Search Documents

By J. P. Neumann, L. Raymond

At temperatures near 1000°C, only the (112) (111) slip systems are operatire in tungsten. Therefore, the substructure introduced into the billet upon rleforming a single crystal by rolling at 1000 "C can be controlled by proper selection 01. processing ral'iubles. Using a reduction of 10 pct pel- pass, the (001)[110] and the (110)[001] crystals will deform by duplex slip rip to a 50 pet reduction in thickuess. These rolled single-crystal sheels are characlerized by anisotropic hardening, retention of ductility with warm working, lattice bending which is related to the conlacl (angle, and macroscopic dimensional changecs in the length bid not the width of the billet. When several slip systems become operative, a greater degree of work hardening is itztvoducetl into the crystal. This rolling- condition is characlerized by isotropic hardening, loss of ductilily with warm working, complex lattice distortions, and macro-scopic dimensional changes in both the length rind Width of the billel. IN tungsten, the {1 10}(111) slip systems are operative below room temperature,' while above 700°C only the {112{ (111) slip systems are observed.2,3 In the transition region, i.e., room temperature. both systems appear. It is the purpose of this investigation to show that tungsten single crystals deformed by rolling at a temperature where only one slip system is operative generate dislocation substructure which depends on the crystal orientation. For a specific crystal orientation. the resulting dislocation substructure can be further influenced by modifying the rolling procedure. Crystals oriented for multiple slip display less substructural sensi- tivity to modifications in processing techniques than do single crystals oriented for duplex slip. Under simple slip modes of deformation, very little work hardening is introduced into a rolled single-crystal sheet. Mechanical properties such as room-temperature strength. ductility, and hardness are used to confirm the existence of the different work-hardened conditions generated within the crystal by modified warm-rolling techniques. EXPERIMENTAL PROCEDURE Material. Single-crystal billets of four different crystal orientations. grown by the Arc-Verneuil technique. were ground to a size of 0.25 by 0.375 by 3 in. In terms of their rolling plane and rolling direction, the billets had the following orientations: (1101 [001 ] (110) [110] (001) [110] (001) [100] The actual orientation of all crystals was within 5 deg of the ideal orientations. The typical impurity content of the crystals is given in Table I. Polishing and Etching. Polishing was done elec-trolytically in a 20 g per liter aqueous solution of NaOH at approximately 10 v. It was established by the Laue back-reflection X-ray technique that the surface damage due to grinding and cutting operations with a diamond wheel did not exceed 0.001 in. Therefore after each cutting or grinding operation at least 0.002 in. was removed electrolytically from the surface in order to eliminate surface effects. By lowering the voltage to 3 v, subgrain boundaries and individual dislocations are identified in agreement with Berlec 4 where the etch-pit traces on a cubic plane form a square. The etching time was about 5 sec at room temperature. Rolling. Rolling was carried out on a Loma 2-high mill (Model 600). The peripheral velocity of the 6-in.-diameter rolls was 500 in. per min, with the surface temperature of the rolls about 400° to 450° C The billets were heated before each pass for 30 min in argon to 1000 C. Oxidation of the crystals during rolling in air resulted in a thin layer of greenish-yellow WO 3 This oxide was removed after each pass by immersing the crystals for a few minutes in a boiling NaOH solution. Prior to the initial rolling pass, a surface layer of 0.001 in. was removed by polishing. The crystals were then annealed in vacuum (10-4 torr) at 2400 C for 30 min. All crystals were rolled in the same direction; i.e., the same end was always introduced into the rolls. The rolling program was conducted in

Jan 1, 1965

By Paul H. Lu

Methods and results of measuring three basic parameters for ground stability control, ground pressure, strata movement, and geomechanical properties of mine rock are presented in this paper. It is found that these parameters can be measured in situ by simple and practical techniques with nonsophisticated and inexpensive instruments. Specifically, a drillhole dilation technique employing a cylindrical hydraulic borehole pressure cell (CPC) was used to determine the modulus of rigidity. Premining ground pressures were determined by pressure convergence tests with a combination of one CPC and two pre-encapsulated flat hydraulic borehole pressure cells (BPC) installed in a single drillhole. Abutment pressures and pillar loading were monitored with BPC's. Differential strata movements and bed separations were measured with self-recording 10-anchor-point extensometers. Roof-to-floor convergence was measured with self-recording convergence meters. Some applications of these in-situ-determined parameters to mine design and ground stability control are also discussed.

Jan 1, 1984

By Zdzislaw Specht

THIS paper discusses elementary laws pertaining to seismic reflection methods and presents a general and simple criterion for determining the direction of dipping of a reflection horizon from observational data of distance and time. The important development of practical geophysics and the successful results obtained in America, Germany, and other countries, caused introduction of geophysical methods of prospecting in Poland. Of all methods, seismic prospecting has proved most successful in the area of the Carpathian foreland, where new oil reserves are to be expected. Because of the great depth of the sedimentary column in that area, rang-ing sometimes over 2000 meters, it was obvious that only the seismic reflection method could give reliable information regarding the structural features of these strata at such a depth. During the experimental surveys it appeared that the complicated geological conditions of that area do not always allow prediction of the depth and the angle of dipping of reflecting horizons, and for that reason information about the inclination of a given horizon has great importance in the determination of subsurface structure. Therefore the problem arises of obtaining from seismic reflection data reliable information as to the direction of dipping of reflecting strata, without any previous knowledge of the average velocity and depth of geologic horizons under consideration.

Jan 1, 1940

By V. H. Whihelm

Since 1935 California has enjoyed a remarkable cycle of discovery, which has placed the state in a very satisfactory position in regard to oil reserves. Most ol the geophysical plays have been drilled and it is possible that new discoveries must be made by the application of careful geologic and stratigraphic studies. During 1940 only one new field was discovered, which, although not of major importance, may lead to additional discoveries. During the year, 113 wildcats were drilled. New discoveries, extensions and a reappraisal of discoveries made in 1939 will not approximate over 50,000,000 bbl., as against an estimated withdrawal during the year of 224,000,000 barrels. Demand in terms of crude for 1940 was 632,000 bbl. per day as against 626,000 bbl. per day for 1939. Demand for gasoline was the same as in 1939, but the demand lor fuel oil increased 3.8 per cent. Compared with 1939, Japanese shipments decreased from 75,786 bbl, per day to 61,000 bbl. per day, but the balance of Pacific foreign shipments increased from 59,409 bbl. per day to 61,304. Total with-drawals from storage during the year will approximate 7,000,000 bbl., almost all of which is fuel oil. Drilling activity was slightly greater than in 1939 and accounted for 890 new producing wells as against 851 for 1939 (Table 3). Production averaged 611,900 bbl. per day as compared with 614.,842 bbl. per day for 1939. The productive acreage figure of the state was increased by 4000 through discoveries and extensions. New Discoveries Los Angeles Basin District Del Vdle Field.—Northwest of Newhall, where the first oil well in California was drilled, R. E. Havenstrite completed his Lincoln No. I well, flowing 390 bbl. of 50" gravity oil together with 7000 M CU. ft. of gas. Later the well was recompleted, after cutting off the gas, for 950 bbl. of 34" gravity oil. The type of structure from which this production is coming is a plunging anticline, complicated by faulting. The Lincoln No. I well uncovered approximately 180 ft. of net sand. This field contains a gas cap and its indicated productive area approximates 500 acres. An intensive wildcat drilling campaign is expected during this coming year in the district in the vicinity of the Del Valle field. Extensions and Deeper Sand Developments Los Ange1es Basin District Athens Field.—On the northwest plunge of the Athens structure, the Thorley Oil Co. completed its No. 12-1 well, flowing 250 bbl. of 3 2" gravity oil from a depth of 8097 ft. The area in which the well is located is complicated by faulting and it is impossible at this date to determine the importance of this deep-zone discovery.

Jan 1, 1941

By V. H. Whihelm

Since 1935 California has enjoyed a remarkable cycle of discovery, which has placed the state in a very satisfactory position in regard to oil reserves. Most ol the geophysical plays have been drilled and it is possible that new discoveries must be made by the application of careful geologic and stratigraphic studies. During 1940 only one new field was discovered, which, although not of major importance, may lead to additional discoveries. During the year, 113 wildcats were drilled. New discoveries, extensions and a reappraisal of discoveries made in 1939 will not approximate over 50,000,000 bbl., as against an estimated withdrawal during the year of 224,000,000 barrels. Demand in terms of crude for 1940 was 632,000 bbl. per day as against 626,000 bbl. per day for 1939. Demand for gasoline was the same as in 1939, but the demand lor fuel oil increased 3.8 per cent. Compared with 1939, Japanese shipments decreased from 75,786 bbl, per day to 61,000 bbl. per day, but the balance of Pacific foreign shipments increased from 59,409 bbl. per day to 61,304. Total with-drawals from storage during the year will approximate 7,000,000 bbl., almost all of which is fuel oil. Drilling activity was slightly greater than in 1939 and accounted for 890 new producing wells as against 851 for 1939 (Table 3). Production averaged 611,900 bbl. per day as compared with 614.,842 bbl. per day for 1939. The productive acreage figure of the state was increased by 4000 through discoveries and extensions. New Discoveries Los Angeles Basin District Del Vdle Field.—Northwest of Newhall, where the first oil well in California was drilled, R. E. Havenstrite completed his Lincoln No. I well, flowing 390 bbl. of 50" gravity oil together with 7000 M CU. ft. of gas. Later the well was recompleted, after cutting off the gas, for 950 bbl. of 34" gravity oil. The type of structure from which this production is coming is a plunging anticline, complicated by faulting. The Lincoln No. I well uncovered approximately 180 ft. of net sand. This field contains a gas cap and its indicated productive area approximates 500 acres. An intensive wildcat drilling campaign is expected during this coming year in the district in the vicinity of the Del Valle field. Extensions and Deeper Sand Developments Los Ange1es Basin District Athens Field.—On the northwest plunge of the Athens structure, the Thorley Oil Co. completed its No. 12-1 well, flowing 250 bbl. of 3 2" gravity oil from a depth of 8097 ft. The area in which the well is located is complicated by faulting and it is impossible at this date to determine the importance of this deep-zone discovery.

Jan 1, 1941

By R. E. Ray, J. W. Stevenson, J. A. Berry

Conventional concrete block plastered with a cementitious coating is the most common material used in the construction of permanent stoppings to direct airflow in underground mines in the US. All mines experience various degrees of strata convergence depending on depth of overburden, geological conditions, and type of roof support employed. Strata convergence will cause cracks and joint openings in masonry stoppings, resulting insignificant air leakage losses. Where strata convergence is severe, complete structural failure of the stopping can ultimately occur. Reconstruction of damaged or destroyed stoppings adds expensive overhead to mining operations, and even greater expenses are incurred from the additional fan horsepower required to overcome leakage losses. Ideally, a stopping should maintain high resistance to airflow while yielding to strata convergence. By properly incorporating a polyisocyanurate rigid foam material within the masonry block structure, stopping service life can be increased in mines experiencing strata convergence problems such as floor heave, roof loading, and lateral rib movement.

Jan 1, 1986

By L. Obert, D. E. Stephenson

The objectives of this investigation were to develop a laboratory procedure in which core discing could be produced under known (and variable) stress conditions, and to study the discing characteristics of several fypes of rock. Discing of rock cores refers to the formation of discs or wafers of relatively uniform thickness which fracture or rupture on surfaces approximately *Fracture is a type of failure in which there is a complete loss of cohesion and fresh surfaces are created. Rupture is a type of failure in which there Is only a partial loss of cohesion. normal to the axis to the core (see Fig. 1). Usually the surfaces of the discs are concave-convex with the concave side toward the collar of the hole. The surface of the fractured discs are like those created by a tension failure (or possibly a shear failure with virtually no normal compressive stress). This phenomenon has been observed by a number of investigators1-5 in the course of diamond drilling in underground mines, especially in areas suspected of being under high stress. The state of stress in the core required to produce discing is not exactly known. Tranter and craggs6 theoretically investigated the stress distribution in an infinite cylinder, subjected to hydrostatic pressure, minus p, from z = 0 to z = 8 and unloaded from z = 0 to z = 8, Fig. 2. The exact solution to this problem shows that a tensile stress develops in the loaded region near z = 0 with the greatest tensile stress on the axis of the cylinder. A tensile stress also developed on the surface of the cylinder at a point just outside of the loaded zone. Jaeger and Cook3 experimentally investigated the discing mechanism by biaxially loading cores in a pressure jacket sealed at the ends by O-rings. According to the Tranter and Craggs theory it would be expected that failure should occur at the pressure discontinuity at the O-rings. The experimental results showed that if the specimen was unjacketed it broke at random points within the pressurized zone and at a pressure somewhat greater than the tensile strength of the specimen, presumably due to the development of a

Jan 1, 1965

By A. W. Asman

The problem of balanced design in a belt conveyor has been under constant study. Increased use of this method of transport in recent years has stimulated investigations. Conveyor belt, power transmission and other machinery should be adequate to perform the required service. All components of the belt conveyor should work as an efficient unit moving its load continuously between terminals. As part of a long term research project on belt conveyors, Hewitt-Robins established in 1954 a 2-year grant at Pennsylvania State University. Under terms of the grant, certain fundamental phenomena were to be studied. This work evolved a new concept in belt conveyor power determination based on the principle of belt tension. The Penn State contract furnished the foundation for later more detailed studies. From these most recent investigations, more specific factors were defined. In the final analysis, all of the data collected has been worthwhile in belt conveyor design. Units now operate over long distances at speeds of over 800 fpm. Long high lifts are commonplace. Where vertical or inclined shafts were the rule, belt conveyors receive first consideration. Although belt conveyors have moved forward rapidly, the future will see a tremendous gain in their use. The ideal test belt conveyor would be several thousand feet in length and have a maximum tension of at least 70,000 lb., Also, this conveyor should be horizontai and have a variable feed rate of more than one material. Data from such a field belt conveyor combined with laboratory information would permit accurate analysis. Since this type of conveyor was not available, many field locations were visited: An alternate would have been to erect a closed circuit system in the laboratory. Either method had limitations and the first was selected as having the best possibilities. Manufacturers of conveyor belting and machinery basically have been using the same horsepower formula. As more information became available from field installations, factors in the basic formula were modified. Practically all conveyors are designed today by adding together the horsepowers required to move the empty belt, move the load horizontally, and elevate the load. In selecting size of drive motor, the first two elements are relatively unimportant if the last is large. However, it is the combination of

Jan 1, 1961

By Austin E. Dwight

IT has been shown by Oelsen and Wever' that the effect of a solute element on the allotropic transformation in iron is dependent upon the quantity

Jan 1, 1957

By W. H. Bassett

In considering the effects of reducing gases on hot solid copper the following conclusions have been reached. (1) Depth of deoxidation of copper heated in reducing gas is greater the smaller the amount of cuprous oxide originally present in the copper, the range studied being from 0.015 to 0.136 per cent. oxygen. It is suggested that the reason for this difference in depth of deoxidation is that, when the copper is low in cuprous oxide, the reducing gas is diluted less by the gas that is formed in the reaction than when the copper is high in cuprous oxide; and the greater the concentration of the reducing gas the deeper the deoxidation. (2) The rate of deoxidation is much mire rapid at the beginning of exposure than at the end, a condition especially noticeable at temperatures around 900° C.; that is, deoxidation is retarded as the depth penetrated by the reducing gas increases. (3) Within the accuracy of the experiments arsenic in copper up to 0.5 per cent. has no tendency to increase or decrease the action of a reducing gas on the cuprous oxide present in the copper. IN 1912 pieces of 0.365-in. hard copper rod 1/2 in. long were heated in a porcelain tube in an electric furnace, while illuminating gas was passed through. An approximate analysis of this gas is: FIG. 1.-EFFECT OF TIME AND TEMPERATURE ON DEOXIDATION RATE OF 0.365-IN. COPPER BY ILLUMINATING GAS; COPPER PLUS SILVER, 99.983 PER CENT. Hydrogen 38 per cent., carbon monoxide 30 per cent., illuminants 13 per cent., methane 10 per cent., ethane 3 per cent., carbon dioxide 3 per cent., nitrogen 2 per cent., oxygen 0.4 per cent. After heating for various lengths of time at various temperatures, samples were quenched

Jan 1, 1926

A record $18.7 billion worth of metals, non- metals and fuels was produced in the U.S. during 1962, according to a year-end estimate from the USBM. The 1962 total value, based on preliminary statistics compiled by the Bureau, was nearly $600 million more than in 1961. Most minerals gained both in value and volume of production during 1962 according to information collected by the Bureau. All mineral fuels except anthracite showed increases. Among nonmetallic minerals- other than fuels-gains exceeded losses by two to one. Metal production held steady as gains and losses balanced.

Jan 2, 1963

By Joseph Moses Botbol

In passing the judgments essential to his trade, the geologist may be assisted by two new methods. These will enable him to (1) arrange the minerals of a selected group of base metal mining districts in the order of their typicalities and (2) compute the degree of mineralogic association between the model so derived and a district external to the model. It must be remembered, of course, that the methods discussed in this article are no more powerful than the structure of the model used and the data available. The geologist who employs these techniques must still exercise his expertise

Jan 1, 1970

By A. S. Odeh

During the last few years, several authors1-6 have advanced mathematical solutions, both exact and approximate, to the pressure behavior of a well producing from a region bounded by a circular discontinuity. The most recent solutions were reported by Carter, and by Bixel and van Poollen. Varter solved the appropriate equations analytically. Bixel and van Poollen reported a numerical solution and provided correlation charts for the interpretation of flow tests; their method uses an overlay technique and is valid for wide ranges of mobility and storage capacity ratios. The mobility ratio is defined as the ratio between k/p of the two zones, and the capacity ratio is defined as the ratio between $c of the two zones. We have developed independently an analytic solution, programmed for the CDC 1604, that agreed with Carter's.'1 The same differential equation, assumptions, boundary, and initial conditions were used. We ran 30 drawdowns and 30 buildups of a unit capacity ratio and of varied mobility ratios. We also varied the radial distances to the discontinuity, and the radii of drainage. We examined the results and obtained correlations that were simple to apply and useful in flow test interpretation. The results and the correlations reported here in graphical form allow the determination of the mobility of the two zones and the radial distance to the discontinuity. They eliminate the need to fit field data to a curve as is required in the overlay technique.6 Thus, the advantages of the present correlations are that they require less effort and they provide a unique answer. They also provide guidelines for selecting the parts of the flow test plot to be used in the interpretations. Moreover, the results obtained from the programmed analytic solution define the time intervals where the approximate solution reported by Hurstl and discussed by Larkin2 are applicable. Normal buildup and drawdown plots resulted in an early straight line, a long transition zone and a late (second) straight line. However, the second straight line will not occur if the drainage radius is not at least 10 times the radial distance to the discontinuity. The mobility of the imer and outer zones can be calculated from the slopes of the first and second straight lines, respectively, by the normal methods of the flow test analysis. We found that the radial distance to the discontinuity may be determined from the abscissa value for the point of intersection of the extensions of the two straight lines. Results similar to some of these were reported by Adams et aL7 The approximate solution compared favorably with the exact one during the first and second straight-line periods. However, during the transition zone, deviation occurred between the two solutions. Discussion of Figures Figs. 1 through 7 summarize the results of this investigation. On Figs. 3 through 7 there appears the equation of each respective plot. In this paper the mobility ratio M is defined as klp2/kzpl, where subscripts 1 and 2 refer respectively to the inner and outer zones, and dimensionless time = t, = 6.32 X In the investigation, M ranged from 0.25 to 50;

Jan 1, 1970

By J. B. Clark

In 1933, R. paris1 published a phase diagram for the entire Mg-Ca-Zn system. He reported the existence of a ternary intermetallic phase, Mg5Zn5Ca2, which formed a quasi-binary with the magnesium solid solution. Since then, no extensive work has been reported on the system. Recently however, indications of the existence of a second ternary in-termetallic phase in equilibrium with the magnesium solid solution led to a reinvestigation of the solid phase equilibria involving the magnesium solid solution. The 335°C (635°F) isothermal section was chosen for study. Metallography and powder X-ray diffraction were selected as the best mutually corroborating methods for determining the solid phase constitution. Seventy-six alloys were prepared from singly sublimed (99.95 pct) magnesium, electrolytic (99.95 pct) zinc and USP calcium. The analyses of some of the alloys are shown in Fig. 1. The alloys were melted in a graphite crucible under a chloride flu and chill cast in a split graphite mold. Dif-fusion couples (see Fig. 2) were prepared by casting molten Mg-20 wt pct Zn alloy around a cylinder of Mg-30 wt pct Ca alloy. The alloy samples and the diffusion couples were sealed under argon in Pyrex vials and annealed in a furnace capable of controlling within 1/2°C of 335°C. At the conclusion of the anneal, the alloy samples were quenched in ice water and the diffusion couples were air cooled. Procedures standard for magnesium alloys were used for metallographic examination. Powder X-ray diffraction patterns were taken on a G. E. camera with a 14.32 cm dim using nickel-filtered copper radiation. The redetermined 335°C (635°) section of the Mg-Ca-Zn phase diagram is shown in Fig. 1. TWO ternary intermetallic phases, designated w and

Jan 1, 1962

By Ingvar Janelid

DURING the last ten years, in the effort to save manpower and costs, methods of drilling and blasting in Sweden have changed and developed in a revolutionary manner. These developments have been accompanied by extensive alterations in methods of tunneling and in mining technique. Since the end of the 1940's there has been a 100 pct change-over in Sweden to the use of tungsten carbide tipped drill steel. Both investigations and practical results have shown clearly that a tungsten carbide chisel bit fastened directly on the drill steel is the most economical for Swedish conditions. This applies to drill steel up to the longest size it is practical to handle. In terms of drilling footage, durability of the drill steel and the tungsten carbide bit is generally the same. In this respect, therefore, a detachable bit offers no advantage over integral steel. Transportation of integral steel to the grinding plant, instead of detachable bits only, involves heavier work, but this is counteracted by placing grinding plants closer together or by grinding at the working place itself. The drilling rate with integral steel is higher, the trouble of changing bits is avoided, and the difficulties which always arise with joints are eliminated. At present steel dimensions are usually 7/8 in. with a shank 41/4 in. long, whereas the international standard shank was formerly 31/4 in. The longer shank renders possible a better guide control of the steel and consequently longer life for the rotation chuck and the water-flushing pipe. After extensive experiments and investigations, agreement has been reached in Sweden on certain series of standards, shown in Table I. Other steel dimensions are, of course, available for special purposes. The standard drill-steel set begins with a 34-mm diam and has a length interval of 2 2/3 ft. On the other hand, for ordinary drifting it has been proved more economical to use greater length intervals on the steel, so only one steel change is required for a 61/2-ft round. Moreover, owing to the relatively close hole spacing necessary in a drift round, it has been possible to reduce the diameters of the tungsten carbide bits. This results in faster and cheaper drilling. As shown by the table, the lengths of drill steels for normal drifting are 33/4 ft and 71/2 ft, with 29 and 28-mm diam bits. During the last few years operators have begun to use 3/4-in. drill steel in place of the 7/8-in. drill steel chiefly employed earlier. This is a valuable development in drilling technique, particularly in view of

Jan 1, 1955

By W. V. Long, D. H. Reynolds, R. B. Bhappu

Equilibrium distribution coefficients were determined for some monovalent and polyvalent ions for several absorbing and exchanging media as functions of pH and initial ion concentration. Among ions studied were NH4 (I), K(I), Ni(II), Ce(III), Th(IV), and Mo(VI). Absorbents used were: ion exchange resins; a tertiary, and a quaternary amine in an inert solvent; and some activated carbons. The ions studied were in aqueous HCI, HNO3, H2SO4, or HC104 solutions. The classical mass action expression proved of little value in describing the variations observed. The data indicate that the determining factors in absorption and ion exchange may be the ionic species in the aqueous solution, which in turn depend upon pH, dilution, and perhaps other conditions. Three sorption processes have become prominent in recovering values from leach solutions. These are: 1) ion exchange, 2) solvent extraction (liquid ion exchange), and 3) physical adsorption by materials of high specific surface. In the first two of these processes the exchange reaction is considered chemical in nature, and is discussed in terms of the mass action principle. The third is considered a surface phenomenon and is discussed in terms of surface areas and various forms (Gouy, Stern, Grahame, etc.) of the Helmholtz double-layer theory. Generally speaking, we have found in chemical analysis and hydrometallurgical studies that there are close similarities between the three sorption processes, and also differences which are difficult to reconcile with any of the usual theoretical treatments. That others have experienced the same troubles is shown by the fact that usable processes, in chemical analysis as well as in hydrometallurgy, generally are discovered by empirical procedures. EXPERIMENTAL CONSlDERATlONS The gaps between theory and practice have allowed many conflicting statements to appear in the litera- ture. To learn, in particular, the behavior of some metallic ions on a cation exchange resin at a constant pH, equilibration studies were made over a wide range of concentrations.' Results are shown in Fig. 1 for four metals in hydrochloric acid solution on a strongly acidic cation exchange resin, AG 50W-X8 (Bio-Rad). The distribution coefficient, defined as D = amount of metal extracted per g of resin/amount of metal unextracted per ml of solution is seen to vary in a way to support all manner of reports about its behavior with changes in solution concentration. The metals used were chosen from those least likely to form stable chloro-complexes. The changes of slope in the various isotherms may reflect formation of unsuspected chloro-complexes of low stability (ion-pairing for example) whose concen-

Jan 1, 1967

By W. A. Hockings, D. W. Fuerstenau, A. L. Mular

This paper briefly describes a simple air pycno-meter and its use for rapid determination of the composition of mixtures of solid particles. Research on such problems as the pelletizing of solids, the mixing of solid particles, and the comminution of mixtures can be simplified by means of this analytical tool. THEORY OF OPERATION Liquid pycnometers1 are commonly employed to measure volumes. These devices are time consuming and sometimes give inconsistent results. The liquid used in the pycnometer may have an undesired influence on the material to be measured; moreover, complete displacement of air by the liquid is seldom

Jan 1, 1963

By Charles W. Merrill

Obsolescence in the mineral world is virtually nonexistent if the term is taken to mean that a mineral commodity, once established in commerce and industry, subsequently has fallen into disuse. We are living in an age of minerals. Each generation puts an increasing array of mineral-based commodities, in larger quantities, to more uses than ever before. Bastnasite, a museum mineral and a collector's item a few years ago, is now produced in quantity at Mountain Pass, Calif. Uranium, a minor byproduct of vanadium mining in the Rocky Mountain plateau area before World War 11, has grown to be a leading mineral product in several western States. And finally the total quantity and value of minerals both in the United States and in the World establish new records almost yearly. Surely the mineral industry as a whole is not obsolescent in our economy. Nevertheless, there are particular uses for particular minerals that are obsolescent and some applications have been supplanted entirely. Tin does not occupy the prominent place in foil manufacture that it once did, and the schoolboy's slate left most classrooms before the oldest of us were born.

Jan 9, 1964

By D. J. Coolidge, H. L. Sheakley

THIS paper does not deal with all sands used in the glass industry in Missouri; it covers only that used in the plate-glass factory at Crystal City. However, it is probably safe to say that other sands, produced throughout the state for this purpose, are of identical nature. The glass sand used in Missouri is commonly called the St. Peter deposit, which is ascribed to the Ordovician Rock series in the form of sandstone. This St. Peter deposit, aside from a few small outliers, covers a large area of eastern Missouri. It forms, through a broad curve, the northeast margin of the typical Ozark region between Cape Girardeau on the southeast and Mineola, Montgomery County, on the northwest. The belt is extremely irregular, varying from one to ten miles in width; its length is 150 miles in a straight line. The outcrop near the entrance to the Crystal City mine appears in the form of a sandstone bluff approximately 30 ft. high, running along Plattin Creek (Fig. 1). Above the sand rock an overburden of Joachim limestone appears, which thickens to nearly 300 ft. and forms the hill commonly called Buck Knob. Test holes where drilled at various points and the drillers' log indicate that the St. Peter deposit ranges in thickness from 63 to 71 feet. PROPERTIES OF THE ST. PETER SAND From an analysis of the glass sands of the St. Peter formation in Missouri, the follow-

Jan 1, 1942

By P. O. Metz, E. L. Wiehe, J. S. Foster

BASED on their analyses of growth kinetics, ibbs' and Harris et al.' have recently proposed that the rate of subcritical graphitization of steel is controlled by the rate of diffusion of carbon in ferrite. illert has concluded that this is the rate controlling growth mechanism when the growing graphite particles are relatively large. Harris et al.' also propose that the matrix surrounding a growing graphite particle is plastically deformed to make room for the growing particle. If this plastic deformation does occur, then preferred recrystallization may be observed around the larger particles. If diffusion of carbon in ferrite is rate controlling, then a graphite particle growing in a matrix of, say, tempered martensite or pearlite, should be surrounded by a carbide depleted zone. Thus, the simple metallographic experiments reported here are sufficient to determine whether or not diffusion of carbon in ferrite is the dominant mechanism for the growth of graphite in steel. The present investigation considers graphitization in five alloys. The compositions are given in Table I. Graphitization was carried out at three temperatures: 900°K (627"C), 950°K (677"C), and 990°K ('717°C). Samples were reacted in both the martensitic and the pearlitic initial conditions. In the hypoeutectoid steels, Sets 7 and 8, .and in the hypereutectoid Fe-C binary, Set 6, graphitization was very limited after 1000 hr at temperature. In these samples graphite particles observed were less than 10 p in diam. In the hypereutectoid commercial steels, Sets 1 and 3, large graphite particles (100 p) did not appear until after 250 hr at temperature. The limited number of graphite particles observed and the range of sizes obtained prohibited measurement of growth rates in this investigation. However, in all samples showing graphitization, neithe a carbide depleted zone nor recrystallization was observed. illert's model predicts that diffusion of carbon in ferrite should become dominant for graphite particles larger than about 300 p in diam. The largest graphite particle observed in this investigation was approximately 450 p in diam. No evidence of carbide depletion was noted. Fig. 1 shows a typical graphite particle. This nodule is from an initially pearlitic sample from Set 3 after

Jan 1, 1970