Search Documents

By Paul S. Korinko, Simona E. Hunyadi Murph

To address a radiological contamination event, a materials and process project was initiated. During the course of this project, processes and materials were developed that successfully captured zinc vapors physically and chemically, respectively. However, the physical traps were placed in an undesirable area and it was determined that the chemically captured zinc reactions was reversible. Consequently, advanced nanomaterials are being developed to capture zinc vapors. The current state of the art of the science and engineering of these materials and their efficacy for zinc capture and retention is discussed in this paper.

Jan 1, 2015

By Cong Wang, Siyang Long, Pengcheng Zhang, Haibin Zuo

The present study describes central segregation of the High-carbon steel billets of 150mm square and its heredity to the following hot-rolled wire rods, whose sizes are 10mm and 6.5mm in diameter separately. The relationship between center segregation of the billets and solute element distribution of rods, the mechanical properties and microstructure of rods were studied experimentally. The results show that segregation index of C is higher than that of Mn. With the increase of central segregation, the stability of the mechanical property of the rods becomes worse. The formation of carbide network and central martensite in the rolled products can be attributed to the heredity of the as-cast central segregation. The 6.5mm-diameter-rod has higher tensile strength than that of 10mm diameter which might be due to bigger reduction ratio. Thermo Mechanical Control Process (TMCP) should be used together with Billet Centersegregation- controlling (BCSC) to improve the overall properties of rolled products effectively.

Jan 1, 2016

By XING Xiangdong, Zhang Jianliang, MA Jinfang, WANG Zhenyang

The non-equilibrium reflux reaction behavior of phosphorus was studied with synthetic slags formed by using the AR chemical reagents and changing the initial condition of basicity, FeO, MgO and Al2O3. Due to increase of viscosity, the dephosphorization slag with high basicity inhibits the full contact of slag with iron, which leads to the low reaction rate in the early stage. However, since the high basicity improves the activity coefficient of CaO, the dephosphorization rate and phosphorus capacity goes up in late reaction stage. FeO promotes the increase of reaction rate in early dephosphorization stage. But the polarization force of Fe2+ is stronger than Ca2+, which hinders the reaction between phosphate ion and CaO and reduces the stability of PO4 3-. Thus, high content of FeO will adversely impact on dephosphorization reaction. In addition, MgO has a promoting effect to the dephosphorization, whereas Al2O3 has a negative influence.

Jan 1, 2016

By Esperidiana A. B. Moura, Célio H. Wataya, Roberta A. Lima, Rene R. Oliveira

The purpose of this study was to investigate the mechanical, morphological and thermal properties of biodegradable composites based on aliphatic-aromatic copolyester/polylatic acid blends (PBAT/PLA blends) reinforced by açaí seed fibers, an abundant byproduct of the açaí fruit agro industry. The biodegradable polymeric composites were prepared by melting extrusion process using a twin-screw extruder machine. The fibers removed from the açaí seed were used as the reinforcement and PBAT/PLA blends as the matrix. The influence of the açaí seed fibers addition on properties of composites was investigated by tensile and impact tests, SEM, DSC, and XRD analysis. Correlation between properties was discussed. In addition, açaí seed fibers characterization by SEM, XRD and WDXRF have also been carried out. The addition of açaí seed fibers on biodegradable PBAT/PLA blends showed that it is possible to get interesting property gains in biodegradable polymer by using waste from renewable sources.

Jan 1, 2015

By Larry G. Twidwell, Jannette L. Chorney, Bryce D. Ruffier, Katelyn M. Lyons, Daniel W. Gaede, Ryan J. Foy, Jerome P. Downey

The Army Research Laboratory (ARL) has an interest in the recovery and processing of rare earth elements. At Montana Tech, elevated temperature chlorination of rare earth oxides is presently being investigated as a potential methods leading to the selective separation and recovery of rare earth elements from mineral ores and concentrates. After preliminary evaluation, ytterbium oxide was selected as a representative surrogate material for more extensive chlorination studies. Methods used to determine the conversion and recovery include X-ray diffraction (XRD) and inductively coupled plasma (ICP) analysis. These data have been used to establish and confirm process conditions that consistently yield high conversion efficiencies. Based on the promising results, further experimentation is underway to ascertain the metallurgical response of other rare earth oxides and carbonates to the roasting process. The end goal is to create a robust process for industrial application that has greater efficiency and reduced costs as compared to current practice.

Jan 1, 2015

By Mei-le He, Min Chen, Xiang Shen, Lei Xu, Lei Liu, Nan Wang, Xue-liang Yin

In the current study, Al2O3-MgO-CaO refractories were prepared at 1400-1600 by the addition of MnO micro-powders, and the effect of MnO addition on densification behavior of the refractory was discussed. The results showed that the doped MnO dissolved to MgAl2O4 phase, and promoted the growth of MgAl2O4 grains by the formation of MgAl2O4 solid solution. As a result, the dense microstructure was obtained, with the apparent porosity decreased from 19.2% to 5.4% and the bulk density increased from 2.78g/cm3 to 3.15g/cm3 after firing at 1600 for 2h by the addition of 4% MnO. In addition, a texture microstructure was observed, which is considered to be favorable to improve mechanical properties and the service life of Al2O3-MgO-CaO system refractories.

Jan 1, 2016

By Maria K. Kojo

The interaction between various slags and a nickel concentrate containing pyrite, pentlandite, and violarite were investigated by submerging concentrate pellets in molten slags. The slags were contained in MgO-A12O3 spinel crucibles. The slag oxidizes the iron sulfides in the concentrate, resulting in a nickel matte. The amount of S02 gas formed during reaction was measured to determine the oxidation reactivity of the slags. The experimental variables included temperature, the ferric/ferrous ratio of slag, and other slag properties such as the FeO/SiO2 ratio and the MgO and NiO contents. The reactivity of the slag depended in a complex manner on its oxidizing power, viscosity, and interfacial tension. The slag composition for the greatest reactivity was determined to be Fe3+/Fe2+ = 0.3, Fe/SiO2 = 1.3, and % MgO = 2. This slag, however, caused substantial foaming. Increasing the MgO content to 10% or replacing it by 5% MgO + 8% NiO eliminated at a slight decrease in reactivity. The implications of the findings from this work in the bath smelting of nickel sulfide concentrates are discussed.

Jan 1, 1995

By Mingchun Lu, Zhe Wang, Mingming Cao, Xiangdong Xing, Shan Ren, Jianliang Zhang, Zhengjian Liu

"The effect of reduction temperature on the vanadium titano-magnetite carbon composite pellets was investigated by X-ray diffraction (XRD) and scanning electron microscopy (SEM), and the discussion has put emphasis upon the enhanced reduction mechanism of additives containing CaF2 and NaF in this paper. The results showed that the reduction temperature of 1350°C was needed for the generation, mergence and growing up of metallic iron as well as monomer dissociation between metallic iron particles and slag phase in the vanadium titano-magnetite metallization pellets. The iron compound was completely reduced into metal iron, and Fe2Ti04 was mainly transformed into metal iron, (Fe,Mg)Ti205 and FeTi03 at 1350°C. The maximum metallization ratio was only 88.5% at 13500 for 30 min without any additive. However, with the addition of 3.0% CaF2 or NaF, the metallization degree of pellets could reach up to 94.8% and 92.5%, respectively.IntroductionVanadium titano-magnetite which is mainly distributed in the area of Panxi, Chengde and Maanshan in China is a kind of complex iron ore which contains various valuable metal elements such as iron, vanadium, titanium, etc. Among the above areas, Panzhihua (Sichuan Province in China) area possesses the largest deposits of vanadium titano-magnetite and the future reserves are more than 100x108t, and the reserves of Ti existing as Ti02 reach to 8.7x108t which occupy over 91% of the whole nation and ranked No.1 in the world[1]. Lots of researches on the comprehensive utilization of vanadium titano-magnetite have been conducted in the world. And many technological processes have been applied successfully in industrial production. Among these processes, the process of rotary kiln-electric furnace is employed to recover iron and vanadium in South-Africa, while the process of blast furnace-rotary furnace is widely used in Russia and China. Besides, many researchers have made efforts on employing new direct reduction process to realize the effective comprehensive utilization of vanadium titano-magnetite[2-4]. However, the direct reduction process is only researched in laboratory and it has not been used in industry."

Jan 1, 2013

By Robert E. Moore

Synthetic spinel is proving to be a highly effective refractory for specific applications, but its cost limits applications. Formation of spinel from a raw material such as diaspore or bauxite could provide a suitable and less costly starting material. In the study reported here, finely ground (-325 mesh) diaspore from Missouri and bauxite from Guyana and China are combined with hardburned MgO (-325 mesh) in appropriate proportions to yield spinel and spinel with secondary phases. A classical sintering and creep study was completed, accompanied by a microstructure study to determine completeness of the reactions and morphologies of the reaction products.

Jan 1, 1991

By Arpad E. Tonna

Recycling of materials from lithium-oxyhalide batteries is a complex task, since the dismantling of batteries is associated with many hazards. The electrolyte and the lithium anode metal are extremely reactive in the presence of water or water vapor. Therefore, the dismantling process is a complex task. In this process, the lithium battery is electrically discharged, then frozen in liquid argon, and cut into small size pieces. These are fed into an incinerator, where the unreacted portion of lithium metal, thionyl chloride, plastic separators and carbon paste are decomposed and burned to gaseous products. The aluminum, iron (steel) and nickel pieces are recovered as saleable scrap metals. The off-gases are scrubbed with an alkaline sodium carbonate containing solution. The clean gases are released to the environment. The particulate mater recovered from the scrub-suspension would be available as additive to the cement industry . The recycling of battery decomposition products improves the economic viability of the disposal processes. Work is in progress to develop safe handling, processing and recycling large size lithium batteries.

Jan 1, 1995

By R. Y. Wan

Low grade sulfidic-carbonaceous refractory ore from Newmont Gold Company's Carlin deposit was microbially pretreated. The biological pretreatment process gave partial oxidation of the sulfidic components of the refractory ore but the preg-robbing carbon continued to be active resulting in approximately zero cyanide gold extraction. A 495 ton pilot plant test heap was conducted using acidic thiourea leach following biooxidation. Activated carbon and cation exchange resin adsorption were tested for gold recovery from the thiourea pregnant solution. The results obtained from the test heap were not satisfactory. Gold extraction was low due to slow reaction kinetics which was caused by relatively large particles and very low winter temperatures. Problems existed in the thiourea-test heap and are discussed in this paper. An alternative heap leach process using thiosulfate has been successfUl at the pilot scale for gold extraction following biooxidation pretreatment of refractory sulfidic-carbonaceous ores.

Jan 1, 1995

By K. A. Brunk

Newmont's research, operations, history and experience with pre-treatment of preg-robbing carbonaceous ores are described, with emphasis on the chemistry, physics and kinetics of chlorine treatment. Present operations, control strategy and projected changes are also described, including a summary of the adsorption of chlorine into pulps and off-gas scrubbing. Conditions of chlorination have been optimized by the use of Eh-pH diagrams of the gold-chlorine-water system, and have resulted in significant increases in gold recoveries and decreases in chlorine consumptions.

Jan 1, 1987

By K. S. Izbakhanov

The Chimkent Lead Plant was constructed in 1934 and since that time has undergone many revisions. In 1975 the slag fuming operation was changed from pulverized coal to natural gas fuel. In 1981 the slag fuming furnace water jacket system was converted to evaporative cooling with high pressure steam production. The impact of these changes and the method of their application are described.

Jan 1, 1990

By Qingchun Yu, Baoqiang Xu, Yongnian Dai, Bin Yang, Fulong Zhu

"In this paper, the mechanism of the carbothermic reduction-chlorination process to extract aluminum from alumina in vacuum was investigated. The carbon monoxide (CO) content of the gas, phases of the reduction slag, surface morphology of the reduction slag and the product aluminum were measured by means of gas chromatography (GC), XRD, and SEM. The experimental results indicated that the content of CO in the gas decreased, but Al4C3 increased with time at 1773K during the carbothermic reduction process of alumina. AlCl(g) and graphite (C) were produced by the reaction between Al4C3 and AlCh(g) at 1773K, and then aluminum beads generated after the decomposition of AlCl(g). It implied the mechanism of alumina carbothermic reduction-chlorination process in vacuum involves three steps as follows: the carbothermic reduction of A}z03 to produce Al4C3, the chlorination of Al4C3 by AlCh(g) to produce AlCl(g), and the decomposition of AlCl(g) to produce Al(l).IntroductionAluminum is the basic raw material for many industries [1], and it is used extensively because of various excellent properties such as light weight, good malleability, high strength, excellent thermal conduction, high corrosion resistance and so on [2]. Industrial production of aluminum currently includes refining alumina and electrolytic aluminum processes. However, its development has been effected by some factors such as high energy consumption and heavy environmental burdens [3]. In the past several decades, there had been numerous attempts to produce aluminum by new methods. Extracting aluminum from alumina or bauxite directly by carbothermic reduction-chlorination process had been studied [ 4-6]. Although the alumina carbothermic reduction process [7~9] had been studied, the mechanism of the carbothermic reduction-chlorination process had not been systematically elucidated.In order to investigate the mechanism of the carbothermic reduction-chlorination process in vacuum, GC, XRD and SEM techniques will be used to determine the CO content and to characterize the surface morphology and composition of the slags at various temperatures."

Jan 1, 2011

By Carlos Maurício Fontes Vieira, Sergio Neves Monteiro, Diogo Neves Henriques

"This work evaluates the effect of incorporation of an ornamental rock waste into an industrial clayey body used for roofing tiles fabrication. Formulations with 0, 10, 20 and 30 wt.% of waste were prepared by replacing the sand in the industrial clayey body. The plasticity of the formulations was determined by the Atterberg limits. Specimens were fabricated by 18 MPa press-molding and then fired from 850 to 1100oC. The specimens were tested to determine the water absorption, linear shrinkage and three points bending flexural strength. The results indicated that the waste improves the extrusion performance of the clayey body by decreasing its plasticity. The use of the waste was beneficial to the water absorption and mechanical strength of the fired clayey ceramic at temperatures above 1000 ° C.IntroductionOrnamental rock is a natural resource available in the municipal area of Santo Antônio de Pádua and located 150 km from the city of Campos dos Goytacazes, northe of state of Rio de Janeiro, Brazil. Intense industrial activity related to ornamental stones, especially gneisses, is traditionally occurring in the region. After mining, the flagstone is submitted to sawing to obtain blocks and then, after a manual operation, the final products are small flagstones [1,2]. During the sawing operation, a sludge composed of water and fine particles of rock is generated. A monthly production of 1000 tons of ornamental rock waste is estimated to be produced at Santo Antônio de Pádua. The final disposal of this waste has brought serious environmental problems. Since most industries do not have an adequate sludge treatment, the waste is contaminating the soil and underground waters as well as obstructing rivers and lakes.Ceramic bodies industrially fabricated in the municipal area of Campos dos Goytacazes, 280 km from the city of Rio de Janeiro, are still empirically elaborated using a mixture of local clays. These clays are predominantly kaolinitic mineral, associated with high plasticity. Due to the excessive plasticity of the ceramic bodies, it is common to have dimensional defects in the final products after the drying and firing processes. Moreover, the kaolinitic structure and the presence of aluminum hydroxide confer a refractory behavior to the local clays. This impairs sintering during the firing operation. In the case of clay ceramics for civil construction, this results in greater porosity associated with elevated values of water absorption and low mechanical strength [3,4]. To avoid these problems, it is necessary to reformulate the ceramic body composition. The addition of both non-plastic materials to reduce plasticity and fluxes to condition the refractoriness is a possible alternative."

Jan 1, 2008

By Duclerc Fernandes Parra, Washington Luiz Oliani, Christiano Gianesi Bastos Andrade, Ademar Benevolo Lugão, Danilo Marin Fermino, Francisco R. Valenzuela Diaz

This work concerns the study of the effect of discarded bond paper on the mechanical behavior of polypropylene/organophilic clay nanocomposites. A brown polycationic bentonite from the state of Paraíba, Brazil, was treated with sodium carbonate to transform it into a bentonite that swells in water and then treated with hexadecyltrimethylammonium ammonium chloride to transform it into a bentonite that swells in organic liquids. Polypropylene with 3 % polypropylene graft compatibilizer (PP-g-AM) was mixed with 1 % and 2 % by weight of discarded bond paper and with 1% and 2% by weight of organophilic clay using a twin-screw extruder. The specimens were prepared by the injection process. The clay as received and after organophilization was characterized by XRD, SEM, and capacity of swelling in water and in organic solvents. The nanocomposite specimens were characterized by XRD and thermal analysis. The mechanical behavior of the injected specimens was evaluated by strength, flexural and impact tests. The nanocomposites showed improved mechanical properties compared with the polymer without filler.

Jan 1, 2015

By Xuling Chen, Zhiyun Ji, Min Gan, Tao Jiang, Liang Yin, Xiaohui Fan

Straw char exhibited considerably faster burning speed than coke breeze for its porosity, which significantly degraded sinter quality when it replacing coke breeze as sintering fuel. In this investigation, preforming technology has been employed to densify raw straw. The properties of straw char preformed show that its density was increased, and the structure was also densified, which made the difference of combustibility between the straw char and coke breeze smaller. The proper preforming temperature, residence time and pressure were 200℃, 1min and 120MPa respectively. Sinter pot trials show that the product carbonized from preformed straw made the proper replacement ratio to coke breeze increase from 20% to 40%, and the emission reduction of SOx, NOx in flue gas increase from 11.50%, 14.15% to 37.85%, 23.60% respectively, compared with non-preformed straw char.

Jan 1, 2015

By Yuanpei LAN, Minren XU, Deliang NIU, Zhu WANG, Qingcai Liu, Shan Ren

Removal of gas is the major function of RH degasser. To optimize the RH refining craft in Chongqing Iron and Steel Co. Ltd, the degassing effect of RH degasser at different degrees of vacuum was investigated using a vacuum induction furnace. In addition, the effect of processing time on the gas content dissolved in molten steel was also studied. The results showed that degree of vacuum was one of the important factors that determined the degassing efficiency in RH refining process. High vacuum degree is helpful in the removal of gas, especially in the removal of [H] dissolved in molten steel. The processing time could be reduced from 25-30 min to 15 minutes and gas content could also meet the demand of RH refining

Jan 1, 2015

By Zhongning Shi, Ramana G. Reddy, Min Li, Zhaowen Wang

Electrodeposition of cobalt from cobalt tetrafluoroborate (Co(BF4)2) was investigated using 1- butyl-3-methylimidazolium tetrafluoroborate (BMIMBF4) ionic liquid. The experiments were conducted at 353 K. Chronoamperometry experiments confirm that the electrodeposition of cobalt on tungsten electrode proceeds via three-dimensional instantaneous nucleation with diffusion-controlled growth process. The average diffusion coefficient of Co(II) was found to be 7.5 × 10-8 cm2s-1 at 353 K, which is in good agreement with the estimated value from cyclic voltammetry. The electrochemical deposit was characterized using SEM-EDS and XRD methods. The SEM image shows formation of a dense and compact deposit at - 0.75 V. The EDS and XRD analysis confirm that the obtained deposit is pure cobalt metal.

Jan 1, 2015

By Yapeng Zhang, Zhiwen Shi, Chaoquan Yao, Fei Wang, Xinyu Li, Jianliang Zhang

A great deal of iron ores which have special elements have been applied in the sintering process with the decreasing of high-grade quality iron ores resources. In this paper, the laterite nickel ores were added into three different kinds of iron ores respectively to make liquid phase formation research by software of Factsage and high temperature characteristic sintering experiments. The results showed that the adding proportion of laterite nickel ores should be less than 15% when the high temperature properties of the mixing ores were well. Increasing the mixing ration of laterite nickel ores in the sintering blending would play an important role in the reduction of the sintering cost.

Jan 1, 2015