Search Documents

By L. Adler

The proper transfer of roof loads from props and bolts to ribs and pillars can result in appreciable savings. The author shows how to plan such load reduction in underground mines. For openings in bedded rocks, analyzed by simple beam theory, it has been shown that roof loads can be shifted from one support to another.&apos; This transfer is effected by controlling the relative deflection of adjacent supports. If this action is used to reduce loads in the props or bolts and increase them in the ribs or pillars, it could be productive of economies averaging 30 pct. Such savings can be realized by: 1) using smaller artifical supports such as props and bolts, and 2) increasing loads in the rib to induce eventual failure for longwall caving. Since the rib is relatively load-insensitive, it provides a natural load sink. However, caution must be used in applying such permissive deflections, for while the supports are being handled properly, the stresses in the roof itself are very sensitive to such manipulations.1 An underground opening overlain by a relatively thin immediate roof, and a thick main roof, is usually laid out as shown in Fig. 1. The total open span (T) between pillars or ribs is calculated on the basis of the main roof, and the secondary spans (L) on the basis of the immediate roof, so that a complete accounting of the existing loads is made. For this purpose the immediate roof is treated as a uniformly loaded continous beam, which is an indeterminate structure as shown in Fig. 2(A). The term systematic supports places the following two restrictions on the continuous beam: 1) Spans between all supports are equal: uniformity of spans. 2) Loads on all supports (excepting ribs) are equal: uniformity of supports. The usual mode of analysis of such a structure by beam theory is to divide it up into a series of simply supported beams with end moments as shown in Fig. 2(B)2 The problem now is to transfer a maximum roof load to the rib from the span immediately adjacent to it by permitting its support to deflect, and yet not fail the roof. Once this has been done, the load can be equalized on all other supports by permitting further degrees of relative deflection. It is necessary, therefore, to determine an expression for the constant load on each support, and the required deflections, in terms of properties of the roof. From Fig. 1: T/L0 = No and T/L = N [1] Where: T = allowable span of main roof, ft. (Calculated from S = Mc/l) S is allowable modulus of rupture, psi. M is maximum moment, lb-ft (in this case wT2/12). c is distance from neutral axis to extreme fiber, ft. I is moment of inertia with respect to the neutral axis, ft4. L,, = allowable span of immediate roof, ft (calculated as was T). L = actual span of immediate roof, ft. N0 and N are pure numbers where No < N and N is the integer just higher than Nu. For example: If T =100 ft and L0 - 15 ft 100 N0 =100/15= 6.667 . . .N= 7 L = T/N = 100/7 = 14.28 ft Consequently N = No + n where n is a positive fraction i.e.: 0< n < 1 Since from Eq. 1, T = NL = N0L0 Lo /L = N/No = N/N-n

Jan 1, 1961

By A. W. Schlechten, R. P. Abendroth

Jan 1, 1960

Low Zinc Prices Close Alcoa Mine Alcoa Mining Co., announced that it will suspend operations at its Hutson mine, near Salem, Ky., because of low zinc prices, January 15. The Aluminum Co. of America subsidiary announced that the low market has made zinc mining un- profitable. About 70 men were employed at the mine, with a production of about 5000 tons of zinc annually. Alcoa said the shutdown would not affect other company operations, with most of the men at Hutson absorbed in the mining firm&apos;s fluorspar operations in the same area.

Jan 2, 1953

By E. Martinez

The effect of ultrasonic energy transmitted through a liquid on chrysotile asbestos was investigated. Ultrasonic energy was effective in fiberization of chrysotile crudes as well as standard grades of milled asbestos fibers. Treated samples of several grades of milled fibers had increased wet bulk volumes and decreased settling and filtration rates compared to untreated fibers. Ultrasonics may be a method for fiberization of chrysotile without decreasing length or use of chemical additives that alter surface properties. Cavitation of the liquid on the surface of fiber bundles is believed to be the cause of the fiberization. It was found that ultrasonic energy greatly increased the rate of precipitation of latex on asbestos. When chrysotile asbestos fibers require additional opening or fiberization, the usual method employed is some type of high speed impact or grinding to open the fibers and produce a larger surface area. These methods always cause some degradation in length due to breaking of fibers. In addition, the efficiency of mechanical methods decreases as the diameter of fiber bundles decreases. Chemical methods have been proposed and it is claimed that fiberization down to individual fibers of 200-300 A diam is possible with some wetting agents. However, large amounts of reagent are required, approximately EDWARD MARTINEZ is with Central Research Laboratories, American Smelting and Refining Co., South Plain-field, N.J. TP 63H226. Manuscript, Aug. 12, 1963. Discussion of this paper, submitted in duplicate prior to Mar. 15, 1964, will appear in SME Transactions, September 1964, and AIME Transactions, 1964, vol. 229. 50 pct of the weight of fiber treated, and some of the wetting agent remains on the surface of the chrysotile and cannot be removed by any solvent which does not destroy the asbestos.&apos; This investigation was directed at determining whether ultrasonic energy transmitted through a liquid would be effective in fiberizing chrysotile asbestos. Samples of asbestos crudes and commercially milled fibers were treated; settling and filtration rates of treated and untreated milled fibers were obtained. EQUIPMENT A Westinghouse Corp. ultrasonic cleaning system WEHH was used in this investigation. See Table I for a breakdown of this ultrasonic unit. RESULTS AND DISCUSSION Fiberization of Chrysotile Crudes: Samples of chrysotile crudes were pulled apart with tweezers so that coarse bundles of fiber approximately 1/16 in. in diam were obtained. The bundles were put into a bottle with 200 ml of methanol and the mixture placed into the ultrasonic tank for 30 min at a power output of 1200 w. The test was repeated using water instead of methanol. During the irradiation it was noted that the surfaces of the bundles were being fiberized. The liquid eventually became cloudy with dispersed solids. Fig. 1 is an electron micrograph of the fibers, some reduced to unit dimensions, and a fine material released by the ultrasonic energy. The platy particles in Fig. 1 were identified by electron diffraction and differential thermal analysis as brucite, Mg(OH)2, which must have been intergrown in the chrysotile crudes. Electron micrographs of bulk specimens of chrysotile have shown a fine material filling the interstices between tubular fibers.2,3 Electron diffraction patterns of the fine material collected after ultrasonic treatment indicate that it is amorphous. After decanting the solution, bundles of chrysotile remained somewhat decreased in diameter. Continuing the ultrasonic irradiation of the remaining material resulted in additional fiberization. The opening of the fibers occurred in both methanol and water. Cavitation of the liquid by the ultrasonic energy is undoubtedly responsible for the fiberization. When sound waves are transmitted through a liquid at a

Jan 1, 1963

By S. E. Bretherton

This title introduces the subject I wish to describe to my fellow members, very few of whom, I &apos;hope, have ever had as much trouble with the smelting of ore containing much zinc, either in the lead blast furnace or the matting furnace, as circumstances have forced upon me: First, for several years in Leadville, Colo., after the sulphide ores containing zinc had been developed with greater depth and were sold to the intereats with which I was connected for smelt-ing in the blast furnace for the recovery of the lead, silver, and gold; then, in New Mexico and Arizona, where the principal source of ore supply for our custom smelter was from miners who sent most of their product in the form of concentrates, which we briquetted and smelted in the blast furnace, producing a matte containing copper, silver, and gold, for which we were paid; together with some zinc and lead, which was penalized if in excess of a maximum base set by the refinery to which we sold our copper matte; last, but not least, my experience in Shasta county, Gal., where for the sake of recovering $13 per ton value in copper, silver, and gold, I have smelted ore containing as high as 40 per cent. zinc (the last 18,951 tons smelted averaged 15 3/10 per cent. zinc) which we not only lost, but which it cost us money to lose. After such an experience, and knowing that, instead of being worth only $13 per ton, such 15 per cent. zinc ore should be worth about $30, including zinc at the present market value, the question of recovering the zinc in a profitable manner from such ore became very interesting to me. During several years&apos; time I sent samples, of from 5 to 1,200 lb. each, to be tested by the different best-known zinc-recovery plants, and experimented with several processes proposed by others for the treatment of such ore, with but little encouragement, until I

Jan 1, 1914

By R. M. Goldhoff, J. W. Spretnak, R. Speiser

IT has been observed by Grange and Garvey&apos; that the homogenization of boron-treated steels could lead to complete elimination of the hardenability effect caused by boron. The experimental conditions leading to this conclusion involved the heating of steel specimens with and without boron at 2350°F for 24 hr. To prevent oxidation and decarburization, the specimens were encapsulated under vacuum in silica tubes. This observation of permanent deterioration of boron effect was noted in both a 0.63 pct plain carbon steel and a 0.25 pct C low alloy steel, both of which had been treated with ferroboron and homogenized at 2350°F for 24 hr. In another series of boron-treated steels which had been homogenized for shorter times, the effect was to reduce, but not completely eliminate, the boron effect. Under these circumstances, it was presumed that longer heating times would cause permanent deterioration of the boron effect in this series of steels also. Since the characteristic grain boundary constituent could not be formed in any of these steels after homogenization, it was concluded that possibly boron was being converted into an ineffective form through chemical combination resulting from prolonged heating at high temperatures. Assuming the validity of this observation, a series of experiments to establish the relationship between temperature of homogenization and kinetics of deterioration was contemplated. Initially an attempt was made to reproduce the results just described. For this purpose commercial lots of AISI 8640 and AISI 86B40 steels were used. The analyses of these steels appear in Table I. Hardenability evaluation was on the basis of the hardness of normalized sections. Grange and Garvey&apos; pointed out that these steels are air hardening to some extent and such a technique can be used. For these tests the specimens were held for 20 min in a salt bath at 1600°F and then cooled in still air. Several evacuated silica capsules containing pairs of the test steels were made up and heated for 24 hr at 2350°F. A number of failures occurred among these capsules, but evaluation of the specimens successfully treated indicated a complete deterioration of the boron effect. However, examination of the surface of the treated specimens showed that some reaction, probably with the silica tube, had taken place, since none of the specimens was bright. One further test was made at 2350°F for 12 hr, using a pair of specimens wrapped in tantalum foil prior to encapsulation. These specimens appeared bright after treatment, and their hardenability evaluation showed that no deterioration had taken place. Since these steels are extremely sensitive to de-boronization at high temperatures and particularly at long times of holding, the experimental observations raised some doubt as to the real occurrence of the permanent deterioration effect. To resolve this question an experiment was undertaken in which the high temperature portion of the treatment was completed in vacuum. For this purpose a molybdenum wound resistance furnace capable of maintaining good vacuum was used. All the pertinent accessories to this furnace were machined from molybdenum stock in order to withstand the high temperature involved in the experiment. With this equipment a temperature of 2400 °F was obtained and held under a pressure of 5x10-" mm Hg for 24 hr. A specimen of each of the two test steels was suspended in the furnace and both were heated simultaneously. Temperature was measured with a standardized Pt—Pt-13 pct Rh thermocouple, whose millivoltage at 2400°F was extrapolated from the standardization equation, good up to 2200°F. The complete evaluation of these specimens is shown in Table 11. The hardness values attained by each steel after normalizing, both before and after the prolonged high temperature treatment, remain the same. A microscopic study of the decomposition products present in the microstructures of specimens at various points in the heat treatment correlated with the hardness values observed. It seems that no permanent loss of boron hardenability effect occurs, at least in these Grainal-treated steels, when deboronization is circumvented. Acknowledgments This work was conducted under the sponsorship of the Aeronautical Research Laboratory, Wright Air Development Center, under Contract No. AF 18(600)-94, and their support and permission to publish is gratefully acknowledged. A note of thanks is also extended to the Republic Steel Corp. for supplying the materials used in the work. References &apos; R. A. Grange and T. M. Garvey: Factors Affecting the Harden-ability of Boron Treated Steels. Tro.ns. ASM, 1946, vol. 37, p. 136.

Jan 1, 1957

By Jasper L. Stuckey

PYROPHYLLITE, first identified as soapstone,1 later as agalmatolite,2 and finally as pyrophyllite,3 has been known to occur in North Carolina for more than 130 years and has been produced intermittently in commercial amounts for the past 100 years. Pyrophyllite mining, however, has become a major industry in North Carolina only during the past 25 years. North Carolina and California are the chief producing states. Current annual production averages 125,000 tons, of which slightly more than 90 pct comes from North Carolina. Distribution and Geologic Setting: All known pyrophyllite deposits in North Carolina are associated with rocks of the Carolina Slate Belt,4 which is composed of a vast series of metamorphosed volcanic and sedimentary materials, occurring as two zones extending in a northeast-southwest direction across the state. The larger of these zones, lying in the central Piedmont region, varies from 8 to 50 miles wide. The smaller zone lies along the eastern edge of the Piedmont region and is partly covered by coastal plain sediments.

Jan 1, 1958

By Kenneth F. Whinery, John M. Campbell

Basically, the Buckley-Leverett theory involves two systems which are similar in nature but are differentiated by time. These systems may be described by the fractional flow and frontal advance equations which essentially characterize the mechanics of oil movement while being expelled from the reservoir. The fractional flow equation originally developed by Leverettl may be expressed in the more usable form The development of this equation is based on Darcy&apos;s law describing fluid flow through porous media and applies to the flow at only one point (it is a point function). For simplification, the fractional flow equation is written in the above form because the capillary forces always increase the fractional flow of the displacing phase regardless of the direction of flow or the displacing phase. If, for simplicity, the effects due to gravity and capillary pressure differences are neglected, the fraction of the displacing fluid, f, at any point in the flowing stream is related to the properties of the system by 1 Thus, it is seen that in the absence of capillary and gravitational effects, fd for a given sand and fluids varies only with saturation and pressure. The magnitude of the viscosity ratio, —a has an effective range (range of about 30) in the system where gas is displacing oil and a much smaller range for water displacing oil. In order to make the fractional flow equation more versatile, it is necessary to connect the fractional flow at a given point and saturation with time. This problem was approached by Buckley and Leverett" who developed the frontal advance equation, Eq. 3 states that the rate of advance of a plane that has a fixed saturation, Sd, is proportional to the change in composition of the flow stream caused by a small change in the saturation of the displacing fluid. It is, essentially, a transformation of a material balance equation representing the net rate of accumulation of the displacing phase within a homogeneous sand block. This accumulation is proportional to the difference between the rate at which the displacing fluid enters the sand and that at which it leaves. Eq. 3 describes the velocity with which a plane of constant displacing phase saturation advances through a porous system. Buckley and Leverett," Babson,&apos; Kern," Welge, and others have adequately discussed the basic mechanism and application of the fractional flow and frontal advance equations. APPLICATIONS OF THE FRONTAL ADVANCE THEORY TO PETROLEUM RECOVERY Two general applications of the Buckley-Leverett frontal advance theory involve the system in which the oil is being displaced by an expanding gas cap overlying the oil zone and that in which the oil is being displaced by water. Displacement by Gas in the Presence of an Immobile Water Saturation A system in which gas is the displacing phase may be thought of as having two forces effecting the displacement process. These forces are the gravitational force and that force exerted by the displacing gas. The gravitational effects control the displacing efficiency of the gas. The gravitational effect will be less at higher rates of flow, thereby reducing the effectiveness of the displacement of the oil by the gas. The more efficient displacements occur at flow rates which are less than the gravity free fall rate. Capillary forces can be neglected without materially changing the magnitude of the gas saturation. The Mile Six pool is used herein to illustrate the calculating procedures in evaluating gas drive-gravity drainage field perfomlance. These calculations represent the determination of the gas-oil contact when the distribution of the hydrocarbon pore volume is considered. Two methods

By James M. Link

Slurry transport of industrial minerals has proven to be practical, economical, and efficient. Industrial minerals currently being pumped for long distances include cement, clay, phosphate, sand, and various waste product from industrial mineral processing operations. This paper will touch upon the basic theory of hydraulic transport of solids and then consider the economic and engineering considerations upon which construction and operation of such a line would be based. Where possible, actual cost data will be presented.

Jan 1, 1974

By K. C. Ko, D. A. Pifer

The theory of probability with respect to the failure of structures is discussed. It is shown that the probability of safety, probability of failure, and factor of safety are directly related to each other and that as standard deviation approaches zero, the probability curves approach a unit step function which can be interpreted as the conventional factor of safety. The factor of safety is numerically the ratio of the load to the strength of the material at a particular point or plane in an engineering structure. Mathematically, it can be illustrated as a unit step function undefined at the point where the factor of safety is one (Fig. 1). The uncertainty of variation of soil and rock strengths require factors of safety much higher than those used in other engineering structures. The factors of safety used are generally determined from past experiences with similar structures. However, the factors thus determined do not have any theoretical meaning or do not indicate any relationship to actual safety.&apos; It seems, therefore, logical to develop a system with a sound theoretical basis to obtain a more suitable factor of safety for structures. An application of elementary theory of probability indicates that it is possible to relate this number to theoretical and practical engineering facts.

Jan 1, 1971

By F. A. Olson, S. L. Pohlman

A unique method of measuring weight loss as a function 3 of time, with a sensitivity of 10-5 grams, while leaching copper minerals with a flowing acid leach solution has been developed. Kinetic results obtained coupled with visual and microprobe analyses show topochemical reaction for the leaching of chrysocolla with sulfuric acid. The kinetics follow a shrinking core model and show ion diffusion through a product layer, chemical reaction at the unreacted core interface and mass transfer through the boundary layer as being important.

Jan 1, 1974

By J. J. Forbes

Probably the newest thing in mining safety, or safety for mines, is the apparent dissatisfaction on the part of the mineral industries, as represented by both management and labor, and the general public of the Nation, with the safety record of the mining industry. This is reflected by published comments and papers in the technical press;1-8 in labor periodicals, 10 11 in popular journals and periodicals,12 13 and in the daily press; also by discussions of the Safety Committees sponsored by the National Safety Council, 9, 14-15 the American Mining Congress, 1, 16 the American Institute of Mining and Metallurgical Engineers, 2, 4 the Mine Inspectors&apos; Institute of America,6,8,17,18 the Coal Mining Institute of America, 5, 19, the American Standards Association, and others.20,21

Jan 1, 1949

By C. A. Allen

For over three years we have been endeavoring to reduce the number of fatalitics and minor accidents in Utah. The physical condition of the FIG: 1.—Number kiLlEd per million short tons of coal produced in ColoraI)o, New Mexico, utah, Wyoming, and bituminous mines of the United States 1014 to 1920. mines, concentrators, and smelters is good, yet the number of accidents,

Jan 1, 1923

By C. A. Allen

For over three years we have been endeavoring to reduce the number of fatalitics and minor accidents in Utah. The physical condition of the FIG: 1.—Number kiLlEd per million short tons of coal produced in ColoraI)o, New Mexico, utah, Wyoming, and bituminous mines of the United States 1014 to 1920. mines, concentrators, and smelters is good, yet the number of accidents,

Jan 1, 1923

By Eugene Stephenson

CRITICAL analyses of the work expended in producing oil by the utilization of gas energy have appeared in the publications of Shaw,1 Pierce and Lewis,2 and Herold,3 authors who have ably discussed the factors which must be taken into consideration in comparing energy consumed per barrel in various wells which are flowed by means of gas-lift. However, two distinct phases of oil production are concerned with the ratio of gas energy consumed to oil produced. One of these phases is the gas-lift, which utilizes the differential gas pressures for the purpose of flowing oil, whether these pressures be natural reservoir pressures or be induced by artificial compression of gas or air. The other phase has to do with prorating oil production in pools which are operated either as units, or are subject to such restrictions as those imposed at Oklahoma City by the Corporation Commission, or, by similar controlling groups in other fields. An abundance of literature is available relative to the problems of flowing wells by gas-lift, but the first suggestion that the energy of the gas within the oil and gas pool might serve as a basis for proration, appeared in the timely article by McWilliams.4 Much of the. dissatisfaction with proration in certain fields is because some operators feel that besides the hazard to the wells which accompanies the test, the method of allocating production on the basis of the "potential" gage is inequitable and gives some operators a distinct advantage over others.5 The most severe penalty may be exacted from the most progressive operators or those who attempt to produce their oil with a minimum quantity of reservoir gas. If :no difficulties ever

Jan 1, 1931

By E. A. Gulbransen, J. W. Hickman

DURING the past two decades considerable progress has been made in the art of manufacturing heater alloys. The conventional iron-chromium-nickel alloys have been improved by the addition of small quantities of other elements. Up to the present time, to our knowledge, there has not appeared a systematic study of these alloys where the newer tools of investigation have been brought to bear on the problem. It is not yet clear what roles the additional elements play in increasing life time in usage. As a first approximation one might guess that elements such as manganese, silicon, zirconium, calcium and aluminum would aid in the formation of a protective film on the alloy surface, thus retarding the oxidation rate and increasing lifetime. If these additional elements do form protective oxides in the outer surface of the oxide film, it may be possible to identify them by means of reflection electron diffraction. It is also possible that the additional elements may not diffuse to the surface but may remain at the interface between the oxide and the metal. Then, too, the major elements in the alloys undoubtedly form oxides which are stratified on the surface. If the minor elements concentrate in a layer in contact with the substrate where they undergo oxidation and if this oxide film offers resistance to the diffusion of iron, chromium and nickel ions, then the lifetime of the heater element might be expected to increase. It is also possible that preferential reduction in the diffusion rates of the several ions may Occur to such a degree that oxides may form in the body Of the film and On the outer surface which are different from those that would normally form if the additional elements were not present. The use Of transmisson electron diffraction may aid us in jnterpreting these phenomena. UP to the Present time all Of the factors which influence the lifetime of a given heater element are not definitely known. Among these are: (I) The rate of oxidation of the alloy. This may be dependent upon the composition and the physica1 state of the "alloy. (2) The stability of the structure of the coating which forms. Transitions from one structure to another or solid phase reactions resulting in a change of composition may occur. The tendency of the film to adhere to the substrate when heated and cooled successively will be important. (3) The evaporation of various constituents from the alloy such as the remova1 of carbon by Oxygen in a decar-burization reaction. With these possibilities in view, an electron diffraction study of the oxides occurring on six different nickel-chromium alloys was undertaken with the hope that the results of this study could be correlated with oxidation rate studies as determined by means of the vacuum microbalance method1 and with lifetime tests carried

Jan 1, 1949

By R. E. Hummel, J. W. Koger

IT is generally accepted that the martensitic start temperature (Ms) can be determined by resistivity measurements and is that temperature where the resistivity vs temperature curve on cooling first deviates from a straight line.1-4 Both Titchener and ever&apos; and pops5 have used resistivity measurements to follow the martensitic transformation in b1 Cu-Zn and ternary Cu-Zn-based b-phase alloys, respectively. Actually because of the nature of their measurements the temperature of minimum resistivity (M) was used by these authors to determine "Ms" . Also, due to experimental difficulties in detecting M, with resistivity measurements, Pops and Massalski 8 determined M, by optical microscopy. The present communication is concerned with high-precision, low-temperature resistivity measurements which reveal a definite M, temperature which differs from the temperature of minimum resistivity (M). It is also shown that M is merely the result of the geometry of the percent-transformation curve and the temperature coefficient of resistivity of the alloy. In other words, it will be demonstrated that M has no apparent significance (except that it denotes a temperature at which some percent of martensite can be detected in a given alloy). Alloy specimens were made by melting 99.999 pct Cu and 99.9999 pct Zn in sealed and evacuated quartz tubes and homogenizing them at 601PC for 300 hr. After the alloy was cold-rolled into foils suitable for resistivity measurements, it was quenched in ice water from 871PC. The chemical analysis showed a zinc content of 38.8 wt pct. The cooling rate during the martensite transformation was 1°C per min and was controlled with a thermistor. Electrical resistivity measurements were made using a K-3 type potentiometer; the reproducibility of the resistivity values was better than 0.03 pct. Temperatures were measured with a thermocouple to an accuracy of better than 0.2° C. Fig. 1 shows the resistivity vs temperature curves of the martensitic transformation in B1 Cu-Zn for both cooling and heating. The starting point of the martensitic transformation (M,) was taken as that

Jan 1, 1968

By G. Thodos, R. B. Grieves

A method has been developed for the accurate calculation of the cricondentberm and cricondenbar temperatures of multicomponent hydrocarbon mixtures of known composition. The mixtures may contain any number of components including paraffins and isoparaffins, olefins, acetylenes, naphthenes and aromatics. This approach is based upon the mole fraction of the low-boiling component in the mixture and graphically presents the ratios of the cricondentherm and cricondenbar temperatures to the pseudocritical temperature as {unctions of a boiling-point parameter. The only requirements are the critical temperature, normal boiling point and the approximate vapor pressure behavior of each component. For mixtures of more than two constituents a stepwise calculation procedure is necessary where the pseudocritical temperature is based upon the critical temperature of the pure low-boiling component and upon the actual cricondentherm or cricondenbar temperature of the mixture of all the remaining higher-boiling components. From an analysis of 22 binary systems (123 compositionsl, the average deviation of calculated cricondentherm temperatures from reported values is 0.87 per cent, based on degrees Rankine; and for 10 multicomponent mixtures containing from three to six components, the average deviation is 0.98 per cent. From an analysis of 18 binary systems (104 compositions) the average deviation of calculated cricondenbar temperatures from reported values is 0. 79 per cent; and for 15 multicomponent mixtures, 1.47 per cent. Equations, derived from the graphical relationships, are presented which enable rapid calculations for both binary and multicomponent systems. INTRODUCTION With the increasing tendency towards the use of high pressure processes, the need for an accurate method of calculation of the properties of a multicomponent hydrocarbon mixture in the critical region is becoming more essential. Critical region phase relations are also significant in gas condensate reservoirs, for which a knowledge of the fluid phase boundaries and regions of retrograde condensation make it possible to evaluate optimum operating conditions. The possibility of liquefaction in the underground structure may be established, and information on the feasibility of the use of repressurizing may be determined. A typical phase diagram for a multicomponent hydrocarbon mixture is presented as Fig. 1. This figure also shows the regions of retrograde behavior encountered by following lines AB and AC. If accurate methods of calculating the temperatures and pressures at the critical, cricondentherm (maximum temperature) and cricondenbar (maximum pressure) points of multicomponent hydrocarbon mixtures of known composition were available, it would be possible to estimate closely the entire phase diagram of any mixture. Several methods have been presented in the literature for the estimation of the critical temperatures and pressures of multicomponent mixtures containing all types of hydrocarbons and including the fixed gases.4-8,21 Considering the cricondentherm and cricondenbar points, the work is more limited. Etter and Kay5 have developed rather complex equations for

By T. Sekimoto, T. Kokubo, M. Yamamoto, K. Masuda, T. Moro, H. Sakamoto

The choking-free cyclone was developed primarily to remove solid particles suspended in a slurry containing fibrous materials, such as municipal solid waste. This cyclone is characterized by a screw conveyor at the underflow side of the cyclone. The screw conveyor has a hollow rotational shaft for air supply and is driven by a variable speed motor for discharge control. Even if the underflow discharge is highly concentrated, this type of cyclone can be stably operated without nozzle choking. High classification efficiency similar to that of a conventional cyclone can be obtained as a result of air introduction through the hollow rotational shaft. The recovery of organic matter and the removal efficiency of inorganic matter were actually improved by the application of this cyclone to municipal solid waste. After applying this cyclone to the desliming of fine sand, sand product of low water content was recovered.

Jan 1, 1980

By T. O. Allen, J. H. Atterbury

Laboratory and field tests during the past five years indicated considerable variation in the penetrating power of commercially available gun perforators. Many of the guns which achieved inadequate penetration in these tests have since been improved. However, recent productivity tests indicated the possibility of inadequate penetration or, at least, ineffective penetration in some wells. Laboratory experiments under simulated well conditions have demonstrated considerable plugging of the perforations, apparently as a result of factors associated with the shooting process and/or the drilling mud in the well at the time of perforating. The restrictions to flow per unit of hole depth caused by this plugging appears to be greater for jet perforators than for bullet guns of comparable diameter; however, because of the greater depth of penetration obtained with the jet guns, the total flow rates appear to he approximately equal. Limited testing with an experimental shaped charge suggests that less shot hole restriction and greater flow rates may result from larger-diameter perforations or other factors related to charge design. INTRODUCTION Gun perforating has been accepted for a number of years as a routine well completion method which is often preferred since it permits more selective operation of producing zones. Nevertheless, questions have continued to arise as to the effectiveness of the communication paths established between the productive formation and the interior of the casing. The basis for these questions has generally been failure to obtain anticipated fluid production rates through gun perforated completions in specific wells. These low productivities, together with the frequent recovery of bullets from well bores, were considered strong evidence of inadequate penetration. Laboratory investigations of the penetration performance of many of the bullet guns available as late as 1948 gave support to these indications. Subsequent electrical analog studiesl,2,3 indicated that the depth of penetration required to provide productivities equivalent to open hole was beyond the capacity of most bullet perforators evaluated in the early laboratory penetration tests. These results, together with the advent of the shaped charge in the field of oil well perforating, stimulated the interest of both oil operators and service companies in gun development. Improvements in gun design resulted in jet and bullet guns which appeared to be capable of providing sufficient penetration for most perforating jobs. However, some wells failed to yield satisfactory fluid production even after being perforated with the more powerful guns, again raising the question as to the effectiveness of the perforating operation. This fact, together with preliminary shooting into targets prepared with formation cores, indicated that factors associated with the perforating process and/or the fluids in the well bore at the time of shooting may reduce effective formation penetration and thereby decrease well productivity. These laboratory and field data prompted another phase in the investigation of the effectiveness of gun perforating: a program to determine the extent and seriousness of perforation plugging under simulated well conditions.

Jan 1, 1955