Search Documents

By Jiwei Duan

The energy transferred from a hammer to the pile top is considered as the effective energy in this paper. The effective energy is related to the pile dimensions, soil and pile-soil interface properties. This relation may be expressed as an equation based on the dimensionless theory. The relationship between pile capacity and effective energy was studied by performing a series of wave equation analyses using a commercial software called GRLWEAP (Wave Equation Analysis Program) by GRL Engineers, Inc. The results show that the pile capacity increases with the blow count when the effective energy is constant, however, it has a little change as the blow count is over 100 blows per foot. The pile capacity decreases as the ratio of pile penetration depth to pile diameter increases if the effective energy is constant. The pile capacity will increase as the pile diameter and wall thickness increases if the effective energy is constant. The pile stickout (pile length above the ground surface) does not have a significant effect on the effective energy and may be neglected. Curves for pile capacity versus effective energy are presented to be used for preliminary hammer selection according to effective energy and hammer efficiency. Finally, a case from PDA testing was studied. Measurements of the effective energy and pile capacity by CAPWAP were presented and compared with the results by GRLWEAP.

Jan 1, 2006

By F. Burat

Large reserves of feldspar ore exist in the Aegean region of Turkey. The main colored impurities in these ores are iron- and titanium-bearing minerals such as anatase, rutile, sphene and ilmenite. In this study, a potassium feldspar ore containing mainly quartz and coloring impurities was subjected to beneficiation tests involving magnetic separation and flotation, which were applied either separately or in combination. Bench-scale flotation experiments using cationic collectors G-TAP and Flotigam V-4343 and using HF and H2SO4 as modifiers were employed to separate feldspar from quartz and to remove part of the titanium impurities. The best results were achieved with a combination of high-intensity wet magnetic separation and flotation. A feldspar concentrate containing 16.28% Al2O3, 10.75% K2O, 2.84% Na2O, 69.97% SiO2 and 0.16% Fe2O3 was produced. A quartz concentrate containing 2.30% Al2O3, 0.48% K2O, 0.42% Na2O, 0.07% Fe2O3 and 96.20% SiO2 was also obtained

Jan 1, 2007

By Geoffrey Fosbrook, Donald Phillips, Anil Parikh

The Second Avenue Subway is a $16.8 billion project planned by the Metropolitan Transportation Authority (MTA) in New York City. It will reduce overcrowding and delays on the Lexington Avenue Line, improving travel for both city and suburban commuters, and improving access to mass transit for residents of the East Side of Manhattan. The project is a new, two-track, 13.5 km (8.5 mile) subway extending from Lexington Avenue at 125th Street in Harlem on the north end of Manhattan, to Water Street at Hanover Square in Lower Manhattan. The first phase of construction includes rock tunnels from 92nd Street to 62nd Street and connection to the existing 63rd Street station, three new stations, and track and systems from 105th Street to 63rd Street, allowing service between 96th Street and Brooklyn via an existing Broadway Line. The following describes the Project in detail, discusses the construction challenges addressed in the design, and the initial design/build contract to be awarded in 2005. A discussion of the planned mined construction of two rock caverns and a cut-and-cover station construction are also included.

Jan 1, 2005

Project cost control procedures and computer systems have enjoyed a successful and simple relationship over the past decade, thanks primarily to the proliferation of portable computers or PC's. Prior to the introduction of this technology, project control was largely a manual and somewhat onerous task of historical data compilations, with little time available for dynamic forecasting, staged planning, or pre-emptive cost control. Automated systems developed during this era were resident on "Heavy Iron" or mainframe computers and were expensive to maintain and operate. Use of these early systems was limited to large engineering, construction, and industrial concerns with the economies of scale and funding required for their successful application. Systems were either designed for critical path analysis or task scheduling, but rarely integrated with the other, much less cost control.

Jan 1, 1990

By John Hoffert, Darren Colwell, Greg Tucker, Jeremy Kinch, Greg Rasmussen

"The Kemess Mine, a major producer of gold and copper, is located in north-central British Columbia. Kemess was brought into production in May 1998 by Royal Oak Mines. On February 11, 2000 Northgate Exploration Limited acquired Kemess Mine from receivership. Since acquisition in 2000 Kemess has seen many accomplishments, including the reduction of costs by 40%.One of the largest site capital costs was the construction of the tailings storage facility dam, which when finished will be one of the largest earth filled dam structures of its type. The existing construction design by AMEC called for a kilometer wide rock dam to be built from the 1350 M elevation to the 1504 M elevation at a 5.5:1 slope by hauling over 30 million tonnes of non-acid generating waste rock 7-kilometers from the open pit to the tailings dam, which was highly expensive.Kemess realized an opportunity for cost reduction was possible if the dam could be built from suitable quality tailings sand; however the sand did not meet the neutralizing potential ratio specifications. It was determined that cycloning combined with flotation to reduce pyrite concentration in the sand would produce a non-acid generating product for dam construction. The sand plant design challenges were to remove the sulphides from the tailings to obtain an NPR greater than 2:1 and provide a consistent sand product for the construction with a fines content of less than 15% passing 200 mesh. After a 2-year testing design and construction period, the sand plant was successfully started at the end 2002 resulting in higher than expected sand quality and production rates.This paper describes the plant design phase, commissioning, and operation of the tailings sand plant for construction of the tailing storage facility dam to enable us to meet all the engineering and regulatory requirements. The many challenges faced were successfully met using several innovative designs. The operational, economic, and environmental benefits are detailed."

Jan 1, 2004

By D. Harrington

A uniform hoisting-signal code for mines hoisting from more than one level, if adopted by all mining States, would be beneficial to employees and owners alike and should largely reduce the number of hoisting accidents. Misunderstood hoisting signals cause many shaft accidents involving injuries to men, damage to equipment, and loss of production from the resultant delay. Many of the metal-mining States have adopted codes for hoisting that are effective within the borders of that State but usually entirely different from the signal code, if any, in use in an adjoining State. For many years safety engineers have recognized this lack of uniformity as a distinct hazard, but a uniform code has never been adopted by the States or by the mining industry in those States that have not incorporated signal codes in their mining laws or mining regulations.

Jan 1, 1944

By Gray Mullins

A post grouted drilled shaft foundation system was successfully used in place of the specified driven pile foundation system as a Value Engineering Cost Proposal (VECP) for the new PGA Boulevard Grade Separation Project. Pressure grouting the cohesionless sandy soils at the drilled shaft base significantly increased the end bearing capacity and stiffness allowing drilled shafts to be the more cost effective foundation system. The post grouted drilled shaft option also provided other benefits including reducing owners risk normally associated with pile driving vibrations and offered a high level of quality assurance for the drilled shafts. This paper discusses the implementation of post grouted drilled shafts from design to completion of construction. A design procedure for post grouted drilled shafts developed by the University of South Florida was used for initial VECP evaluation. Prior to construction, two instrumented test shafts were installed and load tested, one of which was post grouted. Therein, the design procedure was calibrated, tip elevations for production shafts were refined, drilled shaft construction and grouting procedures were demonstrated, and a grouting criteria was developed for the project.

Jan 1, 2003

By Sandeep Kumar Jeripotula, Govinda Raj Mandela, Aruna Manglapady

Dumper operators are frequently exposed to whole body vibration (WBV) in surface mines. Surface mining activities involve the amalgamation of comparatively high intensity of vibration and extended exposure durations. Efficient risk reduction mandates knowing of important phases of a task that poses a threat to health of dumper operators. So far in India very limited studies have been reported on WBV exposure with regard to surface mines. This paper evaluates WBV of dumper operators based on ISO 2631-1:1997 Standards and European Union (EU) Directive 2002 for different phases of job cycle. Six dumpers were considered for this study and the vibration measurements were made for all the four phases of the job cycle by placing the triaxial accelerometer on the operator’s seat-surface and at the seat-back, independently. The findings of the study revealed that the haulage task (loaded travel and empty travel) remains the chief contributor to vibration exposure according to seat-surface and seat-back measurements. Maximum frequency weighted root mean square (RMS) of 1.12 m/s2 and 1.09 m/s2 were reported for empty travel task for seat-surface and seat-back measurements, respectively. For seat-surface measurements based on RMS, Z axis remains as the dominant axis of vibration for all the dumpers during haulage task, whereas for seat-back measurements, the dominant axis varies between X and Y. Exposure action value (EAV) based on RMS has exceeded the threshold value of 0.5 m/s2 for all the dumpers during loaded travel and empty travel for seat-surface as well as for seat-back measurements.

By J. O. Osterberg

The realities of foundation enginering are that the work never proceeds exactly as expected. The various reasons, exploration, design, construction, and legal are discussed. Case histories are presented with an analysis of why the projects did not turn out as expected and how the difficulties might have been avoided.

Jan 1, 2010

By S. E. Phillipson

Underground mine mapping is a critical component of understanding the controls on ground instability. Many relatively localized examples of ground failure are associated with geologic features, such as faults, joints, compaction zones, or sedimentological transition zones. In contrast, long-running, directional roof falls are associated with regionally directed horizontal stress fields, which are induced by tectonic plate interactions in the earth?s crust. When stress-related features are distinguished from geological features, underground mapping can be an effective method for inferring the direction of horizontal stress at individual mines. Comparisons with data compiled in the World Stress Map confirm that underground mapping can be a valid method for determining the orientation of maximum principal horizontal stress at a variety of scales, ranging from individual mines to an entire mining district or coal basin. Comparisons are presented between the maximum horizontal stress directions inferred by MSHA?s Roof Control Division through underground mapping and the azimuths of maximum horizontal stress in the World Stress Map database for North America?s Pennsylvanian-aged Appalachian, Illinois, Black Warrior, and Arkoma Basin coal fields. The comparison indicates that azimuths are similar for both data sets, even where variations in the direction of horizontal stress are present. It is interpreted that inconsistencies in direction are attributable to near-surface affects such as deeply incised stream valleys, or to fault zones that represent heterogeneities in the crust.

Jan 1, 2009

By Zengjie Wang

Kinetic study of hydrochloric acid leaching of Panzhihua ilmenite from China is presented. Both temperature and concentration of hydrochloric acid have significant effects on the rate process of Fe dissolution from ilmenite ore, while the ratio of liquid to solid has little effect on the Fe dissolution. The Fe dissolution is found to follow the spherical model f (??) =1-(1- ??)1/3 and the apparent activation energy is calculated as 47.21 KJ/mol, suggesting a chemical reaction controlled mechanism. The dissolving behaviors vary at different kinetic stages. At the beginning the amount of the dissolved Fe and Ti increased monotonically with leaching time, while about 15 minutes later the dissolved Ti in the form of TiOCl2 began hydrolyzed into TiO2 fines reunited on the ilmenite ore surface, as observed by SEM and EDS technique. For the unreacted ilmenite particles covered by a layer of hydrolyzed TiO2, the leaching seemed to be as a selective leaching of iron and because Ti dissolved from and hydrolyzed rapidly again into the unreacted ilmenite particles. The leaching process can be ended 4 hour later when almost of Fe has dissolved into the solution and TiO2 remains as solid residues. The effects of acid concentration and leaching temperature were also investigated.

Jan 1, 2009

By P. A. Davies

Paper presented at the conference: Risk assessment in the extractive industries, held in Exeter, UK, 23-24 March 1994, and first published London: IMM, 1994, preprint volume, 11pp., 15 refs. Hazards such as vibration, dust emission and fragment projection can result in an area called the Danger Zone being set around a blasting site. Traditionally Danger Zones have been set solely on the basis of consequences (e.g. based on the maximum distance of rock projection or expected ground vibration plus a defined safety margin). Advances in risk assessment and its growing acceptance as a safety management tool have led to the setting of Danger Zones based on both consequences and frequency of occurrence. This allows distances to be optimised on the basis of acceptable risk levels rather than the potential consequences of infrequent events. The setting of a flyrock Danger Zone is used to demonstrate a risk-based approach compared with a traditional consequence approach

Aug 1, 1995

By Ove Alm

Wet and dry specimens of three rocks of approximately granitic composition were deformed at different experimental conditions. These experiments were carried out in order to study the extent to which water, either added or released from mineral reactions, may affect the mechanical properties and the microstructure of these rocks. The experiments were conducted in a Griggs&apos; hot creep apparatus at temperatures and pressures up to 900ºC and 1000 MPa respectively; and most of them were performed in the constant strain rate mode [(1.10-6 < t < 1 • 10-4 s-1 )]. All three rocks were low porosity rocks, and the wet specimens never contained more than 0.9 wt % of added water. The experimental results are, however, quite unequivocal: They show that wet rocks are weaker than dry ones. A significant difference is even found for rocks tested in uniaxial compression at room temperature. A few experiments carried out on specimens obtained from larger prestressed rock cores indicated that the central parts of these cores were more likely to contain more microcracks than the ends. Optical microscope examinations revealed that extensive microcracking takes place even at the highest temperatures, where other mechanisms such as slip and dislocation creep also become important. Very little partial melting could be observed except for the specimens deformed at 900ºC.

Jan 1, 1982

By E. H. Smith

"The El Indio mine treats a complex mixture of copper and gold/silver ores at its plant located in the high Andes in Chile. The plant utilizes conventional crushing, grinding and flotation to produce a copper/gold/silver concentrate. Due to high levels of arsenic and antimony, the flotation concentrate must be roasted prior to custom smelting. The flotation tailings is leached and additional gold recovered from a CIP circuit. Present and future metallurgical developments are discussed in this paper. INTRODUCTIONIn late 1989, LAC Minerals purchased 65 % of Bond International Gold and as a result became controlling shareholder of the El Indio Mine through Bond and San Jose.El Indio is a world class, complex sulphide gold deposit located in the hydrothermal alteration belt of the Andes mountains in the 4th Region of Chile. The mine is located in the high Andes about 185 km east of La Serena at an elevation of 4000 meters. The 1450 workers at El Indio live in the mine camp at 3200 m and on days off are bussed to La Serena.The El Indio mine was started in 1979 by St. Joe Minerals Corp., bought by Bond in 1987 and subsequently by LAC in 1989. The mine has produced 2.7 million oz. of gold, 9.5 million oz. of silver and 170,000 t of copper since start of operation. The mill is currently operating at a rate of 2850 t/d and producing a copper/gold concentrate which is roasted to produce a copper/gold calcine and high quality, saleable crude AS2O3 . A small proportion of the precious metals are also produced as bullion from the leach circuit.Total production during 1989 was 224,197 ounces of gold, 1,309,342 ounces of silver and 26,968 tonnes of copper. The average cash cost of production for the period was U.S. $96 per ounce of gold, net of by-product credits. The average realized price was $5. 30 per ounce of silver and $1.14 per pound of copper."

Jan 1, 1991

By R. E. Mussier

This investigation was made to study new methods to prepare high-purity yttrium metal, Various methods were used to prepare pure intermediate compounds, primarily chlorides, bromides, and iodides, which were subsequently reduced to metal. The process found most suitable for the preparation of pure anhydrous yttrium chloride involved thermal dehydration of a mixture of hydrated yttrium chloride and ammonium chloride while under vacuum. Yttrium bromide and iodide were prepared most effectively by the direct halogenation of yttrim carbide. Yttrim carbide was obtained by reacting and melting yttrium oxide-carbon mixtures in a carbon-arc furnace. Yttrium halides were purified by vacuum distillation and reduced by alkali or alkaline-earth metals. Lithium and sodium proved to be the best reductants from the standpoint of yield (>95 pct) and purity (>99.8 pct) of the yttrium. The product of the reduction step was sponge metal, which was consolidated readily by conventional cold-mold, arc-melting procedure. The purest yttrium obtained in laboratory scale work was prepared by sodium reduction of yttrium chloride and contained only 125 pp oxygen; other impurities did not exceed 1,000 ppm. In larger scale tests yttrium containing only 800 to 1,000 ppm total impurities was obtained by lithium reduction of yttrium chloride. The tensile properties of high-purity yttrium were determined. Mechanical tests showed that yttrium can be forged, extruded, rolled, spot welded, and deep drawn.

Jan 1, 1963

By R. G. Benson, P. R. Wotruba, K. W. Schmidt

Introduction The Fortitude deposit is located in Nevada&apos;s Battle Mountain mining district in the central Great Basin region of the Basin and Range province of the western US. The deposit is at Copper Canyon in the southernmost portion of the district, about 19 km (12 miles) southwest of Battle Mountain (Fig. 1). Mining activity in the district began in 1866 (Roberts and Arnold, 1965). Base and precious metals were mined by underground methods intermittently until 1955. Placer gold was first discovered at Copper Canyon in 1912. Moderate scale dredging of alluvial gravel at the mouth of Copper Canyon was conducted by the Natomas Co. from 1944 to 1955 (Johnson, 1973). In 1967, Duval Corp. began large scale open-pit copper mining. (Sayers, Tippett, and Fields, 1968). Copper prices decreased and precious metals prices increased in the mid-1970s so Duval&apos;s exploration efforts at Copper Canyon shifted to precious metals. These exploration efforts resulted in the discovery of the Tomboy-Minnie deposits and shortly afterward, the Northeast Extension deposit at Copper Canyon (Blake, Wotruba, and Theodore, 1984; Fig. 2). The Fortitude deposit was discovered in late 1980, after Duval had proceeded with precious metals production at Copper Canyon. Converting the existing plant facilities at Copper Canyon to a precious metals recovery system was completed in 1978 (Jackson, 1982). Production from the Tomboy-Minnie deposits began in early 1979. Precious metals production moved to the Northeast Extension deposit in 1982. In late 1984, after three years of preproduction stripping and mining of the Upper Fortitude ore zone, production from the higher grade Lower Fortitude ore zone began. Currently, Battle Mountain Gold Co. operates the Fortitude deposit. Production from the Battle Mountain mining district before 1967 included 4.6 t (150,000 oz) of gold, 65.3 t (2.1 million oz) of silver, 13.6 kt (15,000 st) of copper, 4.5 kt (5,000 st) of lead, and 13.6 kt (15,000 st) of zinc (Roberts and Arnold, 1965). At the time of Duval&apos;s 1967 start-up, ore reserves at Copper Canyon included 12.6 Mt (14 million st) in the East ore body and another 3.6 Mt (4 million st) in the West ore body. Both had average grades of 0.79% copper, 16.1 g/t (0.47 oz per st) silver and 0.86 g/t (0.025 oz per st) gold (Blake et al., 1984). The Tomboy-Minnie deposits collectively contained 3.5 Mt (3.9 million st) of ore grading 3.09 g/t (0.09 oz per st) gold and 9.6 g/t (0.28 oz per st) silver. The Northeast Extension reserves were identified as 1.4 Mt (1.5 million st) of ore with an average grade of 2.9 g/t (0.085 oz per st) gold and 5.1 g/t (0.15 oz per st) silver. Initial total reserve estimates for the Fortitude deposit were 14.5 Mt (16 million st) grading 5.14 g/t (0.15 oz per st) gold and 29.8 g/t (0.87 oz per st) silver (Jackson, 1982). Therefore, before large scale mining, the Copper Canyon area contained a minimum of 102.6 t (3.3 million oz) of gold and 541 t (17.4 million oz) of silver as mineable reserves. The Fortitude deposit reserves as of Jan. 1, 1985 were 10.6 Mt (11 million st) grading at 5.28 g/t (0.154 oz per st) gold and 28.5 g/t (0.83 oz per st) silver. Currently, the company is producing 6.8 t (220,000 oz) of gold and significant amounts of

Jan 7, 1986

By C. Nexhip, S. Sun

Critical to understanding and controlling phase mixing and separation in metallurgical processes, is the development of reliable experimental techniques to measure interfacial properties of melt systems. A series of experiments has been carried out to determine the effect of oxygen potential on the surface tension of liquid copper. Using an electromagnetic levitation method, a surface tension-oxygen chemical potential adsorption isotherm was produced for the Cu-O system at T 1400 K. The surface tension results show good agreement with the literature values e.g. within 3 per cent for pure copper. The Belton `ideal&apos; adsorption isotherm was applied, and the following equation derived to best fit the experimental data ? =1251-77.5 1n41+ (2.79x105 . pO1/2)](mN.m Using this equation, the surface tension of copper was calculated/predicted as a function of oxygen potential at 1400 K, and showed excellent agreement with the experimental values. This confirmed that the adsorption behaviour of oxygen in liquid copper is ideal. The saturation coverage of oxygen on the surface of liquid copper was determined to be T0 = 6.65 µmoles.m,-2 corresponding to an area per adsorbed oxygen atom of ao ? 25 Å2. These values agree well with those cited in the literature, and our experimental data cover a very wide range of oxygen potential (10-5 to 10-17 atm). Keywords: levitation melting, surface tension, Cu-O alloys, oxygen potential, adsorption isotherm, surface coverage.

Jan 1, 2004

By James Ridenour

This report represents the first comprehensive accounting of lode mining sites in the Loon Creek mining district, Custer County, Idaho. Thirty-five mine and prospect locations have been added to the Bureau&apos;s Mineral Industry Location Subsystem (MILS) data base as a result of initial phases of a mineral appraisal of the River of No Return Wilderness; previously known locations were field checked and the updated information added to the data base. The district&apos;s major deposits are gold-copper-silver fissure-fillings hosted by biotite schist intruded by dikes ranging in composition from rhyolite to lamprophyre. These deposits contain a trace element suite similar to Tertiary pink granites and may be related to intrusion of the nearby Casto pluton. Continued firm gold prices could stimulate the search for precious metal occurrences in this and other mining districts in central Idaho.

Jan 1, 1983

Deposits of the Reefton Goldfield, West Coast, New Zealand, are hosted on N-NE striking, upright folds of the Greenland Group. High-grade quartz lodes are hosted on axial planar shears, typically have short strike lengths, and form shoots that pitch steeply on the hosting shears. Deposits within the field area of a detailed structural study share these characteristics. Field mapping and microstructural analysis have demonstrated that the Greenland Group was affected by a multideformational sequence. Gold mineralisation is hosted on shears axial planar to the F2 folds, but occurred during a subsequent deformation event (D4). Deformation during D4 resulted from N-NE directed shortening, near parallel to the trend of the F2 folds. This event produced F4 kink folds that were accommodated by layer parallel slip on S2 parallel shears, gold mineralisation during D4 being confined to the dilational hinges of F4 kink folds. The semi-brittle nature of D4 allowed the formation of stockwork veining and disseminated mineralisation within the F4 hinge zones. Most deposits within the goldfield are similar to those within the field area, and are interpreted to have been mineralised during D4. The two largest known deposits within the goldfield, however, are distinct. The Blackwater Deposit, striking parallel to the hosting folds, has a combined strike length of 1 km. The Globe-Progress Deposit is hosted on an E-W striking discordant shear in which a brittle zone of disseminated mineralisation encompasses high-grade quartz lodes. The characteristics that distiguish the Globe and Blackwater deposits may be due to formation before and after D4 respectively. Detailed field mapping in the vicinity of known deposits throughout the goldfield will further refine the relationships between the F2 folds, later deformations and the localisation of ore deposits. Additional mapping may also help constrain the position, orientation and extent of additional orebodies.

Jan 1, 2001

By Howard A. Perko

Soldier pile and lagging is a conventional means of temporary excavation shoring. Timber lagging design has traditionally been based upon the designer&apos;s experience or empirical rules. One such method is the Goldberg Zoino chart used by the Federal Highway Administration. Most of these methods restrict the designer to a consistent soil profile, certain pile spacing, construction grade timber lagging, and limited depth. The methods do not take into account surcharge loads or a variety of other factors that could arise. A designer working outside of ordinary circumstances with unusual loads, varying soil conditions, or alternate lagging materials has difficulty estimating lateral earth pressures. In rigid earth retention systems, lateral earth pressure is generally assumed to be constant along the length of the wall. In soldier pile and lagging systems, the lagging is often considerably less stiff than the steel soldier piles. As the lagging deflects, the soil tends to bridge between the stiffer elements resulting in a lower pressure on the lagging. Several previously published methods by others for determining this reduced pressure are summarized and discussed. These methods typically consist of using a portion of the active earth pressure in several different pressure distributions. A simple theoretical model is presented for determination of lateral earth pressures on wood lagging. The model is based on a three-dimensional "silo" shaped sliding wedge analysis. Results of the model are compared with other published methods. The model compares well with these methods which cover the normal spectrum of design situations. In addition, the model can be used to estimate lateral earth pressures outside typical situations.

Jan 1, 2008