Search Documents

By S. Ramachandran, N. J. Grant, T. B. King

MANY investigations of the rate of the sulfur transfer reaction between carbon-saturated iron and blast furnace type slags have been made." It is evident that the reaction is complex, the rate being affected by the presence of elements dissolved in the metal that are readily oxidized and therefore capable of existing in the slag phase. Thus Goldman, Derge, and Philbrook- have shown that carbon, silicon, manganese, and aluminum, in order of increasing effectiveness, accelerate sulfur transfer from iron containing these elements to blast furnace type slags. Quantitative information is still, however, not available on the relation between what have been termed side reactions, such as silicon transfer and CO evolution, and the sulfur transfer reaction itself. In other words, the stoichiometry of the reaction has not been investigated. In the present investigation, the transfer of all reacting elements and the evolution of CO have been measured simultaneously in order to establish the mechanism of the reaction which occurs in practice. Information of this nature cannot be deduced from equilibrium studies. It should be pointed out that in kinetic studies of this type quantitative conclusions are applicable only to the system studied. This restriction should be borne in mind when attempts are made to compare results from different investigations. Apparatus The apparatus used enables slag and metal samples to be taken at frequent intervals and also provides a continuous record of the amount of gas evolved. A sketch of the apparatus is given in Fig. 1. It may be considered in three sections: 1) furnace section, 2) blank volume section, and 3) pressure measuring section. The furnace section is shown in detail in Fig. 2. It consists of two graphite crucibles, C and D, super-

Jan 1, 1957

By Samuel Hoyt

SOME of the more important properties of finished materials are strength, ductility, toughness, resistance to alternating and repeated stresses, etc: Of these, the property that appears to have received the least consideration, at least in this country, is toughness, which is clue, possibly, to our regarding toughness as a qualitative property or, at any rate, as one that, parallels ductility. This arises out of our greater experience with the simple carbon steels in the rolled or forged (non-heat-treated) condition which, qualitatively, are tough if ductile and are not tough if brittle. In this way we have erroneously become, accustomed to judging the toughness of a material from its behavior in the tensile or similar test. The point of view presented in the present paper is that toughness, like hardness or tensile strength, should be regarded as an independent property and of sufficient importance to require, in so far as that may be possible, quantitative determinations. If such be true, it becomes at once necessary to devise experimental means for measuring, or valuating toughness, and the notched-bar impact test (the Charpy test) is advanced as the most logical test that has so far been developed for this purpose. It is further advanced, with particular emphasis, that we have two kinds of toughness to deal with and, accordingly, they will be dealt with independently. CLASSIFICATION OF MATERIALS ACCORDING TO TOUGHNESS Toughness has been defined somewhat as follows: Tough materials are those that offer considerable resistance to permanent deformation but which, once such resistance has been overcome, may' be deformed plastically, but only by the expenditure of considerable energy. In other words; tough materials may be deformed plastically but they absorb a considerable amount of work in the process. This kind of toughness may be called "static" toughness when the rate of loading is reasonably slow or "dynamic" toughness when the rate of loading is

Jan 2, 1919

By J. L. Gregg, J. L.

RECENTLY there has been considerable interest in the production and use of extra hard alloys composed primarily of tungsten and carbon. Dr. Hoyt's recent paper1 gives a good description of these alloys and describes their performance when used as tools. There are a number of these alloys on the market sold under various trade names, and it is the purpose of this paper to describe the results of an investigation of the structure of five of these alloys by means of microscopic and X-ray methods. The samples studied were in the form of small tools or wire-drawing dies, which were either purchased or supplied as samples. They were in some cases not supplied by the original makers but were furnished by the agents in this country, and we wish to call attention to the fact that they may not be truly representative of the materials supplied under the various trade names. No performance data are given and no inference as to the inferiority of one alloy as against any other is made. K. Schröter2 recently described methods for polishing alloys of this type for microscopic examination and has presented photomicrographs of several alloys. However, he did not identify their constituents or describe methods for their identification.

Jan 1, 1929

By Fulton Flick

THE micrography and macrography of aluminum and its alloys present certain difficulties. Many of the difficulties attendant on the micrography have been removed by methods developed during the past few years, notably those of E. H. Dix, Jr.1 The development of grain size in aluminum and its alloys may be equally troublesome, yet comparatively little detailed attention appears to have been given to it. Satisfactory reagents. are available for the development of such structures in ferrous and most non-ferrous metals, but those applied to aluminum and its alloys, i. e., alcoholic or aqueous solutions of sodium hydroxide or hydrofluoric acid are not entirely satisfactory. Hanson and Archbutt,2 in speaking of these two reagents, state that "These two reagents give fairly satisfactory results, but they sometimes produce badly tarnished surfaces from which the surface deposit is difficult to remove." It has been our experience that neither of these reagents is to be entirely relied on for developing structures suitable for study or photography. This means that when the etch fails to produce satisfactory results the, specimen must be repolished, through the 000-paper at least, and then etched with another reagent. This procedure entails a con¬siderable loss of time, and the final results may not be all that might be desired. However, the reagent to be described, although not a panacea for all etching troubles, has improved results so markedly that it is felt that it is worth offering as a grain-size etch generally applicable to aluminum and aluminum alloys. Czochralski3 in 1915 mentioned the application of a solution of 10 to 20 c. c. concentrated hydrofluoric acid in 100 c.c. absolute alcohol, etching in this reagent being followed by dipping in concentrated hydrochloric-acid solution.

Jan 2, 1925

By J. C. Osmond

One of the least known geologic regions in the U.S. is the area now called the Basin and Range Province. It is paradoxical that so little geologic information has been compiled for a province that has yielded billions of dollars worth of metals and is currently producing a small amount of oil. Regional stratigraphic studies of parts of this large territory have been published only recently, and regional structural interpretations of even parts of the province are rare in the literature. This, of course, does great injustice to the earliest workers: Gilbert,1,2 Russell,9 Le Conte,4 Spurr,5 Louderback,8 and others, who recognized the area as distinctively different from the rest of North America. Their simplified picture of the structure of the ranges and the province as a whole is the groundwork for present understanding and has never been superseded. Since their early works, however, geologic data from the province has consisted largely of detailed reports of widely scattered mining districts. Each district has been described as though it were an island in an unknown sea. More recent syntheses of the geologic history have been prepared by Lindgren,7 Ransome,8 Nolan,9 Bill-ingsley and Locke,30 Longwell,11 and Eardley.12 The tentative nature of the present interpretation, which treats the structural evolution of the Utah and Nevada area, must be considered in light of the scarcity of geologic information from the province as a whole. The methods of interpreting tectonic history from stratigraphy are based largely on the concepts of Marshal Kay.23 Discussions with Hoover Mackin also have aided in organizing the Tertiary history. TECTONIC AND STRATIGRAPHIC SETTING Two approaches to the subject of the tectonic history are possible; they correspond to looking through opposite ends of a pair of binoculars. One involves an expansion and extension of detailed work and the other an interpretation based on regional geological relationships. It is believed that the second approach, used here, is not in disagreement with detailed observations. The area of the Basin and Range Province is shown in Fig. 1. Within this area middle Tertiary to Recent high-angle faulting has controlled development of mountain ranges and valleys. Only the part of the area north of Las Vegas, Nev., and south of the Snake River in Idaho will be considered in this article. Within this part of the province most of the ranges trend north-south. Approximately two thirds of the area is covered by late Tertiary to Recent valley fill and lake deposits.

Jan 1, 1961

By Samuel M. Shallcross

The principal function of the Bell limestone mine, of the American Lime & Stone Co., at Bellefonte, Pa., is to supply raw material to the company's modern rotary kiln plant at Bellefonte. Because mining costs are naturally higher than many open quarries with more favorably lying strata, it cannot compete, except to a limited extent, in the markets for road material and fluxing stone. In the broad sense, mining does have an advantage over the average open quarry when the end products are designed for and controlled by process and final inspection for the exacting demands of the industrial and chemical markets. Approximately 80 per cent of the output of the Bell mine is sold in the industrial and chemical markets. And as higher standards are set each year for construction and agricultural work, the remainder of the mine output goes to these two classes. Mining produces more fines than open quarries, and these fines are difficult to market; on the other hand, owing to absence of contaminating clay and impure rock, a greater percentage of the output of a mine is marketable. Because of the great production of fines, rotary kilns for lime burning are necessary when the stone must be mined. In 1921 the American Lime & Stone Co. operated 19 quarries and 72 lime shaft kilns spread over an area of 40 miles between Bellefonte and Altoona, Pa. At that time the lime-production capacity of the 72 kilns amounted to approximately 700 tons per day. After 15 years the company operates three rotary kilns and six shaft kilns, with a combined output of approximately 500 tons of lime per day, concentrated in its single Bellefonte plant (Fig. 1). Its only stone-producing plants are now the limestone mine at Bellefonte and a construction-stone open quarry at Union Furnace, near Tyrone, Pennsylvania. Since the middle of 1922, the management of the American Lime R. Stone Co. has been under the direction and ownership of the Warner Company, of Philadelphia. To the Warner Company's experience, gained through successful operation of lime plants in eastern Pennsylvania for many years, and the successful solution of material-handling problems

Jan 1, 1937

By Cyril Wells, Paul E. Busby, Donald P. Hart

EARLY workers in the field have established that the diffusion of nitrogen follows normal diffusion laws. Concentration-penetration data from layer analyses of reasonably pure iron specimens nitrided in an atmosphere of CO-NH, are given in the literature,' and were utilized to calculate diffusion constants for nitrogen. The diffusion of nitrogen in y-iron may be represented approximately by the equation D - 1.07x10-' e-:".'m'"'r The diflusion coefficients, D, given by this relation represent mean values, since carburization occurred simultaneously with nitriding. The rate of diffusion in a-iron has been determined from calculations based on data obtained by measuring the internal friction of samples at each of several frequencies and temperatures.' The expression for the diffusion of nitrogen in a-iron derived from these experiments is D= 1.4x10-1 e-it tudent Increasing carbon content decreases the diffusion of nitrogen in a-iron.3 Oxygen, either dissolved or combined, has been shown' to exert a marked influence on the diffusion of nitrogen from a nitriding atmosphere. D values increase rapidly with increasing amount of dissolved oxide in the metal, but diffusion is completely inhibited if preliminary oxidation has produced the slightest trace of iron oxide on the surface. Diffusion coefficients have also been calculated from permeability and solubility data,' but these values are of questionable accuracy since the boundary conditions assumed may not actually exist. Experimental Method The method selected for determining the diffusion coefficient of nitrogen in a-iron in the present investigation was the so-called fractional saturation method. This method consists of heating the specimen in an atmosphere of H2-NH8 mixtures of known composition for a predetermined time. Following this treatment, the specimen is analyzed for nitrogen; and the diffusion coefficient is calculated from a known relationship of the fractional saturation, time of diffusion, and dimensions of the specimen. This relation is based on a solution of Fick's second law and assumes that the surface of the specimen immediately reaches a given concentration which remains constant during the diffusion anneal. Tabular solutions are available4-5 and provide the relationship between fractional saturation and the quantity \/Dt /a, where D is the diffusion coefficient in cm2 per sec, t is the time of the diffusion anneal in seconds, and a, in the present experiments, is the half-thickness of the slab specimen in cm. The method is adequately discussed elsewhere.9-10 Material The material for this study consisted of 3/32 in. thick (0.24 cm) carbonyl iron plate. The major impurities in this iron are oxygen and carbon, which are readily removed by long time high temperature treatment in an atmosphere of purified hydrogen. In order to reduce the diffusion anneal time for saturation runs, some of this material was rolled to a thickness of 0.015 in. (0.038 cm) prior to the hydrogen treatment. Hydrogen treatments were carried out in a hydrogen-purified Armco iron tube heated in a global

Jan 1, 1957

By U. N. Bhrany, N. Arbiter

Over the last one hundred years the problem of assessing the efficiency of energy consumption in producing rock breakage has been studied by many investigators from a variety of viewpoints. Their contributions fall into three main categories: (1) those characterized by a priori assumptions of a relation between the energy required for fracture and the degree of fragmentation produced (e.g. Rittinged(l), Kick(2) Bond(3)); (2) those studying simple systems with controlled energy applications (Gross(4)?(5) ); (3) those treating operating data to develop practical relative measures of efficiency (Coghill(6), Taggart(7)). Closely involved in the efficiency problem is the characterization of size distributions produced by comminution. Unless an experimental size distribution can be approximated by a distribution function and its constants, it becomes difficult if not impossible to develop quantitative energy-particle size relationships. While many such functions have been proposed, none are both completely adequate and convenient. The simpler fonns usually describe only a part of the sizing data, while those which apply to a greater extent are cumbersome(8). The thesis underlying the study here reported can be stated as follows: Size reduction in a tumbling mill subjects ore particles to a relatively constant fracture-producing environment. The intensity of the forces is determined by such factors as the mass of the breaking bodies (rods, balls, rock), and the speed and dimensions of the shell. For a particular ore the extent of size reduction will depend both on the intensity and on the duration of exposure. The latter is the residence time in a batch mill, or is determined by the effective volume and the flow rate in a continuous mill. Size reduction can thus be regarded as a rate process in which the weight of material in size intervals varies as a function of grinding time. Although both the rates of disappearance of coarser sizes and

Jan 1, 1961

By C. C. Miller, A. R. Belyea, C. H. Herty, E. B. Burkart

The removal of sulfur from steel has been studied by many investigators, but the quantitative relationships between the factors involved have not been determined. This is undoubtedly due to the number of variables encountered in practice, an attempt to study any one reaction or relation being affected by other reactions the relative importance of which cannot be estimated. The factors that affect the extent of removal of sulfur in the basic open-hearth process are generally considered to be: 1. Basicity of the slag: (a) Iron oxides in the slag; (b) carbon in the metal or carbide in the slag; (c) temperature. These factors affect the reactions: FeS + CaO = CaS + FeO FeS + CaO + C = CaS + CO + Fe. 2. Amount of sulfur in the gas. 3. Amount of manganese in the metal. The factors which affect the rate of removal of sulfur include, in addition to these: 4. Fluidity of the slag: (a) Normal changes in fluidity with temperature; (b) changes in fluidity because of the addition of special reagents such as fluorspar. 5. Agitation of the bath. Within the past two years, two papers have been presented dealing with the influence of sulfur in the gas on slag and metal. Nead' has shown that if a gas high in sulfur be used for heating, the metal and slag will absorb sulfur. Whitely2 concluded from his experiments that if a

Jan 1, 1925

By P. D. White, J. T. Moss, J. S. McNiel

Results of experimental work on the in situ combustion process were first published in this country in 1953' when Kuhn and Koch described results of a three-well test in Jefferson County, Okla. Shortly there-after Grant and Szasz2 described field studies in Nowata County, Okla., in which several modifications of the basic combustion process were investigated by injection of various oxidizing gas mixtures other than air. In the past five years speculation concerning this method of oil recovery has continued, with a number of interesting papers on various aspects of in situ combustion appearing in the literature3,4,5,6,7. However, only one of these' provided actual engineering information on pattern-type field experiments. The primary objectives of the Oklahoma three-well test were to check operation of specially designed electrical ignition equipment and evaluate problems associated with initiation of combustion in a natural oil sand reservoir. Immediately following successful completion of this test in the Pontotoc sand, plans were activated for a second field experiment to be conducted in the same sand a short distance away. The objective of this second field test1 as to establish a relationship between field observations and information derived from laboratory experimentation and computations. Secondary objectives of the test were to develop operating tech- niques and define operating problems, and to obtain information that would assist in the economic and engineering appraisals of the process. Careful planning was required since this test was designed with the hope of providing basic information on the characteristics and operation of a combustion drive. It was necessary to include test facilities which would not only permit precise control and measurement of the process variables but would also provide sufficient flexibility of control to insure that variables in the combustion process could be studied during the course of the test under a wide range of conditions. In order to accomplish these objectives elaborate instrumentation and several control wells were included in the design of the test installation. This type installation was felt to be well suited for an experimental study, but was in no respect intended as a counterpart of a commercial-scale operation. PRELIMINARY LABORATORY WORK An important objective of the field experiment, as stated previously, has been to obtain reliable data on operating variables which might be compared with similar data obtained in laboratory combustion tests. The value of successful correlations between quantities that can be measured in the laboratory and those obtained in a full-scale commercial venture has been well established for other industrial processes. The difficulty of following a process underground should make such correlations even more essential here. Also. approaching the field test phase of development of in situ combustion, it was considered desirable to precede design of test equipment with laboratory combustion studies under a variety of conditions to establish likely ranges of variables. These included temperature, air injection rate, frontal advance rate and produced gas composition.

By V. J. Sikora, W. J. McGuire

Several years ago, we used an electric analogue computer to study the effect of vertical fractures on the productivity of wells in expanding fluid-drive reservoirs. The results of this work were used both as a guide to research and as a basis for the design of actual fracturing operations. In 1958, Dyes, Kemp and Caudle' published portions of the data from this study. The results were released in 1959 to service companies for use in fracturing guides. The purpose of this note is to discuss the experimental conditions and assumptions which were made to derive the information which is already partially a matter of public record. ASSUMPTIONS This study applies to fractures which extend in a vertical plane symmetrically from the well. For simplicity, we chose to study the case of a well in a square drainage area with its fractures extending toward two of its nearest neighbors. We have assumed no migration of fluid across the boundary of this area. The quadrant shown in Fig. 1 models this system. We made the usual assumptions that the reservoir is homogeneous and isotropic, that the fluid is homogeneous and that production is effected by fluid-expansion drive. We also assumed that the fracture extends from top to bottom of the reservoir. Of more practical interest is our assumption that the fracture does not change the size of the drainage area. This premise is appropriate if all the wells in the reservoir are fractured in the same way. But where a single well is fractured, its drainage area may be enlarged at the expense of its neighbors. This could be of economic importance. The assumption that the fracture will not extend beyond the established drainage area of the well also limits the application of the results. Such long frac- tures will yield benefits in excess of those predicted here. When we assume homogeneity, we disregard the frequently observed zone of damage in the vicinity of the well. Where damage is severe, the benefits resulting from by-passing it will far exceed those predicted by this study. All comparisons were made of systems producing in the semi-steady state. By this we mean that equal volumes contributed equally to flow (pressure was dropping at a uniform rate throughout the system) when the rate of flow was observed. EXPERIMENTAL SET-UP We used the pool unit of an electric analyzer' in this study. The squase drainage system of a well was rep-

By R. L. Fullman, J. W. Cahn

A method is derived for obtaining the distribution of sphere diameters and plate thicknesses (or pearlite spacings) from size distribution functions obtained along randomly oriented lines. The method described offers several advantages over existing methods. IT is often of interest to measure not only the average particle size but also the distribution in sizes of particles dispersed in an opaque material, such as an alloy. Particles of a single size will exhibit a range of apparent sizes on the plane of polish. If the sample contains a distribution of particle sizes, the distribution of observed sizes on the plane of polish is related to the distribution of actual particle sizes by an integral equation, For example, a distribution of sphere sizes, N(r),

Jan 1, 1957

By R. H. Atkinson, R. N. Rhoda

An improved technique has been developed for the deoxidation of palladium with aluminum which is especially suitable for use in making small castings with an induction-melting and casting machine. The effect of various crucible linings on the efficiency of the residual deoxidizer and accompanying oxide film in protecting palladium against oxidation during remelting also has been examined; the preferred crucible lining consists of zirconia cement. THE objective of this work was to develop a simple method of deoxidizing induction-melted palladium which would be suitable for use by manufacturers of jewelry and other small castings. In a common method of deoxidizing torch-melted palladium a piece of aluminum foil is dropped on the surface of the molten metal. If a film is present, which is usually the case, it must first be removed by oxidizing the molten metal thoroughly because it would interfere with the entry of the aluminum into the melt. Removal of the film is probably facilitated by a mild fluxing action of the silica crucibles which are used for torch-melting. However, removal of an alumina film from molten palladium in the crucibles normally used for induction melting is a much slower process and it became necessary to modify the de-oxidation procedure. In the modified procedure the charge is simply melted and the desired amount of aluminum, crimped to one end of a tungsten wire, is plunged through the film into the palladium and the wire immediately withdrawn. The trace of tungsten which dissolves along with the aluminum can be avoided, if considered objectionable, by using a palladium wire. In view of the persistence of the alumina film under the conditions of induction-melting it also was decided to ascertain the efficiency of this film in protecting palladium against oxidation during repeated remelting and casting. Melting Equipment and Materials The equipment used for melting and casting consisted of an Ecco GC:6, 6 to 8-kva high-frequency converter and an Ecco M34B centrifugal casting machine. This unit is being increasingly used for making jewelry and dental castings and it also has been found useful in making exploratory melts of a variety of nickel alloys, for which purpose it is well suited on account of its speed of melting and economy of material. A description of the machine and its operation will be published elsewhere.' A common palladium jewelry alloy, 95.5 palladi-um-4.5 ruthenium (referred to as "palladium" in the trade), was selected for the deoxidation tests. It was available as melting stock which had been melted in air to free it from oxidizable impurities, and also as clean scrap from previous melts which had been deoxidized with aluminum. The latter was thought to be typical of clean "palladium" scrap to be found in a manufacturing jeweler's establishment and it is also similar to one brand of "casting palladium." By the same token, the oxidized melting stock corresponds to "casting palladium" after the latter has been melted and thoroughly oxidized: Pure aluminum wire (99.9 pet), 0.032 in. diam; 1 in. = 0.036 g. Scrap tungsten wire, 0.014 to 0.020 in. diam. Argon, commercial water-pumped; 99.9 pet pure Experimental Procedure Samples of about 50 to 75 g of the palladium alloy were melted in a crucible lined with a proprietary refractory alumina cement. Some charges were melted in air, others in argon. The oxidized melting stock was melted and solidified a number of times in order to remove as much oxygen as possible before deoxidizing, but this treatment was unnecessary in the case of scrap. In either case the metal was deoxidized with aluminum (0.01 to 0.05 pet) by the

Jan 1, 1959

By P. Niessen, W. C. Winegard, C. J. Beingessner

DURING the last 10 years, several grain-growth studies have been made using zone-refined metals with controlled amounts of solute to elucidate the interaction of solute with moving boundaries. In all these studies, it was more or less implicitly assumed that the alloys used were, after recrystallization and grain growth, homogeneous within the grains with respect to solute and lattice defects. This note deals with observations made on microstructures originating from solidification of dilute alloys and from grain growth. Briefly, the experimental procedure used in these studies was the following: zone-refined cadmium and master alloys were melted and cast in Pyrex under vacuum to produce bars 14 mm in diam and about 150 mm long. These bars were cut into 8-mm-thick slices which were mechanically and chemically polished. The specimens were then deformed 30 pct in compression and given a 1-week anneal at 260°C in argon. After this anneal, a second deformation produced completely recrystallized samples 4 mm thick. The time-temperature controlled anneals were carried out in a bath of silicone oil. After the grain-growth anneal, the specimens were polished in Gil-man's' solution (33 g CrOs, 6 g NazSO, in 100 ml of water). Several etches were used depending on the alloy investigated, but mostly a mixture of concentrated HC1 and HNOj (98:2 vol) was employed. In all the alloys examined, the ease with which substructures could be revealed depended strongly on the crystallographic orientation of the surfaces of the grains. However, very frequently the microstructures to be discussed here etched up over broad areas comprising several grains. Fig. 1 is a micrograph of a Cd-0.05 at. pct Mg alloy annealed for 100 sec at 270°C. Different substructures are seen in this photograph. A denotes the now existing grain boundaries. The well-defined lines and points marked B are the remains of a solidification substructure. The lines are boundaries between cell colonies, and the points are nodes located on regular two-dimensional cells. This cellular structure has the same appearance as that found by weinberg2 for rapidly quenched Zn-Au alloys. The "ghost boundaries", marked C, are very similar in appearance to a grain boundary array in a polycrystalline sample. Repeated polishing and etching showed that all the substructures observed were three-dimensional. To date, the ghost boundaries have been clearly observed in all samples containing 0.005, 0.01, 0.05, and 1 at. pct Mg, and in samples containing 0.01 at. pct Zn. Attempts to outline these ghost boundaries in cadmium alloys containing 0.01 at. pct Ag and Au were only partially successful. In these alloys, parallel lines, having a resemblance to the ghost boundaries in the Cd-Mg and Cd-Zn alloys, were observed, but it was not possible to obtain complete arrays of ghost boundaries which extended over several grains. It is possible that a different etch than that presently employed would reveal the ghost boundaries in the Cd-Au and Cd-Ag alloys as clearly as in the Cd-Zn and Cd-Mg alloys. A close examination of the ghost structure showed that it consisted of linear etch-pit arrays, Fig. 2. The ghost boundaries were resolvable even in grains which showed over-all faceting due to the etching, as seen in the corner of Fig. 2. The general appearance of the ghost structure suggests that it originated during grain growth. This is supported by the observation that the mesh width in the ghost-boundary array generally increased with increasing final grain size. To test whether the ghost structure was formed during the long homogenizing anneal or during the grain-growth anneal, some as-cast samples were deformed and given a grain-growth anneal. This anneal was terminated by air cooling or

Jan 1, 1967

By R. J. Watson, A. H. Juch

About half a million sucker-rod pumps are installed in oil wells in the U. S. alone. In Venezuela, too, the system is widely used; some 5,000, or 90 percent, of Cia. Shell de Venezuela's wells produce a total of 400,000 BOPD by this method. Most of the crude pumped is viscous, gassy and contains relatively small amounts of free water. API gravities vary from 90 to 16O; dead oil viscosities vary from 10 to 10,000 cp at the pump; and GOR's range from 100 to 2,000 cu ft/bbl. Pumps are set at depths ranging from a few hundred to 6,000 ft; the average setting depth is about 2,500 ft. From the literature, it appears that although recent years have seen significant progress toward understanding the rod pumping system as a whole, relatively little attention has been paid to those key items, the sucker-rod pump and the subsurface gas separator or gas anchor. Perhaps because of proration in the U. S., pump manufacturers have seemingly concerned themselves more with the durability of their product, achieved mainly through robust design and metallurgical know-how, than with its working efficiency. In 1963, CSV commenced a major rehabilitation and expansion of its heavy oil fields along the Bolivar Coast. The advent of the more efficient gravel-packed completion and of large-scale thermal recovery (mainly steam soak) operations resulted in well potentials *Now with B. I. P. M., The Hague, The Netherlands. greater than pump capacities. Hence, an urgent need arose to improve over-all pump efficiencies and to attack those special problems related to the production of both the extremely viscous and the hot, steam-laden crudes that formed an increasing proportion of the total stream. There followed a detailed investigation and testing program, carried out in close cooperation with a major pump manufacturer. This culminated in the introduction to the oil industry of a new line of sucker-rod pumps. Early Investigations and Experiments Field Tests Extensive field tests were carried out in three primary Bolivar Coast wells with an in-situ dead oil viscosity ranging from 400 to 6,000 cp. In these installations provision was made to (1) monitor bottom-hole pressures below, in and above the pump by means of pressure transducers, and record casing- and tubing-head pressures continuously; (2) measure accurately the annulus gas, as well as measure the tubing gas and liquid production from the well; (3) take special PVT samples of the well fluid; (4) measure power consumption of the prime mover; and (5) measure the rod loads at the polished rod. A typical test installation is illustrated in Fig. 1. It was established from the pressure transducers that with viscous oils, there is considerable flow resistance across the pump and gas anchor assembly. Pressure surges were observed over each pump cycle,

Jan 1, 1970

Large deposits of manganiferous iron ores, representing several million tons of metallic manganese, occur in the United States. The Minnesota deposits of such ore are of outstanding importance because of their size, state of development, ease of mining and proximity to the Great Lakes, which permits water transportation to steel centers. In view of the fact that our steel industry requires large quantities of manganese, for which no satisfactory substitute has been found, and because our reserves of ferro-grade ore are comparatively small, the development of methods that will make our large deposits of manganiferous iron ores available as a source of ferromanganese is an important problem. Realizing the importance of this problem, some years ago the North Central Station of the U. S. Bureau of Mines and the Minnesota School of Mines Experiment Station undertook jointly the development of methods for recovering the .manganese content of manganiferous iron ores in a form suitable for the production of ferromanganese, the 80 per cent. alloy indispensable in producing steel. Two types of manganiferous iron ores have been described in previous reports.' The brown ores are higher in iron and lower in manganese than the black ores; the black ores are more siliceous but contain less phosphorus. The utilization of the iron content of the brown ores in the production of steel appears to furnish the best basis for their treatment. The method of attack has been to work out modifications in iron and steel practice so as to recover manganese in the form of slag comparable to ferro-grade ores. The greater part of the experimental work has been conducted with a 6-ton blast furnace and a 1/2-ton basic open hearth. This paper is devoted mainly to open-hearth tests in which high-phosphorus spiegel

Jan 1, 1930

By K. E. Brown, J. P. Brill, A. R. Hagedorn, T. C. Doerr

A recent correlation for multiphase vertical flow by Hagedorn and Brown1,7 has been used to examine the effect of numerous variables such as pipe size, gas-liquid ratio, liquid flow rate, liquid viscosity, liquid surface tension, oil API gravity, water cut, etc., on flowing pressure gradients. Most previous correlations were derived by using a form of the general energy equation which assumed negligible changes in kinetic energy. Under certain flow conditions this can lead to serious errors in predicting pressure traverses. Examples of traverses calculated both with and without the kinetic energy term are included here. The Chew and Connully correlation for calculating changes in viscosity with changing pressure and temperature has been extended so that the effect of a changing viscosity with depth on pressure gradients can also be predicted. Examples illustrating the effect of tubing size show the importance of this correlation in determining pipe sizes for initial well completions. Limitations on production rates in small pipe sizes from excessive friction losses can be predicted with greater accuracy. The combined use of a vertical-flow correlation with a horizontal-flow correlation provides a method for determining the maximum flow rate possible from both flowing and gas-lift wells. Examples are included to illustrate application of the combined use of vertical and horizontal-flow correlations in optimizing production rates and minimizing excessive costs from over injection of gas in gas-lift wells. INTRODUCTION The problems of multiphase vertical and horizontal flow are immediately encountered in any producing well. Fig. 1' shows three stages of production: flow in porous medium, vertical flow and horizontal flow. All three stages affect the production rate from a well. If we are confronted with a particular well and consider only the variables involved in the vertical and horizontal stages of Fig. 1, we should be capable of calculating the flowing bottom-hole pressure necessary to produce a particular flow rate. A change in any of the variables results in a new solution to the problem. Recent approaches in developing horizontal and vertical-flow correlations have improved to the extent that the solution can now be obtained with more confidence than previously. VERTICAL AND HORIZONTAL FLOW CORRELATIONS Since Poettmann and Carpenter's' original work in multiphase vertical flow, there have been many additional vertical-flow correlations developed which have greatly improved the accuracy of pressure-loss calculations. These

Jan 1, 1967

By Edna A. Dancy, Gerhard J. Derge

Jan 1, 1963

By P. van Meurs, C. van der Poel

From observations of the linear displacement of oil by water from a porous medium as visualized in transparent models, new insight into the mechanism of vircous fingering, as occurring in the case of unfavorable oil-water viscosity ratios, has been obtained. A mathematical description of the observed phenomena leads to formulas. expressing both oil production and pressure drop across the formation as a func-tion of cumulative water injection with the oil-water viscosity ratio as a parameter. Theoretical results are compared with those obtained from scaled laboratory experiments in sand-filled rubes in which water was injected at the one end and production was obtained from the other end. In the second part of the paper the same principles are used to calculate a more realistic production scheme in which production of oil and water is obtained from wells regularly distributed over the field. Results show satisfactory agreement with production data of an actual oil field. Application of the theory is extremely simple as only a limited number of readily available parameters have to be known and results are presented in an analytical form. INTRODUCTION When oil is displaced from a porous medium by water having a viscosity lower than the oil. the oil-water interface is essentially unstable and has the tendency to break up into what are called "fingers" or "streamers". This Viscous fingering has been noted before by Engelberts and Klinkenberg' and has recently been demonstrated in transparent models by van Meurs-. It is highly questionable whether it is at all possible to perform relative permeability measurements In the laboratory reproducing the same distribution of water and oil in the cores as Present in practice. Therefore, we based our descriptive theory on an idealized model which was "tailored" to the fingering mechanism as observed in transparent models under scaled conditions. This approach was the more attractive, as a highly simplified model had already yielded an adequate description of the process. Though we are aware our theoretical approach can be extended in several ways, it is given here in its simplest form to explain the fundamental principles and to avoid complicated formulas. SIMPLEST CASE OF A LINEAR DRIVE Observations and Theoretical Model In Fig. 1 a series of photographs shows how water penetrates into a formation saturated with an oil which is considerably more viscous than the water. The technique for obtaining these photographs, using transparent models, has already been described?. The fingers can be clearly observed and are seen to be mainly parallel to the flow direction. Note that the contours of these fingers are not smooth but show protrusions of water enclosing oil pockets.

By H. H. Bein

Most western industrial sands are feldspathic and contain feldspars in variahle amounts. A few deposits will show alumina contents of less than one per cent while others will contain over twelve per cent alumina. Some industries are not especially concerned with the amount of contained feldspar but are interested only in color and in size gradations. Other industries, however, are very much interested in alumina content and set up quite rigid specifications as to this content. Several western plants are beneficiating crude sands both to reduce the iron content and to control the feldspar content. At present, most of these plants are using flotation processes for both controls although a few plants do use magnetic separators for the reduction of iron content. Some work has also been done with electrostatic separators for the feldspar-quartz splits. The Sand Division of Del Monte Properties Company, Pebble Beach, California, has been operating a flotation plant for iron removal and the separation of quartz and feldspar since 1950. As mentioned before, control of alumina, especially in the quartz product, is very important. Some users require an alumina content of less than two per cent and others will demand a product of less than one per cent Al2,O3,. The standard Quinolate method for determining alumina is lengthy and time consuming. The HF —H2SO4 evaporation step is especially critical and, if forced, spattering is apt to occur with a resulting loss of sample. Standard procedure is to evaporate to dry ness overnight at a low temperature. Even with forcing under optimum conditions the procerlnre will take two or three hours to complete. A new method has been developed which allows an alumina determination to be made, in 10 or 15 minutes, on a sample of the quartz product as it is being produced. This pocedure, although simply an approximation, has been most helpful in showing whether or not the product being formed is meeting specifications. This procedure has also allowed a great reduction in samples formerly taken and analysed by the orthodox method. Whether a sample assays 1.75% A12O3, or 1.95% .41,0, is not so important as the fact that it is below the allowable maximum of 2.00%. Similar thinking would apply to products required to contain less than 1.00% A1,0,. The step by step procedures for the method are as follows: 1. Collect sample, drain or filter, and dry. 2. Split sample through standard Jones sample cutter to quarter or eighth sample, depending on size of original sample taken, then split down to about 5 grams through Sepor micro-splitter. 3. Screen through 50 mesh sieve (U.S. Series) and reject undersize. 4. Weigh out 2 grams and place in platinum crucible. 5. Etch with 3-5 mls 38.40% HF for 1 minute at room temp. 6. Decant and wash. 7. Stain for two minutes in same crucible with a 1% water solution of Nigrosene dye. 8. Decant and wash well. 9. Dry.

Jan 1, 1961