Search Documents

By L. F. Ruppert, R. C. Milici

Coalbed methane (CBM) is currently being produced from a relatively small area in the Dunkard and Pocahontas basins, in the northern and central parts of the Appalachian Basin, respectively. In general, much of the production occurs where the coal beds are beneath 500 feet or more of overburden, where the rank of the coal is high-volatile B or greater (%Ro >0.8), and where the natural fracture system is enhanced by structural deformation. It is anticipated that near-term CBM development will continue within these areas and will expand in the Appalachian basin as technology improves and as the price of gas rises.

Jan 1, 2003

By M. E. Rossi

This paper discusses the use of Conditional Simulation (CS) models to provide mill feed grade profiles for different time periods. The conventional approach of classifying block estimates as ore or waste generally does not adequately represent dilution, lost ore and the anticipated grade control data, including variability of mill feed from the pit and possible stockpiles. The detailed simulation of grade control practices can be done, but at the Pre- or Feasibility stage of the project may be impractical, since drawing dig limits on multiple benches is tedious and time consuming. Using the Feasibility Grade Control (FGC) method as developed by the Centre for Computational Geostatistics (CCG, University of Alberta-Edmonton), the CS models can be processed quickly to establish dilution and lost ore, and predict daily or short-term feed to the mill. The simulated nodes can be aggregated into selective mining units with adequate representation of likely geometries to be recovered from the pit, to mimic anticipated selectivity. An example from a large copper deposit is shown. The study provides an estimated stream of tonnages and grades fed to the plant by mining periods of interest and based on a specific mine design and schedule. The resulting cash flows support the economic and financial analyses of the Feasibility Study; also leads to improving mine schedules; and aids in developing blending schemes if necessary. INTRODUCTION The conventional approach of separating mineralized material into ore or waste categories does not always include a realistic amount of dilution and ore loss. Also, often it does not provide a good estimate of the grade that will be fed to the mill. If the grade control estimates are unbiased, they will over the long run represent the long-term average of grades fed to the mill; but the anticipated variability of mill feed from the pit and stockpile sources may be misrepresented. Some references on traditional grade control implementations can be found in Chunnett (1982); Davis et al. (1989); Srivastava et al. (1992); and Nowak (1992). Alternative methods based on economic variables improved significantly on the purely grade-based control methods, see Douglas et al. (1994). Further developments involved the use of geostatistical conditional simulations (CS) and profit models, which in several cases have been successfully implemented (Aguilar and Rossi, 1996; Rossi, 1997; Deutsch et al., 2000; Norrena and Deutsch, 2002; Neufeld, 2005; Jewbali and Dimitrakopoulos, 2009). But they can be impractical, mostly due to the lack of understanding of the methodology involved; even if semi-automatic dig limit drawing is implemented, there is always a need for is tedious and time consuming checking and corrections, even if using a single profit model derived from the simulated grades.

Jan 1, 2019

By R. L. Grayson

Using powerful database management software, nested-field analysis and microanalysis of narratives have been made of West Virginia accident data, resulting in a new approach for targeting and prioritizing safety interventions by county, mine size, specific mine, job title, type injury, etc. and combinations of these parameters. The analyses have been useful in focusing training and discussion sessions on specific work problems, trends, conditions, and situations for targeted groups of miners. Application of the technique will be presented in this paper, along with comparisons of various mine performance measures.

Jan 1, 1997

By A. T. Yu

A recent analysis completed by the United States Department of Commerce predicts that the 1968 Gross National Product will reach a record high of 864 billion dollars. As our nation annually increases its total output of goods and services, as has been the trend, the consumption of steel and its most basic raw material - iron ore - also must increase, To deliver the most economical unit of iron ore to the blast furnace, each segment of the transportation system must be co-ordinated and utilized to its highest degree of efficiency. In some cases, such as with the water segment of the system, a new investment in capacity will be required.

Jan 1, 1968

By James J. Meadows, Jason D. Pampena, Emanuele G. Cauda, Lauren G. Chubb

Exposure to respirable crystalline silica (RCS) can cause serious and irreparable negative health effects, including silicosis and lung cancer. Workers in coal mines have the potential of being exposed to RCS found in dust generated by various mining processes. The silica content of respirable dust in one single mine can vary substantially over both time and location. The current monitoring approach for RCS relies on the use of traditional air sampling followed by laboratory analysis. Results generated using this approach are generally not available for several days to several weeks after sampling, and this delay prevents timely and effective intervention if needed. An alternate analytical method is needed to reduce the time required to quantify the RCS exposure of mine workers. The National Institute for Occupational Safety and Health (NIOSH) has developed a new method using commercially available portable infrared spectrometers for measuring RCS at the end of the sampling shift. This paper will describe the application of the new field-based RCS analytical process for coal mines, including the use of the new method with the existing Coal Mine Dust Personal Sampler Unit. In a case study conducted by NIOSH with a coal mine operator in West Virginia, field-based RCS analysis was completed at a mine site to evaluate the new technique. The RCS analysis results obtained by the field-based method in this case study showed sufficiently strong correlation with results obtained by the MSHA standard laboratory analysis method to allow the mine operator to use the field-based method for evaluating process improvements.

By Justin Srednicki, Chenming Zhou

Ambient electromagnetic (EM) noise (natural or manmade) is a major limiting factor for the design and operation of many electronic devices, including through-the-earth (TTE) communications and tracking systems. Extensive studies on EM noise were conducted by the US Bureau of Mines in the 1970s and 1980s. Changes in the design and operation of electrical equipment since then, however, have resulted in changes in the EM noise environment. This paper reviews past research on surveying EM noise in the extremely low-frequency (ELF) and very-low-frequency (VLF) bands, which are the operating bands for TTE systems, and introduces a new battery-powered, rugged, portable measurement system for surveying EM noise in mining environments. Examples of surveyed EM noise measurement results in and above an active underground coal mine, using the new system, are presented in terms of absolute magnetic field strength levels. A new metric, average noise level (ANL), is introduced to characterize the noise level relative to a particular frequency band for a specific location. It is found that EM noise in mining environments varies significantly with time and location. EM noise levels at frequencies of 30 Hz that shifted from power harmonics (e.g., 90, 150, 210, 270 Hz) are relatively low and their variation with time can be statistically modeled by a Gaussian distribution. The conclusions and findings presented in this paper can help better design and operate TTE communications and tracking systems in underground mines.

Oct 14, 2022

By Ben V. Petersen

Surveying is to tunneling, as a steering wheel is to a car—somewhat essential if you want to end up in the right place. The principles of tunnel surveying have remained unchanged since the first tunnels were constructed: To mathematically connect the selected start and end points of a tunnel and physically translate that alignment onto the ground. The alternative is just dead-reckoning and leaves the probably less than satisfying end results to chance. Today’s laser-guided tunnels often have to thread the needle through a maze of soil types, utilities, structural features and other underground considerations. Surveying makes it possible.

Jan 1, 2005

By S. S. Sephton

Sintering as applied to agglomeration of ferrous fines has shown little growth in the United States in recent years. The general concensus was that most of the existing facilities would remain in production at a reduced tonnage to dispose of and recover solid waste from steel plants. Further growth for ferrous sintering technology was not in sight in the United States and in the early sixties expansion came to a virtual standstill, however, we witnessed a rapid emergence of a tremendous pelletizing industry. On other continents, due to different raw materials supply and capital structure, sintering technology continued to grow, with a more cautious development of pelletizing installations. In the U.S. the diminishing supply of good quality, high grade coarse ore resulted in eventual disappearance of high grade ore fines for sintering. The finely divided concentrates produced from lower grade ores were not amenable to this type of agglomeration, but were more suitable for pelletizing. Furthermore, pellets seemed to possess all the features of an ideal blast furnace feed; namely pellets are free flowing, uniform in size, strong, with extremely uniform chemical composition and good reducibility. Importance and demand for such well stabilized furnace feed further increased as size of newly installed blast furnaces continued to grow. The in- creasing demand for a uniform, stabilized burden coincided with the effort to produce a fully beneficiated burden for smelting, thus reverting the blast furnace to its primary function of smelting.

Jan 1, 1973

By Theodore H. Eyde

In the southwest porphyry copper province, the virgin prospect with good copper mineralization cropping out has disappeared. Future discoveries will require an increasingly sophisticated arsenal of exploration techniques and concepts. One of the latter, stratigraphic analysis, is a technique which is often overlooked. A surprising number of exploration geologists still think of porphyry copper deposits as occurring wholly within intrusive bodies such as quartz monzonite or granodiorite. Disseminated copper mineralization, though genetically related to intrusive rocks, can occur within both the intrusive and the intruded rocks. At present, as much as 30% of the total copper produced from disseminated copper deposits in the Southwest originate from the intruded rocks rather than the intrusive. George M. Schwartz, in "Geology of the Porphyry Copper Deposits of Southwestern North America" points out that the host rocks at porphyry copper deposits include such diverse rock types as diabase, granite, limestone, dolomite, quartzite, skern, sericite schista, and others in addition to the more common monzonite, quartz-monzonite, and diorite porphyrys. Therefore, a porphyry copper can be defined as a disseminated copper deposit occurring either in or adjacent to a granitic-monzonitic-dioritic intrusive which can be exploited using bulk. mining techniques. The original definition of porphyry was originally applied to the early producers, such as Inspiration, Bingham, and Ajo, in which the copper mineralization occurred principally within the intrusive. A review of the geologic literature describing the porphyry geologic

Jan 1, 1971

By G. W. McMahon

Following the Sago Mine accident, the U.S. Mine Safety and Health Administration (MSHA) asked the U.S. Army Engineer Research and Development Center to study several possible methane explosion scenarios in the Sago coal mine. The study used a 0.3-m (1-ft) resolution map of the mine to produce a 3-dimensional (3 D) model of a portion of the mine, including the sealed area where the explosion occurred. An advanced 3 D computational fluid dynamics (CFD) code was used to calculate the explosion pressures within the sealed area, on the mine seals and in nearby regions of the mine. Based on the best available information on methane concentrations and assumptions on homogeneity and on layering and mix composition, three separate initial conditions of methane-air concentrations and location were studied. This paper discusses the CFD modeling technique, the results of the calculations, the challenges of conducting this type of modeling and the advantages and limitations of CFD modeling of accident investigations of mine explosions.

Jul 1, 2010

By M. K. Mohanty

Due to inefficiencies of the flotation process, significant effort has been recently provided to develop gravity separators for treating ultrafine particles. As a result, several enhanced gravity concentrators have been developed and commercialized. The Altair Centrifugal Jig is an enhanced gravity separator that provides relatively efficient separations on +25 µm size fractions. An experimental program conducted on -600 µm coal found that the Altair Jig reduced the ash content of the 600 x 44 µm from about 30% to 10% with an 86% combustible recovery value. The pulse water pressure, feed volumetric rate and ragging volume were found to be the key operating parameters affecting the separation performances obtained from the process. An extremely low density cut point of 1.54 and an Ep value of 0.08 were indicative of the high process efficiency values achievable by the Altair jig.

Jan 1, 1998

By Roger D. Sharpe

Oklahoma contains extensive resources of high-purity gypsum that were deposited in the Anadarko and Hollis basins during Permian time. The gypsum resources and reserves are estimated to be about 48 billion short tons and a; located in the western portion of the state. Oklahoma is the largest producer of gypsum products in the United States. The Blaine Formation and the Cloud Chief Gypsum contain several beds of minable thickness. Four stratigraphic units in the Blaine Formation are quarried in Oklahoma. The Shimer, Nescatunga, and Medicine Lodge Members are quarried in northwest Oklahoma. The Van Vacter Member, consisting of three gypsum beds, is quarried in southwest Oklahoma. The Cloud Chief Gypsum is quarried in the west-central part of the state. The gently dipping gypsum in the Blaine Formation generally crops out along low escarpments and is covered in the downdip direction by increasing overburden, consisting of sand, shale, and/or dolomite. Anhydrite occurs in the downdip direction under the thicker overburden. The Cloud Chief Gypsum crops out as hills, which are eroded remnants of a more widespread, massive sulfate unit. All of the gypsum produced in Oklahoma is extracted using quarrying methods. A variety of products are made from gypsum quarried in Oklahoma. The products are manufactured from uncalcined, calcined, and deadburned gypsum. Products vary from raw, ground gypsum used for agriculture, to high-value-added industrial plasters, cements, and fillers produced from calcined gypsum. A sampling of the many products manufactured from Oklahoma gypsumincludes: (1) agricultural-soil amendment; carrier for insecticides, pesticides, and herbicides; calcium supplement in animal feeds; (2) gypsum wallboard-common, fire-resistant, and water-resistant varieties; (3) industrialgypsum plasters-art and casting, pottery and ceramic, molding and tooling, crayons, wall patching; (4) industrial gypsum cements-oil-well cement, high-strength statuary, high-strength tooling, fiber-reinforced architectural, road and bridge repair; (5) food and pharmaceutical-filler and binder in aspirin and other medicines, yeast activator in brewing of beer, moisture absorbent in bread and pizza dough; and (6)portland-cement retarder-ground with clinker to control setting time.

Jan 1, 1999

By Vishwajeet Ahuja, Benoit Jones

"INTRODUCTION Shotcrete lining forms an integral part of conventional tunneling and is widely applied for underground excavations. Early strength gain of the shotcrete is a crucial aspect for ground support and safety of operatives. Strength requirements are dependent on various factors such as lining thickness, ground type, excavation size and tunnel depth. The early strength gain is typically monitored using destructive tests, such as needle penetration, stud driving or coring samples for uniaxial compressive strength testing in the laboratory. Being destructive, these tests cannot be directly performed onto the lining without causing damage that must be repaired, which is a particular problem for permanent linings. For this reason and to avoid the need for operatives to work near to exposed ground and/or fresh shotcrete, these destructive tests are often performed on panels, which are sprayed at the same time as the tunnel lining. All current testing methods are also very local, testing only a small part of the lining or a panel, which may not be representative because the temperature history could be significantly different. Therefore, these tests do not provide an accurate or complete picture of the lining strength gain. New testing methods that are non-destructive and can scan the whole lining remotely would be extremely desirable. This paper describes a new method, using thermal imaging techniques, that achieves these aims. It also discusses the real-time on-site application of the method, providing insight into the experience gained and conclusions derived. Shotcrete Shotcrete used for tunnel linings requires immediate strength development. The strength development is a direct result of the hydration reaction of cementitious materials present in it. A progressive sequence of the hydration reaction changes it from a solid suspension (typically referred to as fresh concrete) to a solid skeleton with a porous network and thereafter, into a solid with predominantly discontinuous pores (Byfors 1980). In the case of shotcrete, early strength is needed to support the self-weight and then continuing early age strength gain is required to begin to support ground loads. These strength requirements, along with other workability needs, are met by careful concrete mix design, the use of admixtures, such as accelerator and superplasticizer (BS EN 934-5 2007), and supplementary cementitious materials, such as silica fume."

Jan 1, 2016

By William J. Cavanaugh

In 1967, Lone Star Industries, Incorporated, established a program to carry out the necessary Research and Development work to bring the Snyder Process to commercial application. The purpose of this paper, is to present the detailed metallurgical results gathered in comparing the Snyder Process of Comminution to conventional grinding techniques for the milling and beneficiation of certain ores and other materials. The ore primarily dealt with in this paper is a fine-grained magnetite ore, containing approximately 23% acid-soluble iron, from the Lake St. Joseph ore body of Steep Rock Iron Mines, Ltd., (Canada). This particular example was selected for presentation in this paper because extensive comparative results with conventional methods of grinding were available. Also briefly described in the paper are the comminution of other ores and materials such as porphyry copper ore and alumina.

Jan 1, 1973

By R. Benito

This paper describes the development of a life-of-mine schedule (LOM) for one of the world's largest known sedimentary copper-cobalt districts located in the Katanga Province, Democratic Republic of Congo (DRC). A particular feature of the Tenke Fungurume LOM schedule is the considerable number of pits/phases for scheduling, each competing to provide the best ore available to a capacity-constrained process facility. This paper discusses the LOM scheduling objectives and constraints, data preprocessing steps such as ore binning, block aggregation and clustering analysis as a scheduling aid, the mine scheduling approach and results and conclusions. Mining Engineering, 2011, Vol. 63, No. 8, pp. 39-47. Official publication of the Society for Mining, Metallurgy and Exploration, Inc.

Jan 1, 2011

By M. J. Virnig, B. D. Boley, G. A. Wolfe, J. M. W. Mackenzie

A flowsheet for the recovery of nickel and cobalt from laterite ores has been developed which involves acid leaching followed by hydroxide precipitation of the metal values and then releaching of the hydroxide cake with ammonia. Investigations of the chemistry of extraction of nickel by LIX® 84-I and a developmental reagent, XI-84-IT, along with the physical properties of the organic phases are described. Based on these investigations, suggestions with regard to design of a solvent extraction plant and operating conditions are made.

Jan 1, 1999

By S. Lu, J. P. Barta, T. W. Meikle

Three nutrient amendments and a biological seed inoculant were evaluated for use in establishing vegetative cover on waste rock substrates. Randomized blocks were placed on three substrates. Treatments included two types of organic fertilizer, mineral fertilizer, Azospirillum bacterial inoculant, plus controls. The seed mix consisted of native grass species adapted to low nutrient conditions. Canopy cover has been monitored for three growing seasons. Results indicate : 1) two of three substrates support plant growth following amendment with organic fertilizers; 2) organic fertilizers increase cover substantially over mineral fertilizer; and 3)Azospirillum had no effect on canopy cover.

Jan 1, 1999

By Fred Delabbio, Sverker Hartwig

As openpit copper operations transition from surface mines to underground, the speed of underground infrastructure construction prior to production is critical for maximizing the value of the project. Typically, the preferred underground bulk mining method is block caving. In preparation for future underground projects, Rio Tinto made the strategic decision to invest in a step-change program that would develop system solutions to reduce the construction time of block caves. The program focused on improving safety and doubling or more the construction speed of both vertical shafts and horizontal infrastructure compared to existing drill-and-blast rates. After an extensive selection process, Rio Tinto selected the Atlas Copco mobile miner machine as one of the concepts to proceed with for construction of horizontal infrastructure for access and footprint. In addition to un-derground drilling and hauling equipment, Atlas Copco?s Robbins mobile miner concept (a previous attempt at horizontal mechanical excavation) completed trials at Mount Isa, Pasminco and Taisei. Rio Tinto selected the new Atlas Copco mobile miner machine concept for a number of reasons including the use of proven technology from the three previous mobile miner machines and other commercial products, as well as the ability to install complete ground support typical with high rock stress conditions at approximately 1,500 to 2,000 m (4,900 to 6,500 ft) depth. Atlas Copco, with support from Rowa, the Swiss company that specializes in back up systems for tunnel boring machines (TBM), is advancing the detail design of the access version of a tunneling system on behalf of Rio Tinto. Because of the different requirements between an excavation system for access tunnels and that for tunnels on the footprint, two different versions of the mobile miner machine technology were envisioned. The access and the footprint versions of the Atlas Copco mobile miner machine share a majority of key technologies and systems. Therefore, it was possible to conduct a performance conformation test using a full-scale version of the access machine that would also mitigate the technical risks for the footprint version. To alleviate confusion, this article focuses on the access version of the Atlas

Jul 1, 2010

By J. Drelich

The wetting behavior of liquid polymers at solid surfaces and the adhesion forces involved at polymer-filler interfaces should always be considered in the fabrication of high quality polymer composites, including those made with mineral fillers. Spontaneous polymer spreading over the filler surface is a basic condition in the fabrication of the polymer-mineral composites. In this regard, the wetting and adhesion characteristics of polymer-mineral systems are reviewed in this contribution. It appears that several aspects of wetting phenomena at mineral filler surfaces are not well described in the literature and require further systematic study. Specifically, it is clear from this review that efforts should be made to determine the effects of mineral surface contamination (including surface hydration) on wetting and adhesion phenomena, and to determine the wetting characteristics of molten polymers at mineral filler surfaces. It is expected that any improved fundamental understanding of wetting and adhesion phenomena for the polymer-mineral composites will provide the basis for further technological development.

Jan 1, 1995

By K. Fountain

In Novemeber of last year I visited a mica mine in Hunan Province, China. For nine months , we had been trying to sell Chinese mica to a customer in Belgium. Talking to the customer was like negotitating with a stone wall. The buyer refused to communicate any -thing other than his steadfast refusal to consider Chinese mica. He would not advise us what he wanted, what specifications or grades. He would give no indication if our price at market, or reasonable, or totally out to lunch. He would not even accept samples. It took no genius to guess that the mica buyer had at some time in the past bought a shipment of Chinese mica and had received a disaster. I invited the mica mine in Hunan in order to see for myself what could be done - without massive investment in equipment and instruments - to upgrade the quality of the mica for export. We had seen this type of customer reaction before. One disgruntled customer who had pur¬chased pigment grade barites direct from China ranted and raved about unreliable and inconsistent quality. It did no good to explain to him that China is a big country, with hundreds of mines scattered throughout many areas, each producing a different product. Our further explanation that Chinese export organizations also varied in degree and efficiency of customer service fell on deaf ears. Samples had no effect on his perception. Eventually we showed him photoraphs of two mountains of pigment grade barites. One lot was our sales of pigment barites to a major European minerals processor. Our Chinese barites stood proudly white and beautiful next to a hill of other material which now appeared at best mediocre and dull by comparison, and which the buyer had decided to reject after he received our Chinese barites. Finally the customer was sufficiently impressed to look seriously at our guaranteed specification and the outturn analysis performed by our other customer.

Jan 1, 1987