Search Documents

By R. G. Turner, M. G. Hubbard, A. E. Dukler

Gas phase hydrocarbons produced from underground reservoirs will, in many instances, have liquid phase material associated with them, the presence of which can affect the flowing characteristics of the well. Liquids can come from condensation of hydrocarbon gas (condensate) or from interstitial water in the reservoir matrix. In either case, the higher density liquid phase, being essentially discontinuous, must be transported to the surface by the gas. In the event the gas phase does not provide sufficient transport energy to lift the liquids out of the well, the liquids will accumulate in the wellbore. The accumulation of the liquid will impose an additional back pressure on the formation that can significantly affect the production capacity of the well. In low pressure wells the liquid may completely kill the well; and in the higher pressure wells there can occur a variable degree of slugging or churning of the liquids, which can affect calculations used in routine well tests. Specifically, the calculated bottom-hole pressures used in multirate backpressure tests will be erroneous if the well is not removing liquids on a continuous basis, and gas:liquid ratios observed during such a test may not be correct. Several authors1,3,8,14 have suggested methods to determine if the flow rate of a well is sufficient to remove liquid phase material. Vitter14 and Duggan' proposed that wellhead velocities observed in the field would be adequate for keeping wells unloaded. Jones8 and Dukler3 presented analytical treatments resulting in equations for calculating, from physical properties, the minimum necessary flow rate. An analysis of these studies indicates the existence of two proposed physical models for the removal of gas well liquids: (1) liquid film movement along the walls of the pipe and (2) liquid droplets entrained in the high velocity gas core. Although there probably is a continuous exchange of liquid between the gas core and the film, they will be treated separately for the purposes of this study. The development and comparison of these separate models with experimental data will permit the determination of which, if either, is the controlling mechanism for the removal of liquids from gas wells. The Continuous Film Model Liquid phase accumulation on the walls of a conduit during two-phase gas/liquid flow is inevitable due to the impingement of entrained liquid drops and the condensation of vapors. The movement of the liquid on the wall is therefore of interest in the analysis of liquid removal from gas wells. If the annular liquid film must be moved upward along the walls in order to keep a gas well from loading up, then the minimum gas flow rate necessary to accomplish this is of primary interest. The analysis technique used follows Dukler2 and Hewitt5 and involves describing the profile of the velocity of a liquid film moving upward on the inside of a tube. The minimum rate of gas flow required to move the film upward is then calculated.

Jan 1, 1970

By W. C. Lacy

This article is a progress report of a program designed to quantitatively evaluate geological parameters to predict stable slope angles. The author feels that, although there does not appear to be any one technique or characteristics that will suffice as an index to the determination of stable slope angles, a combination of seismic methods as outlined here, detailed geological mapping and logging of core, and a better understanding of the angle of internal friction in rock types will permit accurate estimation. A mining engineer friend once remarked, "If we don't have pit slope failures, the slopes are too flat." Since economic justification of an open pit project is based upon ultimate pit slopes, we cannot wait until the pit is developed and slopes established by trial and error. Some combination of geological and/or geophysical techniques must be developed to permit accurate prediction of stable slope angles and to suggest modification of pit outlines to result in slopes enabling maximum economic yield. This presentation is a progress report of a program designed to quantitatively evaluate geological parameters to predict stable slope angles. The principle of the weakest link applies to any slope stability evaluation and necessitates detailed geological examination and recording of observations. Physical failure will occur along any surface where shearing stress exceeds shearing resistance. Rock conditions are seldom uniform even within a single cut or pit face, so stability conditions will vary. Consequently, both plan outline and ultimate slope limits must be tailored to the specific situation. Economic advantages to be gained by slight increases in slope angles in deep pits are well recognized and stimulate efforts to obtain maximum permissible slope angles. MECHANICS OF SLOPE FAILURE Excellent reviews on the nature of slope failure have been presented+2,6,8,11 For the purpose of this study, the writer considers failure to take place by one or more of three processes: 1) ravelling, 2) translation or slope failure, and 3) rotation or base failure (Fig. 1). The effects of increased pore water pressure in soils were recognized in 1923 by Terzaghi in his development of the concept of effective stress, and he has applied the same principle to jointed rocks designating water pressure as cleft-water pressure.8 Cleft-water pressure in a rock slope reduces normal pressure on the plane of failure, thus reducing shearing resistance and resulting in slope failure. In the following discussion it is assumed that adequate drainage is supplied to prevent any build-up of water pressure. This is the first step in any program to establish maximum slopes. Ravelling: Ravelling occurs in rocks with low cohesion and entails the free movement of individual fragments ranging from single rock falls to running ground. Removal of lateral support wherever slope angle exceeds the angle of repose of the rock parti-

Jan 1, 1963

CORPORAL SHEPPARD B. GORDY Sheppard B. Gordy, a brief biography of whom was printed inn the January Bulletin, entered the employ of the Braden Copper Co. immediately on his graduation from the Sheffield Scientific School in 1912. He remained with this company four years, working up through the various grades to assistant foreman and foreman to one of the individual mines. The last year he was in its employ, he acted as general mine foreman. He was for a short time with the Chile Exploration Co. and then went with the Andes Exploration Co. (Anaconda) and remained with CORPORAL SHEPPARD B. GORDY. the latter, doing mine exploration and development work, until he sailed for home in June, 1918, to give a more personal and active service to his country in her need. He declined a tender of induction into an officers' training camp, at the urgent request of Professor McClelland supplemented by Mr. Potter, because they demonstrated to his satisfaction that he could give more valuable service to his country in helping out with the aircraft production. Being within the draft age, in order to carry out this plan, it was necessary for him to be called by his Local Board and sent to camp. This call came Aug. 26. Two weeks before that time lie had gone to Dayton, Ohio; to begin the study of aircraft production, and was sent by the Dayton Board to Camp Sherman, Chillicothe, Ohio, where he died of pneumonia on Oct. 9.

Jan 3, 1919

By L. A. Panek, F. D. Wang, M. C. Sun

A method of stability analysis of underground opening by the limiting equilibrium approach is presented. The Coulomb shear failure criterion is employed to find possible fracture surfaces and to evaluate the shear strengths along them. The normal stresses required for the calculation of shear strength, and the shear stresses for the calculation of total shear force along the fracture surfaces, are obtained by the finite-element method of plane-strain analysis. The factor of safety against Coulomb shear failure is calculated as the ratio of the shear strength to the shear force along a fracture surface, similar to the practice in slope stability analysis. Four shapes of openings are analyzed, with three ratios of horizontal lithostatic stress and four coefficients of internal friction. The critical fracture surfaces found by this method of analysis are consistent with the arching of roofs and slabbing of ribs commonly observed.

Jan 1, 1972

By M. Mortada

Nonsteady-state flow of slightly compressible liquids in porous media of non-uniform properties has been the subject of a number of recent studies. Most of these studies considered one-dimensional flow in systems with cylindrical geometry and with the properties of the porous medium varying with radial distance only. A. Houpeurt' studied the problem in its general form by examining the solutions of the differential equation, In Eq. 1, the permeability k and the porosity + are arbitrary functions of radial distance. Houpeurt concluded that, except for special forms of the functions k and the problem is not well suited for mathematical treatment, but lends itself to high-speed digital computation. Carslaw and Jaeger' discussed the solution of Eq. 1 for the case in which the permeability varies as a power of the radial distance. P. Albert3 studied analytically the pseudo steady-state solutions in systems of finite radial extent and non-uniform properties. He also obtained some numerical solutions for nonsteady-state flow using a high-speed computer. William Hurst4 examined the interference pressure drop due to a point sink located in an infinite system consisting of two permeability regions in series. In this case, the permeability changed at a radial distance r from the point sink. INTERFERENCE BETWEEN OIL FIELDS IN A NON-UNIFORM AQUIFER The interference pressure drop for oil fields located in an extensive aquifer of uniform properties is discussed in a number of places in the literature. This work considers the interference pressure drop for oil fields located in a non-uniform extensive aquifer comprising two regions of different properties as shown in Fig. 1. Region I of the aquifer extends from which is the radius of Oil Field A, to ar,,, where a>1. It has permeability k,, porosity +, and effective compressibility c,. Oil Field B is located in Region II which extends from ar, to infinity and has different properties from those of Region I, but the same formation thickness h. Region II has permeability k2, porosity and effective compressibility c2. The choice of this type of aquifer should not imply that it is of frequent occurrence. It is chosen primarily to illustrate the effects of non-uniform aquifer properties on oilfield interference. It is of interest to point out that a non-uniform radial aquifer in which both the permeability and the porosity are inversely proportional to the radial distance can be treated in a manner similar to a linear aquifer of uniform properties. The situation where only the permeability varies as the inverse of the radial distance is also amenable to analytical treatment. Both aquifers behave quite differently from a radial aquifer with uniform properties so far as the water influx and the interference pressure drop are concerned. METHOD OF SOLUTION The expression for the interference pressure drop in Oil Field B due to a constant rate of water influx in Oil Field A is developed in the Appendix. This is accomplished by the simultaneous solution of two partial differential equations describing the pressure in Regions I and 11. The two differential equations are solved subject to the following conditions: (1) at r,, the pressure gradient is constant; (2) at ar the pressure and

By E. P. Abrahamson II

The effect of transition elements which form binary solid solution upon the recrystallization temperature of zirconium has been investigated. All additions raised the recrystallization temperature. A correlation is obtained between the logarithm of the rate of change of recrystallization temperature with atomic percent solute and the free atom ground state electron configuration of the solute element. ThE work of Abrahamson, et al., on dilute binary solid-solution alloys indicated a correlation between the free-atom ground state electron configuration of the solute and either the brittle-ductile transition or recrystallization temperature. These studies were carried out on bcc base materials. The implication is that the outer s and d electrons of the solute are the prime determinant of the absolute rate of change of recrystallization or transition temperature. Furthermore, the limit of linearity has been shown to be a function of solute electron configuration for recrystallization in iron and vanadium. To date no Complete systematic recrystallization study of dilute binary zirconium base alloys has been made. It is the purpose of this study to note whether the change in solvent structure from bcc to hcp will influence the correlation. It was also desired to learn more of the role of the electron configuration of the solvent on recrystallization temperature. PROCEDURE All alloys were made using 99.87 pct Zr with 0.01 Cr, 0.04 Fe, 0.006 Hf, 0.003 Mg, 0.003 Mn, 0.003 N, and 0.080 0 (132 BHN). The solute elements were 99.9 pct pure. According to the published binary phase diagrams6 and metallographic examinations at X750, all alloys used were solid solutions. The alloys were arc melted and remelted six times in the form of cubic 200-g buttons under an argon atmosphere. They were then hot pressed at 950°C to 0.450 in., upset pressed to 0.350 in., and annealed at 800°C for 1 hr. The specimens were then Blanchard ground to 0.250 in., removing 0.050 in. from each side. The grain size of the material at this stage was found to be 8000 100 grains per sq mm. The specimens were then cold rolled to 0.130 in. and cold pressed to 0.125 in., yielding 50 1 pct cold work. All alloys were then chemically analyzed for the principal addition. The interstitial contents remained at the values of the starting material when checked on random alloy specimens. The rolled sheet was cut into 6.75 by 0.25-in. lengths and heat treated in a gradient furnace for 1 hr. The gradient was 250o to 900°C over the 6-in. length, recorded continuously by six thermocouples resting on each specimen. Control was 3oC, accomplished at the hot end. The recrystallization temperature was determined metallographically using polarized light. The criterion chosen was the point on the specimen showing the first recrystallized grain at a constant magnification, X200. Specimens were repeated, and the agreement was found to be 3°C. RESULTS Three different pure zirconium specimens were tested, and the recrystallization temperature was

Jan 1, 1962

By H. Warlimont

In recent investigations of the microstructure and crystallographic features of martensite by electgon microscopy,', '9 thin films (about 50 to l000A in thickness) have been used as specimens. It was found by W. Pitschl ,2 that the lattice relationships between the supefiaturated fcc matrix and the martensite formed in thin films were different from those observed after transformation in bulk material. Corresponding differences are to be expected in nucleation and in reaction kinetics in the formation of martensite in thin films, but have not yet been reported. In the course of the preparation of thin films of iron-base alloys for investigation by electron microscopy it was observed that films of alloys, whose martensite formation temperature (Ms) was below room temperature, formed martensite during the electrochemical thinning process conducted at or above room temperature. The chemical compositions and approximate bulkM,-temperatures of the three materials on which this observation was made are listed in Table I. The alloys were vacuum-melted from high-purity metals. It can be seen that the effect occurred in alloys that contain only sub-stitutional components as well as in alloys that contain carbon as an interstitial solute. The appearance of martensite formed in this manner is illustrated in Fig. 1, which represents a polished film of alloy No. 1 at XI0 magnification. The martensite plates can be recognized by their surface relief effects. In addition, heavily strained (owrinkledo) austenite can be seen near the edges of the film where it is thinnest and transformation stresses or strains can be accommodated by plastic deformation most easily. The nonuniform distribution of transformed regions is probably due to the varying thickness of the film. These observations were common to all materials listed in Table I. Because effects of supercooling or straining can

Jan 1, 1962

By E. Douglas, D. N. Collins, J. R. Stevens

E. Douglas (Dept. of Scientific and lndustrial Re-search, Warren Spring Laboratory, Hertfordshire, England) — The authors are to be congratulated on the considerable improvements they have made in tailoring efficiency and selectivity terms which are generally superior to the alternative forms in current use. However, I feel that their efficiency expression is limited to lower-grade feeds; its accuracy reduces as the feed grade increases. For example, its application to such processes as the beneficiation of glass sands, refractories and clays will invoIve considerable inaccuracies. The reason for this lies in the direct use of recovery, which, with high-grade feeds, biases their empirical expression, R(1 - c/h). With a 90% grade feed, the recovery weighting for the slightest degree of beneficiation, over a zero efficiency sampling operation, will be 90+%+ I disagree with their second basic requirement which states that there can be no fundamental basis for any single quantifying expression. A formula giving a comprehensive representation of concentra- tion efficiency can be derived fundamentally accord-to the procedure outlined in the literature. '' This formula, called the Basic Efficiency formula, is

Jan 1, 1963

By Irving Palmer

DURING the past 15 years in this country there have been few additions to the literature of lead smelting. After the consolidation of the principal smelting companies at the beginning of this period it became the policy of the larger company not to permit the publication of details in regard to many of its metallurgical processes. This led to similar action on the part of some of its competitors. The result, of course, was a decided decrease in the number of papers written upon the practical side of the subject. Even upon the theoretical side the contributions have been few. It would seem that the industry as a whole has suffered from this general unwillingness to exchange information. While it is true that a given company is entitled to the reward that may come from its own development of a new process, it is also true that a still greater reward might be the result of a free exchange of ideas with other plants. This principle has been recognized for a long time in other metallurgical industries, notably those engaged in the smelting of iron and the manufacture of steel. It is pleasing to note that the leading lead-smelting company has very recently decided to modify its policy of secrecy, and to permit the publication of papers covering some details of its metallurgical methods. The statement has been made that there has been but little progress in lead smelting during the period just referred to. This impression is due in part to the scarcity of papers written on the subject. There has been, it is true, some discussion of the new sintering processes, but with little reference to detail, and to the effect that blast roasting has had upon the industry as a whole. In spite of the prevailing belief, it may be said that lead smelting, in common with other metallurgical industries, has made steady and substantial progress. It is the purpose of the present paper to discuss briefly some features of the industry as it is now conducted, with special reference to the blast-furnace practice in the larger silver-lead smelting plants of the United States and Mexico.

Jan 7, 1914

By H. J. Modi, D. W. Fuerstenau

pH effectively regulates the flotation of corundum through its control of the surface charge. Since collector ions function as counter ions in the double layer, the collector must be anionic when corundum is positively charged and cationic when it is negatively charged. Even a long-chained xanthate will float positively charged corundum. Association of the hydrocarbon chains of the adsorbed collector ions gives rise to increased adsorption and increased rate of flotation. Because of this phenomenon, neutral organic molecules aid flotation although the unionized collector cannot promote flotation independently. Na2SO4 was found to depress the flotation of corundum with animic collectors through ionic competition whereas the same salt activates corundum for flotation with cationic collectors. A close connection between ion association, electrokinetic behavior, and floatability is suggested. As part of the increasing interest in the physical chemistry of flotation, strong experimental evidence has been obtained which indicates that organic ions are adsorbed as counter ions by non-metallic oxide minerals mainly because of the electrical forces which exist at interfaces(1-3). Thus flotation of such minerals without activation should then be appreciable only when the mineral and the collector are oppositely charged. Since only limited work has been reported on the effect of surface charge upon flotation behavior(3) this general hypothesis on the flotation of insoluble oxide minerals has not been tested thoroughly. Investigating the flotation of a mineral for which extensive electrokinetic data exist yields a way to test this hypothesis more extensively. The electrokinetic behavior of corundum in solutions containing both organic and inorganic electrolytes has been studied quite thoroughly' Electro-kinetic measurements have shown that in the case of corundum, simply by controlling pH the solid surface can be charged either positively or negatively. For this reason corundum was chosen for study. The object of this paper is to present a study of the flotation of corundum and to explain the results in the light of our knowledge of adsorption mechanisms gained from streaming potential investigations. This paper is concerned mainly with the effect of surface charge on flotation with anionic and cationic collectors, but in addition such flotation phenomena as collector hydrolysis, Van der Waals attraction between hydrocarbon chains, ionic competition, and activation are discussed. While the present paper is confined to a reporting of the data obtained and some of the more immediate conclusions, it will be seen that the results, in combination with those on other systems, do promise a

Jan 1, 1961

By Peter F. Weiss, H. Riedler, I. M. Moschitz, A. Olsacher, G. B. Fettweis

CONTENTS : 1. NATURAL FACTORS Geology Petrography and Rock Mechanics Mining System Orientation Rock Bolting System Movability of the Ore Grain Size Distribution Permeability Contamination Value of the Ore Hydrology 2. TECHNICAL FACTORS Height Length and Width Drawing Areas Time Factor Water Predrainage Surf ace Draining Underground Draining Advancing Slitting Sequence of Development Initiation of the Caving Process Drawing Rate 3. SPECIFIC MINING RULES Advancing Development Drawing Rate Interruption of Drawing (Water Distribution, Concentration of Mud, Dilution) Blasting 4. CONTROLS Safety Controls for Operation Computerised Drawing Control Structure of the Computer Program Hard Ware Print Outs 5. SUMMARY 6. ACKNOWLEDGEMENTS 7. REFERENCES Under the heading "Development System for Block Caving under Severe Conditions" a report was presented to this congress regarding a magnesite mine using block caving for several years. On account of the experience gathered in this mine and the results of far reaching exchange of experience, as well as under due consideration of the international literature it is tried to systematically list and briefly discuss the following factors that have to be considered for development and draw control of block caving. 1. NATURAL FACTORS It is self evident that this implies all those circumstances given by nature and which cannot be altered by man. Any mining activity is subjected to those and the success is depending on how far technology can be adjusted to those conditions. Geology Deposits of considerable thickness with rather steeply inclined flat-faced contacts are optimal for block caving. While vertically there is practically no limitation- for the deposit, theoretically, the smallest horizontal basis apt for operating block caving is the minimum area necessary to get the rock to completely cave in by undercutting and drawing. Practically, only consider- ably bigger main dimensions are found, mainly because of technical factors (machinery and equipment) and economic factors (cost ratio of exploration vs. development, danger of contamination).

Jan 1, 1981

By R. W. Bartlett

DISILICIDE coatings, MeSi2, on refractory metals are usually grown by a solid-state diffusion reaction similar to the parabolic oxidation of metals. Two or more silicide compounds occur in each of the binary silicon-refractory metal systems. When an adequate source of silicon is available during the coating process, the lower silicide compounds are usually not formed.1 However, during service application of the coated refractory metal, continued heating causes further diffusion and growth of the lower silicides. A study of the growth kinetics of the lower silicides in the molybdenum and tungsten binary systems with silicon was previously reported.2 The present study is concerned with the growth kinetics of Ta5Si3 and Cb5Si3, formed as conjugate layers between TaSi2/Ta and CbSi2/Cb diffusion couples, respectively. Diffusion couples consisting of disilicide-coated tantalum and columbium sheet coupons were subjected to diffusion heat treatments, cross-sectioned, and scanned by an electron-microprobe analyzer to determine the relative X-ray intensity profiles. These profiles correspond closely to concentration profiles for the constituents, and were used to identify phases and locate phase boundaries. The analysis of a single specimen after a diffusion-anneal provides only one value for the Me5Si3 phase thickness, corresponding to the time and temperature of the diffusion treatment. Consequently, each isothermal curve showing the rate of accumulation or depletion of silicide phases required several samples with identical diffusion temperatures but different diffusion times. The disilicide coatings were prepared by pyrolizing commercially pure silane in a hydrogen carrier gas. The hydrogen was purified by passage through a palladium membrane. Commercially pure tantalum and columbium sheet metal coupons, 0.005 by $ by 2 in., were used. All of the coated specimens for each system were prepared together in a single group in order to minimize coating variations among individual specimens. During pyrolysis, the brightness temperature was maintained at 1200°C. With suitable flow rates at this temperature, only the disilicides of tantalum and columbium were formed in detectable amounts. Coated specimens were subjected to diffusion an-neals in a tube furnace with automatic proportional control within ±10°C. A H2-Ar mixture, deoxidized and dried over anhydrous magnesium perchlorate, was used to prevent oxidation during the diffusion anneal. Diffusion couples were cross-sectioned, polished and examined with an A.R.L. electron-microprobe X-ray analyzer. Both metal constituents in each specimen were simultaneously scanned using a 1-p beam spot size and either 1- or 2-µ steps. Analyses were performed using the Ka radiation of columbium and silicon, and the La, radiation of tantalum. For all specimens, an acceleration voltage of 30 kv was used, and integration was made against the specimen current. LiF and A DP monochrometers were used to isolate characteristic radiations. Three or more traverses were made on each specimen. The intensity scales were adjusted using the constituent metals and standard samples of the silicide compounds which had been verified by X-ray diffraction. The relative intensity profiles were used directly, in conjunction with the standard samples, to identify compounds and phase boundaries. The stoichiometries differ considerably between the silicide compounds in both systems, and the homogeneity range for these silicide compounds is narrow. These characteristics result in marked differences in relative intensities of the fluorescing elements—differences which permit ready identification of phases and phase boundaries. Projections of both electron back-scattered images and characteristic

Jan 1, 1967

By D. G. Westlake

Levine has concluded that prismatic slip in titanium is controlled by two distinct thermally activated processes in the temperature ranges O° to 220°K and 220" to 300°K. We feel that his evidence is not convincing. He has drawn a curve through the plot of activation volume u* vs temperature T with a break at 22WK, Fig. 2. We believe that considering the possible experimental error apd the fact that there are only four points between 4° and 196°K, one could be justified to represent these points by the smooth curve we show as a solid line in Fig. 12. Levine believes that (8rf/aT)+ is discontinuous at 220°K, but he hints that he recognizes the possible doubt. We doubt seriously that the results shown in Fig. 1 indicate a discontinuity at 220°K. Certainly if he were justified in drawing a straight line through only four points on Fig. 2, we are even more justified in drawing straight lines through the seven points between 77" and 297°K on Figs. 1 and 3, because a straight line touches all seven of his circles. If his measurements of t were so precise that his decision to draw two curves in Fig. 3 is valid, then the experimental technique is deserving of further mention. We have drawn a smooth curve through the results in Fig. 3 and used this and the curve in Fig. 12 to obtain the values of shown in Fig. 13. Finding continuous is a contradiction of Fig. 4, which deserves comment itself. Levine obtained the solid circles in Fig. 4 using Fig. 2 and a smooth curve through the points shown in Fig. 3. We have replotted these solid circles in Fig. 14. We submit that there is no basis for his two straight lines (dashed in Fig. 14), and therefore have superimposed the curve that we believe is indicated. Certainly, there is reasonable doubt that a discontinuity in dH/dT exists at 220°K, even when one accepts Fig, 2. Furthermore, if one draws the straight lines indicated by least-squares treatments of the results presented as open circles in Fig. 4, their intersection is at about 196°K, not at 220°K as shown. Thus the alleged agreement between Figs. 3 and 4 with respect to "break" temperatures is not apparent. In Fig. 9, Levine has drawn a straight line very much different from the one indicated by a least-squares treatment. Obviously, he has done this because he recognized that H = 0 when T = 0. He is consistent in drawing the low-temperature curves in

Jan 1, 1968

By J. Richter, D. Schulze

J. Richter and D. Schulze (Deutschen Akademie der Wissenschafte zu Berlin)—Introduction. In a recent paper R. G. Garlick and H. B. Probst reported on experimental results of investigations of room-temperature slip in zone-melted tungsten single crystals.17 In the paper it was pointed out that slip lines could be detected with an optical microscope only after about 10 pet plastic strain of the crystal. In our investigations we could observe slip lines in tungsten single crystals of defined orientations already with an elongation of 0.02 to 0.03 pet.18"9 Experimental Technique and Results. The tungsten single crystals were produced from 4 to 5 mm sintered rods* as starting material by electron- beam zone melting. With single-zone-pass melting a speed of 0.5 mm per min was used, while three-pass melting could be handled at a speed of 3 mm per min. Crystal axis orientations were located in the shaded area of the stereographic triangle, see Fig. 6. Orientation 1 is located at about 18 deg and orientation 2 at about 5 deg on the great circle from [011] to [ill]. This corresponds approximately to the orientations P and M referred to by Garlick and Probst. Our single crystals had a length of about 70 mm and were profiled solely by electrolytic means, leaving grip ends at both ends of the crystals. Between the latter, a cylindrical crystal of 45 to 50 mm length and about 2.4 mm diam was obtained. The crystals were deformed at room temperature in a commercial tensile-testing machine to obtain a strain of 0.02 to 5 pet. The average strain rate e = eP/t for all tensile tests amounted to approximately 10 -6 to 10-5 per sec, with ep representing plastic strain and t the duration of applied stress. In Fig. 7 a crystal is shown elongated by 0.03 pet. The picture was obtained by means of an optical microscope. Figs. 8 and 9 give electron-microscopic pictures of slip lines of crystals elongated by 0.07 and 1.1 pet, respectively. For crystals with the orientation 1, see Fig. 6, only the two main slip systems (101)[111] and (110)[111] were found. With the crystals of group 2 the two main slip systems are again evident, with

Jan 1, 1965

By P. G. Hallof

Only recently has the term Induced Polarization found its way into geophysical literature. Schlumberger first mentioned the possible use of the induced polarization effect in one of his early papers. Later, induced polarization was the subject of several university theses, such as Seigel's at the University of Toronto and Bliel's at the Michigan School of Technology. In addition, a group at the New Mexico School of Mining and Technobgy has done work on induced polarization. There is very little to be found in print on the subject of induced polarization. Several papers have been presented at meetings, the 1958 AIME and SEG* conventions, for instance, on laboratory measurements of the effect and theoretical considerations useful in the interpretation of field results. This paper is the first attempt to present actual field results which show the usefulness of induced polarization as a prospecting technique. There are several phenomena that can cause polarization when electrical current is passed through the ground. In a paper presented at the 1958 SEG* meetings Professor T. R. Madden of M. I. T. demonstrated that only two of these gave rise to appreciable effects. The first is a result of the membrane and diffusion effects in a sandstone that contains appre- ciable amounts of clay minerals. The unbonded charges associated with the clay mineral forma material that passes positive and negative ions with different mobilities. When current is passed through such a system for some period of time, polarization results. The second phenomenon, which gives rise to very much larger polarization effects, is the one used in the new prospecting technique. These effects are a result of the blocking action or polarization of metallic or electronic conductors in a medium of ionic solution conduction. This electrochemical polarization, called "the over-voltage effect" by electro-chemists, occurs whenever electrical current is passed through a volume of rock which contains metallic minerals such as base metal sulphides. This polarization at metallic interfaces in ionic solutions depends upon the chemical energies necessary to allow the ions to continue the flow of current by giving up or receiving an electron from the metallic surfaces. The energy stored in this reaction isanalogous to that stored when a condenser is charged. If a d. c. current flowing through such a system is interrupted, the polarization can be detected as a small, decaying current that flows after the applied current is discontinued. The decaying potential measured is a result of the current flow caused by charges returning to their equilibrium positions from the positions they assumed under the applied potential field. Because of the polarization, there is an excess of change at each metallic interface. There is an alternate method of measurement of the induced polarization effect. The electrical

Jan 1, 1961

By C. Dinis da Gama

Because of the growing importance of back analysis for the interpretation of rock slope failures, particularly in open pit mines, it is suggested a methodologic sequence of activities for dealing with those problems. The principal mathematical tools for the interpretation of the most common mechanisms of slope failures are reviewed, including methods of stress and strain analysis, which seem to be more powerful for parametrization studies, and for developing more realistic explanations of slope behaviour, such as the measurement of displacements. An application of those methods is described, using slope failures detected in a Brazilian uranium mine (Cercado), thus providing reliable shearing strength parameters for the rock mass discontinuites, which were used in the final pit design. The concept of using backanalysis results to supply input data for pit design was implemented by means of the excavation of an experimental trench within mine limits, where specific instruments were installed, and several slope failures were monitored and backanalysed, in order to yield information about sliding mechanisms in the future open pit.

Jan 1, 1983

By Jack G. Gill, Richard A. Dick

Blasting safety is a subject that cannot be overemphasized. Two years ago, a study was published describing g a series of fatal blasting accidents which took the lives of ten metal and nonmetal miners during the period of May 1973 to August 1974.1 Each accident was described, and the direct causes were delineated. In each instance, specific MESA safety regulations were violated. Four of the victims were killed by drilling into explosives; two were killed by lingering too long in the vicinity of fuse rounds; two fatalities resulted from improper guarding of shots; one blaster did not retreat far enough to avoid the blast concussion; and another used an improper tester for checking an electric blasting cap. All of these fatalities could have been avoided by adhering to the MESA blasting regulations contained in 30 CFR Part 55 (Health and Safety Standards-Metal and Nonmetallic Open-Pit Mines), Part 56 (Health and Safety Standards-Sand, Gravel and Crushed Stone Operations), and Part 57 (Health and Safety Standards-Metal and Nonmetallic Underground Mines).

Jan 11, 1977

By G. R. St. Pierre, A. J. Wilhelem

In connection with the reduction of hematite or magnetite to metallic iron, it appeared desirable to study the rate of reduction of each oxide to the next lower oxide under conditions which excluded all other condensed phases. For this purpose, pellets of Fe,O,, Fe,O,, and oFeOo were prepared. A gas train for the preparation of Ar-Hz-H20 mixtures was employed to establish a continuous flow of a controlled atmosphere over a pellet suspended on a balance. In this manner the following individual reduction steps could be studied: For example, pellets of hematite were reduced solely to magnetite by adjusting the gas atmosphere such that it was oxidizing to wustite. In other words, the reaction was complete when the hematite pellet had been totally converted to magnetite. The pellets were prepared from Baker Chemical ferric oxide. The ferric oxide powder was moistened and handrolled. Air sintering at 950°C produced Fe,0, pellets with a density of 3.65 g per cm3. The pellets ranged in size from 0.6 to 1.2 cm diam. The magnetite and

Jan 1, 1962

By T. H. Oxnam

INTRODUCTION. THE predominating value of the ores now being treated by the Palmarejo and Mexican Gold Fields, Ltd., is silver, although some gold is also carried. The present method of treatment consists of wet-crushing and concentrating, followed by the cyanidation of the unroasted sands and slimes. The sands are treated by leaching and the so-called accumulated slimes by a system of agitation and decantation. It is only within very recent years that the cyanidation of unroasted silver-ores has been commercially successful. In fact, at the time operations were begun at the cyanide-plant at Chinipas, February, 1902, I knew of no other leaching-plant treating similar ores successfully. The cyanide treatment of the Palmarejo ores differs but little from the ordinary practice in cyaniding gold-ores; and perhaps but little, if any, new information concerning the metallurgy of silver is to be gleaned from it. PALMAREJO MINE. The Palmarejo mines are located in the southwestern part of the State of Chihuahua, Mexico, on the foothills of the Sierra Madre mountains, at an elevation of 3,200 feet. The mills, 12. miles distant, are situated on the Chinipas river, near the town of Chinipas, which is about 150 miles northeast of Agiabampo, on the Gulf of California. Supplies are shipped via this port as this route is the best and most direct to the property. The ore-bodies in the Palmarejo mines have been deposited. along a series of rock-fractures, caused by an intrusion of eruptive rock. The most important of these fractures or fissures, both in width and value, are the Prieta and Blanca veins, which.

Jul 1, 1905

By Walter E. Duncan

The ores treated at the concentrating plant of the Mahoning Mining Co. at Rosiclare, III., come largely from the blanket replacement deposits of the northeastern part of Hardin County, Illinois, and consist of complex mixtures of galena, sphalerite and fluorspar in a gangue of quartz, limestone and sandstone. The several minerals are so intimately inter-grown that they are not liberated at the sizes usually treated by gravity concentration in the usual fluorspar plant. For this reason, an all-flotation method of concentration was developed in cooperation with the station of the U. S. Bureau of Mines at Rolla, Mo.1 This flotation separation made possible the commercial production of four concentrates: (I) lead, (2) zinc, (3) acid-grade fluorspar and (4) metallurgical-grade fluorspar.2,3 Although fluorspar had been floated in Canada in 1921 and a plant at Rosiclare had been floating fluorspar since March 1929, fluorspar flotation was given considerable impetus by the Mahoning developments, since some features of the separation were quickly adopted by other fluorspar companies. The Bureau of Mines6 reports that in the 10 years preceding 1938 only 50,552 tons of fluorspar flotation concentrates were produced in the United States. The rise from this almost nominal figure to 153,750 tons (largely acid grade) in one year (1944)6 is indicative of the activity in fluorspar flotation occasioned by the war. The industry thus proved to be in a position to expand and keep up reasonably well with the requirements imposed upon it by such developments as occurred in high octane aviation gasoline alkylation, in the use of Freon as a refrigerant and as carrier in the Aerosol "bug bomb," and in the atomic bomb project as well as in the expansion of other activities requiring hydrofluoric acid; for example, the aluminum industry. Despite the fact that the greater portion of acid-grade fluorspar produced in the last few years went directly into war uses, the future of the acid-grade field still appears bright. As a result of the activity in fluorine chemistry during the war, it seems likely that in the relatively near future almost every phase of human endeavor will find some fluorine compound involved. The other three concentrates produced deserve some attention in these introductory remarks. The lead concentrates first produced contained both zinc and fluorspar but these did not interfere with their marketing. As will be pointed out later, the quality has steadily improved until today it is a relatively high-grade product. Although some zinc smelters accept concentrates containing limited quantities of fluorspar, it is a very objectionable impurity. Since flotation methods fail in the complete removal of the fluorspar, chemical methods were developed for

Jan 1, 1947