Search Documents

By S. A. Abdel Sabour

Conventional methods for selecting a production plan for an open pit mine is based on the assumption that ore grades throughout mine life as well as market variables are known with certainty. Another important issue that is also being ignored in the conventional procedure is the value of management flexibility to revise operating policy with time according to the arrival of new information. Based on this oversimplification of reality, an optimum mine plan that is thought to be maximizing net present value (NPV) of the project is selected. Given the multiple sources of risk affecting the estimated NPV, there is a high probability that the actual value will be different from that estimated. This could mislead decision making process regarding selecting an optimum mine plan. This paper proposes a multi-criteria ranking system for selection between alternative mine designs under both geological and market uncertainties. The system is based on integrating multiple market and geological uncertainties as well as the operating flexibility to revise the ultimate pit limits using a Monte Carlo-based real options valuation (ROV) model. To compare the methods, the article applies the proposed system, along with the conventional NPV-based method, to rank possible mine designs for a copper and a gold mine. It has been found that, considering multiple risk analysis measures while integrating uncertainty and operating flexibility results in selecting a mine design that is different from that selected by the conventional method.

Jan 1, 2009

By M. Oliverio

The Cigar Lake uranium deposit was discovered in 1981 at the south western end of Waterbury Lake, approximately 660 km north of Saskatoon in the province of Saskatchewan (see Figure 1). It is the largest undeveloped high grade uranium deposit in the world. It contains proven and probable reserves of more than 226 million pounds U3O8 at an average grade of 20.7%. The world average grade is less than 1% U3O8. [ ] The ore body is located about 450 m below surface at the interface between sandstone above and basement rock below (see Figure 2). The sandstone is fractured rock and saturated with water. This makes water inflow a real hazard at the mine. In fact there have already been two significant mine inflow events. The first of these occurred in October 2006 and resulted in the flooding of the mine. The second occurred in August, 2008 during mine recovery activities.

Jan 1, 2011

By G. J. Joy

Although rates of pneumoconiosis in coal miners have declined substantially in the United States since the passage of the Federal Coal Mine Health and Safety Act of 1969, new cases continue to occur, including cases of rapidly progressive disease. In contrast, Australia?s underground coal mining industry has reported few new cases of pneumoconiosis for over twenty years. Mortality from Coal Workers? Pneumoconiosis in official health statistics and the prevalence of pneumoconiosis among miners screened in x-ray surveillance programs are also lower in Australia. To understand this disparity, the National Institute for Occupational Safety and Health was requested by both industry and labor stakeholders to examine this issue, with the ultimate aim of reducing the rate of pneumoconiosis among United States coal miners. A number of factors, including coal dust exposure, silica exposure, and coal rank were examined as potential contributors to the above observed differences. Comparison of coal rank data from each country did not show any significant differences. Air sample data from the coal mining industries in both countries show that coal dust levels in Australian mines are somewhat higher than those reported in similar U.S. mines; however, quartz exposure for Australian miners is lower than for many U.S. miners. Assuming that quartz is contributing to the greater number of cases of advanced pneumoconiosis in the U.S., more effective dust control measures, as well an independent exposure standard for respirable quartz in coal mining, need to be implemented to prevent this potentially disabling condition.

Jan 1, 2011

By W. Randall, Robert M. Leary

Twin 1250 m (4100 ft.) long highway tunnels through Cumberland Mountain near Middlesboro, Kentucky are planned to be completed in the early 1990's. The tunnels will be excavated in sandstones, limestones, and shales, dipping at 35 to 50 degrees and striking nearly perpendicular to the tunnel alignment. In 1985-86 a pilot tunnel was excavated as a crown drift along the alignment of the southbound tunnel. The benefits of the pilot tunnel in reducing uncertainties for main tunnel construction are discussed. The cost-benefits of the pilot tunnel are examined in view of estimated main tunnel costs.

Jan 1, 1987

By Aldino Campos, Frederico Carvalho Dias, Pedro Madureira, Patrícia Conceição, José Gomes-Pereira, Inês Tojeira, Andreia Afonso, António Calado, Luísa Pinto Ribeiro

Since 2008, the Portuguese Task Group for the Extension of the Continental Shelf has been operating the ROV "Luso" (rated for 6000m depth) for geological sampling of the deep North Atlantic seabed, performing surveys on, e.g., seamounts and hydrothermal vent fields. Amongst other sensors, the ROV is equipped with a full HD video camera with which still images of the deep ocean floor are recorded. Fixed on the ROV’s frame are two underwater "line" lasers, each generating a sharp green line (532nm) over the seabed. The two lasers are paralleled and calibrated at a set distance. Provided that the camera’s angle of view is known, numerical values for seabed surface area may be calculated using direct measurements taken from the pictures containing the laser lines. We present the corresponding main mathematical formulas, which are derived from simple geometrical considerations, and discuss how to generalize these results for an arbitrary camera tilt or pan. We present an example of application of our method by estimating values for percent coverage of rock substrate versus sediment. Our results are also relevant for determining seabed polymetallic nodule abundances from still images obtained during ROV surveys.

Sep 1, 2014

By D. Bogh

Wound rotor motors are used in difficult mining applications where there is a need to start high inertia, hard starting loads while limiting inrush current They are recognized as robust and simple to control. This paper will cover the performance, specification, and important issues to be considered when applying medium voltage wound rotor motors in mining applications. Medium voltage grinding, crusher, and conveyor applications will be discussed. Specifically covered are motor efficiency, speed range, and rotor control. Crane motors often have wound rotor construction, but their load cycle and ratings are outside the scope of this paper.

Jan 1, 2011

By G. Luttrell, S. Keles, M. Eraydin, R. Yoon

The dewatering of fine particles is energy intensive and often requires costly capital expenditures. To address these issues, a series of advanced dewatering technologies have been developed at Virginia Tech. These include novel dewatering aids that enhance the performance of existing filtration equipment and an innovative hyperbaric centrifuge that utilizes both air pressure and centrifugal force for dewatering. The moistures obtained using these processes are 30-50% lower than those obtained using conventional methods. Another dewatering technology, known as the hydrophobic displacement process, can reduce product moistures to a level previously attainable only through the use of thermal dryers. This article presents test results obtained with these various advanced dewatering technologies along with estimates of the power consumption for each process.

Jan 1, 2007

By R. Washnock, P. James

"INTRODUCTION Abstract Tankhouse iron control through application of new treatment technology to mitigate conventional bleeding losses is considered. Implementation is discussed and the treatment economics explored. A representative case is assessed. Treatment benefits and application drivers for specific scenarios are noted. Background Hydrometallurgical ore processing has become a significant metal extraction/production avenue in recent decades. In copper mining; the focus for this examination, around 25% of global primary copper production and nearly 50% of US production result from various hydrothermal leaching extraction approaches coupled to Solvent Extraction/Electrowinning (SX/EW) metal production. Generally such processing is favored over pyrometallurgical processes for lower ore grades and as such is finding growing use and is expected to remain a key processing route looking forward with average world-wide ore grades falling as known ore reserves become exhausted. Target Problem And Motivation In hydrometallurgical processing the production circuit may be thought of as a chain of interlocked recirculation loops (Figure 1). Leaching dissolves the target metal from the ore along with other ore components which contaminate the Pregnant Leach Solution (PLS). Iron is a common component in copper ores and, as a result, occurs fairly ubiquitously in copper Pregnant Leach Solutions (PLS) generated by leaching. Leached components migrate through the production circuit from left to right (Figure 1) through a net combination of chemical and mechanical transport mechanisms. Selectivity at the recirculation loop interfaces tends to retard rejected component migration through the production process. As a result, overall relative contaminant migration fluxes are slower than the target metal (copper) and the contaminants tend to build up relative to copper in the more upstream portions of the processing circuit over time with iron often being a significant contaminant. Further, while copper is continuously removed from the system in appreciable amounts, little contaminant exit occurs and the absolute contaminant amounts and concentrations also increase throughout the EW circuit over time."

Jan 1, 2018

By Joy Sandberg

The 1989 mining industry compensation survey done annually by the Denver-based Mountain States Employers Council shows the "average" or "typical" employee in the mining industry is projected to receive an increase of 3.9% to base pay in 1990, compared to a projection of 4.1 % for 1989. According to MSEC, the actual percentage increase to base pay has continued to decline since 1980. A review of pay increases since 1980 shows the highest average increase was 11%, granted in 1981. Since 1981, there has been a steady deceleration through the decade. While 1989 final figures are not available, 1988 numbers might indicate a reversal of this trend. In 1988, the average employee actual increase was 3.8%. That was 0.7% higher than the 3.1% projection. This may be significant as actual increases have been lower than projections since 1982. Chart A shows the pattern of projected vs. actual percent increases in pay since 1980.

Jan 1, 1990

By Kritika Baxla, M. Mustafa Kahraman, Frank A. Drews, Yaxue Wang, Joel M. Haight, Kody Powell, Mohit Sobalkar, W. Pratt Rogers

In the opinion of these authors, technology alone can never give an organization an edge over competitors or provide an industry step change. However, history has shown that technology applied with correct logistics and strategy makes a significant difference. Never has the minerals industry faced such daunting challenges and been in such need of a step change. Application of autonomous systems has been steadily increasing in the minerals industry. Automation technology has changed the mining value chain from exploration to mineral processing and refining. The future state will only see additional in-roads of automation into more processes and the whole system design. To better understand the near-future potential of automation, it is useful to explore and review the current state of automation in minerals development. A review of the state of automation research is given. The review will consider three critical areas: automation technology, system’s engineering and management processes around automation, and the role of human factors engineering in automated and semi-automated systems. The review ends with a discussion on the social and political risks of automation in terms of shared value and sustainable development.

The inquiry into the explosion at the Moura No. 2 Mine in August 1994 recommended -?Emergency procedures should be exercised at each mine on a systematic basis, the minimum requirement being on an annual basis for each mine.? (Windridge et al. 1996). In December 1996 the ?Approved Standard for the Conduct of Emergency Procedures Exercises? was published and has been subsequently revised (Queensland Department of Mines and Energy Safety and Health Division 1999). This document provided guidelines for conducting mine site emergency exercises as well as the requirement for a test of state-wide emergency response by holding a Level 1 Mine Emergency Exercise at one mine on an annual basis. From 1998 to date (January 2008) ten Level 1 Mine Emergency Exercises have been held in Queensland, Australia. This paper discusses each of the exercises conducted to date as well as the logistics, scenario preparation, planning and organising required to conduct emergency exercises at this level.

Jan 1, 2009

By T. R. Ellis

The author attempted to concurrently apply the US Uniform Standards of Professional Appraisal Practice and the Australian VALMIN Code to a complex mineral property appraisal assignment. This led the author into many severe difficulties. These difficulties included the high standards needed in the work of others, and information and statements needed from the client. The exercise also highlighted many positive features of both documents. Some conflicts were found between the two documents. Implications and thoughts regarding the development of a set of US minerals appraisal standards are discussed.

Jan 1, 2000

By W. X. Wang

In the mining and quarry industries, rock fragments are often transported by conveyor belt. To estimate the qualities of the rock fragments (i.e., size distribution and shape), an operator must take samples from the conveyor and manually perform a sieve analysis, which is time-consuming and tedious. Alternatively, an image-analysis system can be used to monitor the fragment quality on a fast moving conveyor belt. However, images of fragments on a fast moving belt vary to such a degree that the quality of any two successive images are not the same, and some of the images are of such poor quality that they are unrecognizable by human eyes. If poor-quality images are directly analyzed by a segmentation algorithm, the analysis will not be satisfactory. To resolve this problem, it is necessary to use an image-classification pro-gram for the automatic selection of fragment images with good quality. Because of this need, an image-classification program was developed and tested both in the laboratory and in the field. Testing of the system on different types of fragments showed that the system works reasonably well.

Jan 1, 1996

By R. Du Plessis, J. D. Miller, D. G. Kotlyar

The low potential hydrophobic state of pyrite in amyl xanthate flotation with nitrogen is of particular interest with regard to the N2TEC flotation technology currently being used for the recovery of auriferous pyrite at Newmont’s Lone Tree Plant in Nevada. The N2TEC system had been found to operate satisfactorily, but cyanide in the flotation mill water appeared to be responsible for a loss in pyrite recovery. This supposition was confirmed with laboratory experiments and a program was initiated to study flotation chemistry variables by electrochemically controlled contact angle measurements. Experimental results show that activation of pyrite in such cyanide solutions can be achieved more effectively with lead than with copper. Subsequently, based on these fundamental studies, significant improvement at the Lone Tree Plant was achieved by lead activation, in which case the recovery increased to expected levels. The effect of activator is particularly significant not only with respect to pyrite depression by residual cyanide, but also with respect to collector (PAX) consumption and the initial state of the pyrite surface. Each of these issues is being studied in detail and research progress is discussed herein.

Jan 1, 2002

By S. Agarwal

The mining industry collects a significant amount of operational data. However, gleaning useful information from the terabytes of data is difficult, and not just because of the sheer volume of the data. Therefore, an automated tool was developed at the University of Alaska Fairbanks to go through data and apply very sophisticated statistical and neural network techniques, to identify the data streams that are important to a process. This paper presents results from the tool as applied to SAG mill data from a gold mine. The results were benched against commercial tool. Results indicate that there was little or no loss in performance by automating the very complicated process of neural network modeling. Therefore, the intent of the exercise, to examine if complicated modeling tasks can be automated, was realized.

Jan 1, 2011

By G. W. Douglas

The need for dimensionally stable filled polymer composites has spurred the quest for materials that possess a negative coefficient of thermal expansion (CTE). Finding minerals and materials with a negative CTE large enough to counteract the substantial CTE found in polymers proves challenging. Much research has been per-formed over the last decade to uncover various materials that possess this unusual behavior. A list of materials that have demonstrated negative properties are discussed, as well as the experimental use of one such material (ZrW2O8), in a polymer matrix composite. Other negative properties, such as negative Poisson?s ratio and negative stiffness, are also examined. Key words: Negative properties, Coefficient of thermal expansion, Zirconium tungstate

Jan 1, 2010

By F. L. Pirkle, D. L. Pirkle, E. C. Pirkle, W. A. Pirkle

Heavy minerals have been mined from the sands of the United States’ Atlantic Coastal Plain since the early part of the twentieth century. Production of ilmenite from beach sands near Mineral City (Ponte Vedra), Florida, began in 1916. The first reported large-scale recovery of zircon in Florida was reported from this deposit in 1922 and of rutile in 1925. These operations ceased in 1929. Today the Ponte Vedra Country Club and Golf Course is situated in the center of the former mining site. In 1942 heavy-mineral operations were established on 202 hectares of land situated in Duval County, Florida. The location is about 16 kilometers east of the center of Jacksonville, Florida, in an area known as Arlington. This operation demonstrated that low-grade sand containing only 2 to 3 percent titanium minerals could be concentrated economically with the Humphreys spiral and that the oxides could be separated from the heavy silicates by electrostatic methods. Much of this area is now covered by a large mall and is a major retail- commercial center. Between 1958 and 1964 the Skinner tract, a deposit about 4 kilometers south of the above deposit, was mined. Today the area of this deposit is known as Deerwood, a gated country club community on the southside of Jacksonville. Further inland, E.I. du Pont de Nemours and Co. has been mining heavy minerals from a physiographic feature known as Trail Ridge since 1948, and a deposit near Green Cove Springs, Florida has been in production since 1972. Since the start of heavy-mineral mining in the southeastern United States, nine heavy-mineral ore bodies either have been or are being exploited in Florida and Georgia. Other deposits either have been lost to mining or are yet to be mined. These deposits have different origins. Some formed along shorelines at the heights of marine transgressions while others formed on regressional beach ridge plains during periods of temporary stillstands or slight transgressions. These different origins are reflected in the chemical and physical characteristics of the deposits. Ilmenite in older, more western deposits has a higher TiO2 content than ilmenite in younger, more eastern deposits. TiO2 content does not very with north-south direction. Garnet and epidote are absent or rare in the older Trail Ridge deposits, but progressively become common in the younger Duval Upland, Crestal Pamlico, and Holocene deposits. Grain size is coarsest for Trail Ridge sediments and finest for sediments in Duval Upland and Crestal Pamlico deposits. The average grain size for Holocene deposits is intermediate between Trail Ridge and Duval Upland deposits. The two models for the origin of the heavy-mineral deposits – deposits formed at the height of major marine transgression; and deposits formed during periods of temporary stillstands or slight transgressions that occur during a general marine regression; - are consistent with known sedimentological data and depositional trends.

Jan 1, 2005

By S. S. Wang

Dialkyldithiophosphinates are a new class of flotation collectors for base metal sulfide ores. Structurally, they are quite different from the conventional collectors such as mercaptans, xanthates, thionocarbamates and dithiophosphates. Collectors Structures [Mercaptans R-SHS Xanthates R-OCS-M+ Thionocarbamates R-OCNH-R Dithiophosphates 2 R-CCNH-R' Dithiophosphinates (R) 2-PS-M+ ] In the above structural formula, R and R' stand for a hydrocarbon radical, and M+ is an alkali metal or ammonium cation.

Jan 1, 1982

By J. Hunter, E. Jackson

This paper describes work done by Placer Dome Technical Services Limited, a subsidiary of Barrick Gold, and Nautilus Minerals Inc. in support of the conceptual design of a subsea mining system. It describes an overall concept design plus specific studies into mechanical excavation at depth. The concept design includes one or more subsea excavators connected to a suction riser, which transports the cut material to a shipboard dewatering and offloading system. A multi-phase investigation was performed into the mechanical excavation of seafloor massive sulphides at depths of around 1600m. Rock samples were recovered and tested for rock properties and cutting behaviour. A small pick drum cutter was procured and tested on a representative concrete slab in a lab and tested again while submerged in a test tank. Finally the cutter was tested on a massive sulphide ore body at 1600m depth. The cutting performance results, e.g. pick forces and specific energies, should provide valuable input to the design of future full scale subsea mining systems.

Jan 1, 2007

The mining industry, like most other industries, has had a difficult couple of years. What are your thoughts on the industry?s direction in the next few years? I am bullish on our industry. There is no question in my mind that the quality of life we enjoy today is largely a result of our past successes in the minerals and mining sector. I am equally certain that the sustainability of that quality of life and the aspirations of the rest of the world to attain that same level of lifestyle will depend hugely on our future successes and will be the driver for our industry to continue to excel and prosper. Surely, there are going to be challenges along the way. These challenges are not only from the public, regulators and various governing bodies, but also from our industry?s own self regulating efforts. However, we have demonstrated throughout the past several decades that we have the capability to meet these challenges head on and come out ahead.

Jan 3, 2010