Search Documents

By S. J. Buckler

Many chemical and metallurgical processes use submerged gas injection to increase contact area between gas and liquid phases in order to promote faster overall reaction or refining rates. The total interfacial area produced by gas injection through lances, nozzles or tuyeres is both an important design parameter for new vessels and a measurement for estimating the maximum processing capacity of existing equipment. Estimating total interfacial area from submerged injection into industrial pyrometallurgical vessels from existing knowledge is a problem with two aspects. The first difficulty is the difference in behaviour of cold (aqueous) and hot (molten metal) systems, implying that existing models and correlations of gas-liquid behaviour developed in low temperature systems are not necessarily appropriate for estimation of high temperature behaviour. The second difficulty is the issue of scale-up of correlations from laboratory to industrial sized vessels. The work presented in this paper is part of an ongoing experimental investigation, at the GK Williams CRC for Extractive Metallurgy, to quantify the total gas-liquid interfacial area available in pyrometallurgical vessels using chemical measurement methods. The effects of three operating variables, injected gas flow rate, nozzle diameter and nozzle submergence, on total interfacial area are quantified in a IOOL aqueous system - the first stage of a three stage process in examining the implications for scale-up of high temperature, medium-scale results are discussed. The results of work at high, injected gas flow rates (up to 500/min) show that the submerged Froude number is not sufficient for use as the sole variable in a predictive model of total interfacial area. Further work is being undertaken to identify other dimensionless variables that will better represent the gas-liquid characteristics in submerged injection that influence the formation of total interfacial area. The second and third stages of the experimental investigation involve measuring the total interfacial area in a large-scale (1000L) aqueous sodium sulphite and small-medium scale molten metal baths.

Jan 1, 2002

By Xia Zhao, Yong Zhao, Wen Pan, Ze-jun Ma, Yan-juan Yang

Characteristics of the gas-solid reduction reaction between iron ore sinter and carbon monoxide (CO) gas at 1273 K were studied with thermogravimetric analyzer. The microstructure, mineral compositions and porosity of sample were investigated prior to reduction, in the 30% reduced sample, in the 70% reduced sample, and in the fully reduced sample. At the reduction degree of 30%, the hematite and calcium ferrite was reduced to 44.4 and 60.4% respectively. At the reduction degree of 70%, all the hematite, calcium ferrite and magnetite were reduced to metal iron, only 36% wustite was left in the core area. The reduction reaction began with the loose structures and spread to the nearby area. In the area of micropores, the reducing gas can easily diffuse to the reaction interface to proceed the reduction reaction effectively. So increasing the content of micro-pores is an effective way to improve the reducibility of the sinter.

Mar 1, 2018

By R. M. Donovan

This paper documents the efforts to improve quality and production at the Amarillo Copper Refinery. It summarizes the change in attitudes, work procedures, equipment maintenance, instrumentation, and the ever changing market. The Amarillo Copper Refinery is dedicated to the ASARCO Management System, ISO-9002 and continuous improvement.

Jan 1, 1999

By G. C. Yao

Iron and silicon impurities can form needle and branch shape intermetallie compounds in molten aluminum when there is no manganese. It is difficult to separate them from molten aluminum by electromagnetic separation. The Fe-Si-AI and Fe-AI intcrmetallic compounds were transformed into Mn-Fe-Si-AI and Mn-Fe-AI compounds by the addition of manganesc into molten aluminum, In molten aluminum the morphology of these intermetallic compound particles is lumpish and spherical. Migration resistance of these impurity particles is small, which is beneficial to separation. FeSiMnAl4 and FeMnAl6 arc paramagnetic. These impurity particles can be moved by magnetic force and can be separated from the molten aluminum.

Jan 1, 2003

By R. Shimpo

Equilibrium calculations by a computer may sometimes fail in giving solutions when the system includes a large number of components and more than three phases, and especially when no definite information about stable phases is given. An improved method of calculation is presented in which the number of phases need not to be initially fixed, phases can appear or disappear in the course of' calculation and a new method is combined with the Newton-Raphson method to obtain solutions easily. The improved method is applied to the copper smelting operation and all the successive stages of the operation are successfully simulated.

Jan 1, 1983

By J. W. Matousek

Cobalt behavior in pyrometallurgical processes is traditionally analyzed using slaglmatte distribution coefficients as functions of matte grades or matte iron contents. L(s/m) = (%Co) I [%Co] = f [%CuNi] or f [%Fe] The method is inconvenient to use in predictive mass balance work because of the interdependence of assays and mass quantities. An alternative procedure is proposed based on cobaltliron ratios for slags and mattes: Js = (%Co) / (%Fe), Jm = [%Co] / [%Fe], and J, = b + m [Jm]

Jan 1, 1993

By Yafei Xiong, Yue Wang, Guotao Xu, Shuzhong Li, Huaiyuan Li

"The composition, properties and structure of taphole clay with high strength and friendly surrounding used in a new blast furnace with 3800 M3 volume was studied. The developed taphole clay had been applied in the blast furnace for four months, pouring times were 11-13 every day, flowing rate of hot iron was 7.5 t/min and the consumption of taphole clay was 0.49Kg per ton iron, which can make the new blast furnace attach the designed production quickly and decrease the cost of hot iron. The taphole clay is easy to be opened in the channel of hot iron which can be remained in stable shape under the corrosion of slag or hot iron, and it dose not produce poisonous smoke in yellow or dark color in the use process. The development of new taphole clay is useful to improve the work surrounding of the blast furnace.IntroductionIn the iron-making process, the taphole clay's function is filling up the taphole and protecting the formation as well as the growth of the clay in the blast furnace, maintaining the enough taphole depth; simultaneously it is easily to open a hole and knock out the clay. The taphole clay has a good performance of molten slag and hot iron resistance. The traditional taphole clay uses coal tar or carbolineum as a binder, and the performance of taphole clay is good, but it has the black and yellow poisonous smoke, which is harmful for work condition. Through the investigation on the binder's composition and poisonous performance of taphole clay, the environmental taphole clay is developed by some foreign companies, which is named the third generation product with benzene is less than 300ppm, and it has been used in European steel companies. This application of the taphole clay with high strength and environment-friendly using in 3800m3 blast furnace is introduced and the performance is discussed and analyzed in this paper."

Jan 1, 2012

By Lori Bassman, Cassandra George, Cullen McMahon, Md. Zakaria Quadir, Michael Ferry

"Complete and accurate analysis of subgrain microstructural features must include three-dimensional information. Three-dimensional electron backscatter diffraction (EBSD) data can be used to characterize these features; however their boundaries first must be determined. This cannot be accomplished simply with pixel-to-pixel misorientation thresholding because many of the boundaries are gradual transitions in crystallographic orientation. Fast Multiscale Clustering (FMC) is an established image processing technique that we have combined with quaternion representation of orientation to segment this kind of data. Segmentation algorithms often have issues handling images with both distinct and subtle boundaries. Our implementation of FMC addresses this by using a novel distance function and statistical analysis to take into account the variance in orientation of each feature. Although FMC was originally a twodimensional image processing algorithm it can be generalized to analyze threedimensional data sets. As an example, a segmentation of microbands in cold-rolled aluminum is presented.IntroductionThree-dimensional electron backscatter diffraction (3D-EBSD) is a method for mapping the local crystallographic orientations of points in a volume. The technique uses a dual beam platform consisting of a focused ion beam (FIB) and SEM with EBSD, where FIB is used for serial sectioning and EBSD for orientation mapping of 2D slices. These 2D slices may then be stacked to create a 3D volumetric data set.Typical uses of such a data set include characterizing the geometries and crystallographic orientations of surfaces between structures in 3D [1-5]. This involves identifying boundaries accurately, either in 2D slices with subsequent 3D reconstruction (as illustrated in Figure 1) or in the 3D data set. All such data sets present the challenges of i) aligning data slices to correct for instrument drift, ii) identifying relevant boundaries, and iii) implementing appropriate smoothing or interpolation algorithms. The focus of this paper is boundary identification."

Jan 1, 2011

By Ramiro Escudero G.

Since the introduction of column flotation almost forty years ago the column technology has grown into several non-mineral applications such as among others the effluent treatment, soils recovery and de-inking of recycled paper. Recent studies have demonstrated that particular characteristics of the dispersion (bubble size, gas holdup, bubble surface area flux) are needed for a given flotation column duty. In this work, two kind of spargers were tested (i.e., internal and external) using a 4 inch column lab in a two phase system. Results show that the external sparger provides a dispersion with characteristics that include those produced by the two internal spargers.

Jan 1, 2003

By Vincent Canaguier

Methane is increasingly considered as a promising reductant for metal oxides, including chromite. To assess the possibilities of such reduction route, the gas-solid reactions between Ar–CH4–H2 gas mixtures and synthetic chromites are studied between 950 and 1050 °C. The influence of Mg and Al additions on the reduction-caburization of (Fe,Mg)(Cr,Al)2O4 solid solution is investigated thermodynamically, structurally and kinetically. The product phases are examined by x-ray diffraction (XRD), scanning electron microscopy (SEM), and electron probe microanalysis (EPMA). The reaction rate is derived from real-time exhaust gas measurements and post-reaction product analyses such as oxygen analysis. Kinetic models are proposed based on the product phase morphologies and confronted with the empirical data.

By Olexandr Gydin

The evolution of grain and dislocation structures during cold deformation of the new steel LH800 of Salzgitter AG is investigated in the frame of this work. The main feature of this material is its ability to air-harden by carbon content of about 0.1%. The initial ferrite structure of the metal provides high plasticity at cold deformation and subsequent heat treatment increases tensile strength approximately two times. Described are results of in-situ tensile tests in the SEM. SEM and TEM analysis of grain and dislocation structures evolution in samples, which have been uniaxially deformed to certain strains, are carried out. After statistical evaluation of results the grain elongation against strain is determined. A microstructure of a deep drawn cup is analyzed by means of SEM. A quantitative evaluation of grain elongation on the different cup zones and comparison of these data with prediction results based on tensile tests are carried out.

Jan 1, 2009

By Caisa Samuelsson, Taishi Matsushita, Hannes Holmgren, Sina Mostaghel

"Rönnskär Smelter of Boliden Mineral AB, Sweden, is a large end-processor of secondary raw materials and waste, including electronic scrap. Electronic scrap may introduce various impurities to the smelter's flow-sheet, among which alumina is a common and significant one. This article summarizes the results of an ongoing research at Luleä University of Technology, Sweden, to study the influences of alumina on different properties of slag from the zinc fuming process at Rönnskär smelter. A combination of different experimental techniques and thermodynamic calculations have been used to investigate properties such as density, surface tension, effective thermal diffusivity, viscosity, and melting/leaching behaviors. Results show that the addition of alumina to this slag increases the degree of polymerization of the melt, and physical properties vary correspondingly. Mineralogy of the semi-rapidly solidified samples is also changed due to alumina addition. A correlation between mineralogy and leaching behavior can be observed.IntroductionBoliden's Rönnskär Smelter is a base- and precious-metals producer located in north of Sweden. Its main products are copper, zinc clinker, lead, gold, and silver. Sulphuric acid, liquid sulphuric dioxide and iron sand (granulated slag) are some of its main by-products. In order to optimize the overall outcome of the process, different refining units are integrated in the smelter's flow-sheet (Figure 1). Copper concentrates and fluxing materials (mainly silica sand) are charged to the process. The produced matte is sent to the converter and the generated slag is charged to the fuming furnace, where it is treated by reducing gases to produce zinc clinker. The converter's slag is charged to the electric furnace, while the fumed slag is tapped into the settling furnace for further cleaning, where matte, slag and speiss (residual metals) are separated. The matte from the settling furnace is also sent to the converters; its speiss is sold to external customers; and its slag is water granulated and sold as construction material, which is known as iron sand."

Jan 1, 2012

By Raj K. Rajamani, James R. Nagel, York R. Smith

In this work, we examine the efficacy of Electrodynamic Eddy Current Separation (EECS) to recover valuable materials from end-of-life solar panels. Traditional rotary-based eddy current separators are capable of excitation frequencies of 1 kHz or less and struggle to economically separate particles smaller than 1 cm. A new design of eddy current separators has been developed at the University of Utah which has no mechanically moving parts. The design is capable of excitation frequencies up to 50 kHz, allowing sorting of particles as small as 1.0 mm. Recently, we have been successful in separating mixtures of Si/Al and CdTe/Al particles (1–3 mm) with recovery and grades greater than 85%, an energy demand of 68 kWh/short ton of sorted material, and throughput of roughly 10 kg/h. Current and future challenges utilizing this method for valuable material recovery from end-of-life solar panels are discussed.

Mar 1, 2017

By I. A. H. Schneiderl

Eichhornia crassipes approaches being a scourge in many parts of the world, .choking waterways and hindering transport upon them. At the same time it is known to readily abstract heavy metal ions from water and, thus, aids in the removal of heavy metals found in such waters. This paper considers the possibility of using specific parts of the plant as an inexpensive adsorbent for the removal of heavy metals from contaminated chemical and mining industry waste waters. In particular the root of the plant was found to be an excellent accumulator of 'heavy metal ions including uranium from solution. It is. also suggested that dried roots of the plant ?might be placed in simple bags and used in a very low cost metal ion removal system.

Jan 1, 1995

By Qingyu Deng, Shiwei Ma, Wang Hua, Guibao Qiu

"The flow properties of the blast furnace slag bearing high TiO2 at high temperature like the viscocity may change a lot due to the formation of the carbonitride inside, causing serious problems on the separation between the metal and the slag. Therefore, the critical condition of the formation of Ti(C,N) in blast furnace is vital importance for the ironmaking process with iron ore bearing titania. In this study, the formation of Ti(C,N) in blast furnace and the influences of various factors on the Ti(C,N) formation are investigated by FactSage. It is found that the mass of Ti(C,N) would reach the maximum at 1480 oC, and the product is mainly TiN below 1620 oC, while it is mainly TiC above 1620oC. The order of the factors by the importance from strong to weak was: temperature, the content of TiO2 in slag, basicity of slag, the content of MgO and Al2O3.IntroductionThe titanium dioxide (TiO2) in iron ore bearing titania will be partly reduced by carbon to titanium carbonitride (Ti(C,N)) in blast furnace, causing serious problems on the separation between the metal and the slag because of the change of flow property. Therefore, the critical condition of the formation of Ti(C,N) in blast furnace is vital importance for the ironmaking process, especially for the smelting of iron ore bearing titania. Extensive experimental data in regard to the formation of Ti(C,N) has been reported in numerous papers[1-6]. However, only some discrete data can be obtained by experiment, and it is difficult to detect the mass of Ti(C,N) in slag. In addition, the experiment is difficult to be proceeded when the temperature is above 1600oC. Therefore, it is very difficult to make clear the critical condition of the formation of Ti(C,N) by experiment."

Jan 1, 2012

By Ruirui Wei, Mingrui Yang, Xuewei Lv

Copper slag is a by-product obtained during smelting of copper from copper ores. In China, for one ton of metal production about 2.2 tons of copper slag was generated, and approximately 15 million tons slag is produced in 2013. Dumping and disposal of such huge quantities of slag will cause environmental and space problems. Most importantly, copper slag cannot be made full use of to maximize its value. In this study, copper slag was used to take the place of scrap iron and part of silica in traditional process and to produce FeSi alloy as the main material. Utilizing silica and copper slag as the raw materials and coke as the reducing agent, FeSi45 was produced in the induction furnace. In addition, the effect of different n(C)/n(O) on FeSi45 has been investigated.Increasing n(C)/n(O) is beneficial to form the stable phase of FeSi. Meanwhile, n(C)/n(O) greatly affects the reduction and recovery of silicon than iron. When n(C)/n(O) equals 1.10, the recovery of silicon and iron is about 77 and 95%, respectively.

Mar 1, 2017

By Dominik Hofer

A broad spectrum of tantalum containing input materials can be processed for the production of synthetic tantalum concentrate (“SynCon”). The use of these low grade substances offers a secure alternative to mining of coltan in Central Africa. SynCon is produced in a multi-stage pyrometallurgical process, wherefore the melting behaviour of slags presents an important factor especially regarding the energy consumption and its optimisation. The characteristics of a slag comprising mostly Al2O3, CaO, SiO2 and MgO are influenced by the amount of other oxidic constituents which enfolds the main focus of this study. A hot stage microscope serves for the investigation of the slag behaviour in a temperature range from 1000 to 1600 °C under reducing atmosphere (CO/CO2 gas). The experimental results are compared with thermodynamic calculations (FactSage) to get a better understanding of the process.

By Petrus Christiaan Pistorius, Farzin Fatollahi-Fard

The production of synthetic rutile—a common starting material for most titanium production processes—from iron-rich titanium minerals such as pseudorutile and ilmenite is described. The process for “upgrading” the mineral to synthetic rutile is by carbothermal reduction of the mineral while immersed in a molten salt at high temperature, followed by magnetic separation of the reduced iron. A variety of factors are also investigated, such as particle size of the mineral, the type of mineral, and the molten salt used. The solubility of iron(III) oxide in different molten salts is also experimentally determined.

Jan 1, 2016

By S. N. Monteiro, E. B. Zanelato, J. Alexandre, M. T. Marvila, A. R. G. Azevedo, G. C. Xavier

One of the parameters used in the study of mortars is the adhesion resistance, which indicate show much the mortar adhered to the substrate. The usual study is done at 28 days, to worldwide standardization. Few researchers study the adhesion of mortars to ages other than 28 days. In this scenario, the adhesion strength tests of conventional mortar with a 1:1:6 mass scale (cement, and sand) at 7, 14, 28, 56, 91, 182 and 364 days were performed in order to understand the behavior of this material. The usual characterization tests of the mortars were carried out to correlate the values obtained with the adhesion results. The obtained results demonstrate that the mortar continues to gain resistance with the passage of time. For the trait studied the gain was considerable, indicating that over time the cement continues to hydrate, reacting and contributing to the strength of the material.

Mar 1, 2018

By Qingguo Xue, Jingsong Wang, Yingli Liu, Guang Wang

In the dropping zone of blast furnace (BF), primary slag absorbing ash of pulverized coal and coke become to be intermediate slag. Due to viscosity and surface tension of slag and the pore between cokes, some slag remained in coke layer and affected the permeability of blast furnace. The flow behavior of slag with different basicity (0.55–1.10) and Al/Si (0.35–0.50) were studied. Meanwhile, the viscosity and surface tension of slag were calculated. The results showed that, with the increasing basicity of slag, surface tension increased and viscosity decreased. With the Al/Si increase, surface tension and viscosity increased. The smallest pore that all slag can pass through was 4.5 mm. However, the height between slag droplets and the bottom of crucible indicated that the ability of slag to pass through pore were weakened with the increasing basicity and Al/Si. Thus, slag which absorbed ash from fuel become difficult to pass through coke layer.

Mar 1, 2017