Search Documents

By J. L. Vanderbeek

The SAG milling of ores with markedly variable grinding rates presents definite process control challenges. Decisions must be made regarding the selection of the most appropriate combination of mill volumetric load level, percent solids, and mill speed for the combination of ore types being processed at the moment. An investigation was performed concerning the effects of these parameters. General results are presented.

Jan 1, 1985

By T. Stack, C. Roos, M. Drake, P. Conrad

"This paper presents the evaluation Montana Tech completed for the Western Energy Company Rosebud Mine relating to the benefits of survey data collected using novel technologies over traditional methods for topographic surveys. These technologies include Unmanned Aircraft Systems (UAS), photogrammetry, and laser scanning/LIDAR. Utilizing these technologies, large areas such as reclamation areas and cast blasts can be surveyed in a timely manner for use by the mining operation. The areas that were evaluated were the improvements in the safety of employees and the time required to collect data. In addition, there is also a potential cost savings for the operation, all while not affecting the accuracy of the data that is collected. PROJECT BACKGROUND Accurate topographic survey data is critical to successful surface mining operations. It is used for mine planning and design as well as permit compliance. Currently, employees typically collect survey data using GPS equipment or total stations. These methods can be dangerous, as they require employees to work near large operating mobile equipment, edge of high walls, and on piles of stacked steep-sloped loose material. Aerial and satellite photographs, performed by a contractor, can be used to obtain some of this information, but it is expensive and may not be attainable during overcast conditions. Montana Tech, along with the Rosebud Mine, conducted research on the accuracy, cost, and other benefits of survey data collected using novel technologies. Some of the methods studied include, but are not limited to, Unmanned Aerial Systems (UAS) or Vehicles (UAV), photogrammetry, and laser scanning. These methods were evaluated to determine if these technologies provide mining companies with a safer, cost effective, and accurate method to collect data for surface mining operations. The project scope was to evaluate various surveying techniques to determine which techniques would be applicable for the Rosebud Mine and complete a trade-off study comparing the new techniques with currently used methods. The trade-off study included an analysis of the technological differences between the methods, safety and legal considerations for the new techniques, operational limits, and the costs associated with each technique. Working with the Rosebud Mine team, techniques were selected for field trial and accuracy comparison. This paper presents a literature review of applicable technical papers and a summary of the Federal Aviation Administration regulations for UAS, followed by a study comparing conventional GPS topographic surveys with UAS based systems and laser scanning systems. The comparison of the various methods was broken into the following four categories: operator safety analysis, time comparison, survey accuracy, and cost analysis. After all of these portions of comparison were completed a recommendation was provided based on the evaluation that was performed."

Jan 1, 2017

By P. R. Taylor

Recent research by the investigators has evaluated the oxidation roasting of refractory gold concentrates in the presence of hydrated lime. (Taylor, 1990, 1991, 1992, 1993). These results have indicated that it may be possible to roast concentrates in such a way as to contain nearly all of the sulfur and arsenic in the roaster calcine and that cyanidation may be possible. To further evaluate the behavior of this type of roasting system a laboratory cyclone reactor was built and operated using pyrite and hydrated lime as a .model system. Approximately 50 years ago, the principle of cyclone firing entered practical boiler construction. The appeal of the cyclone configuration was that it afforded the flash combustion process greater efficiency due to turbulence-induced increased mass transfer, heat exchange, and combustion rates.

Jan 1, 1994

By E. M. Williams

The U.S. Bureau of Mines recently conducted a limited-scope study on the use of lineament analysis and electromagnetic geophysics to better identify the surface expressions of faults at the Cimmaron Mine near Raton, NM, an operating longwall mine in the York Canyon mine complex. Two normal faults were encountered by the mine, one during gate road development and drilling and another only through drilling. The potential ground control problems and offsets associated with these faults will severely impact long-range development plans, so it is essential to know the lateral extent of these faults within the coal reserves. The surface topography at the site is fairly rugged, yet outcrop exposure is poor. There is no obvious visible geologic evidence to indicate that the faults identified at depth extend to the surface. Both the geophysical and remote sensing techniques provided information on the presence and extent of important geologic structures which could not be gained just from drilling and surface outcrops. The geophysical surveys also were invaluable in confirming the presence of subsurface geologic structures in the vicinity of the lineaments assumed to be associated with the faulting.

Jan 1, 1995

By Argenis Gamboa

The Arab community is formed by around twenty countries in Africa and Asia, linked basically by a common language-Arabic - and the same religion, the muslim. They jointly occupy around 12 million square kilometers with a total population of around 140 million people. Nevertheless, these nations differ widely in their geographic area and population. Thus, while Egypt has a territory of over a million square kilometers and a population of nearly 40 million people, Kuwait, Qatar and Bahrain have, among the three of them, less than 30, 000 square kilometers and a million inhabitants. The per capita income also vary greatly, depending on whether they are oil producing countries or not. Generally speaking, it can be said that these countries economies have been based on oil or agriculture and that in these last years, they have been making serious efforts to increase their degree of industrialization and have greatly improved their infrastructure. This trend has resulted in the development of the iron and steel industry, which is still in a stage of primary development.

Jan 1, 1979

By James J. Fallon

Last summer Larry Miller of Roberts & Schaefer told me that his AIME committee would like me to present some thoughts on the marketing of industrial mineral fillers and pigments to this illustrious group in Las Vegas. Shortly after, Brian Coupe of "Industrial Minerals" (the magazine) notified me that I would be presenting a paper to the Fourth International Industrial Minerals Congress in Atlanta this June. It seems to me now it might have been more appropriate to reverse the papers. Las Vegas, a town based on risk, might want to hear what we have to say in Atlanta. The subject for June is "Risk Philosophies of U. S. Industrial Minerals Companies". However, upon reflection, marketing of industrial minerals reflects risk philosophies to a considerable extent, so we'll cut the deck and deal on the subject of marketing.

Jan 1, 1980

By Todd Kilduff, Ryan O’Connell

Pipe canopies continue to gain momentum as a reliable methodology for construction of excavations below critical facilities with minimal surface settlement tolerances, such as railroads or roadways. Two tunnel projects designed by Kilduff Underground Engineering in the Salt Lake City, UT area, each at varying stages of completion, had project design criteria for selection of a tunneling methodology to minimize surface settlement. Both projects consist of a pedestrian tunnel, one crossing beneath a major roadway in downtown Salt Lake City and the second beneath UPRR tracks. Both projects were in difficult, coarse alluvium/fan ground conditions with project criteria that resulted in minimal cover above the tunnel. For each project, a pre-support pipe canopy was designed, requiring the placement of steel, canopy pipes driven the extent of the tunnel length. The pipe canopy is installed using a trenchless technology and then excavated with SEM tunneling and shoring provided by traditional support of excavation methods. The pipe canopy pre-support method offers a low-impact method to install an underpass beneath critical structures by adding significant stiffness to the subgrade to mitigate surface settlement during the main tunnel excavation sequence. These case studies seek to communicate the challenges associated with pipe canopy installation in site-specific ground conditions and explains how these challenges were overcome. This paper aims to define the project risks and describes the pipe canopy methodology as a viable solution to mitigate surface settlement in low cover tunneling scenarios.

Jun 13, 2023

By J. S. Wozek

In metallurgical applications, coal fulfills dual roles as a chemical feed stock and as a fuel source. These applications range from cokemaking, ironrnaking (including pulverized coal injection), foundry, basic oxygen furnace / electric arc furnace coal additions, direct ironrnaking, Corex, and the futuristic direct steelmaking. In all steelmaking related processes, chemical reactions are simultaneously temperature and chemical dependent. Therefore, coals used in these processes must consistently comply with specific quality parameters in order to promote efficient operations. This paper limits discussion of Metallurgical Coal Quality to cokemaking and ironmaking applications. Its purpose is to present the customer's perspective on the control of critical coal and coke properties.

Jan 1, 1994

By B. H. Kim, S. J. Schatzel, K. M. Ajayi, G. S. Esterhuizen, D. W. H. Su, Z. Khademian

The stability of shale gas wells drilled through current and future coal reserves can be compromised by ground deformations due to nearby longwall mining. Depending on the longwall-induced rockmass permeability, the high-pressure explosive gas from the damaged well may reach mine workings and overwhelm the mine ventilation systems. This study uses geomechanical models to estimate the rockmass permeability induced by mining. A two-panel longwall model of a deep, 341-m-cover mining site in southwestern Pennsylvania is constructed in 3DEC to explicitly model the rockmass by a Discrete Fracture Network (DFN) technique. Stress-induced fracture apertures and permeabilities are calculated across the model and are validated against permeability measurements. A Fracture Flow Code (FFC) is developed to use these results to predict potential inflow to the mine should a gas well breach occur. One hundred DFN realizations are simulated, and the results show that for a gas pressure of 2.4 MPa, the average of the predicted inflow rates to this deep-cover mine is 0.03 m3 /s, significantly lower than the average inflow of 0.92 m3 /s for a shallow-cover mine (145 m deep) studied in the previous work (Khademian, et al. 2021). The result can help assess the potential hazards of a shale gas well breach for mine safety and evaluate the ventilation requirements to mitigate the risk

Mar 2, 2022

By C. V. Deutsch, J. B. Boisvert, M. A. Cuba

The amount of information available for characterizing a deposit increases over time due to the continuous acquisition of data during mining. This additional information is collected from different sources, including geologic mapping, production data and infill drilling. Throughout the lifetime of a mining project, the block model and the mining sequence are periodically updated to account for this new data. In general, the acquisition of additional data increases the accuracy of the block model, reduces uncertainty in ore/waste limits and clarifies the optimal mining sequence. There has been extensive research on mine planning, but current techniques do not consider the decrease in uncertainty as additional information becomes available. Conventional paradigms assume either 1) the kriged model is correct and uncertainty due to multiple realizations does not change the mining sequence, or 2) the mining sequence is unrealistically adapted to each realization. A new paradigm is proposed for evaluating minable reserves of surface mining projects, which accounts for the acquisition of additional information in the design of the long term mine plan. Multiple scenarios characterizing the dynamic nature of mining and data collection are created. In the proposed methodology, the performance of the long-term mine plan depends on both mining and data acquisition strategies. Each scenario considers the same extracted volume for the first period, resulting in a set of scenarios that diverge from a common initial period, accounting for how the mine may develop over time as new data are acquired and provide a more realistic evaluation of reserves with an appropriate level of uncertainty. A synthetic example is presented to illustrate the implementation of the methodology and the benefits over conventional paradigms.

Jan 1, 2013

By Alastair R. Biggart

ABOUT BENTONITE TUNNELLING Much has been written and many learned papers given on this subject whose generic term is Slurry Tunnelling. This paper is about the particular form of slurry tunnelling known as the Bentonite Tunnelling System. This method. of tunnelling was invented by J.V. Bartlett of consulting engineers, Mott Hay and Anderson in 1964. The general principles are incorporated in British Patent No. 1083322. It was not until the early 1970's that serious experimental work was started to prove the technical feasibility of the process. In the U.K. in 1971 Edmund Nuttall Limited started on an experimental length of 3.8m diameter tunnel at New Cross in London. In Germany at about the same time Wayss and Freytag were starting on a 3.7m diameter collector sewer tunnel in Hamburg. In Japan early slurry tunnelling work was carried out in the 1960's. In the early 1970's a large number of slurry tunnels of various diameters were carried out in that country. This paper is being presented at a time when this system of tunnelling has become an accepted method throughout the developed world. As a result of the work carried out so far there is now a large amount of data existing regarding the effects on the ground in the immediate area of the tunnel, settlement at the surface and the ability of the system to cope with ground varying from clays to coarse gravels and containing large erratics such as granite boulders. The decade of the 1970's has therefore seen a very rapid pace

Jan 1, 1979

By D. C. Rotherham

The Kidston gold discoveries were originally made about 1907, and by 1934, 1.76 Mg (62,000 oz) of gold had been produced from placer and lode mining of higher grade, most¬ly oxidized gold ore. As mining in the lode ore penetrated deeper, costs increased and the world gold price stagnated. The lode or underground production averaged close to 6.9 g/t (0.2 oz per ton) Au for the 201 kt mined. No mining or development took place from 1934 until 1965. Kidston's high grade ores were exhausted by 1934. From 1965 to 1976, exploration had developed 3 Mt of about 3 g/t (0.88 oz per ton) Au. Placer Pacific acquired rights to the property in 1976 and began a geologic and engineering study of the district. It was clear that the deposit had the potential for becom¬ing a large-tonnage, low-grade producer. However, explora¬tion had to discover the tonnage and grade and engineering needed to solve the obstacles of production costs. Bulk material handling problems were addressed by Placer's wide experience in open pit mining, and the increase in work index accompanying deeper ores was handled by Placer's metallurgists. The matter of power for the operation was solved by engineering studies. These showed that power could be generated and brought in economically. The price of gold also increased after 1976, and this helped in the economic analysis. The Kidston discovery since 1976 is really a combination of good exploration geology and careful engineering plan¬ning that overcame the obstacles presented by ore characteris¬tics and the location of the deposit. The attached paper by Harry Mustard is an extract of his honors thesis and explains the deposit geology.

Jan 1, 1990

By Mark J. Logsdon, Barbara Basse

Mississippi Valley Type Pb-Zn deposits are widespread in the midcontinent U.S. and have been mined from the 1800's to present. Some tens of thousands of acres of mined land in the Tri-State District have been designated as Superfund sites as a result of surficial mine wastes and ground waters with elevated levels of metals. EPA considers the surficial mine wastes to be hazardous and a major source of acid mine drainage fAMD) that degrades water resources and threatens human health and the environment. To mitigate potential risks at one site near Galena, Kansas, a group of mining companies who had been identified by EPA as Potentially Responsible Parties IPRPs) proposed subgrade disposal of the mining wastes in shafts and subsidence features. However, this proposal was challenged by the Agency on grounds related to AMD and the potential for degradation of ground water quality. The PRP team developed a program of materials characterization, laboratory-scale leaching, and finally large-scale, pilot testing in the field. Static and dynamic leaching tests at both laboratory scale fusing artificial rainwater under both variably and fully saturated conditions) and field scale (using pH 4.5 ground water) showed that the surficial wastes do not produce acidic leachate and are not a long-term source of metals. Laboratory chemical and mineralogical tests show that the mine wastes contain substantial carbonate, but very limited iron sulfides, consistent with the leach test results. EPA "characterization" tests fEP Toxicity and TCLP) compare very poorly with tests simulating the expected leaching conditions. While these tests would classify the surficia1 wastes as "hazardous, they do not characterize the behavior of the high-volume, low-concentration, coarse-grained materials with respect to environments and disposal options of interest. To be meaningful, characterization of mining wastes must be performed in a manner that simulates the environmental conditions that are actually of interest with respect to a specific decision, such as subgrade disposal in the saturated zone.

Jan 1, 1991

By G. Pan

The production data of many mines have not reconciled geostatistical estimations based on exploration and development drilling. The discrepancies in recovered metals are sometimes as large as 30%. A number of factors are responsible for such unpleasant outcomes. A major cause, however, is the lack of geological controls in the implementation of geostatistical techniques. Geological modeling establishes geological constraints and mineralization/ore envelopes. Geological constraints are usually established through drill hole interpretation. Mineralization and ore envelopes have been delineated manually based on assay grades. The issues associated with manual methods are: •Time requirements . •Inconsistent dilution. •Uncontrollable implementation variance. Although the time issue may not be a big concern for some companies, the other two have been responsible for many undesired estimation errors. A new geostatistical approach described in this study is designed on the basis of indicator and ordinary kriging. The central component of the method is the procedure for automatic delineation of mineralization and ore envelopes. The method, referred to as probability assigned constrained kriging (PACK), is demonstrated on a Carlin-type gold deposit. The estimation results are compared to blast-hole based production panels, showing that the estimated tonnage is about 2.1 % higher than the actual production, and the average grade is about 2.4% lower.

Jan 1, 1995

By P. James, L. J. Steiner, F. Turin

NIOSH researchers and an industry partner conducted an investigation to study the effectiveness of ergonomic interventions in mining. The study required a significant commitment of time and resources from the cooperating site, Bridger Coal Company. This paper focuses on some of the challenges faced by the researchers and their cooperator. Challenges included the need to redesign methods of identifying and prioritizing injuries, and the need to train the workforce in ergonomics while still maintaining progress and interest in the process. The authors discuss some practical interventions implemented by Bridger Coal to date, and discuss future research implications brought about by PacifiCorp’s Generation Business Unit, who monitored the project to determine whether an employee-owned ergonomic process could be implemented throughout their operations.

Jan 1, 2003

By M. A. Pipke, C. M. Brown

The semiautogemus grinding circuit at the Utah Mines Ltd., Island Copper operation, located on Vancouver Island, British Columbia, is described. Since startup of the operation in 1971, grinding circuit throughput has been progressively increased from the initial design rate of 90 000 (99,000) to the current average 45 000 t/d (49,600 stpd) of porphyry copper ore. Key developments ad modifications in operating and maintenance practice that have contributed to this increase are reviewed.

Jan 1, 1987

By Terry Owen

Business development process. Throughout Cyprus Amax's early months in Russia, the company stayed focused on what was needed from a deposit for economic success. Cyprus Amax's reason for success in Russia is that all involved - its Russian partners, the workforce and expatriates - provided a focused effort that served the project as it worked through the tender process and the Russian regulations. The company developed an understanding of the regulatory process by working with solid, ethical partners. Infused into the Kubaka management structure were Russians with the knowledge to facilitate the process and a professional group of expatriates. Developing credibility and a solid rapport with the Russian mining authority was critical to the success of this venture. Identifying and gaining the trust of key Russian individuals was also critical during the early stages. Gaining their trust and building credibility was part of the process. These key Russians were brought to the United States to visit existing Cyprus Amax mines. These efforts proved valuable in building an understanding with the Russians about the kind of company Cyprus Amax is and the kind of efficient operations that it can run. This was a learning process for all parties. Fortunately, the company was dealing with intelligent and educated people.

Jan 1, 1997

By Gunnar Nord, Per-Anders Persson, Duri Prader

The paper gives a short resumé of the findings of the joint US - Swedish "Mechanical Boring (MB) or Drill and Blast Tunneling (DB) ? Workshop" in Stockholm December 1976. New developments and trends in both MB and DB techniques in Europe since 1976 are described, and information is given on some interesting new projects. Differences in contracting principles between the US and Europe lead to different practices for preinvestigations, design, excavation and arbitration and legal affairs. It is shown that this often leads to a higher cost in the US than in Europe for similar excavation jobs. A typical US tunnel job also has more men on the site than a similar job in Europe. This adds to the cost difference and is only partly balanced by a slightly higher rate of excavation in the US. A comparison is made between two quantitative methods of predicting MB penetration rates. These are in reasonable agreement. A probable future development in machine design is an increase in cutter load towards perhaps 25 tons per disc where the tunnel diameter is large enough to house the machine size dictated by the size of the very large electric motors required. Recent European developments in drill and blast technique include improved methods for cautious blasting, precision hydraulic drilling of small diameter holes, and non-electric interval blasting techniques. These developments still keep the drill and blast method ahead of mechanical boring costwise for tunnels in igneous rock whereas for most sedimentary materials mechanical boring has a lead, particularly for long tunnels.

Jan 1, 1979

By Jennifer Gallagher

The Henderson molybdenum mine, near Empire, CO, has operated since 1976 using a panel caving process and a rail haulage transportation system. After two decades of service, the rail haulage system required a substantial capital expenditure to improve operations. The timing for this worked well because Henderson was able to combine this capital need into a mine plan that addressed process bottlenecks and current mining practices as a new production level was designed and developed. This process was a logical step, following an equipment upgrade program, and became known as the Henderson 2000 project. One of the key components of Henderson 2000 is a new ore transportation system. Throughout Henderson's life, the bottleneck has been the rail haulage system. Henderson staff evaluated several transportation alternatives and decided on a truck haulage configuration feeding an underground crusher and conveyor system. This configuration will eliminate the haulage bottleneck and will allow the mine to increase capacity. The installation of this system will be completed by the year 2000. The second key component of Henderson 2000 is the development of a new 7175 production level to extract the lower reserves of the ore body. Henderson staff benchmarked other caving operations and compared their mining practices to Henderson's basic mining guidelines. It became apparent that Henderson's practices could become more efficient, particularly in the areas of drawpoint spacing and column heights. These concepts were incorporated into the layouts

Jan 1, 1998

By Michael J. Mankosa

Increased emphasis has been placed on recycling consumer and industrial waste products. This trend has created a new industry that is focused on recovery/ separation of byproducts from waste material. As a result, interest has increased in the development of separation systems designed for the recycling industry. Much work has been done in this area. However, existing techniques developed for minerals beneficiation are often ignored. An example of is the foundry industry. There are currently more than 3,000 foundries in operation throughout the United States. Each consumes between 9 and 900 t/d (10 and 1,000 stpd) of sand for mold production. Either silica, chromite or zircon is, used in various combinations with chemical or clay binders. After casting, the sands are typically discarded into a landfill. This practice has become an environmental concern, especially the disposal of chromite and zircon. Silica sand is not environmentally sensitive. But it is used in greater abundance (6 to 7 Mt/a or 6.6 to 7.7 million stpy)and thus has prohibitive haulage and landfill costs. Current technology for sand reclamation involves thermal treatment to remove residual binders followed by dry mechanical attritioning (Leidel, 1993; Klein, 1994). This approach results in high losses due to fines generation and high costs associated with thermal treatment. As a result, this approach has shown only limited success. Stringent regulations are also affecting the disposal of secondary materials, such as plastics and metals. This is particularly true for the ferrous and nonferrous scrap metal industry. It plays a major role in industrial recycling of steel, aluminum and copper. Applications such as wire recycling present challenging problems since a hazardous byproduct (plastic insulation) is generated by the recycling.

Jan 1, 1997