Search Documents

By Cau T. Bui

Thanks to Doi-moi (renovation) policy, many great bridges were constructed in Vietnam to meet demands of her booming economy in the recent decade and deep foundation structures were the only alternatives for the foundations of these great bridges. The deep foundation structures were constructed by modern technologies and almost of all these deep foundation structures were designed by foreign companies and carried out by Vietnamese workers and engineers under supervision of foreign experts. Beside successes, there were several failure cases in which the collapse of temporary scaffolding system of Can-tho Cable ? Stayed Bridge due to settlement of its pile foundation killing 54 workers and seriously injuring 80 other workers was the most serious. This paper introduces construction techniques of the deep foundation structures applied to building of great bridges in Vietnam recently. It will especially focus on two failure cases: 1) collapse of temporary scaffolding system of Can-tho Cable ? Stayed Bridge due to settlement of its pile foundation and 2) failure of drilled shaft foundation of Thanh-tri bridge due to poor construction technique and management. These two failure cases were greatly concerned by both bridge specialists and the public. Reasons of and lessons from these two failure cases will be carefully discussed. From the two failure cases, this paper will draw some lessons that should be important issues to be seriously paid attention when designing and constructing deep foundations in Vietnam.

Jan 1, 2008

By Charles M. Wilk

"Mass stabilization (MS) is a ground improvement technique that can prepare areas of low bearing strength soil for subsequent infrastructure development. The technique involves mixing binding agents such as portland cement, fly ash, slag, or lime into the subject soil while the soil remains in-place (insitu). The binders “cement” the soil grains together to form a cement modified soil or a soil cement. The MS-treated area now has improved bearing capacity to support infrastructure or to prevent movement of the material such as landslides.The same insitu soil mixing technique can be used to address contaminated areas. Binders or reagents are mixed into soil. The treatment protects human health and the environment by immobilizing hazardous constituents within the treated material. When used for the purpose of environmental remediation the technology is called Insitu Solidification/Stabilization (ISS).Both Mass Stabilization and ISS treatments require laboratory studies to develop a mix design of soil and binder(s) that produce the desired physical and/or chemical properties. The mix design is then transferred into the field. Successful MS and ISS treatments rely on reproduction at full-scale of the mix design and the thorough mixing attained at laboratory scale. Fifty to 70% of the cost of a MS or ISS project is in the cost of the binding agent that is to be mixed into the subject soil. Under-dosing, overdosing, non-thorough mixing, and mixing in the wrong areas all create cost over-runs.This paper will discuss recent innovations in mass stabilization systems that improve the cost effectiveness of the treatment technology. Specialized equipment can impart greater mixing shear thus improving the thoroughness of mixing. Dry powder pressure feeders can conserve the “drying capacity” of binder resulting in higher strengths at lower binder dosages. Global Positioning System (GPS)-based systems can guide the mixing operator for complete mixing coverage. An integrated tracking and feeding system can record that proper dosing and mixing was accomplished and generate construction QA/QC reports for the client.INTRODUCTIONNew or expanding infrastructure projects may encounter areas of low bearing capacity soil or areas where marginal materials such as waste, dredged material, or sediment have been placed. Mass stabilization is a geotechnical method that can be used to improve the bearing capacity or stiffness of soil. Mass stabilization involves mixing binding agents into soil subject to treatment while the soil remains in-place or insitu.Mass stabilization technique can also address contaminated soil therefore, the same technique can be used to attain both civil and environmental engineering goals. In this environmental application the technology is known as insitu solidification/stabilization (ISS). ISS protects human health and the environment by immobilizing hazardous constituents within the treated material."

Jan 1, 2015

By Arturo Ressi di Cervia

"The Construction of the Thrust Pits for Jacking of the I-90 Tunnel for the Central Artery/Tunnel Project (Part of Contract No. C09A4) in Boston MA was nominated for DFI’s 2002 Outstanding Project Award. In the judging, the project and the specialty subcontractor, Treviicos Corporation, was chosen for a Special Recognition Award. INTRODUCTIONBoston’s Big Dig, as the construction of the underground artery became known, is undoubtedly the largest urban construction project of this century.The Central Artery/Tunnel Project, or CA/T, to call it by its proper name, runs approximately eight miles through the heart of Boston, five miles of which are built underground while maintaining traffic on the elevated existing structure, while at its southern end I-90 is extended to Logan airport under active rail lines, Fort Point Channel and Boston Inner Harbor.Since the alignment of the road closely parallels the shoreline as it existed in colonial times, the cut and cover construction had to contend with substantial portions of filled ground, not to mention existing subway lines, live utilities, building foundations and, last but not least, the irritable Boston drivers and litigious adjacent property and business owners.Consequently, while it is impossible to single out the most difficult or challenging contract, the jacking of the tunnels of I-90 under the live rails of Amtrak certainly will rank high on the list.Never before, anywhere in the world, was an attempt made to jack tunnels of this size: the South Bay Interchange consists of three 78 feet (24 m) wide by 38 feet (11.6 m) high tunnels, the shortest of which is 167 feet (51 m) long. TECHNOLOGYIn order to achieve this engineering feat it was necessary to consolidate the soil under the track to prevent it from moving or settling during the jacking process. After a detailed analysis of the geological profile to be traversed it was decided that freezing was the most suitable method, since it could be applied to the full range of soils present on the proposed alignment."

Jan 3, 2003

By Shamsher Prakash

Estimation of vertical load carrying capacity of a single vertical pile under earthquake loading is an important task of a design engineer. Lateral vibration of vertical pile is highly influenced by the magnitude of vertical load. Several load reversal, during earthquake loading introduce gap between pile soil interface which reduces its load carrying capacity and increases lateral motion. This paper presents a simple time domain numerical scheme to estimate the lateral pile response, considering the loss of contact of pile at pile soil interface, during impact and earthquake loading. The motion of the pile is limited in the vertical plane. Time domain has been discretised into small intervals. The non linearity of soil properties has been taken into account by discretised Winklers model with Wolfes frequency independent mass spring dash pot coefficient for geometric damping. Suitable software has been developed which keeps track of the load reversal point of each elements.

Jan 1, 1996

By Kyle A. Kershaw

The City of Grand Forks, North Dakota obtains drinking water from both the Red River and Red Lake River through a system of raw water intakes, shallow pipelines, and pump stations. However, during flood events, the City often loses access to the system, as evidenced during the record flood event in 1997. As a result, the City decided to construct a new gravity raw water intake system, including a pump station at the base of a 65-foot-deep, 60-foot-diameter caisson, behind a new levee system. Because of high design flood elevations and connectivity of river head to underlying soils, uplift resistance was required for the caisson. A total of 37, 2-foot-diameter, augered cast-in-place (ACIP) piles were chosen to provide uplift resistance. Because of the difficulties associated with installation of piles within the confined space of the constructed caisson and basal stability concerns, installation was completed from the existing ground surface to a depth of 120 feet. Several design and construction issues arose, including squeezing ground during pile installation, placement of long reinforcing bars, and installation of a dual material pile. A dual material pile was required to ensure that the ACIP pile below the base of the caisson was structurally sound and the pile above the base of the caisson could be easily excavated during sinking of the caisson. This paper discusses the solutions to each of these issues, as well as construction sequencing, load testing and integrity testing of the ACIP piles, and the successful completion of the project.

Jan 1, 2003

By Alberto Carmona Rosell, Sri Ram Ramankutty

"The installation of Bored Piles and Diaphragm Wall under slurry using tremie raises quality concerns on the integrity of concrete. It is vital to understand the effects on concrete integrity during concrete pouring process. This paper intends to unveil to what extent the compressive strength of the concrete pour is affected in contact with drilling fluid still. Another important angle of analysis proves whether the inclusion of solids particles of un-hydrated fluid could have impact on the concrete compressive strength. The testing comparing the response of concrete compressive strength when drilling fluid is included into the concrete mix altering the water/cement ratio by 5%, 20% and 30%. Comparative results are analysed between two different hydrated slurries namely sodium activated Bentonite and 3rd generation synthetic polymer.1. INTRODUCTIONSoil stabilization is the base for a successful deep foundation execution. The G3 System Slurry developed by Ground Engineering Operations (GEO), with its third generation polymer, namely PolyMud®, is an innovative and unique alternative to the mineral based slurries for soil stabilization, enhancing the quality and integrity of the underground foundation structures. It optimises the production rate of work progress and cost as well. At the same time, PolyMud® slurry is proven to be environmentally friendly.Guaranteeing the maximum quality of the foundation elements according to the initial design is one of the most important objectives and a concern for the foundations contractors. In order to fulfil the project expectations in this aspect, any incident that could compromise the designed concrete integrity and capacity must be avoided.GEO, has carry out its own research regarding effects on the concrete compression results if drilling fluid intermixes with fresh concrete while pouring. To shed light in this regard, GEO, in collaboration with CML (Concrete Materials Laboratory) Sdn. Bhd., carried out empiric tests that analyse this particular event from different perspectives, bringing up the corresponding results that will be studied and commented in this article."

Jan 1, 2015

By Sebastian Fischer, Rolf Katzenbach, Steffen Leppla

"The risk management in the case of liquefaction is one of the most serious and also difficult issues in geotechnical engineering because failure caused by liquefaction is always a sudden failure without ahead indication. For that reason ground improvement technologies for the prevention of liquefaction are necessary. The paper explains the responsible and effective risk management. Methods for the risk management and stabilizing the soil sustainably are described in detail.1. INTRODUCTIONDue to population growing more and more settlement area is needed, which is often including improper regions (e.g. mountain and coast regions) with raised risk of various kinds of disasters. But also in densely populated areas the risk of disasters like landslides can occur. One reason for the raising of risk in densely populated regions can be the opencast mining for raw material production. An essential element of the opencast mining is the loose deposition of the removed overburden, the so-called “overburden dump”. When an opencast mining is running out of the raw material, an opencast hollow remains in landscape. The slope areas of these hollows mostly consist of loose bedded material of the overburden dump. Due to the end of groundwater conservation these loose bedded slope areas are flooded. In consequence the slopes are in extreme danger of becoming liquefied. The result of a liquefaction in these slopes will unavoidably be a slope slide. Such a slope slide can extend up to several hundred meters into the landscape and can move several million cubic meters of material. An upsetting example for such a landslide is the slope failure in the German city of Nachterstedt on July, 18th 2009, which made necessitate remedial measures and also prevention works for the further utilisation of the region. The phenomena of liquefaction is not limited of slopes in series of opencast mining. Especially in regions with a highly appearance of earthquakes the phenomena of liquefaction is well known.2. RISK MANAGEMENTAn essential part for the stability assessment of slope systems is the investigation of sensitivity against liquefaction. In the case of given sensitivity against liquefaction there is no calculation method according to soil mechanics to determine the factor of safety against slope failure. Just for the case that sensitivity against liquefaction is not met, a comparison of the load (effect) E and the resistance R which is the traditional verification of stability against slope failure, can be calculated (Figure 1)."

Jan 1, 2015

By Hyung-Min Kwon

There are a number of methods available that can be used to estimate the bearing capacity of piles that are subject to lateral load, such as the theory of subgrade reaction or the elastic continuum approach. The objective of these approaches is to determine the lateral load corresponding to the allowable lateral displacement of the pile. It is important to select the appropriate soil stiffness when analyzing soil behavior within the allowable displacement of piles because the stiffness of soil is dependent on the displacement of piles. Even though pressuremeter tests can measure the stress-strain behavior within a wide strain range, pressuremeter test results have been utilized to assess only the fragmentary soil modulus based on either semi-empirical correlations or analytical approaches. This study is concerned with a methodology that can estimate the horizontal deformational property, while taking into consideration the nonlinear deformational characteristics of sandy soils. Pressuremeter tests were conducted for 15 cases using a calibration chamber. Reloading curves were employed in the estimation of horizontal deformational property in order to minimize the effect of soil disturbance caused by the installation of the probe. The shear modulus degradation characteristics were estimated from the curve fitting for the reloading curve and from extrapolation using the exponential function. In addition, the difference was taken into account between the stress state around the probe in reloading and that of the in-situ state. A consistent relationship was observed between the maximum shear modulus taken from the suggested method and the bender element tests performed in the calibration chamber, simultaneously with the pressuremeter tests. In addition, the results showed significant concurrence with the well-known empirical correlation.

Jan 1, 2008

By Sherrill Gardner

Vibratory drivers have been used since the 1930s to drive and extract piles. Vibratory pile drivers have the capability of significantly decreasing pile installation time, especially in granular type soils. However, they have not been widely accepted because of the uncertainty in estimating the bearing capacity of the driven pile. When driving bearing piles, the industry standard method for obtaining load carrying capacity of a pile installed with a vibratory driver is to redrive with an impact hammer. The advantage of improved productivity is lost with the redrive procedure. Currently, there is no other method to predict the capacity of these bearing piles installed with a vibratory driver. The Naval Civil Engineering Laboratory (NCEL) is making progress towards being able to estimate the bearing capacity of these piles. This paper describes field testing and corresponding analytical modeling of the vibratory driver-pile-soil system. The following sections describe the development of the numerical model and techniques for collecting field data. A discussion of the prediction of the pile driving process based on field test data is followed by suggestions as to the additional work that should be done to further verify the model to a point where it can be used with confidence.

Jan 1, 1987

By N. V. Nayak

Konkan Railway Project is one of the most ambitious railway construction projects in India, involving construction of a 760.km long, Broad Gauge (1676 mm), single track railway line, connecting Roha in Maharashtra State with Mangalore in Kamataka State. The railway line travels along the Western Coast of Indian subcontinent, through states of Maharashtra (382 km), Goa (105 km) and Karnataka (273 km) (Fig.1). The project alignment traverses through one of the most formidable terrains ever encountered, in the history of railway construction in India. In the State of Goa only, railway alignment is crossing 6 major rivers Terekhol, Chapora, Mandovi, Zuari, Sal and Talpona. Zuari Railway Bridge (1305.6 m), Mandovi Railway Bridges (I and II) (1182.7 m) rank as 2nd and 3rd long bridges, (first longest bridge being Sharavati Bridge (2.2 km} at Honavar) which have been constructed on Konkan Railway. All these three bridges have been constructed by M/s.Asia Foundations and Constructions Ltd. (AFCONS). This paper presents, case history of construction of pile/caisson foundations for Zuari and Mandovi Bridges.

Jan 1, 1996

By Richard Schmidt, Lijun Deng, Mohamed Abdelaziz, Weidong Li

Helical piles are widely used as a foundation supporting a variety of different structures. Understanding the axial behaviour of helical piles is required to confirm the engineering design. Helical pile research is often conducted in the field, but this method can be prohibitively expensive in some cases. Geotechnical centrifuge modeling offers an alternative method for the helical pile research and practice. A series of axial load tests of helical piles installed into cohesive soils were conducted on the geotechnical centrifuge at the University of Alberta. The objective was to investigate the effects of inter-helix spacing and soil strength on the axial behaviour of helical piles. Four types of aluminum model helical piles including one single-helix pile and three double-helix piles with various inter-helix spacing ratios were tested. Both compressive and tensile loading tests were conducted. All model piles were instrumented with multiple strain gauge stations. The clay had an undrained shear strength of approximately 50 kPa and 120 kPa. The test results indicate that there is a transitional failure mode between the two widely recognized failure modes, i.e., individual plate bearing and cylindrical shearing. The shaft adhesion was significantly reduced by the helix. Axial capacities were comparable to the field test results.

By Mario Carnevale, Myles Danforth, Michael Oakland

The cost and overall effectiveness of foundation design depends on a robust characterization of the subsurface geologic setting. It is common practice to formulate deep foundation design from subsurface geologic characterization based on boring programs. The confidence level of geologic characterization is directly related to that of geologic interpretations, which are based on the spatial sampling pattern of boreholes relative to the complexity of the geologic setting. This paper presents a case history illustrating issues that arise during pile construction from over-simplified geologic characterization, the challenging steps taken to improve the subsurface geologic model, and the effect of additional characterization efforts on the pile foundation program. The seismic characterization methods used include multi-channel analysis of surface waves (MASW) and seismic refraction.

By John Y. L Chen

This paper presents full-scale instrumented pile static compressive and tensile load tests to be conducted in the area of Pearl Harbor, Hawaii. Thousands of piles have been installed to support the existing piers and wharves in the Pearl Harbor area. Due to the absence of bedrock within practical depths, most of the piles use combined friction and end bearing. A new 925 feet (282 meters) long and 50 feet (12 meters) wide reinforced concrete wharf supported on pile foundation is planned. This paper will present results of soil investigation, laboratory testing, dynamic load tests during indictor pile driving and static pile load tests. The subsurface conditions consist of soft harbor sediment, young alluvium deposit, volcanic tuff rock formation and stiff old alluvium deposit. The load test piles consist of 20-inch (508 mm) square and 24-inch (610 mm) octagonal pre-stressed, pre-cast concrete pile and instrumented with embedded strain gauges. The length of the piles ranges from about 50 to 125 feet (15 to 38 meters). The test pile program consists of probing, driving indictor piles, dynamic load tests during indictor pile driving and static load tests. The standard loading procedure method was used during static pile load tests.

Jan 1, 2002

By M. Y. Xia

In this paper, based on the Theological tests of the interface between clay and concrete, an interface Theological model is proposed and is used in the finite element analysis which takes soil as viscoelastic mass and Theological effect of the interface between diaphram wall and ground into consideration. Its results are compared with those without an interface element, without considering the relative creep displacement. Close attention is paid to the variation of wall with time under the condition of various interface shear stiffness and viscous sliding coefficient, and their effects on the wall bending moment are primarily verified in the paper. The change of wall bending moment with time, trench heave and wall displacement in different excavation depth, bracing position, parameters for soil are also studied.

Jan 1, 2010

By Kento Miyamoto, Kazuki Imamura, Takayuki Tanaka

"Global economic development has drastically increased energy consumption in various fields, and CO2 emissions, which are a prime cause of global warming, have continued to increase. Therefore, measures for reduction of the load on the environment have been taken in various areas. Energy improvements of various types of work vessels used for offshore construction might be expected to greatly reduce consumption of fossil fuel, because many of these vessels are larger than land construction machinery and consume large amounts of fuel, which will lead to effective use of resources and alleviation of the load on the environment. However, such efforts are unusual because renewal or newbuilding of work vessels is rare. We developed a work-vessel hybrid energy system based on fuel-saving technology and use of natural energy to promote reduction of CO2 emissions for a large deep mixing barge in 2010. We developed an Automated Generator Start-Stop System, which automatically controls the number of active generators according to power demand during ground-improving work of the deep mixing barge in 2012, thus further improving the work-vessel hybrid energy system. These systems are introduced here.INTRODUCTIONIn recent years, CO2 emission, which is one of the factors of the Global Warming has been increasing. According to the report by National Institute for the Environmental Studies in Japan (2014), CO2 emission in Japan has amounted to 1,276 million tons. The industrial sector in the total emission becomes 500 million tons that is equivalent to 39%. Meanwhile, the offshore Deep Mixing Method requires work vessels mounted with a large power plant (Fig. 1). In sea ground boring, very large load acts on the deep mixing machine, and the large power is required, which results in the increase in CO2 emission. To achieve eco-friendly marine construction, the work-vessel hybrid energy system was developed. Table 1 shows specifications of the deep mixing barge with the work-vessel hybrid energy system."

Jan 1, 2015

By William F. Loftus

When high capacity diameter pipe piles are driven open-ended into the underlying bedrock, the material gathered inside the pipe often must be excavated to allow concrete to be placed within, in a clean environment. This paper discusses a method of dealing with this ?to be excavated material - the contaminated soil of the Harlem River in New York City, USA.?

Jan 1, 1996

By Scott M. Doehla

A proposed rehabilitation of a 200,000 sf, 75-foot high steel-frame building at the former U.S. Navy Yard in Brooklyn, New York required the review of existing foundation data and an investigation of the foundations with respect to their condition. The building was constructed in stages between 1856 and 1933, including several expansions and interior equipment with isolated foundations. The building has clear spans on the order of 50 feet and at one time supported cranes allowing transport of heavy equipment through the building. The proposed rehabilitation is to include a food manufacturing center and office space having multiple stories. Original construction drawings, available from the Brooklyn Navy Yard Development Corporation?s drawing archive, were reviewed to determine the foundation system supporting the structure. The original drawings provide a window into the methods utilized during late 19th and early 20th century pile foundation construction. The review revealed that the building is supported by pile foundations ranging from timber to concrete-filled steel pipe (depending on the year of construction). Annotations including pile driving records were available on some drawings indicating the design and as-built capacity (using the ENR formula for driving resistance). An investigation consisting of test borings was performed to identify the subsurface conditions underlying the building for evaluating theoretical capacity of the piles. A test pit investigation was performed against existing columns within the structure to expose the piles and pile caps for inspection pertaining to pile condition. The test pit investigation revealed methods utilized during original construction to integrate new columns with existing floor slabs, the use of below-grade brick arches to support a floor slab, and the condition of timber piles which were likely installed up to 120 years ago. The observations made within the test pits were compared with original drawings to evaluate the accuracy of these drawings.

Jan 1, 2008

By Timothy C. Siegel, Paul J. Axtell

The Missouri Department of Transportation (MoDOT) recently replaced the Hurricane Deck Bridge that carries Highway 5 traffic across the Osage Arm of the Lake of the Ozarks in Camden County, Missouri. The former bridge was constructed in the 1920's and was supported on pneumatic caissons bearing on dolostone bedrock. The replacement structure is founded on drilled shafts socketed into the bedrock. During the design phase of this bid-build project, a baseline design was developed and Alternative Technical Concepts (ATC's) were allowed from approved contractors. Those ATC's were confidential and not shared between teams. Either the baseline design or the approved ATC design could be bid by the respective contractors. The baseline design included re-use of the 90-year old caisson foundations. Accordingly, an extensive evaluation of the caissons and underlying bedrock were conducted by coring, laboratory testing, acoustic tele-viewer (ATV), and cross-hole sonic logging (CSL) methods. The results of the investigation indicated the caissons were in excellent condition and suitable for re-use. However, a more cost-effective ATC was submitted, awarded, and constructed that did not re-use the existing caisson foundations but rather reduced the span lengths, increased the number of piers in the water, and supported those piers on drilled shafts. Interestingly, the difference in low bid price between the awarded ATC and the baseline design was less than one percent of the construction cost. This paper describes the multiple foundation designs that were necessary for this interesting project. The various foundation evaluations include the existing pneumatic caissons, large-diameter open-ended pipe piles to support the baseline design, and the design of rock-socketed drilled shafts that were successfully constructed in 2012.

Jan 1, 2017

By Edwin W. Hickey

This paper briefly discusses the geologic conditions in South Florida relative to the design, construction, and performance of deep foundations. The subsurface conditions in this area are unique in that the rock layers are highly porous and often very soft, and are sandwiched between layers of typically loose, uncemented quartz fine sands. Due to the high porosity of the Miami Limestone, 4-inch diameter rock coring is often required to obtain intact samples, and dewatering of excavations is sometimes difficult or impossible. The sand layers, typically tens of feet thick, are very loose to loose in relative density and have been the cause of unexpected large, deep foundation settlements. The engineering properties of the various geologic formations are discussed, along with typical deep foundation types used in the Miami area prior to and after 1980.

Jan 1, 2003

By William M. Camp

Construction-induced earthborn vibrations have long been recognized as a potential problem with respect to the constructed environment and various vibration criteria are in use to prevent damage. A special case of construction vibration control is the protection of early-age or ?green? concrete. Unlike limits for damage prevention to building stock, there is no rational, widely accepted limit for protection of early-age concrete. Numerous criteria have been proposed or reported in the literature and the most relevant and rational proposals are summarized herein. These findings are applied to a case history involving both bored and driven piles. Vibration measurements were made during pile driving activities and the vibration magnitude was evaluated with respect to the exposure of freshly-placed and curing concrete to the earthborn vibrations. The maximum vibration magnitude at the applicable distances from pile driving was on the order of 0.3 inches per second. Based on the most persuasive literature, threshold values of 0.8 inches per second or even 1 to 2 inches per second for the protection of green concrete appear to be well-supported. Consequently, it was concluded that the pile driving activities and bored pile construction could proceed simultaneously.

Jan 1, 2010