Search Documents

By A. H. Castillejos E., F. A. Acosta G.

Filtration is widely used as a terminal refining step for metals, particularly for the casting of aluminum alloys, but still more knowledge is required to understand how several factors affect the efficiency of removal of inclusions. In this study, both, initial and long term filtration efficiencies of a ceramic foam filter have been obtained from the computed trajectories of solid particles suspended in molten aluminum. The complex structure of the foam filters is represented by a unit cell which is formed by a pair of pores with average dimensions. The fluid flow field was determined from the numerical solution of the Navier-Stokes equation, and periodic fully developed flow was assumed at the inlet of the calculation domain, as a boundary condition. This flow field corresponds to laminar flow as that found in ceramic filters operating under normal conditions. Computed initial filtration efficiencies showed that filtration efficiency decreases sharply with fluid velocity for particles larger than 30 µm, but smaller particles are better trapped at higher fluid velocities. Finally, it was found that long term filtration efficiency for particles of 8 µm decreased with time, in spite that perfect particle-wall attachment was assumed. Filter aging was considered in this study, and it was found that the distorted flow field, around the already trapped small inclusions prevented further collection.

Jan 1, 1999

By J. D. Scott

The counter-current jarosite acid wash circuit presently in operation in the zinc plant produces a combined jarosite plus Pb/Ag residue which is discarded. Extensive pilot-scale testwork, and some past in-plant operational experience, has shown that the zinc plant can be easily reconfigured to produce two residues during periods of high silver feeds and/or prices. Plant.optimized circuit configurations are available for silver recovery to a Pb/Ag residue and are in use for the prevention of Pb/Ag-jarosite formation in both the neutral and high-acid leaching circuits. Silver in the zinc plant undergoes several changes in state as it proceeds through these circuits. The roaster calcine is ~3:1 silver sulfate: silver metal, with metallic silver mainly as micro-Inclusions In an aluminosilicate phase. In neutral leach residue, the majority is as silver sulfide or Pb/Ag/Zn-sulfide coatings on unroasted sphalerite grains, with minor Pb/Ag-jarosite and some residual metallic silver in unreacted alumina-silicate grains. In high-acid leach residue, silver occurs as Se-rich silver sulfide particles in sulfur/jarosite ball aggregates, as silver sulfate impregnations in silica-gel masses and in solid solution in Pb/K/Zn~jarosite. Silver concentrations in solution range from 20 to 60 ppb.

Jan 1, 1990

By D. Mishra

Electric arc furnace dust (EAFD) generated during the recycling of steel- scrap is classified as a hazardous waste for landfilling. This is because it contains leachable heavy metals such as zinc, lead,... Recovery of these metals could result in both resources conservation and resolving waste disposal problems. A study of the thermal reduction of a sample of EAFD was carried out in an inert gas atmosphere using coke as a reducing agent. Preferential volatilization of zinc and lead was achieved during the reduction process at about 800 "C. More than 96 % of both zinc and lead were removed from the dust and were recovered in the condensates. The treatment residue was essentially composed of iron oxides and almost free from heavy metals.

Jan 1, 2002

By Kexin Jiao, Zhijia Zhang, Jianliang Zhang, Zhengjian Liu

Carburization behavior of molten iron in blast furnace is an essential part of BF long campaign technology. Maintaining carbon content stable is an important prerequisite to ensure the high production of the blast furnace. In this paper, the important aspects of the research progress which mainly including the study of iron carburization at the upper and the lower parts of the blast furnace was reviewed. Indirect carburizing is the main way at the top of the blast furnace. The content of carbon in metallic iron increases with the reducibility of iron ore improved. The thermodynamics and kinetics conditions are good for carburization reaction to take place at the bottom of the blast furnace. Carbon content of molten iron increased by coke carburizing. Meanwhile, the drawbacks of the existing literature on iron carburization behavior were analyzed and new research directions of iron carburization were proposed in the future.

Jan 1, 2015

By Cong Wang, Kexin Jiao, Yongan Zhao, Haibin Zuo, Jianliang Zhang

Traditional refractory materials for blast furnace hearth lining are mainly composed of carbon bricks and the ceramic cup. However, these materials can’t meet the demands for long service life design of blast furnaces. In this paper, a new refractory called carbon composite brick (CCB) was introduced, which combined the advantages of carbon bricks and the ceramic cup. In this case, the resistance of the CCB against corrosion was equal to the ceramic cup and the thermal conductivity of the CCB was equal to carbon bricks. From the results of more than 20 blast furnaces, the CCB could be well used in small blast furnaces and large blast furnaces. In the bad condition of low grade burden and high smelting intensity, the CCB gave full play to the role of cooling system, and effectively resisted the erosion of hot metal to improve the service life of blast furnaces.

Jan 1, 2015

By Gervais Soucy, François Quesnel, Pierre Hovington, Wen Zhu, Karim Zaghib, Jocelyn Veilleux

The properties of lithium titanates anodes in Li-ion batteries are highly dependent on their secondary constituents. While their main phase is usually constituted of Li4Ti5O12, significant quantity of lithium titanates compounds of various stoichiometry are often present, due to either the processing, usage or aging of the material. These may go underreported, as many of these spectrums overlap or display low signal in X-ray diffraction (XRD). Samples of nanosized lithium titanates synthetized by inductive plasma were characterized by XRD and scanning electron microscopy (SEM), as they provide a regular yet typical crystallite size and shape including multiple phases. A Rietveld refinement was developed to extract the composition of these samples. Mass balance through further annealing and differential scanning calorimetry (DSC) enthalpy measurements from phase transformations were also used as identification and validation techniques.

Jan 1, 2015

By K. Morsi, S. K. Kassegne, A. El-Desouky, K. S. Moon

"Current Activated Tip-based Sintering (CATS) is a new process for the powder-based fabrication of macro, micro and possibly nano-scale features and shapes. This new and unique process enables selective sintering of powders by localizing electrically activated sintering conditions through a stationary or moving electrically conducting tip. We present preliminary experimental results on the effect of tip size in the CA TS process as well as the effect of initial powder particle size on the sintering behavior of nickel powder.IntroductionSpark Plasma Sintering (SPS) has been the center of attention of numerous researchers due its noticeable advantages over conventional sintering techniques such as rapid heating rates, lower sintering temperature and shorter holding times. Research on SPS has been applied on a wide variety of materials such as pure metals [ 1], ceramics [2], composites [3], nano-materials [ 4], biomaterials [ 5], shape memory alloys [ 6] and many other material systems. However, it has been mostly limited to bulk materials with simple shapes with a few exceptions ofresearch efforts where the effect of electric current was combined with metal forming processes such as spark plasma extrusion [7,8] and electric rolling of powders[9]. In this paper a novel process (Current-Activated Tip-Based Sintering (CATS)) is discussed where electric current and pressure are applied simultaneously through a small conducting tip (stationary or moving) over a conducting powder compact. This process has the potential advantages of sintering complex geometries with minimum energy requirements as unconventionally high current densities can be achieved due to the small contact area between the tip and the powder compact. Furthermore, by controlling the tip size, it can be possible to sinter features on the macro-, micro- and even nanoscales."

Jan 1, 2011

By Harry Littleton, Jr. Scarber, Wanliang Sun

"The Lost Foam Casting (LFC) process is relatively immature when compared to other casting processes. To make the process more robust, computer modeling is needed to reduce lead times and casting defects. In this study, metal filling of lost foam aluminum castings was visualized using state-of-art real time X-Ray technology. Metal filling of the lost foam casting was simulated using a commercial software package. The result of the computer simulation was compared with the results of the real time X-Ray visualization. Some of the computer simulation results agreed with the real time X-Ray visualization, but some did not. Based on other studies using real time X-Ray technology, new input variables, such as foam density variations, were developed for the computer modeling. With the new variables, modeling of the lost foam casting process becomes more realistic. IntroductionMold filling of the Lost Foam Casting (LFC) process is an important step toward making a quality part. In the LFC process, molten metal is poured against a refractory coated foam pattern surrounded by dry sand. At the pouring temperature of aluminum, the foam pattern is decomposed into 30% (wt) gaseous and 70% (wt) liquid foam pyrolysis products. Existence of the gaseous foam decomposition products significantly increases the back pressure on the metal stream compared with the conventional open cavity sand mold. Entrapment of the liquid pyrolysis products during the metal filling generates many casting defects, such as internal pores, fold and blisters. Existence of these casting defects sometimes seriously degrades the quality of the components manufactured by the LFC process. Understanding and controlling the metal filling of the LFC process will certainly make this process more robust."

Jan 1, 2004

By Jingwei Lou, Bing Li, Suzhen Li, Miao Shen, Jianguo Yu

"As a main impurity in primary lithium metal, magnesium is difficult to remove because of the very close relative volatility of the two metals. Electrochemical refining provides a possibility to completely remove Mg in the LiCl-KCl melt prior to Li reduction. MgCl2 reduction processes in LiCl-KCl- MgCl2 melt were investigated by cyclic voltammetry (CV), square wave voltammetry (SWV), chronoamperometry and chronopotentiometry. Then potentiostatic electrolysis was carried out and Mg (II) ion was reduced onto a liquid lead cathode from the LiCl-KCl-MgCl2 melt at the Mg deposition potential. The results show that Mg ( II ) is reduced in one step with two-electron transfer. The reduction potential of Mg ( II ) was well defined. The reduction of Mg( II) results in Li ( I ) underpotential deposition at 0.2V more negative potential than that of Mg( II) reduction. Therefore, in order to prevent Li ( I ) from codeposition with Mg, accurately controlling Mg ( II) reduction potential during the potentiostatic electrolysis was necessary. Ninety three to 99 % removal rate of MgCl2 was achieved after 8-12 h electrolysis when liquid lead was used as cathode.IntroductionMetallic Li has been widely used in batteries, light weight alloys and in fusion reactors because of its excellent properties. Currently, the only way in industry to produce metallic Li is by electrowinning from molten LiCl-KCl at about 450 °C [l-5]. LiCl-KCl is the only electrolyte used, because they presents a lower eutectic temperature and KCl shows a slightly higher theoretical decomposition voltage than LiCl, as shown in Table l .The produced metallic Li generally contains 1-2 wt% impurities including Na, K, Al, Ca, Mg, Si, etc. [6l, which are derived from the corresponding metal chloride compounds or metal oxide compounds existing in the LiCl and/or KCl raw materials. These impurities have to be removed by subsequent vacuum distillation at high temperatures to meet the requirements for metal Li purity in the final products. Separation of Mg from Li by vacuum distillation is difficult because their relative volatilities are very close, as shown in Table 2."

Jan 1, 2011

By Caisa Samuelsson

Experimental studies in laboratory-scale equipment have been carried out to study the vaporisation from dust generated during the copper converting process. In the present work the vaporisation of Zn, Pb, As, Sb, and Bi from a dust collected in the electrostatic precipitator after the copper converter were studied. The results show that Pb, Bi and As were vaporised to a high degree from the dust at a temperature above 900°C in a gas containing N2, SO2 and a small amount of H2. The vaporisation was high for these elements also in a gas containing N2, SO2 and 02 at temperatures above 1120°C. In an earlier study, thermodynamic calculations showed that it is possible to selectively condense metals at high temperature' in a gas atmosphere generated during a copper converting process. The present study was carried out to verify the thermodynamic model. The results indicate that it should be possible for a selective condensation of Zn at high temperature. The temperature required for a selective condensation of Zn is dependent upon the gas atmosphere, e.g., the oxygen potential.

Jan 1, 1998

By J. R. Sarazin

Density driven convection during solidification has been recognized for some time to result in macrosegregation particularly when lower density alloying elements are rejected into the interdendritic liquid. The resulting segregates are commonly referred to as channels, freckles or A-segregates. Buoyancy driven convection leading to channel formation has been examined in three model systems possessing somewhat different materials parameters. They are the Pb-Sn eutectic system, the transparent aqueous-salt NH C1-H 0 4 2 eutectic system and the transparent organic succinonitrile-ethanol monotectic system. Convection in these systems is controlled by a balance of buoyant and viscous forces, which are strong functions of composition and temperature. Composition, temperature and flow velocity were measured and elimination of channels through heavier ternary additions is discussed.

Jan 1, 1991

By Chuanfu Zhang, Liwei Liang, Yanxin Wu, Jinliang Wang

"According to the reaction shaft operation characteristics during the flash smelting process, 15 groups of slag samples containing high Fe3O4 were prepared by some chemical reagents, and then the slag viscosities were measured using a RTW-10 type synthetic test instrument for melt physical property by the rotating cylinder method. The effects of Fe/SiO2 ratio (mFe/mSiO2), Fe3O4 content (wFe3O4), Cu2o), MgO content (WMgO) and Cao content (wCaO) on the slag viscosity were also studied. Results show that slag viscosity is decreased with the increase of temperature, mFe/mSiO2, wCu2o, wMgO and wCao, and with the decrease of wFe3O4, under the range of slag contents: mFe/mSiO2 1.36~1.78, wFe3O4 17.83%~21.18%, wCu2o 3.51%~8.34%m wNgI 2.21%~6.57%m w/caI 6.22%~9.387% and temperature range if 1250 o/c~1450 oC. Only wFe3O4m and w/caO have great influence on the slag viscosity when temperatures as high as 1400 oC. Only wFe3O4 and wCaO have great influence on the slag viscosity when temperatures as high as 1400 oC or so. To form a freeze slag with higher viscosity inside the reaction shaft, wFe3O4 should be more than 20% and wCaO should be less then 6%.IntroductionSince its appearance in 1949, Outokumpu flash smelting technology has making continuous innovation and has become the most competitive intensified smelting technology [1], widely considered to be the standard clean smelting process [2]. At present, flash smelting technology is adopted to newly build or reconstruct most of the world's copper or nickel smelting enterprise [3]. Reaction shaft is the most important part of the flash smelting furnace. During the flash smelting process, reaction shaft must be able to withstand the following harsh conditions at the same time: 1) high temperature varying from 1400 °C to 1500 °C. 2) strong oxidative atmosphere containing 50% - 80% oxygen. 3) solid particles and melt with speed up to l00 m/s. 4) high acidic or basic slag with strong chemical corrosiveness. 5) smelting gas containing 50% - 80% SO2. 6) matte with strong dissolution."

Jan 1, 2012

By R. Burkhard

Recovery of metals from complex mixed wastes is a challenging task of modem material and waste management strategies. Thermal methods are an important tool in this respect. Plasma turned out to be particularly useful for treatment of complex or toxic wastes and residuals. In order to study plasma processes at reasonable costs, a pilot plasma plant has been used and wastes like ~pent Raney-Nickel catalysts, copper and ah.:lminum drosses, and. other metal containing wastes were investigated. The paper summarizes the most significant findings

Jan 1, 1995

By Tatsuo Itou

Both sales volume of Aluminum Can and its recycling rate are remarkably increasing here in Japan. In 1993, recycled can volume was 11.78 billion cans ( 116,258 metric tons ) and its recycling rate 57.8 percent. We, MITSUBISHI MATERIALS CORPORATION. the leading manufacturer of aluminum can in Japan and our affiliated companies are very deeply involved in recycling used beverage cans ( U.B.C ) and recycling them back to can stock. In this paper. I would like to present the following; 1. Recent trend of beverage can consumption in Japan. 2. Trend of aluminum can and its recycling rate in Japan. 3. Future of aluminum can business in Japan.

Jan 1, 1995

By Yanhui Liu, Xuewei Lv, Chenguang Bai

A thermodynamic model for determining the surface tension of molten slag by considering the surface tension and molar volume of the pure oxide component, and their ionic radii was extended to the slag bearing high TiO2 (varying from 80 to 67%) at 1973 K. The iso-surface tension curves for the FeO-TiO2-Ti2O3 ternary system at 1973 K are almost parallel to the FeOTi2O3 line. TiO2 plays a role of surface-active solute, and its surface-active effect is attenuating with increasing the TiO2 content. The iso-surface tension curve shifts away from the TiO2 corner, indicating that the surface tension of the ternary slag decreases along with the addition of SiO2. The reasons include the addition of SiO2 with lower surface tension and the decrease of the total ion moment at the surface. Both CaO and MgO can bring about that the iso-surface tension curve shifts towards the TiO2 corner, indicating that the surface tension of the ternary slag increases along with the addition of CaO or MgO. CaO has a more pronounced effect on increasing the surface tension of the ternary slag than MgO at an equimolar amount addition. The increase of the surface tension results from both the compositional change and the variation of the slag structure.

Jan 1, 2015

By T. Innmi

The potential of the nickel matte anode was measured during the matte electrolysis in the commercial cell. The slime layer consists of elemental sulfur and was found to greatly influence the potential of anode. The measurements of porosity and permeability of the slime suggest that the voltage drop of the slime layer dominates the potential. Furthermore, the diffusion of the electrolyte through the slime layer is also one of the factors to determine the potential. In addition, the copper content of the nickel matte anode was found to affect the change in the anode potential during the electrolysis. The role of copper on the anodic dissolution of nickel matte is discussed in this work.

Jan 1, 1988

By Boyd Davis, Vladimiros Papangelakis, Joshua LaMarre, Jan de Bakker

"HCl leaching using molten salt hydrates has the potential to improve the extraction of nickel from laterite ores. However, as in other HCl leaching applications, recovery of HCl is key to process economics. Spray pyrohydrolysis, which is used in current chloride-based flowsheets, is associated with a high energy cost. The authors have developed a proposed laterite leach circuit using an alternative HCl recovery route. The leach circuit envisions a leach by concentrated (33%) HCl in an MgCl2 molten salt hydrate (MSH) or brine medium, followed by Ni/Co recovery and iron precipitation. Magnesium and chloride are precipitated from solution as magnesium hydroxychloride; this hydroxychloride is thermally decomposed to produce HCl gas. The proposed flowsheet employs a chloride leach circuit with simpler equipment and lower energy cost than in the conventional practice of pyrohydrolysis. Laboratory work investigated key aspects of the flowsheet, including precipitation of magnesium hydroxychlorides and their composition; magnesium hydroxychloride thermal decomposition; and iron control.Introduction As sulphide nickel ores become harder to mine and more complex to process, laterite ores will increase in importance. Laterite ore deposits can be divided into two main mineralogies. Limonite ores consist mostly of hydrated iron oxide, FeOOH, with 1-3% nickel substituting for the iron. Saprolite ores consist of iron-magnesium silicates, (Fe, Mg)2Si04, again with some nickel substituting for the metal ions. Limonite ores can be treated using the HP AL (High Pressure Acid Leach) process, in which the ore is reacted with sulphuric acid at high temperature in an autoclave. HP AL, however, cannot in general be used to treat saprolite ores because the magnesium enters solution and consumes sulphuric acid, which results in excessive spending on lixiviant. It is therefore desirable to find a hydrometallurgical process specifically for saprolite ores that can provide better results than the treatment options currently available."

Jan 1, 2011

By K. Yamada, T. Takaoka, A. Ozeki, M. Yamaga, Y. Kawai, S. Nishioka, Y. Kikuchi

"Recently, smelting reduction of chromium ore in BOF has been actively investigated as a key unit process for an innovative future stainless steelmaking. The prominent feature of this new process route is energy and process saving, and production cost saving. The development is already in the midst of application to the commercial production, however there still remain the following key technologies to be established for the full use of the process. One is a speed up of the reduction of chromium ore to match with sequential continuous casting, and the other is efficient combustion of carbonaceous materials in BOF to reduce their consumption, and hence to assure the steel quality. High degree of post combustion technology and new charging technology, i.e., ore-coal-flux-oxygen mixed injection, could be effective for those two subjects. In 2000 or beyond, the new process would have become quite popular owing to the establishment of those key technologies.Introduction Since stainless steel was invented, its production has continued to expand because of its attractive combinations of functions of excellent corrosion resistance, good formability, a pleasing appearance, and a wide range of strength levels. New types of stainless steels as well as new applications are continually being developed.Compared to the production of ordinary steels (1), stainless steel production (2,3) shows steady growth worldwide, while the former production remains on the same level, as Figure 1 shows. It can be estimated that future production would show further growth since materials consumer demands are more fashionable, or more functional, which could be satisfied by stainless steels.Thus market needs would be met, if it could be produced with reasonable production cost. The emergence of an innovative production technology is then potentially requested as VOD and AOD processes have emerged, which has saved substantial production cost. This paper describes a possibility of a future stainless steelmaking process, which uses the in-bath smelting reduction of chromium ore in BOF, and which would save production as well as energy cost."

Jan 1, 1988

By Vaughan R. Voller

"Over the last ten years an increasing number of heat and mass transfer models of solidification processes have been presented in the literature. A key component in these models is the coupling between thermal and solute fields. This is achieved by developing relationships based on the behavior at the microscopic scale in the casting (typically a secondary dendrite arm space). An important class of models in this respect are models that describe the local scale redistribution of solute alloy components-collectively referred to as microsegregation models. This paper explores this class of models.IntroductionModeling takes a key role in processing materials for properties. This is particularly time in solidification processes where current computer techniques allow for a detailed treatment of the critical macroscopic phenomena. Typically these macro scale models consist ·of three main coupled components.1. A model of flow in the melt and solid + liquid mushy region.2. A model of heat transfer.3. A model of solute transport.The focus of this paper is the solute transport component, in particular the manner in which process scale transport is coupled to transport ·at the local scale of the solid-liquid interface. This step requires a modeling of the redistribution of solutes at the scale of the secondary arm spaces in the dendritic mushy region-a process referred to as microsegregation. Basic microsegregation models use the limit assumptions of no mass diffusion in the solid (Gulliver-Scheil [l]) or complete diffusion in the solid (equilibrium lever rule) in a fixed and space. Recently, however, more sophisticated microsegregation models that account for finite mass diffusion and coarsening of the arm space have been developed [2-19]. In this paper governing equations for a general microsegregation model for a multi-component alloy in a coarsening and spacing _are introduced. From these general equations various models for a binary system are developed and tested"

Jan 1, 2000

By Shen Shen, Paul R. Ohodnicki, Samuel J. Kemion, Vladimir Keylin, Alex Leary, Joseph F. Huth, Michael E. McHenry

"Recent DOE workshops highlight the need for advanced soft magnetic materials leveraged in novel designs of power electronic components and systems for power conditioning and grid integration. Dramatic weight and size reductions are possible in these applications through operating at increased frequencies. This manuscript discusses processing and composition design approaches for optimizing FeCo-based nanocomposites for higher frequency operation at 100 kHz and above. The proposed strategy involves starting with prior compositions known to exhibit high inductions, optimal field crystallization induced anisotropy, and excellent mechanical and high temperature magnetic properties. Proposed alloy modifications for the applications of interest would include increased amorphous phase resistance, optimum induced anisotropy, and minimized or carefully engineered magnetostriction. Relevant process developments would target reduction of ribbon thickness by optimizing the casting process or post-processing treatments such as chemical thinning or rolling. Three archetypes FeCo-based nanocomposites are described including near equiatomic FeCo-based, Fe-rich and Co-rich alloys.MotivationSilicon steels are widely applied for 60Hz utility-scale transformers [1]. For applications at high frequencies, however, Si-steels exhibit unacceptable losses and ferrites are typically used due to their high electrical resistivity and good soft magnetic properties [2]. However, the low inductions offerrites have limited their applications in power electronics. Developments in rapid solidification have led to amorphous metal alloys and controlled nanocrystallization processing has resulted in state-of-the-art amorphous/nanocrystalline nanocomposite soft magnets [3-5]. Commercial utility-scale transformers made with Fe-based amorphous materials have been demonstrated to result in significant energy savings with an associated reduction in greenhouse gas emissions [6]. DOE workshops held in 2010 emphasized a need for advanced soft magnetic materials for the next generation of power electronics. For advanced power conditioning and grid integration applications, frequencies of 20 kHz up to -1 MHz are of interest depending on the power level [7]. Here, we review previous work and discuss the approaches to optimize FeCo-based nanocomposite materials for high frequency applications."

Jan 1, 2012