the pipe pile casing clean of overburden materials followed by drilling rock sockets into the underlying Wissahickon Formation. Variations in depth to bedrock, rock quality and degree of weathering and presence of very hard quartzite lenses created a complex geologic environment that presented challenges for the pile/rock socket design and installation. The design of the pile system, installation methods, QA/QC and testing (Pile Dynamic Analysis), as well as the challenges that were encountered through the duration of the project are presented and discussed.

Jan 1, 2008

By Frank Borda

Two recent projects were completed in Ontario, Canada for major hospital additions that involved excavation support of heritage masonry structures. Conventional continuous caisson wall schemes were replaced, with significant cost savings, by tied back shotcrete systems. Using a combination of conventional design and FLAC analysis, excavation support was designed to permit excavation in competent to weak soils that limited horizontal movements of the existing structures to between 3 and 8 mm. The use of vertical wall elements (micropiles) integral to the shotcrete wall to support both the vertical wall loads and the face of the excavation was deemed to significantly reduce lateral and vertical wall movements. FLAC analysis was used successfully to predict wall movements and optimize design. The shotcrete method proved to be flexible and adaptable to design changes during the project. This permitted convenient accommodation of changes to the building geometry after excavation support had commenced. In addition the method accommodated staged demolition and excavation support of portions of the existing structure at low cost, conveniently and without delays.

Jan 1, 2004

By Nathan A. Ingraffea

The use of steel sheet pile walls and drilled shaft foundation elements to enable up-down construction methods has been used successfully on recent high-rise structures with multi-story below grade parking. The John Ross Tower and The 3720 Tower in Portland, Oregon each make use of this system and are discussed in-depth. Up-Down construction involves the simultaneous construction of the building levels above and below grade instead of the standard construction technique of excavating and shoring the below grade construction before being able to build upward from the base of the excavation. Advantages of the up-down system include a shortened overall construction schedule, permanent basement walls that double as the temporary shoring walls, elimination of the typical continuous wall footing or grade beam at the building perimeter, increased use of recycled material (steel) while maintaining an overall decrease in total materials, elimination of wall forming costs, decreases in forming costs for slabs, decreases in waterproofing costs for walls and elimination of pile caps and/or footings for the building columns. Lessons learned during the construction of both buildings include the need for more extensive geotechnical boring information, descriptive sheet pile and drilled shaft specifications, a clear understanding from the design team on finished appearance of sheet pile and shafts, and careful consideration of the connection between both slabs and the sheet pile wall and slabs and drilled shafts.

Jan 1, 2008

By Silas C. Nichols

FHWA Interest is due to: ? An increase in successful projects in the U.S. private sector and in other countries ? Cost effective and more efficient in many circumstances ? Agency Priorities - FHWA "Vital Few" AASHTO TIG

Jan 1, 2005

By Farhad Elmi

In this paper, a new procedure is used to find the bearing capacity of single piles and cone penetration resistance in soils. Although the procedure is mainly applicable to clay and sand using any plasticity model, this paper deals only with steady penetration in Sand. Cylindrical cavity expansion around the probe in a calibration chamber is modeled by finite element method using the HUJEUX elasto-plastic multi-mechanism model. The penetration resistance (qc) is related to cylindrical cavity expansion pressure limit (pL) using the method of Salgado et al. (1997). This procedure is tested using the results found in 3S/IMG calibration chamber. In this article the word "penetrometer" refers to both pile and cone.

Jan 1, 2002

By Shenbaga R. Kaniraj

The pile loading tests are generally conducted to assess the safe load on piles in compression. In the Indian practice, the safe load is determined using the pile loading test data and the two criteria specified in the Indian Standard Code, IS.2911 (Part 4) -1985. For this, the test pile should have undergone a minimum displacement equal to 10% of the pile diameter. Often, the piles are not subjected loads that are sufficient to cause a displacement of this magnitude. If the settlement is at least 12 mm, then the safe load is determined based only on the first criterion. But, if the settlement is less than 12 mm, the safe load cannot be determined using the IS Code criteria. The paper presents two procedures called hyperbolic and generalized hyperbolic methods to estimate the safe load using the IS Code criteria even when the loading test data is insufficient. The data from two initial tests have been analyzed. The predicted safe loads have been compared with the actual safe loads.

Jan 1, 1996

By Gerald Verbeek

There are certain concepts that seem to invite responses from some, including some in the foundation industry and even some within DFI, that are at best surprising. Business owners and their employees share the desire that their company does well and continues to operate. Maybe company growth is not always realistic but maintaining the current level of activity is in the least what they hope for. In other words, they hope that their company is sustainable, and they are fully behind that notion. But when the concept of sustainability is raised, there is, at least with some, suddenly doubt that that is a good thing. And yet, that concept only aims to achieve at a grander scale what the owners and employees desire for their company. There are many definitions of the term sustainability, but probably the most commonly used description is that framed by the United Nations in 1987. It states that sustainability is the concept of meeting the needs of the present without compromising the ability of future generations to meet their own needs. Arguably that definition is too abstract and does not provide the type of specific goals and targets we are used to. To help with that, to some extent, in 2015 the United Nations formulated 17 Sustainable Development Goals (SDGs), to provide "a shared blueprint for peace and prosperity for people and the planet, now and into the future." And undoubtedly those SDGs are fodder for those that question the concept of sustainability in the foundation industry. How can our industry, they wonder, ensure that there is no poverty or hunger (SDG 1 and 2), and the climate action goal (SDG 13) immediately leads to the hot button topic of global warming. And maybe this is where advocates lose (some of) the sceptics of the sustainability concept, but hopefully they will continue to read this article that lays out why sustainability simply makes sense, also for the foundation industry and especially for DFI.

Nov 1, 2022

By Aditi Sharma, Sumanta Haldar

Scouring of soil is the major concern forthe various hydraulic structures built in the flowing rivers since scouring impacts the bearing capacity of foundations. Hence, consideration of scouring in the design of foundations for hydraulic structures is crucial. Pile groups in bridges are subjected to combined vertical and horizontal loading due to self-weight, live loads, vehicular impacts, wind load, earth pressure, and current. Hence, an assessment of the combined bearing capacity of pile groups subjected to scour is essential for the safety of the structure. This paper aims to analyze the bearing capacity of pile group supporting the bridge under combined loading i.e., Vertical (V) and Horizontal (H) loading subjected to local scour. Three-dimensional finite element model (3D-FEM) of a 3 x 3 pile group embedded in homogeneous sandy soil is established in Abaqus (2018). Mohr-Coulomb plasticity model is used for the soil domain. The pile group is modelled as linear elastic. Finally, V-H yield envelopes are obtained with and without scour. The potential impact of different parameters, such as angle of attack, flow velocity, depth of flow, and different pile length-to-diameter ratios (L/D) and spacing-to-diameter ratios (S/D) of pile group on V-H yield envelopes is studied.

Sep 1, 2022

By H. R. Masoumi

This paper presents a numerical model for the prediction of free field vibrations due to vibratory and impact driving. As the focus is on the response in the far field, where deformations are relatively small, a linear elastic constitutive behavior is assumed for the soil. The free field vibrations are calculated by means of a coupled FE-BE model using a subdomain formulation, proposed by Aubry and Clouteau (1992). The model is validated by means of the results of Kaynia and Kausel (1991) for the impedance of a single pile. First, the case of vibratory pile driving is considered, where the contributions of different types of waves are investigated for several penetration depths. The results show that in the near field, the response of the soil is dominated by a vertically polarized shear wave, whereas in the far field, Rayleigh waves dominate the ground vibration and body waves have been importantly attenuated. Second, the case of impact pile driving is considered. A linear wave equation model is used to estimate the impact force during the driving process. Furthermore, it is investigated how the soil stratification influences the ground vibration considering the case of a soft layer on a stiffer half space. The results show that when the penetration depth is smaller than the layer thickness, the layered medium has a small influence. However, when the penetration depth is larger than the layer thickness, these effects become more significant. Finally, the computed ground vibrations are compared with experimental data reported in the literature.

Jan 1, 2006

By Hitoshi Ogura, Koichi Kobayashi, Sadao Yabuuchi

"In Japan, most pile foundations using pre-cast concrete piles are installed by the bored pre-cast piling method, wherein pre-cast piles are installed in holes that have been excavated beforehand and filled with cement milk (term used for cement water slurry in Japan). The bored pre-cast piling method with enlarged base, in which the portion near the toe is enlarged during boring operation, is widely used because of the cost benefits and the increased vertical bearing capacity that this method offers.The EX MEGATOP method, further developed as an improved bored pre-cast piling method with enlarged base, is reported here. The features of this method are: (1) High vertical bearing capacity; (2) High degree of freedom in design; (3) Excellent workability; and (4) Friendly to the environment. In particular, high vertical bearing capacity can be obtained using nodular piles and by enlarging the area at the pile toe and shaft. This method can gave a vertical bearing capacity coefficient at the toe of a=430, more than twice the corresponding value of a = 200 of a conventional bored pre-cast pile. Moreover, the shaft resistance can be several times larger than that of a conventional bored pre-cast pile. This report gives an overview of the EX MEGATOP method, evaluation of vertical bearing capacity, and examples of application of the method.1.lntroductionMost pile foundations in Japan are installed by the bored pre-cast piling method, that is, in holes that have been excavated beforehand and filled with cement water slurry, referred to as 'cement milk'. The ""bored pre-cast piling method with enlarged base"" is frequently used. In this method an enlarged excavation is used near the pile toe to increase the vertical bearing capacity.The EX MEGATOP method is a variation of the bored pre-cast piling method. Its features include the use of nodular piles and a long, enlarged excavation. The vertical bearing capacity of the EX MEGATOP method is described in this report."

Jan 1, 2005

By P. D. Arumairaj, B. Vani

"Micropiles are small diameter cast insitu reinforced grouted piles and it has been effectively used in many applications of ground improvement. It increases the load carrying capacity of soil and reduces the settlement. It is also used in strengthening existing foundations. In this study, the effect of Solid and Hollow micropiles on the load carrying capacity of footing resting on sand is studied. The effects of solid Micropiles are investigated by conducting experimental model studies. The parameters involved in this study include the position of pile, pile length and pile spacing. Load test was carried out on a model footing resting on sand with solid and hollow micropiles. Load test trail is repeated for footing on Micropiles with varying lengths of 10, 20, and 30 times the diameter and spacing equal to 5, 4, 3, 2 times the diameter. The load-settlement behavior of each case is compared. Optimum length and optimum spacing of both the solid micropile and hollow micropile are determined. It is also observed that the effect of micropiles in the peripheral of footing resists lateral displacement of soil underneath the footing. The micropile beyond significant depth becomes redundant.INTRODUCTIONA micropile is a small diameter (less than 300 mm) drilled and grouted pile that is typically reinforced - FHWA-NHI 2005 (Federal Highway Administration-National Highway Institution). It is constructed by drilling a borehole, placing a steel reinforcing element into the borehole and grouting it. Hollow micropiles are typically reinforced by solid central bar that occupies about onethird of the hole volume. The grout is placed by gravity, under pressure methods or by a combination of both (post grouting). Thus, micropiles can be considered as small drilled-shafts that are specially drilled and grouted.Historically, micropiles have been introduced in Italy as a foundation system mainly for retrofitting and underpinning of structures that had sustained damage during World War II and access for conventional piling equipment was not possible (Bruce, 1988). The second generation of micropiles is a pressure grouted piles with a central mono all thread bar (with diameter up to 89 mm). They are installed by using either an open or cased hole drilling method.A new generation of micropiles, termed Grout injection bore micropiles (IBOR), was developed in the 1980s. The IBOR, currently named hollow bar micropiles, utilizes a continuous all-threaded hollow steel bar as the drilling and grouting conduit, which allows drilling and grouting simultaneously without the need of a casing during drilling. A sacrificial (lost) bit with openings that allow for pressure grouting of the hole is threaded onto the end of the hollow bar and is left in place following drilling. A drilling fluid (air, water, or grout) is introduced through the hollow bar and allows the spoils to flush from the borehole opening. Upon reaching the required depth, neat cement grout is then injected under high pressure into the drilled hole to fill the annulus between the bar and the soil from the bottom to the top. Due to the grouting method employed, the shape of the hollow bar micropile is expected to have a bulb shape with an enlarged base."

Jan 1, 2015

By Dennis Wrixon

It was a little bit exceeded. The decision was the uniform settlement is measured at each one corner and the highest one corner is the important one. And in addition there is a differential settlement of 2.1 mm allowed. So we reached about 7.8 or 7.9 mm with the highest corner and in addition 2.1 so it was a little too much. But behind there is a very difficult calculation of the authorities where all of the displacements are combined together and there are of course some more factors of safety in these settlements.

Feb 10, 2003

By A. A. Gupte

Auger piling system which was developed in the United States in the 1940's is gaining acceptance in many parts of the world. Although primarily used to support foundations, the system is very useful for many other applications such as soil anchors, temporary and permanent earth retention systems, restricted headroom piling and underpinning of existing foundations. In this paper, review of current construction design techniques for the Auger piling system for earth retention and underpinning of structures is presented.

Jan 1, 1989

By Craig M. Shillaber

On any given day, a simple check of the news will turn up stories related to sustainability, resiliency, climate, or human or natural disaster. In recent years, the winter power grid failure in Texas, the Surfside Condo collapse, unsafe drinking water in Flint, Michi- gan, the Oroville Dam spillway failure, wildfires and flooding (to name a few) have appeared in the U.S. news cycle. As a result, young people are aware of the problems and challenges facing the nation and the world and want to be part of creating sustainable solutions for society. Many choose to major in civil engineering because of a desire to make a difference, address climate change, and develop sustainable and resilient infrastructure for the future. Sustainability is at the core of modern civil engineering practice. In its Policy Statement 418, the American Society of Civil Engineers (ASCE) explains sustainability is a set of conditions where human society can indefinitely keep and enhance quality of life without deteriorating economic, environmental and social resources. Sustainability is an integral part of the technical outcomes identified in the ASCE Body of Knowledge and features prominently in the ethical responsi- bilities of engineers based on the latest version of the ASCE Code of Ethics. Thus, to prepare graduates for successful and ethical engineering practice, civil engineering programs must provide instruction in how to account for social, environmental and economic con- straints in design. Since the deep foundations industry is integral to the broader civil engineering and construc- tion fields and is responsible for supporting critical infrastructure on which human society depends, sustainability should be a key con- sideration in foundations projects. Given the importance of sustainability within civil, geotechnical and foundation engineering, it is worthwhile for the deep foundations industry to consider where and how engineers are trained in sustainability topics through higher education at the undergraduate and graduate level, and what is driving sustainability content in civil and geotechnical engineering curricula.

Nov 1, 2022

Pier, well cap and steining junction is a complicated 3-d re-ion. The prevalent design procedure for the pier, well cap and steining in isolated manner is not rational. In absence of an integrated approach for design of the junction structure, the well cap is designed uneconomical and at the same time pier and steining are left relatively unsafe. Strut-and-Tie Model based design is a simple solution to this problem. An example illustrating design of the junction structure using STM is presented. On comparison of the outcomes of the STM based design with the prevalent design, the following anomalies are found: i) For smooth flow of forces, length of pier at its base should preferably be made equal to the outer well diameter, ii) STM based design for the pier is more rational, economical and safe. iii) Due to presence of hoop stress, as indicated by the STM, the steining concrete in a depth of p times outer diameter of the well from the well cap level should be limited to M15 grade, iv) STM based design for the steining is more rational, economical and safe.

Jan 1, 1996

By W. G. K. Fleming

The codification of foundation design and construction is a subject of extensive discussion in Europe and all current code proposals are based on limit state partial factoring. For simplicity, it is claimed, simplified forms of Partial Factor use are presently being advocated but, if this is the direction which codes are to follow, then it is preferable in this age of computer technology that a true system should be adopted rather than a simplification. A philosophically satisfactory method can readily be found which can fulfilcurrent requirements and it is better that such a method should be adopted from the beginning rather than later to find it necessary to make important alterations and amendments.

Jan 1, 1996

By Naim Noori Samie

Lateral force rsistance of piles is analytically investigated by dividing the pile length to 3 segments. The first segment (Zone I) models the load eccentricity with respect to the soil and the pile-deck connection, using a third degree differential equation representing the shear variation along the pile. The soil is assumed to be uniform, homogeneous with an elastic-perfectly plastic behavior. The Top soil layer (Zone II) is assumed to be stressed beyond the elastic limit. A simple 4th degree differential equation represents this zone. The soil resistance is assumed to vary linearly with depth (or surcharge). The pile deformation and soil behavior determines the plastic zone length. In zone III the soil is assumed to behave elastically, hence its resistance is proportional to its deformation. A linear 4th degree differential equation is employed in this zone. The compatibility conditions are satisfied on each boundary. Maximum allowable moment and shear are investigated throughout the pile as the basic limiting criteria on lateral force capacity. In this paper the soil coefficients are taken from a proposal by ref(3), and the results are compared with the soil response as determined by the P-Y method as recommended by ref(2).

Jan 1, 1996