Search Documents

By K. Narayan Prabhu, W. D. Griffiths

"Heat transfer during the unidirectional solidification of a cast iron alloy against cast iron chills was investigated using an inverse modelling approach. Chills of thickness 100 mm and 10 mm were used, to simulate gravity die cruiting conditions and the use of chills in sand moulds. In both cases transient heat transfer, measured by the interfacial heat flux and heat transfer coeffieient; declined from initially high values in the first few seconds of solidification, to values about an order of magnitude lower which persisted for the remainder of the experiments. In the case of the thin chill it became saturated with heat until it was no longer in a position to extract further heat from ·the casting. These results were interpreted by studying the resistance to heat transfer from the casting offered by the ·casting-chill interface and the chill itself for example, the thermal resistance of the casting-chill interface can be influenced by the deformation of their respective surfaces and their subsequent relationship.IntroductionDie casting cast iron offers several advantages such as energy savings, higher mould yield, and better surface quality over the sand casting process1 • The process is· environmentally' friendly because of the elimination of the sand. However the design and construction of metallic moulds is expensive and a faulty die design may result in a defective casting: A simulation based process design of die castings would enable die designers and solidification modellings to try better designs of dies on the computer and arrive at a cost effective solution more quickly. This has numerous benefits for the die caster, as he would be able to produce sound castings with very short lead times.The success of a solidification model to predict accurately the thermal history and the location of hot, spots inside a solidifying casting depends to a large extent on the heat transfer data prescribed at the metal/mould interface. Many measurements of the heat transfer coeffident (or the heat flux) between a solidifying aluminum alloy and a chill have shown that the heat transfer coefficient is a function of most of the variables of the casting process2 - 8. However heat transfer studies during the solidification of ferrous alloys are rather limited. The high temperatures involved suggest that the contribution due to radiation heat transfer cannot be neglected."

Jan 1, 2000

By Sebastian Schmuck, Petrico von Schweinichen, Dieter Senk, Mohammad Peymandar

"At Department of Ferrous Metallurgy of the RWTH Aachen University in Germany steels in the system Fe-Mn-C(-Al) are investigated and produced in the framework of the SFB 761 ""steel-ab initio"". A new world of steel grades leads to special challenges regarding the production and recycling at the end-of-life cycle of product. In order to recycle high manganese steel alloys the EAF has to be chosen preferentially. A good slag practice is necessary avoiding loss of manganese content during melting in the EAF. This paper investigates on the reaction kinetics at the interface of slag and steel containing Mn (17-22 wt.-%) and up to 3 wt.-% Al. The effect of changes in the composition of slag and steel on the interfacial reaction kinetics is studied. The thermodynamic software FactSage™ is utilized to calculate the composition of slag and steel at equilibrium.IntroductionTRIP and TWIP steels are highly alloyed steels which show superior strength and ductility when compared to standard carbon steel and stainless steel alloys. These TRIP- and TWIPsteel grades contain typically 15-30 wt.-% manganese, 0-4 wt.-% silicon and aluminum, and up to 1 wt.-% carbon. Steels containing 18-28 wt.-% manganese and 0.7-1.2 wt.-% carbon together with aluminum addition from 3 to 12 wt. -% and without silicon refer to TRIPLEX high manganese steel alloys. These alloys combine high strength at even large ductility [ 1-4]. At the Department of Ferrous Metallurgy (IEHK) of the RWTH Aachen University in Germany, steels in the system Fe-Mn-C(-Al) is under investigation at the collaborative research center, SFB 761 ""Steel-ab initio"". In this project, high manganese alloyed TRIP and TWIP steels are in the focus.The mechanical properties such as high strength and high ductility make this kind of steels perfect candidates for impact absorption applications in auto body such as vehicle doors and bumpers [2, 5]. With increasing the use of TRIP-, TWIP- and TRIPLEX-steels more high manganese steel scraps will be available at the end of life cycle of products, which need to develop the technologies and metallurgical processes to recovery of high manganese steel. A new steel grade brings new challenges in recycling. In order to recycle high manganese steel scraps the electric arc furnaces (EAF) have to be chosen preferentially [1]. Nevertheless it's not easy to prevent the manganese loss during the process in EAF. During the oxygen refining of high manganese molten steel in EAF the manganese content decreases strongly by oxidation and vaporization, which is affected by slag composition, slag properties such as basicity and viscosity, slag weight as well as melt temperature [6-8]."

Jan 1, 2014

By W. Drummond

The cooling of smelter gases by air dilution, adiabatic evaporative cooling and indirect heat exchange is discussed with reference to the process, to the subsequent cleaning of the gas. and to the use of the heat extracted from the gas. The method of reducing the effect of acidic sulphide formation on the corrosive properties of the gas and the dust and the development of surface cleaning mechanisms?are discussed. The development of indirect recuperators using air, water or steam cooling, made possible by the control of surface fouling is traced. The application of the modern Waste Heat Boiler to the new sulphide smelting processes is discussed with respect to the natural and forced circulation concepts. Case histories are presented to illustrate mistakes made with respect to designs produced without recourse to sensitivity analysis and without an appreciation of "worst process? conditions".

Jan 1, 1992

By C. A. Young, J. D. Miller

Adsorption isotherms previously determined by in-situ Fourier transform infrared/internal reflection spectroscopy (FT-IR/IRS) for oleate adsorption at calcite and fluorite surfaces near pH 9 and at various temperatures are compared. Results indicate that, at both mineral surfaces, chemisorption occurs at equilibrium concentrations below approximately l x l0-5 M oleate while calcium dioleate surface precipitation occurs at higher equilibrium oleate concentrations. The extent of chemisorption at the calcite surface is 3 to 5 times less than that at the fluorite surface while the extent of calcium dioleate surface precipitation on calcite is nearly a magnitude larger than that on fluorite. However, for both minerals, surface precipitation decreases with increasing chemisorption. Contact angle measurements and flotation recoveries show the hydrophobicity of fluorite to be greater than that of calcite at each of the temperatures and oleate concentrations studied. Significant differences are noted only in the chemisorption region. Unlike calcite, the hydrophobicity of fluorite was sensitive to the presence of oxygen in the system. Multichannel Laser Raman Spectroscopy (MLRS) showed this behavior was caused by the double-bond reactivity of adjacent chemisorbed oleate molecules and subsequent formation of an epoxide/polyether complex at the fluorite surface. Such a reaction product could not be detected at the calcite surface. These differences in adsorption density, hydrophobicity, and polymerization behavior are discussed in terms of the intrinsic surface properties of the minerals.

Jan 1, 1999

By Sven Eck, Andreas Ludwig, Menghuai Wu

"Phase separation is a frequently occurring phenomenon during solidification accompanied by melt convection, sedimentation or, in the case of two unmixable liquids, a Marangoni driven motion. In order to describe these phase separation phenomena a two-phase volume-averaging model was employed for globular equiaxed solidification of binary alloys and decomposition and solidification of hypermonotectic alloys. The model considers nucleation and growth of equiaxed grains or second phase droplets, motion and sedimentation of grains or droplets, feeding flow and solute transport by diffusion and convection. It allows the prediction of macro segregations and the distributions of grain size or droplet size. Evaluations were made by comparing the numerical predictions with experimental results. For example it is shown that the numerically predicted grain size distribution in a plate casting (Al-4wt%Cu) agrees reasonably well with the experimental analyses.IntroductionModeling of metallurgical processes is a rapidly expanding field and the research activities in the last decades cover a wide range of areas including melt pre-treatment, solidification and subsequent manufacturing routes. Among those activities solidification stands in the central position, because the primary structure of the materials, and even many defects such as porosity, (macro or micro) segregation and inclusions form during solidification. Those primarily formed structures or defects once existing are difficult to be removed or modified by the subsequent material processing.Solidification is a multi-disciplinary field involving thermodynamics, fluid dynamics and solid mechanics, heat and mass transfer, and other disciplinesr1 -31• One of the most challenging problems in solidification modeling is the complex interactions between physical phenomena occurring on different length scales ranging from atomic rearrangement over single crystal-melt interactions to heat extraction, momentum and species transport at the system level. Modeling an industry process on atomic scale is umealistic, even on grain scale (e.g. phase field method) it would need another 40 years to be able to model the exact grain morphology in a casting space envelope of 10x10x10 cm3 [ 4]. Therefore, the realistic models for industry process are based on the solution of the macro transport equations (mass, momentum, enthalpy and species) on system scale. The microscopic phenomena such as thermodynamics, nucleation law, crystal growth kinetics and interactions at the liquid-solid interface are considered with simplified models, which are coupled with the macroscopic transport equations."

Jan 1, 2004

By Carla Lupi

Zinc electrowinning from sulfate solutions is the traditional industrial method to produce SHG zinc. Over the past few years several efforts have been done to improve process efficiency in order to reach high productivity with low energy requirement. The latter aim can be pursued both by means of a hard purification of the electrolyte and reducing the anodic voltage. This work is a comparative study of the results obtained in several previous researches on zinc electrowinning from both sulfate and chloride solutions. Zinc electrowinning tests on industrial sulfate solution have been carried out by using Pb alloy anodes and by adding organic depolarizers such as ethanol, acetic acid or ethylene glycol. Experiments on chloride solutions, obtained by purification of zinc exhausted electrolyte, have been performed by using DSA anodes and by testing the effect of additives such as TEACI and TBAC\. Comparing the best results obtained with the two methods it can be highlighted that a high quality zinc is electrowon in both cases with comparable energy requirements.

Jan 1, 2000

By W. William Culver

James Douglas became known in the nineteenth century for two reasons fundamental to his mining career: (1) his experimental work with copper hydrometallurgy, and (2) his grasp of the idea that the quantity of copper ore matters more than the quality. On the first reason, there is a moment for any technology that’s critically important—when it moves from an area of scientific interest to one that companies are founded on. This paper examines the original 1869 Hunt and Douglas Copper Process in the context of science and engineering as they were in the 1860 and 1870s. It was a “humid” process, developed at Quebec’s Harvey Hill Mine. Chemically, the Hunt and Douglas vat leaching process succeeded, but not the original companies using it. On Douglas’ understanding of ore quality versus quantity, luck had it that the first company to field test the Hunt and Douglas Copper Process was in Chile. The Hunt and Douglas patent made that transition from experimental model to operational plant in 1870 when the Compañia de Minas de la Invernada was organized in Valparaíso. As a joint-stock company, Invernada spread the risk of investing in the revolutionary, but untested, Hunt and Douglas Process. The company brought Douglas to Chile as a consultant in 1871. His experience with hydrometallurgy, combined with what he learned about the copper business while in Chile, set him off on a career in metal mining that both surprised Douglas and made him wealthy.

By Buket Tunçer, Mehmet Buğdaycı, Onuralp Yücel

ZrB2 and TiB2 are one of the most significant metal borides. They are being used in various industrial areas from space technology to nuclear industry owing to their physical properties such as high melting point, high thermal/electrical conductivity and low density. Present study was conducted in two main stages: Self-propagating high-temperature synthesis (SHS) reactions and leaching. ZrO2, TiO2, B2O3 were used as starting material and Mg used as a reductant to produce ZrB2-TiB2 powders via SHS. Therefore, it was aimed to determine production parameters, leaching conditions and comprehensive examination of final product features. The samples were characterized by using chemical analysis (AAS), XRD, XRF and SEM/EDS techniques

Jan 1, 2015

By N. B. Gray, A. E. Guerra, D. E. Morton

"The formation of splash in pyrometallurgical operations that involve the injection of gases into a liquid has been the subject of a number of studies over the last few decades. Given the complexity of the phenomena, there have been some advances in understanding the microscale formation of splash but the ability to accurately predict the amount and character of the splash formed is still in its infancy. First, the macroscale mechanisms for splash formation is very varied. Second, the timescales for splash formation are very small, usually less than 100 milliseconds, making experiments elucidating the formation of splash difficult and costly. Work at the GKW CRC has shown that the microscale mechanism of splash formation is primarily is due to the Kelvin-Helmholtz instability. Substantial progress has been made in understanding the behaviour of large bubbles in effecting splash formation and a simple model has been developed to estimate the behaviour of splash formed from a top submerged lance. Direct numerical computation of splash formation using the GKMAC codes developed at the Centre has been successful in simulating the impact of liquid drops onto a liquid bath.IntroductionInjection of gases into melts is used in the metallurgical industry to promote mixing to ensure acceptable heat and mass transfer rates, conveying solids for alloying, provide efficient contact for gas-melt reactions, and as a reactant. High gas injection rates bring about the formation of splash and slop. Extensive splash formation leads to loss of valuable product, creation of safety hazards, formation of accretion on refractory lining and exhaust ducts, and increased load on dust removal equipment. Many operators and researchers have claimed that splash formation is the limiting factor in many gas injected processes. The problems listed above lead to loss of production and increased maintenance, adding to the cost of processing base metals. Over the last five years, the GKW CRC has been studying the formation of splash from a number of sources. They include the impingment of drops on liquids[ l·2.31, slopping of bath liquidI4.51, breakup of gas bubbles at the liquid-gas interfacel61, shearing of liquids by gases[7·81, and impact of packets of fluids on solidsl81. Theoretically, the extreme deformation of fluid shape and the influence of surface tension makes the simulation of flow resulting from only a drop impacting on a liquid surface a very challenging computational fluid dynamics problem. Recently, we have been successful in simulating the formation of the Rayleigh jet resulting from a drop impact showing the effect of drop Froude number on the shape of the Rayleigh jet."

Jan 1, 1996

By C. H. Bucknam

A review of phase analysis methods used to characterize refractory gold ores is presented. Updating of assay methods using database technology, on-line instrument interfacing and response surface modeling is highlighted. The use of assay results to classify ores for metallurgical purposes is demonstrated.

Jan 1, 1987

By A. Rios

ENAMl's Paipote Smelter commenced operations in 1951. At present, it processes 230,000 tonnes/year of green feed in a conventional smelter, which comprises one reverberatory furnace, two Hoboken, one Peirce-Smith converters and one rotary anode furnace. The feed is composed of 83% copper concentrate and 17% metallic copper precipitates, which results in a feed average grade of 32% of copper content. The final products are 75,000 tonnes/year of copper anodes and 48,000 tonnes/year of sulphuric acid. At present, the plant is undergoing a modernization to expand the smelter capacity to 300,000 tonnes/year of green feed and increase the sulphuric acid production to 100,000 tonnes/year. This will be achieved with the installation of an El Teniente Converter and an expansion in the acid plant. The work began in November 1991 and is scheduled to be in operaton by March 1993. The paper provides an overview of the modernization plans and results achieved to-date.

Jan 1, 1993

By José Luiz Rodrigues Bravo

The production of electrolytic copper with assured quality corresponding to international standards, in a conventional electrorefkery of a custom smelter, is a hard and cautious task, if no advanced technologies for selective control of electrolyte impurities are available. The improper control of the amount of As , Sb and Bi in the anode that enter the tankhouse , attributable either to a bad schedule of concentrate input or to the unavailability of clean concentrates in the international market , as well as the lack of means to maintain the suitable level of these elements in the electrolyte together with other operational circumstances, can result in off-grade copper, as well as affect the starting sheet chemically and physically. This paper presents in a practical way the relationship between the operational conditions and the cathode and starting sheet quality produced at CMSA, covering the period of the last five years of operation, discusses the technologies available in the market for antimony and bismuth removal and compare the results of testwork, achieved in the laboratories of CMSA, using two resins not associated with patented technologies.

Jan 1, 1997

By Zhihong Liu

Monodisperse micron size nickel oxalate particles with rhombohedron morphology were prepared from condensed Ni(OH)2 suspension by a novel gel-sol process proposed by one of the authors. Firstly, condensed nickel hydroxide gel was formed by fast adding 1 mol dm-3 NaOH solution into 0.2 mol dm-3 nickel chloride solution, and then oxalic acid solution with a concentration of 0.25 mol dm-3 was dropped into the gel drop wise through a pump equiped with a pH controller under preset pH value, and in this process, Ni(OH)2 gel was converted gradually into monodisperse nickel oxalate sol. The formation of the nickel oxalate particles was found to proceed through a dissolution-recrystallization mechanism from the nickel hydroxide gel. The product particles exhibited rhombohedron like shape with micron size long axis and sub-micron size short axis. The effects of such factors, as temperature, surfactants, et al, were evaluated experimentally on the particles sizes and morphologies.

Jan 1, 2006

By K. Alibhai

Greek laterites, which generally had nickel concentrations of < 1 %, are amenable to chemical leaching,. although there is considerable variability in the ease of leaching with different ore types. With low grade ores(< 1 % Ni content); >70% of the nickel was leached in columns with a strong selectivity for nickel over iron. Heterotrophic microbially assisted leaching could be a viable alternative to classical hydrometallurgical and/or pyrometallurgical techniques, with a very high recovery (greater than 80% ) being found with some of these mineral microbial interactions. Critic acid was probably the effective chelating agent.

Jan 1, 1991

By L. R. Verney

About 75% of the market economy countries&apos;s supply of cobalt is produced in Central Africa by Zafre and Zambia. Zafre alone accounts for more than 55% and has the resources and capacity to increase output significantly at any time so its dominant position is unlikely to be challenged in the foreseeable future. Other producers from domestic resources are Canada, Australia and South Africa; and Cuba, probably the most important producer outside of the Market Economy countries. Belgium, Norway, France, Japan and Finland produce cobalt from imported materials. While there are "cobalt ores", inMorocco, USA, Canada and the USSR, the mineralisation is complex and cobalt extraction is costly. In ZaPre and Zambia cobalt is a by-product of copper; in Canada, Australia, France, and Cuba it is a by-product of nickel; and in South Africa it is a by-product from the production of Platinum Group Metals. Thus the levels of cobalt production are inevitably related to the production of other primary metals. While some cobalt is produced by predominantly pyrometallurgical methods most of the world&apos;s cobalt is produced hydrometallurgically. The existence of large hydro-electric power plants and the mineralogy of the copper and cobalt concentrates encouraged research and development in Zafre of the recovery of copper and cobalt by electrowinning from sulfate solutions; much pioneering work was carried out, which lead to construction of the two largest copperlcobalt hydrometallurgical plants in the world, at Shituru and Luilu. Similar systems were adopted in Zambia. In Canada high pressure hydrometallurgical processes based on the sulfate system were developed and adopted in Australia, the Philippines, Finland and South Africa. Meanwhile developments in chloride hydrometallurgical extraction of nickel and cobalt lead to its use in the extraction of cobalt in Norway, France and Japan.

Jan 1, 1988

By J. Kevin Cotchen

The results of "submerged arc" electric furnace processing of a variety of materials is discussed with respect to the process and products, including the characteristics of the products (e.g. TCLP or Toxicity Characteristics Leaching Procedure). The materials melted include slags and wastes containing various metal oxides including copper, tin, lead, zinc, chrome, nickel and other associated elements. The findings of these tests are compared to those reported in the literature for other operations treating similar "wastes".

Jan 1, 1992

By Egil Aukrust

"An American Iron and Steel Institute Task Force evaluated developing direct steelmaking technology worldwide to seek a replacement for the coke-oven, blast-furnace, basic-oxygen process technology now in use. To remain internationally competitive it is essential to move away from the traditional series of batch processes towards continuous processing and the associated energy savings which are possible with high technology process control systems. The group identified in-bath smelting of iron ore pellets or fines with coal as the process most sui table for domestic raw materials (including abundant scrap) and called for research to study operation with varying degrees of preheat and prereduction of the ore by the gases generated from the coal and various degrees of combustion of these gases above the melt.A coordinated, 3-year, $27 million, direct steelmaking research program is proposed. Concurrent projects include design, construction, and experimental operation of an in-bath smelting pilot plant; modeling, simulations, and laboratory-scale experiments at universities on slag-phase and metallicphase reactions and interactions; and large-scale heat transfer and reaction rate trials. Also included are modeling studies and pilot plant trials of on-stream decarbonization and desulfurization; application of circulating fluid bed technology to fine ore reduction and hot gas cleanup; and specific heat transfer and fluid flow research projects.IntroductionThe American Iron and Steel Institute (AISI), based on the Task Force studying direct steelmaking, believes strongly that a coordinated program of research on the reduction of domestic raw materials to liquid steel should be undertaken as part of the Steel Initiative program. To specify the steelmaking process for development best suited to the American steel industry and domestic raw materials, it was important to determine the state-of-the-art of direct steelmaking worldwide, both as practiced and under development, and then, by expert analysis of the processes and their potentials, to choose the process most likely to provide a domestic competitive edge."

Jan 1, 1988

By Jorge D. Vier, Raúl B. Rebak, Alicia E. Ares, Natalia S. Zadorozne

Recent worldwide demand has driven nickel and molybdenum prices to record high values. Alloys containing significant amounts of nickel and molybde- num, such as the austenitic and duplex grades, have experienced significant price increases and some spot shortages have resulted in some regions. With low or no nickel content and reasonable molybdenum content, super-ferritic stainless steels are now proving to be the most cost effective corrosion resistant materials. The electrochemical behavior APMT® (Fe–21Cr–5Al–3Mo–0.04C) and 4C54® (Fe–26.5Cr–0.8Mn–0.5Si) super-ferritic stainless steel in NaCl solutions has been studied using open circuit potential measurements, potentiodynamic polarization curves, and electrochemical impedance spectroscopy. The aim is to compare the behavior of these materials with austenitic stainless steel alloy 316 (Fe–18Cr–10Ni– 2.5Mo). The results indicate that the APMT alloy presents a better performance than the AISI 316 stainless steel, while 4C54® does not, especially at anodic potentials. The good behavior of APMT® may be attributed to Al and Mo content in its composition.

Mar 1, 2017

By Michael Somerville, Paul Voigt, Chunlin Chen, Alistair Burrows

To date, many types of primary concentrate have been smelted using the ISASMELT™ technology, with annual smelting of copper concentrate alone exceeding 7 million tonnes. Most of this material could best be described as chalcopyrite concentrate, owing to the predominance of copper attributable to this single mineral. Chalcopyrite concentrates lend themselves readily to smelting with a fayalite slag, and producing a matte containing 55–65 wt% Cu. However, the ISASMELT™ technology also stands ready to meet future copper demand through the treatment of new types of concentrates containing relatively low iron and high silica levels. Various slag systems have been considered for direct-to-blister smelting. They have been evaluated computationally, using the MPE thermodynamic modelling package, and practically, at pilot scale. The lime-silica-iron oxide slag was found to have the lowest slag make, lower dissolved copper and hence lowest copper losses. Based on the outcomes of the modelling and pilot scale testwork a future smelter flowsheet has been defined, comprising a single ISASMELT™ direct-to-blister furnace, an electric slag cleaning furnace, and appropriately designed anode furnaces.

Mar 1, 2017

By Jian-guang Yang, Lei Jie, Si-yao Peng, Jian-ying Yang

A new membrane electrolysis process for bismuth recovery from bismuthinite concentrate was introduced. Under the conditions of temperature 70 degrees C, acidity 3 mol/L, solid liquid ratio 1:4 and 1.1 times stoichiometry sodium chlorate dosage for 1.5 h oxidation leaching, more than 98.5% bismuth can be leached from bismuthinite concentrate. The resultant leach solution was subjected to membrane electrolysis. Under the conditions of NaCl concentration 300 g/L and pH 7 in anolyte, bismuth ions concentration 80 g/L and HCl concentration 3 mol/L in catholyte, heteropole distance 6 cm, temperature 40 degrees C and current density 200 A/m2, a flat deposited bismuth plate can be obtained after 24 h electrolysis, and the bismuth purity was more than 99%. The current efficiency of cathode was 97.88%. Chemical component analysis results showed that the average convert efficiency of the sodium chlorate was 52.77% and the average oxidizing efficiency of chloride ion was 69.78%, and the resultant anolyte generated in anode compartment could be fully reused as oxidant for leaching bismuthinite concentrate again.

Mar 1, 2017