Search Documents

By S. Usui

In a previous article1 the methyl stretching vibrations for a series of xanthates and amines were reported, and the frequency of the methyl stretching vibrations in a homologous series of the alkyl compounds were shown to decrease exponentially with chain length and approach a limiting value corresponding to that of saturated hydrocarbon beyond six or seven carbons. These observations were explained quantitatively by the theory of Goto and Takenaka2 who proposed an equation relating the frequency shifts to the inductive effect of polar groups. As a result, the alkyl groups in the shorter chain heteropolar compounds were interpreted as becoming somewhat polar, and a good correlation was observed between the CH3-stretching frequencies and such surface chemistry parameters as contact angle, surface tension lowering, solubility, and critical micelle concentration" The substitution of fluorine atoms, the most electronegative of all atoms, for the hydrogen atoms in alkyl groups was expected to reverse the direction of the inductive effect within a heteropolar molecule, and its effect on the C-F stretching frequency shifts and on some surface chemical properties became of interest. In a recent study the C-F stretching frequencies of a series of normal perfluorocarboxylic acids and a few 1,1' -dihydroperfluoro alcohols were determined as a function of chain length and the results were compared with the corresponding hydrocarbon analogs. Furthermore, the nature of the induced polarity in the hydrocarbon and fluorocarbon groups was investigated through surface potential measurements at the interfaces of air-aqueous solutions of normal butyl alcohol and of l,l'-dihydroperfluorobutyl alcohol and through differential capacity and electrocapillary measurements at the interfaces of mercury-aqueous solutions containing the above two alcohols. Experimental Normal perfluorocarboxylic acids and 1,1' -dihydroperfluoro alcohols were provided through the courtesy of the 3M Company, St. Paul, Minnesota. Normal butyl alcohol was purchased from Distillation Product Industries, Rochester, New York. A Perkin-Elmer Model 621 infrared spectrophotometer was used to investigate the spectra in the frequency region of 1200 to 1270 cm-l with frequency scale

Jan 1, 1971

By S. R. Stine

The Cyprus Thompson Creek Mine is located at 2,286m (7500 feet) elevation in the Central Idaho mountains, 61.16 kilometers (38 miles) southwest of Challis, Idaho off State Highway 75. The Thompson Creek molybdenum deposit lies near the eastern border of the late Cretaceous Idaho Batholith within a complexly deformed sequence of Paleozoic sedimentary rocks. Molybdenum mineralization is contained in a composite biotite granodiorite-quartz monzonite stock considered to be genetically related to the Idaho Batholith intrusive event. The ore is being mined by open pit methods and delivered to the concentrator stockpile with an overland conveyor belt system. The concentrator is designed as a 22,680 metric tons (25,000 ton) per day plant at an average head grade of 0.1% Molybdenum.

Jan 1, 1986

By I. M. Arbuthnot

Over the last five years, a large number of small to medium sized carbon-in-pulp gold treatment plants have been built in Australia, most designed to treat between 250,000 -1,500,000 tpa of ore. In many cases, the primary requirement was to get a plant built and operating in a short period of time and at minimal capital cost, relating to the limited capital resources and tight cash flow positions of these relatively small mining companies. Since the inclusion of both pre-leach and tailings thickeners resulted in an obvious and significant capital cost, most plants were built without thickeners, without doing a detailed cost-benefit analysis on their inclusion, However, the increasing use of High Rate Thickener?s (HRT s) in the mineral processing industries resulted in a reassessment, in some cases, because of their considerably lower cost. This reassessment was triggered primarily by the need to conserve water in arid mining areas, where borefields were costly to install and water was limited. It has become apparent, though, since startup and operation of these installations, that the savings in cyanide consumption is also a very significant factor and can be used as a primary justification for the installation of a HRT in many cases.

Jan 1, 1991

By G. R. Giuliani

Hanna Mining Company's Groveland Mine is located in the Upper Peninsula of Michigan. The low grade iron ore deposit consists of a mixture of magnetite and hematite with chert, jasper, quartz and various iron silicates (1). The ore is beneficiated by magnetic separation and anionic flotation of the iron minerals with chemical depression of the silica. The magnetic concentrate makes up about 75% of the concentrate. The concentrate is pelletized at the rate of 2.0 million LTPY of pellet production. The concentrator facilities were started up in 1959 and the concentrate was marketed as sinter feed until 1963 when the concentrator was expanded and the pelletizing plant was added. The pellet plant now consists of regrinding, elutriation, filtering, balling and induration. The pellet machine is a straight grate which employs updraft drying and cooling and downdraft drying, preheat and firing. It is necessary to regrind the concentrate before pelletizing. The con-centrate is 60% passing 325 mesh, with a surface area of ±lOOO cm2/Gm, and must be ground to about 83% passing 325 mesh, 1600 cm2/Gm blaine surface area, for pelletizing. The energy for regrind has been reduced from 12.5 KW per LT to 8.80 KW ate of 2.0 million per LT. This was the result of changes made in the concentrator where originally a coarse spiral concentrate, instead of the magnetic concentrate which is screened on fine screens to reduce the coarse fraction and prevent overgrinding before flotation, was produced. Also in 1968 an additional concentrating line was added to the concentrator which employs more grinding power than the other three lines. The demand for a high iron grade and lower silica pellet resulted in the investigation of different schemes of upgrading the reground concentrate which had more iron values liberated during grinding for surface area. The reagentized material presented many problems, mainly in selectivity trying to flot the iron and with high reagent consumption having to dereagentize the concentrate for amine silica flotation, in the various flotation systems tried. Tests were then conducted with elutriation (2) which proved satisfactory by removing the lower specific gravity, fine gangue material from the heavier material with the

Jan 1, 1977

By Michael Lenz

Predictive maintenance technologies including vibration analysis, tribology, infrared thermography, ultrasonic detection, and electrical measurements have been applied to large electric mining shovels. The predictive program was initiated on the P&H Model 2300 and 4100 electric shovels. The utilization of these technologies has shown the potential for improving electric mining shovel availability and minimizing maintenance costs. Predictive technologies provide the tools to assess machinery condition. Availability is enhanced by the condition based planning of component replacement. Maintenance costs are minimized by focusing resources through condition based prioritization.

Jan 1, 1997

By Pascal Deschamps

"INTRODUCTION During the last decades, many underground facilities for the storage of hydrocarbons have been excavated worldwide and the technology is fully mature. Similarly to other underground structures, the initial basic design has to be adapted along with the work progress, in order to cope with the actual site conditions and in particular the geology, hydrogeology and associated rockmass quality. In addition, Client’s or underground Contractor’s constraints (such as resources availability, schedule or cost impact) may vary from design to construction and require last minute adjustments. Engineers are required to introduce flexibility and anticipation of unexpected situations (similar to the above-mentioned) while conceiving large underground facilities. Although most of the cases require only minor adaptations, crucial parts of the facility have sometimes to be considerably modified and reviewed. This article will present four cases evidencing how the design of one of these essential structures - the concrete plug – has been adjusted during site implementation without impairing the initial performances. Hydrodynamic containment The product containment of the unlined caverns discussed here is ensured by the principle of hydrodynamic containment. A permanent water flow is naturally or artificially maintained with an orientation toward the storage cavern and then, neither product-tight membrane nor lining are required. The hydraulic gradient (and the associated water flow lines), being directed from the surrounding mass toward the cavern, prevent from outward migration of the product. If the hydraulic gradient is not sufficient or if the water table is evidencing instability, water can be artificially injected into the rockmass through purpose-built boreholes, drilled from dedicated galleries. This water injection system, called the water curtain, is generally located several tens of meters above the level of the cavern. This principle is illustrated here after."

Jan 1, 2016

By K. H. Nimerick

Laboratory data and field tests indicate that substantial losses of valuable coal can be caused by wind erosion. Wind tunnel tests show the effects of wind velocity and particle sizing on the amount of coal lost while in transit. Different coals were evaluated to determine the variables associated with wind erosion. The erosion losses can be substantially reduced by using a binder, or crusting agent, to consolidate the surfaces of the coal into a solid mass which resists erosion. This not only reduces economic loss but minimizes pollution.

Jan 1, 1977

By Sidney V. Gold

Should Gold Producers Hedge Their Positions Through : Sales on Forward Markets? Purchases of Put Options? Sales on Spot Market? Forward Markets Assumptions 1. Producer has a known amount of Gold to sell in year ahead. 2. Effect on price is the same whether sold Forward or Spot Market. 3. None of us have knowledge of Future Price Trend. 4. Contange Market prevails in which Forward price premium is approximately equal to rate of interest.

Jan 1, 1983

By M. L. Young

Hindered settling columns are used throughout the minerals industry for both size and density separations. In this study, the performance of a continuous, laboratory-scale hindered-settling column was evaluated for various particle systems. The test variables included solids composition, water rate, and column height column performance was evaluated using partition curves and corresponding performance parameters.

Jan 1, 1999

By S. Tuylu, D. Adiguzel, A. Bascetin

"In recent years the fact that mining tailings cause serious environmental problems resulted in increasing number of studies about their disposal, storage and usability in various areas. Therefore the new studies about using the tailings for some purposes such as using in shotcrete or producing concrete have been increasing recently. The study is focused on applicability of tailings for producing shotcrete. Under this scope it is considered that mining tailings can bring many advantages in case of that they are used instead of sand, silt or fine aggregate in shotcrete applications. Most important advantages can be listed as decreasing shotcrete cost, decreasing amount if mining tailings to be disposed and the contribution to be provided on sustainable production of sources. The main objective of this study is the investigation of using mine tailing instead of fine aggregate in shotcrete. In this study, 10 shotcrete designs in different proportions were formed, and properties of the mixtures were identified. Then, the experimental results were statistically analyzed, the effects of the amount of the tailing material used on shotcrete properties were presented, and empirical approaches that can be used for the estimation of these properties were developed. INTRODUCTION The disposal of high amount mine tailing on the surface is caused a lot of problems in terms of environmental impact. Unfortunately, it is known that classic disposal techniques such as tailing dam cannot provide a solution these problems. The tailing dams which are usually used in the disposal of mining tailings bring along many problems in terms of cost, environment, and human health. So mine tailings are used in different production such as shotcrete. This technique is becoming increasingly common during recent years. The usability of mine tailings in brick and concrete production instead of cement and fine aggregate has been studied by many studies [1-4]. This situation has been promising for the usability of tailings in shotcrete which is commonly used for ground support especially in tunnels. Shotcrete (sprayed concrete) is applied mainly for construction of tunnels, shafts, renovation works and strengthening of slopes. Main advantage of shotcrete is fast development of strength, which quickly ensures stability of strengthened structure [5]. Shotcrete can be defined as spraying the grout consisting of water, aggregate, cement and optional additive mixture on the desired surface with a compressed air. According to the definition of the American Concrete Institute (ACI), it is the spraying of sprayed grout or concrete on a surface at high speed with air pressure [6]. In recent years, the use of shotcrete for the support of underground excavations is decreased in the mining industry. The design of shotcrete support for underground excavations is a very imprecise process. Strength and pumpability properties of shotcrete are very significant for determining suitable shotcrete design. Flow characteristics of the shotcrete must be determined for pumpability and fluidity of the material."

Jan 1, 2017

The surface properties of eight coal samples were studied by measuring contact angles, coal oxidation, equilibrium moisture and film flotation. The penetration tests were carried out with do de cane, while dodecane and MIBC were utilized in batch flotation tests and in the simplified release analysis. Coal floatability results from the properties of coal organic matter and coal liberation. While the wetting of coal by water seems to be determined by the surface properties of coal organic matter, wetting by hydrocarbons correlates very well with the content of coal mineral matter.

Jan 1, 1992

By D. S. Kimbal

The McCoy/Cove mine is located 48 km (30 miles) south of Battle Mountain, Nevada, USA, in the Fish Creek Mountains at an elevation of 1548 m (5080 ft), see Figure 1. Joseph H. McCoy first discovered gold at this location in 1914. This discovery led to the Gold Dome Mine which produced the first gold from this area in 1928. After the Gold Dome era, the land remained relatively dormant until Houston oil and Minerals Corporation purchased the claims from the Summa corporation and defined an ore body at the present day McCoy pit. In 1986 Tenneco Minerals (formerly Houston oil and Minerals corporation), sold the McCoy mine and adjoining claims to Echo Bay Minerals corporation. The Cove ore body was discovered soon after the sale to Echo Bay. Echo Bay expanded the heap leach operation and built the present mill which began processing ore in the fall of 1989.

Jan 1, 1993

By L. B. Phelps

Industrial mineral production is basic to life in these United States. Production techniques of these minerals are part and parcel of the training that mining engineering educators must, and do, impart to their students. This paper deals with the basic mining engineering program required by all accredited engineering schools and the specific way the Pennsylvania Scare University presents and builds upon them. The manner in which these concepts provide the student with the necessary tools to function as a mining engineer in me realm of industrial minerals extraction is discussed.

Jan 1, 1981

By Frank Cook

As in other areas of the country, surface coal mine productivity in the Central Coal Province--primarily Illinois, Indiana, and west Kentucky--has declined steadily since 1969 (figure 1). Productivity, as measured in tons of clean coal produced per man-shift, dropped 35 percent during the period 1969-1975. Unwelcome at any time, this phenomenon is particularly untimely now, when increased coal production is a national goal. The U.S. Bureau of Mines has been working with the coal industry to develop new operating methods and equipment to enable increased productivity and improved reclamation performance in surface coal mining. Several projects have involved identification and evaluation of existing overburden handling and reclamation practices, and development of means to improve operational procedures. Some results of one of those projects, as they apply to the Central Coal Province, are summarized in this paper.

Jan 1, 1977

By Jaime Adasme, Héctor González, Benjamín Celada

"INTRODUCTION Santiago de Chile is a 7 million inhabitant city which has a 103 Km long subway network operated since 1975 by Metro S.A. This network is used on a daily basis by 2.3 million people. In 2012 Metro S.A. started the biggest enlargement of the network in its history, through the design and construction of the new Line 3 (21.7 Km) and Line 6 (16.5 Km). The detailed engineering contract for civil underground works of Line 6 (L6) was awarded to the Consortium integrated by ZAÑARTU Ingenieros Consultores and GEOCONTROL S.A., in which Geocontrol was in charge of the design of 11 stations and 14.5 Km of tunnel. L6 crosses L3 in Ñuble and Ñuñoa Station, L2 at Franklin Station and ends, intersecting L1, at Los Leones Station as shown in Figure 1. LOS LEONES STATION DESIGN Location and Characteristics Los Leones Station is placed at the North end of the L6, next to the same named station of the L1 and it has four construction units, as is shown in Figure 2: I. Access Shaft (49 m x 47 m). II. Access Gallery (34 m long). III. Station Tunnel (120 m long). IV. Connection Gallery with L1 (104 m long). A singular feature of Los Leones is that the western section of the station tunnel, built from the access gallery, is located below an underground parking lot which is located in Providencia Avenue, as shown in Figure 3. It is important to highlight that the distance between the vault of Los Leones Station Tunnel and the foundations of the underground parking lot is only 6 m."

Jan 1, 2016

By N. Nemeth

The filter is an apparatus designed to hold the filter medium. At such a medium takes place the entire liquid-solid or gas-solid separation process. Hence, the medium is really the essence of filtration. Yet, the medium, an originally clean porous substance with trapped solids in it, is perhaps the most neglected part of filtration research. Basically three problems prevail at the medium: 1) Penetration of solids and their blinding of the medium and the influence of such blinding on the resistance to flow. ii) The behavior of the medium in long term repetitive filtration. iii) The filter effect phenomenon whereby the flow rate on filtering an apparently clear liquid through a medium decreases with time. This study undertakes to investigate these fundamental processes.

Jan 1, 1968

By C. T. Aimone-Martin

Time-domain reflectometry (TDR) laboratory experiments have been conducted using cylindrical salt cores from the Waste Isolation Pilot Project (WIPP). TDR has been used as an instrumentation technique to quantify the type and magnitude of rock mass deformation. Laboratory shear and tensile tests were conducted to calibrate measured deformation versus changes in reflected waveforms. Coaxial cables grouted within rock cores were crimped to produce localized reference defects. The evaluation of waveform characteristics produced during rock deformation experiments shows a good correlation of cable response to both shear and extension of the salt

Jan 1, 1994

By A. D. Davis

This project took a watershed approach in the evaluation of water-quality impacts from past mining activities and current restoration projects in the Bear Butte Creek basin, a small and well defined drainage in a heavily mineralized area of the northern Black Hills. The basin contains numerous inactive and abandoned mines as well as a currently active heap-leach surface gold mine. Bear Butte Creek normally loses all of its discharge to sinkholes in the Madison Limestone aquifer and thus can affect the water quality of this regionally important water resource. Water-quality data were analyzed, stream surveys were conducted, and two abandoned mine restoration projects were monitored to evaluate the effectiveness of the watershed approach and to identify practical remediation techniques that could be applied to other watersheds. A geographic information system (GIS) was developed to organize information on stream quality, abandoned mine locations, and other geologic and hydrologic data. The watershed approach toward assessing and reclaiming abandoned mines appears to be effective when compared to a point-source approach that might improve water quality at specific sites but not result in significant overall improvement to the watershed because of adjacent sources.

Jan 1, 1997

By Downing Terry L.

Dry mineral beneficiation methods have been developed for separation of borate minerals from montmorillonite claystone gangue. The methods include the use of newly developed dry high intensity magnetic separators. The application of these methods has the potential for economic benefit at U.S. Borax Inc. in three areas: ? Processing surface impoundments (ponds) material. ? Pre concentrating ore to be fed to primary refinery. ? Concentrating borate minerals to produce potential products.

Jan 1, 1995

By W. T. Caneer

Uranium may be in short supply due to the predicted energy needs in the coming years. As a result of this a new surge of uranium exploration is underway. The refinement of numerous exploration techniques has accompanied this surge. One such technique is the monitoring of radon gas in surface soils and rocks as a guide to subsurface uranium deposits. The Colorado School of Mines Research Institute became involved in radon studies in 1967 on a project for the AEC. Since that time the Institute has conducted numerous radon surveys for a large number of companies which have been active in uranium exploration. The objective of this paper is to relate the techniques utilized by the Research Institute and the results of some of the studies performed. Most of the studies performed by the Research Institute were related to roll front, sandstone -type uranium deposits. However, we have performed radon studies in various other types of rock. For those who may not be familiar with the application of radon ?sniffing" in soils and rocks, a brief descriptive background should be given. The following question may be asked -- why use radon as a guide to uranium mineralization? Some of the answers to this question are as follows:

Jan 1, 1974