Search Documents

By A. F. Giamei, F. Landis, M. O. Duffy, R. J. Mador

"The directional solidification of complex advanced gas turbine airfoils must be carried out without the nucleation of undesirable grains and with minimal shrinkage. Such problems are typically eliminated by using a number of mold design and process iterations. A more efficient approach is envisioned where a solidification model is generated and utilized to accelerate process development. Towards this end, the directional solidification (DS) of simple geometrical shapes in a crystal grower apparatus has been simulated with MARC finite element nonlinear thermal analyses.The finite element models of cylindrical (2D) and rectangular (3D) cross-section bars in the DS environment are presented. Temperature dependent properties, the impact of latent heat of fusion and a time-dependent radiation boundary condition constitute the more salient features of the MARC models. Solidification zone thermal behavior is predicted during the withdrawal transient for the specific case of nickel based superalloys grown in ceramic shell molds. Comparisons of analytical results with experiments demonstrate notable prediction accuracy. INTRODUCTIONSingle crystal and uni-directional crystal turbine blades require tightly controlled conditions if metallurgically and mechanically acceptable parts are to be produced. Gated blade geometry and process parameters must be precisely determined if incorrect grain structure, orientation and shrinkage are to be avoided. Since purely experimental development programs designed to evaluate these parameters can be excessively costly and time-consuming, an effort combining engineering analysis and verification by experiment has been initiated at Pratt & Whitney. Comparison of analytical predictions and measured data for geometries simpler than a turbine blade, namely cylindrical and rectangular bars, comprised the initial stage of this effort. Subsequent tasks involve modeling geometries of increasing complexity and ultimately the simulation of the directional solidification of the turbine blade, shown schematically in Figure 1. This paper summarizes the results of the initial stage of the effort."

Jan 1, 1986

By Terry Gerritsen

Electrode control systems regulate power by physically positioning electrodes. Due to the size and weight of the electrodes, this is a slow process where power fluctuations of less than a few seconds are not fully corrected. Nickel laterite AC furnaces operating in high voltage, shielded arc mode typically incur frequent power variations of approximately +I- 20% around the power set point. To provide enhanced power control, Hatch has recently supplied, at commercial scale, a thyristor-switched reactance system called an SPLC. The SPLC incorporates predictive control software to operate furnaces at the maximum transformer rating by reducing the large power swings experienced without the SPLC. The resulting higher average power enables higher production, without increasing transformer or power plant capacity. A 60 MW production version of the SPLC has been commissioned on Falconbridge Dominicans's laterite nickel furnace, yielding excellent results with a 3 to I reduction in power fluctuations. Keywords: SPLC, AC Power Supply, Electric Furnace

Jan 1, 2004

By Z. Smieszek, J. Botor, Z. Miczkowski, S. Sobierajski

"From 1978, the direct process for the smelting of chalcocite concentrates in a flash furnace by the Outokumpu method has been applied at the Glogów II copper smelter. The chemical composition of these concentrates make it necessary to control the process very strictly. In this paper, the method for controlling and measuring the main technological parameters of the copper production by flash smelting is being presented. It includes the determination of the chemical composition of the concentrate, its grain structure, the temperature of liquid products of the process, oxygen content in process gases, as well as lead concentration in copper and copper concentration in slag.The main process parameters are determined from the mass and energy balances. The relations between parameters, such as an effect of grain structure of a concentrate on oxygen and oil consumption, and dependence of chemical composition of a concentrate on capacity and products quality are discussed. 1. IntroductionThe Polish copper concentrates, as most concentrates occurring worldwide, contain from 18% to 30% Cu, and less sulphur (7-11%) and iron (2-5%). The main copper-bearing mineral contained in the concentrates is chalcocite, while bornite and chalcopyrite are present in smaller quantities. Moreover, the organic carbon (5-7.5%), arsenic (0.05-0.3%) and lead (1.2-3.0%) are also contained in the concentrates. The gangue consists mainly of silica, aluminosilicates, calcium carbonate and magnesium carbonate. Their proportions make the addition of slag-forming agents unnecessary.The composition of Polish concentrates, especially their low iron content, allows their application in the direct flash smelting process for blister copper production. Low sulphur content is the factor which determines the necessity of oxygen application in this process."

Jan 1, 1989

By M. Furuta, M. Hasimoto, Y. Komoda, K. Haiki

"Tamano Smelter & Refinery started its operation in 1972 with high current density electrolysis (350Nm2 of maximum) applying PRC technology. After the start up, four times of expansion have been done, the cathode production capacity has increased from- 84,000 t/y to 191,000 t/y. However, recent refining technology with permanent stainless steel cathode enabled to increase current density up to 300 Nm2 or more without PRC method. In order to increase current density more than 350 A/m2 , experimental work using commercial size cell has been carried out at several conditions, such as current density, PRC conditions, electrolyte composition and electrode condition. As a result, it was found that high quality (LME A grade) cathode can be produced at such a high current density as 405 A/m2•IntroductionWhen considering the production increase of electrolytic copper, what becomes important is the improvement of productivity per unit of production facility. Conventionally, production had been expanded by increasing the number of cells but a huge investment required for this had a influence to the business profitability. Because of this, increase of current density, which is one of the methods to improve unit productivity, 'was expected and this method at the same time has another advantage of shortening the retention time of copper and other precious metals in the cells. At present, the average current density at Tamano during full capacity production is around 350 A/m2 and this used to be the limit throughout the world (1)."

Jan 1, 2000

By B. S. Terry

Experiments have been conducted to assess the feasibility of capturing bearing emissions arsenic with CaO during the roasting of enargite (Cu3AsS4). Enargite/CaO mixtures have been heat treated in air, nitrogen or oxygen for various times and the products of reaction analysed by X-ray diffraction and cleaned analysis. The results show that substantial capture of arsenic can be achieved via the formation of calcium arsenates and/or calcium arsenides. In addition significant capture of sulphur is achieved by the formation of calcium sulphate andlor sulphide. Complete conversion to copper sulphide with total removal of arsenic can be achieved within 30 minutes at 700°C. Further heat treatment in air or oxygen leads to the formation of copper oxide and copper oxysulphate. Without optimisation of reaction conditions, it has proved possible to achieve retention of in excess of 85% of the arsenic content of enargite in the form of calcium arsenates.

Jan 1, 1994

By Deming Wang, R. A. Overfelt

"The oscillating cup viscometer has become a dominant technique to measure the viscosities of high temperature molten metals. Unfortunately, the viscosity estimation model from the observed logarithmic decrement and period of the oscillation is very complicated. There are still large discrepancies of viscosity estimation values between using different measurement facilities and using different viscosity estimation models for a same molten metal. The purpose of the paper is to evaluate the accuracy of an oscillating cup viscometer in Auburn University. Two well known viscosity estimation models, Roscoe's and Torklep's equations, are compared and discussed. The theoretical literature for the fluid flow inside an oscillating cup is reviewed and a more accurate working equation for the Auburn oscillating cup viscometer is developed. Some design parameters of the oscillating cup viscometer, which directly affect the accuracy of viscosity estimation by using the working equation, are discussed. In addition, applications and experimental measuring data are presented in the paper for several different commercial alloys, such as aluminum alloys: A319, A356 and A201, nickel-base super alloys: In713 and In718, and casting irons, C40 Gray Iron and Ductile Iron.1 IntroductionThe oscillating cup viscometer is the most important and has been most frequently used in viscosity measurement for high temperature liquids [1-4]. The principal advantages of this technique over others are its mechanical simplicity and the ability to measure the time period and amplitude decay with great precision. In the viscometer, a high temperature liquid (such as a molten metal) is contained within a crucible suspended by a wire to form a torsional pendulum, which induces torsional oscillation motion. This motion is damped primarily by viscous dissipation within the viscous liquid inside the cup. The viscosity of the liquid can be calculated by an analytical or numerical solution ofthe equations of motion of the oscillating cup system."

Jan 1, 2001

By Valery Kaplan

Sulfur emission in the form of SO2 in flue gases is one of the most serious atmospheric pollutants associated with coal combustion and non-ferrous metals production. The carbonate eutectic method for removing SO2 from flue gases at 723–923 K was initially proposed in the 1970s but despite its great efficiency (SO2 concentration in the flue gas after purification reached 0.003 volume %), it could not be implemented by industry due to the complexity of the carbonate melt regeneration stage. Earlier we proposed a method suited to coal-firing power stations where the melt was regenerated using CO as a reducing agent. However, most metallurgical plants do not use coal and therefore lack a large source of CO. Here we propose a method for removing sulfur from the carbonate eutectic melt by purging it with natural gas or a natural gas/air mixture, which are available in the vast majority of metallurgical plants. This reaction leads to the reduction of sulfate to H2S gas that leaves the melt. The experiments we conducted show that nearly complete sulfur removal from the melt is possible at 823 K and that the reaction rate is sufficiently high for a large scale process. One can foresee that this carbonate melt-based SO2 removal technique may become a practical and economically attractive method for limiting sulfur emission to the atmosphere from non-ferrous metallurgical processing plants.

By Roberto Parra

The classic criteria of the preparation of the charge for the smelting of copper concentrates in a flash furnace considers the mass and energy balance from the chemical and mineralogy composition of the concentrates. The operation parameters fixed with this method don't assure the stability of the operation and the critical problems of the slag quality and dust formation occurs very often. This paper presents the results of a laboratory test that allows the predicition of the behavior of concentrates blends in the view of the minimization of the dust formation and the magnetite control in the slag. The combustion of different copper concentrates and blends were done in a drop tube furnace. The results show that the magnetite and dust formation don't have a linear behavior with the weight proportion of the blend and some optimal blends of 2 or 3 types of concentrates can be identified. From the reasonable hypothesis that the qualitative behavior of blends in the drop tube represents the real behavior in the burner, the preparation of the charge with this approach could help to solve those operational problems.

Jan 1, 2003

By R Bartlett

Process engineering-science originally developed for percolation leaching of ore in heaps is extended to the decontamination of unsaturated soil, either in situ or after excavation and emplacement as a soil heap on an impervious pad. Phenomena considered include: soil matrix porosity and permeability; percolating solution retention, capillarity and flow; washing sweep efficiency; optimum solution application rates during leaching; soil agglomeration to improve soil permeability and soluble contaminant transport by diffusion in soil agglomerates. Practical aspects briefly discussed include leach pad construction, solution distribution and recovery from the soil, and solution containment.

Jan 1, 1994

By S. Z. El-Tawil, K. A. El-Barawy, M. B. Morsi, M. M. Nasr, Z. I. Zaki

"Tue sulphatization of zinc concentrate produced from heated zinc concentrate of Um Ghieg area, eastern desert by ammonium sulphate as sulphatizing agent is carried out at different conditions to achieve the appreciable formation of soluble sulphates. The maximum zinc recovery as soluble sulphate equfils to 95% upon using 1.5 stoichiometry ammonium sulphate at 600 °C for one hour. Tue obtained leached zinc sulphate solution is subjected· to purification process to prepare high pure zinc metal and zmc compounds such as pure zinc sulphate, zinc caibonate and zinc oxide. The products obtained are analyzed chemically and identified by X-ray analysisTue mechanism and kinetics of the sulphatization process of zinc concentrate are considered where the activation energy is calculated and equals to 33.3 K.J.mol""1 A process flowsheet for the overall sulphatization process of zinc concentrate by ammonium sulphate is proposed.IntroductionConsiderable reserves of zinc ores are present in Um Ghieg area eastern desert, Egypt. The possibility of extraction zinc from these ores and preparing its valuable compounds by choosing a more feasible technology become of vital importance. An attention is focused on the sulphatizing roasting processes (1-9) to achieve the appreciable formation of soluble sulphates. Previous publications are reported in our division by El. Tawil and others (10-16) using ammonium sulphate as sulphatizing agent for the successful treatment of nonferrous bearing materials.Therefore, the present work aims to study the different factors affecting the sulphatizing roasting process of local zinc coocentrate by anunonium sulphate to extract completely zinc and preparing its main compounds. Tue mechanism and kinetics of the different chemical reactloos that 1ake place in the process are considered."

Jan 1, 2000

By John A. Mavrogenes

Reflected light microscopy and electron microprobe techniques were used to determine the mineralogy, phase percentages, grain sizes, and textures of Co-Ni-rich mattes. The mattes were produced by submerged bath smelting at the University of Missouri-Rolla Pyrometallurgical Center of a flotation concentrate with 4.S% Co and 5.1% Ni that was prepared at the United States Bureau of Mines Rolla Research Center by flotation up-grading of the cobalt and nickel content of a copper concentrate from the Magmont mine, Viburnum Trend, Southeast Missouri. Nine distinct phases were distinguished in the matte samples, and three of these contain cobalt and nickel. The phases that were free from cobalt and nickel are bornite, chalcocite, pyrrhotite, magnetite, metallic copper, and galena. Submerged bath smelting serves to segregate the cobalt and nickel into phases that can subsequently be recovered by flotation. These phases are: shandite (Ni3PbZSZ)' cobaltpentlandite ((Co,Ni,Fe)9SS)' and Co-bearing Fe-rich sphalerite ((Zn,Fe,Co)S). Most of the cobalt occurs in cobaltpentlandite, but some is present in sphalerite. High total air conditions during smelting favor the development and segregation of cobalt into cobaltpentlandite. Nickel occurs in cobaltpentlandite and shandite. Shandite contains lead, a deleterious constituent in the smelting of cobalt and nickel.

Jan 1, 1989

By Xiang-ning Meng, Miao-yong Zhu

"A three-dimensional finite-element heat-transfer model is conducted to predict temperature of hot copper plate in a slab continuous casting mold and the effect of casting speed on temperature difference between copper plate and solidifying shell is simulated in combination with process data. The results show that centre temperature of hot copper surface at casting speed 1.8 m·min-1 and 2.0 m·min-1 are higher than that of 1.6 m·min-1 casting speed 4.7-5.2 °C and 11.2-12.2 °C respectively and temperature is not increased linearly with casting speed. Temperature difference in meniscus between mold and shell is influenced obviously by casting speed and increased 4.0- 6.0 °C with increment of casting speed 0.2 m·min-1• Fluctuation of temperature difference in meniscus is a main reason to deteriorate casting quality as increasing casting speed.IntroductionIn conventional continuous casting of steel, a large amount of sensible and latent heat of molten steel dissipates in primary cooling zone and mold becomes a critical component of caster to govern steel quality, meanwhile, thermal load on mold is increased constantly and environment is also more abominable since high productivity and quality are required and high-effective technologies are applied. So, an in-depth understanding of thermal behavior of mold at high casting speed is essential to design cooling structure and maintain casting stability. Many studies have been carried out to shed light on thermal behavior in mold. Chow et al. [l] applied a mathematical model to heat transfer in billet mold at a high casting speed to give a new taper in order to minimize mold-strand interaction. Thomas et al. [2] researched relation between mold geometry and temperature distribution based on a finite-element heat-transfer model. Lu et al. [3] indicated that slab mold temperature are mainly affected by thickness of copper plate and nickel layer by a heat transfer model. Samarasekera et al. [4, 5] researched temperature of copper plates for both billet and slab molds and effect of a large number of factors ranging from water quality to casting speed. Park and Thomas et al. [6, 7] developed a finite-element thermal-stress model to determine temperature and thermal distortion and stress in both thin and slab molds and O'Connor et al. [8] applied an elastic-plastic-creep finite-element model in a funnel shaped mold to achieve same goals. Cicutti et al. [9] evaluated heat transfer and temperature fluctuation in a slab mold and proposed an expression to predict global heat flux as a function of process parameters and an index to quantify thermal instability. All mentioned above shown that thermal behavior is not only important to casting stability, it is also premise to further understand mechanical behavior in mold."

Jan 1, 2011

By J. P. Gu, C. Beckermann

"Melt convection and macrosegregation in casting of a large steel ingot is numerically simulated. The simulation is based on a previously developed model for multicomponent steel solidification with melt convection, and involves the solution of fully coupled conservation equations for the transport phenomena in the liquid, mush, and solid. Heat transfer in the mold and insulation materials, as well as the formation of a shrinkage cavity at the top are taken into account. The numerical results show the evolution of the temperature, melt velocity, and species concentration fields during solidification. The predicted variation of the macrosegregation of carbon and sulfur along the vertical centerline is compared with measurements from an industrial steel ingot that was sectioned and analyzed. Although generally good agreement is obtained, the neglect of sedimentation of free equiaxed grains prevents the prediction of the zone of negative macrosegregation observed in the lower part of the ingot. It is also shown that the inclusion of the shrinkage cavity at the top is important in obtaining good agreement between the predictions and measurements.IntroductionMacrosegregation in large steel ingots is one of the most well-known and now classical problems in the field of solidification and casting [1]. Commonly found macrosegregation patterns in steel ingots are a positively segregated zone at the top, negative segregation near the bottom in the equiaxed zone, inverse segregation near the ingot surface, V-segregates along the centerline, and A-segregates in the columnar zone [2, 3]. It is well established that the macroscopic transport of species leading to macrosegregation can occur by a variety of mechanisms, including thermally and solutally driven natural convection of the melt in the mushy zone, flow due to solidification contraction, and the sedimentation of free equiaxed crystals. Fredriksson and coworkers [ 4,5] provide recent overviews of the solidification transport phenomena and macrosegregation in ingot casting."

Jan 1, 1999

By James W. Evans, Dong Xu, Jr. Jones

A physical (water) model based on particle image velocimetry (PIV) has been constructed at UC Berkeley. The PIV technique enables the use of water modeling to quantitatively characterize the fluid flow behavior in the mold during the continuous casting of steel, in a whole field sense, i.e., section by section. A method to obtain e\e time-averagevelocity (TA V) vector maps was developed by averaging 40 instant aneous vectc -r plots revealing the time average features of the flow. Another benefit of TAV vector maps is the ability to compare with present mathematical models, which are mostly based on the time-average technique. Bifurcated submerged entry nozzles (SEN) with ports inclined at various angles to the horizontal were used in the modeling to study their effects on the flow inside the caster. Argon was also introduced into the model to simulate the influence of argon injection on the metal delivery from the tundish into the caster. The bubble sizes and distribution (in specific sections) of argon were characterized, at the same time, by the imaging system of the PIV. This will allow for validation of current mathematical models that were developed to simulate argon injection in casters. Comparison with results calculated by the commercial finite element package FIDAP is also presented.

Jan 1, 1998

By Jasper Kwong

The recycling of MgO-C refractories as a slag conditioner in EAF (electrical arc furnace) foaming slags have been evaluated by the Albany Research Center. The amount of MgO in the slags is critical for the foaming quality. Good foaming slags provide the benefits of high energy efficiency and low refractory consumption and require saturation with MgO. A computer model predicting the chemistry of MgO saturated foaming slags was designed to predict suitable amounts of MgO additives from MgO-C spent refractories. This model can also help to reduce the amount of slags and to improve the economics of producing steel. The implementation of this recycling program is underway at steel plants and the experience of recycling spent refractories will be discussed.

Jan 1, 2002

By Patricia A. Wells

In the remelting of scrap, the ultimate goal is to produce clean aluminum while minimizing metal losses. Recently, it has become more difficult to make significant recovery improvements in Reynolds' Reclamation Plants since metal recoveries were nearing the theoretical maximum. In an effort to gain a better understanding of the factors impacting Reynolds remelting process, a series of experiments using a Taguchi-type design was performed. Specifically, the critical variables and interactions affecting metal recovery of shredded, delacquered Used Beverage Containers (UBC) melted in a side-well reverbatory furnace were examined. This furnace was equipped with plunger-style puddlers and metal circulation. Both delacquecing and melting processes operated continuously with downtime only for necessary mechanical repairs. The experimental design consisted of an orthogonal array with eight trials, each using nominal 500;000 lb shred charge volumes. Final recovery results included molten output and metal easily recovered from dross generated during the test.

Jan 1, 1995

By Nagy El-Kaddah

"One of the emerging technologies for the production of ultra-clean metals is electromagnetic filtration. The theory and the mechanism of electromagnetic separation of inclusions from molten metal are briefly reviewed along with basic electromagnetic separation systems. This paper focuses on inclusion removal in the induced current separators, with specific reference to a new separator developed at the University of Alabama. A simple analytical model is presented for the analysis of particle separation in such a system. The role of the applied magnetic field on inclusion removal will be discussed. It is shown that particle velocity increases exponentially with increasing magnetic field strength. At moderate field strengths, the velocity of 50 to 100 u. inclusions· are an order of magnitude larger than those achieved by buoyancy. The separator developed at the University of Alabama is described together with experimental results of laboratory and large scale experiments on purification of molten aluminum. These results demonstrate the capability of the system for producing super-clean metals.IntroductionThe nature of extraction, refining and processing of metals is such that oxides and other non-metallic particles will always be present. This is due to the highly reactive nature of metals with oxygen and other non-metallic elements. The presence of these type inclusions in metals, even in minute amounts, can seriously flaw the reliability and performance of the final product. They not only reduce the strength and the stiffness of the metal/1/, they are the reason behind many of manufacturing defects such as porosity in castings, surface and internal cracks in continuously cast ingots and rolled products, etc., which act to cause premature failure of manufactured parts. In fact, for critical applications such as turbine blades, there is virtually no tolerance for inclusions above ten microns in size /2/. Therefore, removal of inclusions from the liquid metal is an essential processing step.The demand for cleaner metals has brought major changes in the technology and practice of metal refining and casting. Inclusion removal from the melt is currently achieved by passing the melt through a series of melt treatment systems, including induction stirring furnaces, argon-stirred ladle, and ceramic foam and deep-bed filters /3,4/. These systems are generally capable of removing all inclusion particles above 50 microns in diameter, which meets current cleanliness requirements for most applications. However, they may not be able to meet the projected cleanliness levels for critical applications due to kinetic and operational limitations of these systems in removing smaller particles /5/."

Jan 1, 1996

By Liu Wei-feng

Base on the thermodynamic calculation of vapor pressure of lead, antimony and arsenic at high temperature, the possibility of separating lead, antimony and arsenic in different temperature was analyzed ,and the practice of producing qualified antimony white from lead-antimony alloy by direct blowing was introduced in detail in this paper. The blast furnace reduction smelting was brief introduced firstly, and then alkaline refining was applied to removing arsenic from lead-antimony alloy that contains As1%,Sb39%,Pb58%,the arsenic in the treated lead-antimony alloy could decrease to 0.009% by that method. The antimony white containing Sb2O3 99.5% could be produced by air blowing in the special furnace at 650? from the treated lead-antimony alloy. And the electrolytic lead could be achieved by electrolysis from the lead-rich alloy which contained 83% lead.With high-grade product being obtained the process was shortened. The technology has been applied successfully many years in Guangxi, China.

Jan 1, 2009

By Warren J. Bruckard, Mark I. Pownceby, Sazzad Ahmad, M. Akbar Rhamdhani

Rutile is the preferred feedstock for producing high-grade TiO2 pigment but due to decreasing resources, alternative materials such as ilmenite is now used to produce a synthetic rutile (SR) feedstock. This requires removal of impurities (e.g. Fe, Mg, Mn) which, for a primary ilmenite is straightforward process. Processing of weathered ilmenite however, is complex, especially when chrome-bearing impurities are present since minor chromium downgrades the SR market value as it imparts color to the final TiO2 pigment, Chrome-bearing spinels are a problem in weathered ilmenites from the Murray Basin, Australia as their physical and chemical properties overlap with ilmenite making separation difficult. In this paper, different sulfidation process routes for weathered ilmenites are analyzed for their applicability to Murray Basin deposits as a mean of remove chrome spinel impurities. Thermodynamic and experimental studies indicated that selective sulfidation of chrome-bearing spinel can be achieved under controlled pO2 and pS2 processing conditions thereby making them amenable to separation.

Jan 1, 2015

By Jinjing Dua, Jun Zhua, Kuiren Liub, Bin Wang, Xiaolei Wua

V-Ti-Fe as hydrogen storage alloy was prepared by reducing metal oxides with a metallothermic reduction method. The deoxidation process of the V-Ti-Fe alloy was performed by electro-deoxidation and vacuum induction melting method, respectively. The results showed that the content of oxygen impurity can be controlled at about 0.2wt% after electrolyzing for 240min. Both the maximum values of hydrogen absorption capacity and the effective hydrogen desorption capacity are 2.65wt% and 1.01wt%, respectively. The deoxidization effect of vacuum induction melting process is more remarkable, with Ce as the reducing agent. It is found that Ce addition is beneficial for reducing the componential segregation, promoting the hydrogen absorption activation of V-Ti-Fe alloy. When m(Ce)/m(alloy) is up to 5%, the oxygen content has been reduced to 0.05wt% and the maximum hydrogen absorption capacity and the effective hydrogen desorption capacity are up to 3.36wt% and 1.85wt%, respectively.

Jan 1, 2015