Search Documents

By Robert A. Blake

Introduction Sulfide copper, zinc and iron concentrates are recovered in the 5000 ton per day flotation plant operated by Cities Service Company at Copperhill, Tennessee. The heavy-sulphide ore is first ground to 50 pct. minus 200 mesh and a bulk concentrate floated. The bulk concentrate, over 60 pct. of the ore weight, is reground to 72 pct. minus 200 mesh and then treated in a selective flotation circuit to recover copper and zinc concentrates. The tailing of selective float is the iron sulphide material source for the manufacture of sulfuric acid and iron sinter. The valuable minerals in the ore are chalcopyrite, marmatitic sphalerite, pyrite, and pyrrhotite. A typical mineralogical analysis will be found in table 1. A typical material flowsheet will be found in figure 1. Shown in the flowsheet are a scavenger float on the bulk rougher tailing and a copper-talc separation unit. At times a lead-copper separation circuit has been run.

Jan 1, 1971

By G. W. Phelps

This discussion deals with the geology o£ the Tennessee-Kentucky ball clay deposits; their mineralogy and chemistry; methods of finding, mining and refining; and makes observations on reserves of and future prospects for these clays. Ball clays appear in ceramic formulas for manufacture of vitreous china sanitary-ware, electrical porcelains, floor and wall tile, dinnerware and artwares(l). This type of clay is used for refractory (2) and abrasive products(3), and as a suspending agent for ceramic glazes(4), engobes(5) and porcelain enamel slips(6). Although some ball clay is imported, probably 85-90 percent of ball clay used in the USA(7) is obtained from deposits in Weakley, Henry and Carroll Counties in Tennessee(8), and in adjacent Graves County, Kentucky(9). The term "ball", as applied to clay, probably derives from former mining practice in England whereby conveniently-sized blocks of clay were cut from moist clay beds by spading(10), The expression "ball" has no other technological significance. ASTM(11) defines ball clay as "a secondary clay, commonly characterized by the presence of organic matter, high plasticity, high dry strength, long vitrification range, and a light color when fired." This, and similar(12) definitions, applies to English ball clays but is not satisfactory for many American ball clays. Geology of the Tennessee-Kentucky Ball Clay Deposits Figure 1 shows that most commercial clay areas of the eastern United States lie near the edge of the Coastal Plain; a skew-shaped configuration of its landward boundary outlines the Mississippi Embayment(13), Near the apex of this basin a broad plain, with a rolling, Bullied topography(14), dips gently westward from the Tennessee River to bluffs at the edge of the Mississippi River flood plain.

Jan 1, 1972

By P. Zhang

Phosphate mining in Florida generates approximately 100,000 tons/day of phosphatic clays (slime). This waste slime not only creates one of the most difficult disposal problems in the mining industry, but also causes tremendous loss of P2O5. About 20-30% of the phosphate mined end up in phosphatic clays. Recovering the phosphate from this waste is difficult for two main reasons: 1) the slime is extremely fine in size, and 2) clay minerals account for almost half of the material. A half dozen dispersants were evaluated for keeping the clay minerals suspended for subsequent separation from non-clay minerals by either settling or cycloning. The separation efficiency and economics are discussed.

Jan 1, 1998

By O. Salami, G. Xu

Fire accident is one of the most classic safety concerns in underground mines both in the USA and abroad. It may occur from pool fires due to leakages in hose or pipes, vehicle fires, or fires in tires and conveyor belts in the underground mines. It may also result from the storage of flammable materials such as gasoline, diesel, and explosives in the underground. When fire occurs in an underground mine, it releases heat, smoke, and other toxic gases such as carbon monoxide, and methane to the surrounding thereby making life unbearable to the miners. Furthermore, smoke greatly impact visibility in the underground which makes evacuation even more onerous and challenging. To this end, a thorough investigation of fire behavior and spread of toxic gases in a practical underground mine is imperative to develop a reliable emergency evacuation plan in an event of fire disaster in the underground mine. The objective of this study is to investigate temperature variation and CO spread along mine airways by conducting full-scale fire experiment in the underground mine. The results presented from this study are crucial to developing evacuation plans in underground mines. In addition, the findings from this study could be used to validate existing evacuation models.

Mar 2, 2022

This paper examines the feasibility of combining network modeling and computational fluid dynamics for modeling of underground mine ventilation systems. Both simulation methods have specific advantages and disadvantages for analysis of mine systems. Network modeling is widely utilized by many operations and allows for assessment of current systems and simulation for planning purposes. Alternatively, CFD has been utilized only marginally by operations and is typically a research tool, requiring considerable computational power, complex models, and careful analysis and calibration of results. Network modeling allows for a holistic approach to the ventilation system, giving quantity, velocity and pressure in every branch, but CFD modeling can resolve the flow regime in 2-D or 3-D, which is idea when examination of an area on a more detailed basis is useful, such as dust and gas control. Integration of the two can allow for more flexible systems analysis. The feasibility of integration, along with application to limited underground mine data are examined.

Feb 23, 2014

By W. C. Brice

A cooperative study was undertaken by representatives of the environmental community, the mining industry, and state government to identify and resolve environmental issues associated with base and precious metal mining in a neutral atmosphere before a commercial mining development is announced. The study included testing Minnesota's as-yet-untried non-ferrous mining regulatory program using three hypothetical mining developments sited in environ-mentally sensitive areas where future mining could occur. Results include identification of critical paths for regulatory decision making, identification of particularly sensitive environ-mental issues that will need continued deliberation before resolution, and characterization of data necessary for environmental review and permitting decisions.

Jan 1, 1990

By A. J. Getz

The paper reviews the status of the major precious metals projects in Australia, Papua New Guinea, Indonesia, the Philippines, and New Zealand. The projects may be at the stage of exploration, development, operation, or expansion. The paper covers project location, reserves, method of resource exploitation, anticipated production, and other unique conditions.

Jan 1, 1990

By R. Hogg

A standard procedure for determining size-specific gravity distributions of fine coal (including the -400 mesh fractions) by sieving and centrifugal sink-float separation is described. The significance of using a centrifugal sink-float technique and the effect of the magnitude of the centrifugal force on the separation of fine coal are confirmed in the present study. The relative merits of cumulative versus incremental sink-float are discussed. The procedure is evaluated quantitatively using data obtained for the products of froth flotation of -100 mesh coal.

Jan 1, 1994

By James S. Browning

Extensive deposits of kyanite occur in the southeastern United States, The reserves of these deposits, if developed, are adequate to supply the United States with 35-mesh kyanite concentrate:; for many years at the present-rate of consumption, According to Espenshade and Potter,1 the kyanite-quartz rock type deposits in this area contain about 100 million tons of ore averaging 10 to 30 percent kyanite. The tonnage of kyanite-bearing gneiss and schist is, much larger than the tonnage of kyanite-quartz rock, but the kyanite gneiss and schist are appreciably lower in grade. The largest deposits of kyanite-quartz rock are in the Farmville district, Virginia, and Kings Mountain district, North Carolina South Carolina, and at Graves Mountain, Georgia. Of the known deposits, only four were being mined for kyanite in 1967. These deposits are near Farmville and Dillwyn, Va., Clover S. C., and Washington, Ga. Production of kyanite and synthetic mullite increased substantially in 1965.2 Output of, domestic kyanite concentrate increased by 14 percent in 1965, establishing a record high for the fifth consecutive year. Estimated annual consumption of kyanite minerals and synthetic mullite was in excess of 100,000 tons. The manufacture of mulatto refractories accounts for most of the kyanite minerals consumed annually, but non-refractory uses are expanding.3 Most mullite refractories are used as furnace linings in metallurgical and glass manufacturing furnaces. The remainder is used largely for kilns, kiln furniture, and saggers by the ceramic industry. Small quantities of kyanite without calcination are used as a source of alumina in the manufacture of glass, electrical and chemical, porcelain, pyrometer tubes, and in the form of kyanite concentrate to increase the alumina content of fireclays. Kyanite is used to improve workability, increase strength, and to compensate for firing shrinkage in floor and wall tile and other ceramic products.

Jan 1, 1968

By D. H. Lynch

This paper is a general description of current Central Florida phosphate mining, beneficiation and product transportation. It is directed and believed to be of interest to engineers not familiar with this industry.

Jan 1, 1978

By C. Anderson, B. Schug, C. Cristoffanini, S. Nazari

The Haile Gold Mine in South Carolina is increasing the automation level of their processing plant in order to improve operational stability. One step towards this goal is the application of a Digital Twin concept to provide Virtual Instruments. Haile has engaged ANDRITZ to implement Virtual Instruments at their grinding area hydrocyclones and at their tailing thickener underflow pump. These virtual instruments provide density values in a traditionally difficult location for reliable slurry density measurement. The Digital Twin is a first principles IDEAS1 ™ simulation model, connected in real time to the control system. Results have been promising, with the virtual instrument values matching the physical instrument under normal operating conditions, and showing better prediction under upset conditions. Haile plans to use the virtual instruments as optional process control parameters. INTRODUCTION OceanaGold’s Haile Gold Mine is located near Kershaw, South Carolina, about 50 miles southeast of Charlotte, North Carolina. This location was first mined in 1827, and has produced gold through several operating periods since then, including a heap leaching operation from 1985 through 1992. In October, 2015, OceanaGold acquired Romarco Minerals, the previous owner of the Haile Operation. The current operation began in 2017 as an open pit mine with additional underground resources. The nameplate throughput is 6,350 tpd ore, and 2017 production was 118k oz gold, with 140 to 155k oz gold expected in 2018. Proven and Probable reserves exceed 3 Moz. The process, as shown in Figure 1, includes a primary jaw crusher, comminution with a Semi-Autonomous Grinding (SAG) mill and ball mill circuit, flash flotation, rougher flotation, regrinding, pre-aeration, carbon in leach (CIL) leaching, carbon elution and regeneration, cyanide recovery, electrowinning and refining. The Haile Operation’s inaugural gold pour took place January 20, 2017. Mine life is expected through at least the year 2030. Based partially on prior experience of some key OceanaGold personnel with automation services from ANDRITZ on other projects, OceanaGold decided to include ANDRITZ on the Haile project. The scope of these services for Haile included design and supply of the process control application software, an ANDRITZ dynamic process simulator for operator training, and ANDRITZ Advanced Control Expert (ACE) ®2 systems for the SAG mill, ball mill, and rougher flotation areas. Since startup, ANDRITZ has continued to provide services for the site, particularly related to PLC and HMI equipment, programming and support, ACE system expansion, and the implementation of Virtual Instrumentation. The implementation of this new Virtual Instrumentation technology at Haile is consistent with Haile goals: increased automation, a change in the role of the operator from interactor to monitor, and improved stability by removing human error.

Jan 1, 2019

By W. W. Vaughn

In the technique described and evaluated, detection of mercury is based on the principle of atomic absorption. An analog signal, produced when mercury vapor absorbs ultraviolet light, is converted to digital form and calibrated to mercury concentration. Interferences are eliminated by selectively trapping the mercury on gold. The lower limit of sensitivity, using a 1-gram sample, is 5 parts per billion. A model of the instrument mounted in a station wagon has been tested successfully in the field.

Jan 1, 1964

By E. W. Davis

This paper deals with the role of the Maintenance Department in a milling operation; specifically, the Mines Development, Inc., processing plant at Edgement, South Dakota. The goal of very maintenance department is the smooth and uninterrupted operation of the plant it serves, To achieve this goal, maintenance men adapt various features and procedures into a program designed to fit the characteristics of their particular plant operation. A few of the basic elements of a sound maintenance program are: 1, A periodic preventive maintenance schedule. 2, A systematic inspection and lubrication procedure. 3. A training program for maintenance personnel. 4 A good equipment-history file system, 5. A carefully planned spare parts inventory.

Jan 1, 1962

By P. C. Clark

This paper is an overview of the requirements and concerns for minerals and pigments used in papermaking. The first part of this paper deals with mineral or pigment filling in the actual papermaking process. The second part deals with the pigment or mineral properties that are important in today's coating processes.

Jan 1, 1993

By A. K. Bakshi

An on-line rheometer, suitable for use with slurries, has been developed at Michigan Technological University. This rheometer can be used with both Newtonian and non-Newtonian slurries, and produces complete shear-rate/shear stress curves which characterize the time-independent rheology of the slurry. The sensor utilizes the Hagen-Poiseuille equation and Boyle's Law to calculate the shear rate, slurry flowrate, and shear stress from a series of pressure measurements. The design of the unit allows the measurement sample to be continuously collected from operating process streams in the often-hostile on-line environment. The shear rate/shear stress curves can be used to conveniently calculate the apparent viscosity at any given shear rate, and also to measure any yield stress or other deviations from Newtonian behavior.

Jan 1, 1999

By M. Baumann

Operating and maintaining the heavy equipment used in open-pit mining operations is an ongoing challenge for mines. Typical operations employ a combination of shovels, wheel loaders, and haul trucks to excavate and transport the material for further processing. As this is the first point of contact for the material after blasting, it is often a bottleneck of all downstream processes, thus, equipment uptime and efficiency is crucial. Automated systems for bucket tooth monitoring, payload measurement, proximity detection, and rock fragmentation analysis will be examined. The impact of these systems on operation safety, efficiency, and reliability, in real-world scenarios will be investigated. The process of managing all the above fleet of equipment in a mine can be streamlined by connecting the equipment monitoring systems to a central server. Using the central server, the distribution of this information can be automated to ensure that the right people see the data in a timely manner, improving both proactive and reactive responses to threats to safety and productivity.

Feb 23, 2014

By G. H. Harris

The flotation behavior of two high sulfur coals using a non-ionic surfactant as collector from two series of compounds containing oxygenated functional groups was studied in detail using a 2-liter Denver flotation cell. The performance of these reagents was compared with that of an oily collector, namely dodecane. The results showed that at the same coal recovery, a much lower dosage of these non-ionic surfactants was required as compared with that of dodecane. More import was the performance of these compounds as promoters for oxidized as well as un oxidized coal. Mechanisms of interaction of these compounds with the coal are suggested.

Jan 1, 1993

By L. L. Probert

A three-year project focusing on the depth profiling of respirable coal mine dust particles using scanning electron microscopy coupled with energy dispersive x-ray analysis resulted in the development of statistically classified particle-behavior models. The models depict the changing silicon fraction for 5-, 7-, 9-, and 11-keV accelerating voltages, thereby giving a clear indication of the nature of various types of particles. This paper will focus on the results for respirable quartz particles that occur in underground coal mines across the U.S. The relationship between the amount of surface-available quartz and coal seam rank is well established for Pennsylvania

Jan 1, 1994

By A. L. Hinde

Ideally, mill circuits should be controlled so that excessive random disturbances are reduced in frequency and amplitude. It is difficult to derive an objective measure of the effectiveness of any chosen control strategy. Often, the response of the circuit to pulse or sinusoidal disturbances is used as a measure of the effectiveness of control, but this is not adequate in many circumstances because such disturbances bear little resemblance to those that occur in practice, and such an approach cannot be easily related to the profitability of the reduction process. A superior approach appears to be the application of the theory of stochastic processes. This theory permits both real process disturbances to be modelled accurately, and useful objective functions for control to be derived. A test of the usefulness of stochastic theory in mill control was made on the gold ore milling circuit shown in Figure 1. This circuit was fed with an ore which had a liberation characteristic such as that shown in Figure 2. It is simple to show that, for such a liberation characteristic, the recovery of valuable mineral will vary as the standard deviation of the particle mass-size distribution varies even though the mean particle mass-size is kept constant. Similarly it may be shown that excessive perturbations in the circulating load in a milling circuit such as that shown in Figure 1 can affect liberation. Figure 3 shows how, as the cyclone feed density increases and the sump water addition decreases at constant sump level, the cyclone operation becomes unstable and the discharge "ropes? with a consequent catastrophic coarsening in product size. By minimising the variance of the circulating load it is possible to reduce the probability of initiating instabilities of this nature.

Jan 1, 1977

By K. J. Shelswell

This work describes the design, analysis, and comparison of discrete simulation and static spreadsheet models developed to compare the oreflow efficiency of two conveyor-based material handling systems; one approach with a conveyor stream in series and one with parallel conveyor streams. Analysis and comparison indicated that daily rates were significantly affected by random conveyor failures in both designs. The compound effect of random failures limited the effectiveness of long belt assemblies in series, while the parallel conveyor stream design partially alleviated this constraint. The static spreadsheet model predicted a lower average daily oreflow rate for the series conveyor stream design and a higher average daily oreflow rate for the design with parallel conveyor streams when compared to the discrete simulation results. These discrepancies were the product of model sensitivity to operational factors incorporated in the system and provided the opportunity to further use the discrete simulation models for trade-off comparisons and sensitivity breakdowns of mine operating practices and material handling system efficiencies in both the series and parallel belt stream designs

Feb 23, 2014