Search Documents

By Ruiling DU, Jiazhi Zhang, Yong Zhao, Keng Wu

Reaction kinetics of metallurgical physical chemistry which was successfully applied in metallurgy (as ferrous metallurgy, non-ferrous metallurgy) became an important theoretical foundation for subject system of traditional metallurgy. Not only the research methods were very perfect, but also the independent structures and systems of it had been formed. One of the important tasks of metallurgical reaction engineering was the simulation of metallurgical process. And then, the mechanism of reaction process and the conversion time points of different control links should be obtained accurately. Therefore, the research methods and results of reaction kinetics in metallurgical physical chemistry were not very suitable for metallurgical reaction engineering. In order to provide the definite conditions of transmission, reaction kinetics parameters and the conversion time points of different control links for solving the transmission and reaction equations in metallurgical reaction engineering, a new method for researching kinetics mechanisms in metallurgical reaction engineering was proposed ,which was named stepwise attempt method. Then the comparison of results between the two methods and the further development of stepwise attempt method were discussed in this paper. As a new research method for reaction kinetics in metallurgical reaction engineering, stepwise attempt method could not only satisfy the development of metallurgical reaction engineering, but also provide necessary guarantees for establishing its independent subject system.

Jan 1, 2015

By I. Filzwieser, S. Wallner, M. B. Hanel, A. Filzwieser

Whenever thinking about increasing tankhouse performance two major aspects has to be considered, the technological feasibility as well as the economical impact. For meeting the requirement of an increased current density leading to an increased productivity, Mettop has developed the METTOP-BRX Technology, which allows the introduction of fresh electrolyte between each pair of anode and cathode. As an example of a green field approach the installation at Xiangguang Copper Co., Ltd will be described. Since the start up in 2011, Xiangguang Copper Co., Ltd operates one of their two copper refining tankhouse with a current density of 420 A/m2 and a current efficiency above 98% in average. At Montanwerke Brixlegg Ag, as an example of a brownfield installation, the annual production could be increased by 50%. Although for many years a total of two industrial applications are in operation, the successful implementation of this technology that result in significant operational and economic advantages has not been fully accepted within the industry due to misunderstandings, incorrect interpretations and lack of awareness. It is intended with this paper to create a better understanding about the parallel flow technology and help to eliminate worries and concerns.

Mar 1, 2017

By Heric Henrique Souza e Silva, Johne Jesus Mol Peixoto, Natalia Barros Barony, Itavahn Alves da Silva, Weslei Viana Gabriel, Carlos Antonio da Silva, Varadarajan Seshadri

In this work the circulation rates have been determined in a 1:7.5 scale physical model of RH reactor (Ruhrstal Heraeus) and using oil/water and oil/zinc chloride solution to simulate steel melt/slag in the prototype with the objective of evaluating the influence of density and viscosity on the entrainment of oil simulating slag. A technique based on strain gage bridge and particle image velocimetry was developed to assess the circulation rate, as the usual tracer method is not feasible due to the presence of chloride ions in ZnCl2. The critical velocity and critical diameter of oil drops for slag (oil) entrainment in water/oil and ZnCl2/oil systems were estimated using equations from the literature. Due to the difference in density, the ZnCl2/oil system, showed a critical velocity that is 28% higher than the silicone oil/water system while the maximum size of the entrained droplets was about 65% lower than that for water/oil system.

Mar 1, 2017

By Y. H. Liu

Several foaming aluminum samples of different density were prepared in a semi?industrial scale experimental system, Their properties such as the energy absorption characteristics, mechanical properties, heat conductivity and acoustical properties were measured. The results showed that the foaming aluminum with a density of 0.5 to 0.6 g/em3J has the best energy absorption and this makes it suitable as the ensuring bar of the automobiles and also as a cushion material for the engine. The foaming aluminum with a density of 0.25 to 0.4 g/em3 has the best acoustical properties and heat conductivity resistance, which is suitable for the door filling material, the ceiling and the partition or the car engine.

Jan 1, 2003

By N. Shi, T. C. Lowe, S. J. Zhou, M. L. Lovato, Y. T. Zhu, J. A. Valdez, W. R. Blumenthal, M. G. Stout

"A major problem of short-fiber composites is that the interfaces between the fiber and matrix become a limiting factor in improving mechanical properties such as strength. For a short fiber, a strong interface is desired to effectively transfer load from matrix to fiber, thus reducing the ineffective fiber length. However, a strong interface will make it difficult to relieve fiber stress concentration in front of an approaching crack. Stress concentrations result in fiber breakage. We report in this paper an innovative approach to overcome this problem: reinforcement morphology design. Short-fibers with enlarged ends are processed and used to reinforce a polyester matrix. The initial results show that the bone-shaped short-fibers produce a composite with significantly higher strength than can be attained with conventional short, straight fibers.IntroductionThese interfaces between the fiber and the matrix in short-fiber composites play a critical role and, in many cases, become a limiting factor in improving such mechanical properties as strength and toughness of the composites (1-4). For a short fiber, a strong interface is desired to effectively transfer load from matrix to fiber. A stronger interface can reduce the ineffective length at both ends of the fiber and, therefore, can increase the effective length that carries load (5-9). However, with a strong interface it is difficult to relieve fiber stress concentration -in front of an approaching crack; and such stress concentration can result in fiber breakage (10, 11). This effect is particularly severe for ceramic matrix composites, because of their low matrix toughness and lack of plasticity. Even for a composite with a highly ductile matrix, such as plastics, too strong an interface may still cause successive adjacent fiber breakage and subsequently reduce composite toughness (1, 11). On the other hand, a weak interface significantly decreases the fiber load-carrying length due to ineffective load transfer and complete fiber interfacial debonding and pullout during loading. A compromise in the interfacial bond strength will also compromise the load-carrying potential of short fibers."

Jan 1, 1998

By C. Peter Hayes

The world continues to change and with it the supply of minerals and metals, the location of centres of production of primary metal and the increasing levels of metals and materials recycling. New technologies are being developed to meet the ongoing search by industry for lower costs, cleaner production and new markets. To keep abreast with these changes, and to utilise fully, the potential benefits of these technical advances, the industry will need a professional workforce having different knowledge, skills and professional attributes than in the previous millennium. What are these skills and attributes? How to best attract and develop the metallurgists of the future, and provide for the ongoing educational and research needs of the industry?

By G. Belardi

The purpose of the study was to check on the level of environmental contamination and to design a project for cleaning up the Abetina Mine area at Piancastagnaio (Grosseto, Italy). Contamination of this area had occurred during the mining and treatment of cinnabar (HgS) over a prolonged period. The aim of the project is to remove the sources of contamination or render them harmless. Mining of the Piancastagnaio deposit started in 1840, mercury metal being extracted from the ore by thermal treatment. Together with Spain, Italy was the first country to produce this metal and was the world leader in this field between 1936 and 1943. Though mercury production in the Monte Amiata region of Tuscany ceased in 1974 the ensuing environmental impact is very evident, taking the form of rusty old mining and processing works, plus waste tips which still contain considerable amount of mercury even after the ore had been subject to thermal extraction treatment. The research which has been conducted included mapping the area to identify the main sources of mercury and arsenic pollution, as well as the level of environmental contamination. Mercury and arsenic values in excess of 16,000 and 150 ppm respectively are encountered in the most highly-contaminated places. The cleanup project has been drawn up on the basis of the field and laboratory investigations. This provides for a combination of remediation measures on the land concerned, as well as in situ inertization of contaminating elements by means of mixtures of chemical compounds such as cyclosiloxanes. Due account has been taken of Italian and EU environmental regulations when establishing the measures for rendering the various polluting element innocuous. 'The efficacy of the inertization techniques has been checked by yield tests in acetic acid and carbon dioxide, reducing the Hg and As contents of the material in the untreated and treated states from maximum values of 7 mgll to minima close to zero.

Jan 1, 1996

By Mark William Kennedy

Modern metallurgical plants typically have complex flowsheets and operate on a continuous basis. Real time interactions within such processes can be complex and the impacts of streams such as recycles on process efficiency and stability can be highly unexpected prior to actual operation. Current desktop computing power, combined with state-of-the-art flowsheet simulation software like Metsim, allow for thorough analysis of designs to explore the interaction between operating rate, heat and mass balances and in particular the potential negative impact of recycles. Using plant information systems, it is possible to combine real plant data with simple steady state models, using dynamic data exchange links to allow for near real time de-bottlenecking of operations. Accurate analytical results can also be combined with detailed unit operations models to allow for feed-forward model-based-control. This paper will explore some examples of the application of Metsim to real world engineering and plant operational issues.

Jan 1, 2014

By Liow Jong-Leng

A survey of the interactions of large gas bubbles formed from top and bottom injection of gases into melts was carried out. Spherical cap bubbles were found not to produce much splash when they break through the bath free surface except for that formed by plunging of the-spout at its edges. In contrast, the bursting of balloons produces cavities which give rise to liquid jets being ejected from the bath free surface. The position of the balloons relative to the bath free surface is an important parameter in the formation of the liquid jet. It is found that the interactions of multiple bubbles close to the free surface is important in determining the splash behaviour of gas injected systems.

Jan 1, 1996

By R. Boom, Y. V. Meteleva-Fischer, B. Kraaijveld, H. Kuntzel

"Segregation of impurities during refining of metallurgical grade silicon (MG-Si) is an option to produce solar grade silicon (SG-Si). Directional solidification is a last step in production of SG-Si effective for removal of metallic impurities. The possibility is investigated to use metallic impurities originally present in MG-Si for removing boron and phosphorus. MG-Si has been treated using two methods: 1) alloying with calcium and 2) refining with Na2O-CaO-SiO2 slag, both by controlled cooling. The microstructure of silicon and the impurities distribution have been studied before and after the treatments. Using EPMA phosphorus and boron have been detected in 1-2 wt% concentration range in several intermetallic compounds in grain boundaries after both treatments. This observation points to a different possible mechanism of silicon refining from boron and phosphorus. Controlled cooling improves migration of phosphorus and boron to the silicide phases in grain boundaries, which can be removed by acid leaching treatment.2. IntroductionStandards for silicon solar cells and growing demand on “green” energy require economical and efficient route to the production of solar grade silicon. Refining of cheap metallurgical grade silicon is one of the promising options, where application of existing metallurgical approaches can result in cost-efficient production on industrial scale. Focus in refining is on impurities, which are most difficult to remove: B, P, Al, Ti, due to their large segregation coefficient in silicon and low vapour pressure [1]. Moreover, more environmentally friendly technology in comparison to the traditional Siemens process [2] will be in accordance with societal needs. Based on properties of common impurities in metallurgical grade silicon, alloying refining and slag refining are suggested as competitive techniques having potential effect on removal of impurities harmful for conversion of solar energy [3, 4]. Alloying with Ca followed by acid leaching was found to be effective for removal of Fe and Ti from silicon [5] and to enhance also removal of boron [6] and phosphorus [7, 8]. In the work of Inoue et al. [8] drastically increasing removal of phosphorus from silicon has been observed with an increase of Ca content and a thermodynamics-based explanation was provided. Since phosphorus has been found to condense in the secondary precipitate mainly composed of CaSi2, it can be removed together with iron and titanium by consecutive acid leaching treatment. Slag refining is one of the metallurgical methods proposed to be effective for refining of metallurgical grade silicon from boron [9, 10]. Slags with additions of the following oxides to silica have shown positive effect on removal of boron: CaO [11-13], Na2O [11,14]. Mechanism of slag refining from boron is based on oxidation of boron followed by its incorporation in the slag network [9,11]; the same mechanism is suggested for refining from phosphorus taking into account that oxides of boron and phosphorus are known as network-formers [15]."

Jan 1, 2012

By Ramana G. Reddy, Yuxiang Peng

The long-term corrosion behavior of Haynes 230 (H230) alloy in MgCl2–KCl eutectic salt was evaluated at 1273 K for 500 h in Ni crucible in argon gas. The results showed H230 alloy has good corrosion resistance. In addition, corrosion was noted to occur by depletion of Cr, which was deposited on the Ni crucible. Based on the calculation of Gibbs energy of Ni-Cr alloy and exchange current density of Cr in MgCl2–KCl, the Tafel model was constructed to investigate the corrosion potential and rate. The galvanic corrosion can be explained as the predicted results were in agreement with the experimental data.

Mar 1, 2017

By K. Yamaguchi, Y. Takeda

"Partial pressure - temperature - composition correlation diagrams of the Ga-As, In-As, Ga-P and In-P systems were contracted based on the obtained experimental data of the phase diagram and thermodynamic properties for the III-V systems. The total vapor pressures of arsenic or phosphorus at melting point of GaAs, InAs, GaP and InP were determined as 101, 10.1, 1510 and 253 kPa, respectively, at the corresponding melting points of 1509, 1211, 1739 and. 1336K , These diagrams are applied to the analysis of the horizontal Bridgman method and the liquid phase epitaxial growth technique. On the other hand, the analysis of the equilibrium state of the. chloride-CVD process was carried out using the data of the Gibbs energy of the compounds obtained by· authors.IntroductionThe group III-V compound semiconductors ate important materials used in optoelectronic liquid high speed electronic device. The crystal growth of the III-V compounds can involve processes that require contact between the solid, liquid and vapour phases at near equilibrium condition. Examples of processes that involve contact between the solid, liquid and vapour phases include bulk crystal growth such as the horizontal Bridgman and the liquid encapsulated Czochralski method and liquid epitaxy, and between the solid and vapor include chemical vapour deposition and molecular beam epitaxy. Therefore, the knowledge of the phase diagram and thermodynamic properties for the III-V binary alloys is essential for the analyses of crystal growth techniques of III-V compounds.For these reasons, a series of different · types calorimetric measurements had been carried out: (1) The heat contents of alloys for the Ga-As, In-As, Ga-P and In-P systems by a drop calorimeter [1;2,3]; (2) the heats of formation of the GaAs, InAs, GaP and InP compounds by a twin solution calorimeter [4]; and (3) the standard entropy of these compounds by an adiabatic calorimeter [5]. Based on the third law method, the Gibbs energies of these compounds were derived from the heat capacity, standard heat of formation and standard entropy data obtained by authors. Integral molar thermodynamic quantities of the liquid III-V .alloys were also determined from combining the heat contents of alloys with standard heat of formation and standard entropy data of the compounds· by applying the thermodynamic analysis method developed by Oelsen [6]. In the present study, the thermodynamic calculations for the crystal growth processes of the III-V compound were carried out using newly experimental data of the phase diagram and thermodynamic .properties measured by authors"

Jan 1, 2000

By Jan Smit

Sulphidic copper concentrates are generally processed by pyrometallurgical means; while oxidative pressure leach processing of such materials has been shown to be technically feasible, there has traditionally been little incentive to choose this route in favour of a smelting option. However, for concentrates with elevated arsenic levels, oxidative pressure leaching offers distinct advantages, as smelter air emission standards and restrictions on concentrate importation have tightened. The current state of pressure leach technology allows for high copper extractions from arsenical copper concentrates, while producing an environmentally stable process residue, without atmospheric emissions of sulphur dioxide or arsenic. In its studies on pressure leaching of copper concentrates, Sherritt has shown that arsenical feed materials can be converted into environmentally stable residues, with excellent copper extractions. The results of recent batch and pilot plant test work are discussed, including the deportments of copper, arsenic and precious metals.

By J. P. Bellot

During the non-ferrous metal processing, the melting step under vacuum or under rarefied gas leads to volatile metal losses. It is the case of the metallurgical processing of the nickel-based, titanium-based or zirconium-based alloys where the evaporation losses don't allow a sufficient control of the alloy chemical composition. A theoretical approach has been carried out involving both a continuum description in the liquid phase and a molecular approach in the rarefied gas phase. The finite volume method is used in order to solve the coupled transport equationsin the liquid, whereas the Boltzmann equation is modelled by using a Monte Carlo method. At the liquid metal and metallic vapor interface, the volatilization and recondensation fluxes link up the two calculations. Simulation results are given for the melting and refining of reactive metals such as titanium alloys where the control of the chemical composition remains a major difficulty. The validity of the kinetic Langmuir's law is discussed for different operating conditions.

Jan 1, 1996

By Zhao Hengxian

We studied the phase diagram of Na3AlFe-ZrO system, reduction of ZrO2 by aluminium and electrochemical behaviours of ZrO2 in the system. The results show that Na3ALF6-ZrO2 system is a simle eutectic one, that the velocity of reduction of ZrO2 in the system is rapid al 960'C and that the Zr content in the alloy abtained can reach as high as 2.5wt%. Potential scanning shows that there exist new current peaks on the potential scanning plats except for the cuurent peaks corresponding to the oxidation of aluminium. The method of making Al-Zr alloy in our paper has advantages over the traditional method of mixing metals.

Jan 1, 1992

By H. Senoh

For the purpose of clarifying the reason caused a drastic decrease of discharge capacity for MmNi3.6Mn0.4Al0.3Co0.7 electrode at relatively low temperatures, various factors influencing the charge-discharge processes were investigated in the temperature range of 25°C to -40°C. The charge efficiency obviously decreased at low temperatures less than 0°C due to a decrease in the rate of the charge-transfer reaction on the electrode surface. Moreover, both the rate of the hydrogen diffusion from the alloy bulk to surface and the rate of the charge-transfer reaction significantly influenced the high-rate dischargeability. The addition of Mo to MmNi3.6Mn0.4Al0.3Co0.7 alloy was found to be effective for improving the electrocatalytic activity, leading to the improvements of the charge efficiency and the high-rate dischargeability at relatively low temperatures.

Jan 1, 2002

By P. G. Comba

Many gold producing states are requiring rinsing of spent heaps to render the leached ore compatible with the environment and are placing restrictions on effluent pa, cyanide, and metals concentrations. Parameters which may affect efficient rinsing of heaps have been investigated by the U.S. Bureau of Mines in laboratory column studies. Rinse profiles for cyanide, metals, and pH as a function of the volume of water passed through the spent ore are presented. Fresh water rinsing of spent ore in columns showed that rinsing of cyanide was not affected by the rinse solution application rate. Interrupted rinsing with a rest period between applications reduced the volume of water required to meet effluent cyanide concentrations. chemical oxidation of the effluent with recycle of the rinse solutions reduced effluent cyanide concentrations and the volume of waste solution generated. Water rinsing was not successful in reducing the alkalinity of the cement agglomerated ore. A dilute acid solution had to be applied after cyanide removal to reduce effluent pa levels to specified limits.

Jan 1, 1992

By Emil B. Milosavljevic, Ljiljana Solujic

Cyanide is exceptionally reactive, and in typical gold/silver processing liquors, cyanide may be transformed into various species and forms depending on the mineralogy of the ore and chemical make-up of the process water. The exact speciation and relative concentrations depend on the Eh and pH values, as well as the free CN concentration in the system. Very good cyanide balances can be achieved by the judicious selection of the analytical techniques used. The choices an analyst has to make (which analytical methods to use and which ones to avoid) in order to gain better understanding of cyanide speciation and balances in a particular system under investigation will be discussed. Examples of cyanide balances obtained for the laboratory scale tests (agitated leach and column tests) will be presented and discussed.

Jan 1, 1999

By Masatoshi Ogasawara

Saganoseki smelter & refinery operated two flash smelting furnaces, producing a combined 330,000 metric tons per year (hereinafter mtpy) of copper. [n 1996, however, it successfully shifted to a single fumace operation while maintaining production at the same level. Since then, the production capacity has been further increased to the present 470,000 mtpy by technological improvements. Also, in order to reduce the converter load which represents a bottleneck in efforts to increase production, the matte grade was gradually increased and currently runs at 65 to 66% attaining the low copper content in the slag (hereinafter slag loss) of 0.7 to 0.8%. This ' paper introduces some improvements, recent operation results and thermodynamic analyses.

Jan 1, 2003

By Katsunori Yamaguchi

A new technique for the removal of tramp-elements from steel scrap has been required from the viewpoint of saving energy and protection of environment. In order to obtain fundamental information on the removal of copper, tin and zinc from molten iron, the extraction method by using of phase separation in the liquid Fe-Pb-C system was investigated at 1453K A mixture of iron, lead and carbon melted in a carbon crucible separates into two phases of lead and iron containing carbon. The compositions on the miscibility gap in' the Fe-Pb-C system are 95A%Fe-4.5%C-0.l %Pb and 99.9%Pb-0.1 %Fe. The distribution ratios of copper, tin and zinc between the lead and the iron phases, Lx=[masso/uX in molten Pb]/(masso/uX in molten Fe), are 2.2, 2.2 and lA, respectively. Seventy percent of copper and tin from iron scrap can be eliminated with comparable lead addition. Gold, silver and palladium are enriched in the lead rich phase, on the contrary platinum and rhodium are more distributed to the iron rich phase than to the lead phase.

Jan 1, 2003