Search Documents

By Wolfgang Roth

In 1990, a residential area above the North Outfall Sewer (NOS) tunnel constructed in 1924, experienced subsidence. After sewage was diverted into the North Outfall Replacement Sewer (NORS), soil probing from within the tunnel was conducted, soil-improvement options were developed, and a preferred grouting scheme was analyzed by numerical modeling to evaluate the stability of the 80-year+ old tunnel liner under grouting-induced loading conditions. This paper discusses the initial field investigation and the development and analysis of a grouting scheme originally intended to be implemented before relining of the tunnel. The scheme was later modified, and the new liner was installed before the final probing and grouting work was done.

Jan 1, 2008

By G. S. S. Raman, M. S. Klima

Coal refuse slurries stored in tailings impoundments can potentially lead to environmental concerns such as effluent seepage, property devaluation, and in extreme cases, dam failures. Pressure filtration offers an opportunity to reduce the impoundment requirements by providing significantly drier solids. A full-factorial design was used to study the effects of temperature and pH on dewatering a refuse slurry obtained from a coal preparation facility in Pennsylvania, USA. The experimental results indicated a strong effect of temperature on cake moisture as the cake moisture after about 2800 s was 22% at 43 °C and only 36% at 10 °C for tests conducted at pH 3. ANOVA results confirmed the statistical significance of pH, temperature, and their interaction effect. Also, the results showed no significant differences between the tests conducted near neutral and alkaline pH values at low and ambient temperatures. On the other hand, Tukey's test indicated higher reductions in cake moisture at higher temperatures for lower pH values. This study affirms the need to monitor and control the pressure filtration process as throughput could significantly vary with changes in temperature and slurry conditions.

Jun 17, 2019

By G. S. S. Raman, M. S. Klima

Coal refuse slurries stored in tailings impoundments can potentially lead to environmental concerns such as effluent seepage, property devaluation, and in extreme cases, dam failures. Pressure filtration offers an opportunity to reduce the impoundment requirements by providing significantly drier solids. A full-factorial design was used to study the effects of temperature and pH on dewatering a refuse slurry obtained from a coal preparation facility in Pennsylvania, USA. The experimental results indicated a strong effect of temperature on cake moisture as the cake moisture after about 2800 s was 22% at 43 °C and only 36% at 10 °C for tests conducted at pH 3. ANOVA results confirmed the statistical significance of pH, temperature, and their interaction effect. Also, the results showed no significant differences between the tests conducted near neutral and alkaline pH values at low and ambient temperatures. On the other hand, Tukey’s test indicated higher reductions in cake moisture at higher temperatures for lower pH values. This study affirms the need to monitor and control the pressure filtration process as throughput could significantly vary with changes in temperature and slurry conditions.

By G. S. S. Raman, M. S. Klima

Coal refuse slurries stored in tailings impoundments can potentially lead to environmental concerns such as effluent seepage, property devaluation, and in extreme cases, dam failures. Pressure filtration offers an opportunity to reduce the impoundment requirements by providing significantly drier solids. A full-factorial design was used to study the effects of temperature and pH on dewatering a refuse slurry obtained from a coal preparation facility in Pennsylvania, USA. The experimental results indicated a strong effect of temperature on cake moisture as the cake moisture after about 2800 s was 22% at 43 °C and only 36% at 10 °C for tests conducted at pH 3. ANOVA results confirmed the statistical significance of pH, temperature, and their interaction effect. Also, the results showed no significant differences between the tests conducted near neutral and alkaline pH values at low and ambient temperatures. On the other hand, Tukey’s test indicated higher reductions in cake moisture at higher temperatures for lower pH values. This study affirms the need to monitor and control the pressure filtration process as throughput could significantly vary with changes in temperature and slurry conditions.

By James L. Weeks

Introduction This paper attempts to summarize some of the major criticisms of drug testing. Eight problems with drug testing are discussed. These are: • It does not measure something employers have a reasonable need to know, • It is a distortion of priorities, • Drug use is not known to be associated with increased risk of occupational injuries, • Drug testing is proposed as a dangerously simplistic solution to poorly conceived problems, • In the absence of safeguards, it is unacceptably inaccurate, • In the absence of treatment commitments and confidentiality protection for persons dependent on drugs, it is an unethical practice of medicine, • Drug testing is an invasion of privacy, and • It will have a negative effect on treatment of persons with drug or alcohol dependencies. Employers' need to know It does not measure something employers have a reasonable need to know. It is reasonable for employers and fellow workers to want to know if workers are functionally impaired (intoxicated) while on the job. Drug testing does not measure impairment. It measures the concentration of drug metabolities in urine or blood. Unlike measurements of blood alcohol concentration (BAC), drug metabolites are not correlated with impairment or intoxication. They indicate only drug use in the one to two weeks before a urine sample. And, in some instances, they indicate chronic use. Impairment caused by drug use, on the other hand, occurs immediately and declines rapidly within hours. Drug metabolites may linger for days afterwards. Drug metabolite concentrations in urine are a function of (Morgan, 1984; Schartz and Hawks, 1985; MMWR, 1983): • the amount and purity of drug consumed before taking the test, • when the drug was consumed, • whether the person was a chronic user, in which case a certain amount of drug metabolites would be stored in body fat and slowly released, • the person's metabolic rate, and • for metabolites in urine, any dilution effects of urine. Only the first two factors has

Jan 11, 1987

By James H. Dye, N. E. Norman

There will be about 300 raise boring machines used worldwide by late 1981, attesting to the acceptance of this drilling system by the mining and construction industries. Over the past few years, many articles have cited the advantages of raise boring: •improved safety; •faster completion of the raise; •elimination of sublevels; •cost reductions; •better structural characteristics of the opening; •labor reduction; and •noise abatement. The relative importance of each advantage varies from mine to mine. When analyzing the total economics of raising, each advantage must be considered. The factors having the most effect on economics are fixed costs, direct costs, and comparative savings versus conventional methods.

Jan 3, 1981

By Gregory R. Gorrell

The legal issues surrounding the regulation of subsidence are among the major concerns facing the underground mining industry today. Whether subsidence occurs almost immediately as a result of longwall mining or without warning as a result of room and pillar mining conducted years ago, the resulting disputes are highly controversial and typical of the disputes involving the competing interests of surface and mineral estate owners. Until recently, the law governing these disputes was firmly established under the common law. The passage of the Surface Mining Control and Reclamation Act 1, the utilization of new mining technologies, and the general heightened environmental awareness of our times, however, have interjected new issues into this area of the law. State and Federal court decisions and administrative agency interpretations have helped clarify some of the issues. However, as evidenced by the many recent lawsuits between operators, surface owners, and regulatory agencies, many uncertainties still exist.

Jan 1, 1986

By Rudy Scarabelli, John R. Wagner

At one time explosives were the only economical means of rock tunnel excavation. Except in relatively long tunnels in the right rock explosives are still the cheapest means of rock excavation where they can be used. Today the most economical means of rock tunnel excavation is increasingly not the choice of the contractor. A good part of our work is for public agencies in urban areas and the public today is increasingly less tolerant of the disruption caused by our efforts. Owners in many cases have to direct their engineers to write specifications which severely restrict noise and vibration levels during construction. Sometimes specifications allow drill-and-shoot for starter tunnels only or even eliminate powder by fiat. Recent advances in the use of explosives such as sequential firing have made blasting more palatable to the public but are not enough in all situations. Thus the roadheaders on construction projects. In recent work I have seen the Alpine Miners, a Paurant Miner and the Robbins Mobile Miners used in several rock formations and now believe this type of equipment has a place in the tunnel constructor's choice of equipment. Rudy and I have not attempted to present a formula for choosing the best alternative excavation method in any given case because, of course, of the variables involved. We have simply tried to describe our experiences on a particular project and hope our observations will be of some value to tunnel constructors.

Jan 1, 1987

By J. Sammarco

Proper illumination is critical to a miner?s ability to detect hazards in underground mines. Moving hazards are often located in the miner?s peripheral field-of-view, while slip/trip/fall hazards are often located in the forward field-of-view. The objective of the research described in this paper was to determine if light-emitting diodes (LEDs) improve visual performance as compared to traditional incandescent (INC) cap lamps. The research presented focuses on comparative studies of a National Institute for Occupational Safety and Health (NIOSH) prototype LED, a commercial LED, and an INC camp lamp. Thirty subjects participated in these studies; ten subjects in each of the age groups: 18 to 25 years, 40 to 50 years, and 51+ years. Visual performance was quantified by the subjects? speed and accuracy in detecting hazards, while visual performance for disability glare was quantified by the use of contrast sensitivity tests. Results suggest that LEDs with a visible spectrum containing a higher concentration of the shorter wavelengths can enable visual performance improvements with respect to disability glare, the detection of moving hazards in the peripheral field-of-view, and the detection of floor hazards in the forward field-of-view. The NIOSH prototype LED cap lamp provided the best visual performance improvements for the older age groups in every test. Disclaimer: The findings and conclusions in this report have not been formally disseminated by the National Institute for Occupational Safety and Health and should not be construed to represent any agency determination or policy.

Jan 1, 2009

By David Hopkins, Steve Klein, Bradford Townsend, Ed Sum, Derek Penrice

INTRODUCTION The Transbay-Caltrain Downtown Extension (DTX) Project involves the construction of an approximately 1.5-mile rail line that will extend Caltrain commuter service and the future California High Speed Rail system into downtown San Francisco. The underground rail extension will be constructed by mined tunnel and cut-and-cover methods. Tunneling challenges include difficult ground conditions, low rock cover, the presence of historic buildings along the alignment, and the large tunnel span, ranging from approximately 50 to 65 feet. Three mined tunnel construction methods were evaluated: the Stacked Drift Method, the New Austrian Tunneling Method/Sequential Excavation Method (NATM/SEM), and Tunnel Boring Machines (TBM). This paper describes the challenges presented within the mined tunnel section, and summarizes the evaluation of tunneling methods that led to the selection of NATM/SEM. PROJECT OVERVIEW The existing Transbay Terminal opened in downtown San Francisco in 1939. This facility is antiquated, and does not meet current building seismic safety standards or the transportation needs of the Bay Area. For these reasons, San Francisco voters approved Proposition H in 1999, which proposed to construct a new or rebuilt regional transit center at the site of the existing terminal and extend Caltrain commuter rail ser-vice to the new transit center. The new transit center is the hub of the Transbay Transit Center (TTC) Program, which will greatly enhance regional transit service by providing connectivity for six Bay Area transit providers at one facility. The program will be the largest inter-modal centerwest of New York City. The TTC Program is comprised of two major projects, the Transit

Jan 1, 2007

By Shaoxian Song, Ling Xia, Hongqiang Li, Yubiao Li, Yunliang Zhao, Shaobing Xie

Since human daily demands for fresh water have been increased significantly, the supply of fresh water for the mining industry, especially froth flotation, should be considerably reduced. In addition, stricter environmental standards have been implemented in many countries to reduce the risks due to the disposal of wastewater, many flotation operators have to seek more efficient ways to utilize the limited fresh water sources. Recycling water with high concentrations of impurities is a normal strategy for most of the mineral processing plants; however, water quality should be carefully considered to guarantee a smooth flotation process. Recently, the application of seawater in flotation has attracted much attention due to its availability and abundance rather than fresh water. However, the influencing mechanisms due to the application of seawater in flotation have not been fully understood especially the reactions between mineral particles and bubbles in the presence of high concentrations of cations and anions. This would impede the application of alternatives to fresh water in the flotation. Therefore, this paper reviews the current water sources and the technologies for water recycling in the flotation process. Specifically, the life cycle of water in flotation was proposed. In addition, the strategies including high pulp density flotation as well as the most promising alternatives to fresh water have been discussed in details, with the related mechanisms being demonstrated.

By D. Bernabe

The mine scheduling process defines a mining sequence across the life of the mine and stipulates the amount of ore, waste, and specific blocks to be mined each year so that the highest economic return can be obtained under a number of constraints. There are a number of mine scheduling software packages available. Each claims to be the best scheduler by maximizing Net Present Value (NPV) or by minimizing overall mining costs. These mine scheduling programs follow different procedures and scheduling philosophies based on either mathematical or heuristic principles. There was no study in which the mine production scheduling procedures applied by these packages were discussed and compared. This paper evaluates four open pit mine scheduling programs recently developed and compares them in order to determine if significant differences exist among them. The same input data, which consist of a 3-D block model, an economic set of parameters, and the initial surface topography for a operating copper mine in Southern Peru, was used to test each technique. The following programs were investigated with respect to their ability to optimize the NPV for the case study. 1) M821V1 Scheduler by Mintec; 2) NPV Scheduler by Earthworks; 3) Milawa Scheduler by Whittle Programming; and, 4) Fundamental Tree Scheduling Method (FTSM) developed at the Colorado School of Mines. The results from this case study demonstrate that the scheduling software packages, Mintec, Earthworks, and Whittle obtained similar NPV’s, while FTSM scheduler gave a six percent higher NPV than the other schedulers.

Jan 1, 2002

By Behrouz Tehrani

The size, complex issues, and requirements to construct large number of tunnels, for a single project, expeditiously, and without exceeding the overall project budget, a program Construction Management (CM) team is highly recommended to be selected early during design process to provide guidance/direction relative to contract packaging and scheduling. This paper is not focused on the project itself, however, the emphasis is on experiences gained from the project. Wishing that some of the strategies described in this paper will be of value to owners of underground project.

Jan 1, 2008

Twenty field-scale tests were conducted in a 28 MW pulverized coal power plant in Healy, Alaska, to examine mill power consumption in relation to coal grind size. The intent in this field-scale study was to verify if grind size truly impacted power consumption by a detectable amount. The regression model developed from the data indicates that grind size does impact mill power consumption, with finer grinds consuming significantly more power than coarser grinds. However, other factors such as coal hardness (i.e., the lower the Hardgrove Grindability Index, or the harder the coal, the higher the power consumption) and mill throughput (i.e., the higher the throughput, the higher the power consumption) had to be included before the impact of grind size could be isolated. It was also observed that combining amperage and flow rate into a single parameter, i.e., specific amperage, hurt modeling. Cost analysis based on the regression model indicate a power savings of $19,972 per year if the coal were ground to 50% passing 76 mm rather than the industry standard of 70% passing 76 mm. The study also demonstrated that size reduction constituted a significant portion of the power consumption.

Jan 1, 2008

The failure of a seal in an underground coal mine can have devastating consequences. Traditionally seals have been constructed as flat walls. Large hydraulic dams, on the other hand, are constructed as concave arches. This paper presents an initial analysis of the potential strengthening of seals by concave construction as well as the impact of additional cost in terms of labor and material. A simple finite element analysis of three-dimensional solids under uniform loading allows comparisons between the strength of a flat wall and a curved arch. The models are examined for reasonable behavior and displacements at 20, 50, 100, and 200 psi loads.

Jan 1, 2007

By Joseph Clare, Elizabeth Anderson, Mike McGinley, Ron Hines, Judy Cochran

The South Lake Union Pipelines contract for King County Wastewater Treatment Division and Seattle Public Utilities in Seattle, Washington included three 1.8 m (72-in)inside diameter microtunneled pipeline segments totaling about 793 m (2,600 lf).Tunnel alignments were within street right-of-way of heavily traveled urban roadways. Project challenges recognized in the design included: high groundwater levels; contaminated soil and groundwater; variable soil conditions, including fill; and timber piles and other obstructions remaining from historic land uses. The tunnels were built using a Lovat MTS Microtunneling machine, beginning in spring 2003. Conditions encountered during construction presented additional challenges beyond those anticipated in the design process, and were successfully addressed by the owners, designer, and construction management consultant all working with the contractor. Problems included highly variable soil conditions, cracking of reinforced concrete pipe joints during pipe jacking, a timber pile trestle uncovered during shaft construction, and obstructions encountered in the second and third microtunnel runs.

Jan 1, 2005

By Erich J. Jacob

In the past 15 years the enforced improvement of the public traffic systems caused a boom in urban tunnel construction. In 1961 the City of Paris started to build the Express-Metro. Of the 47 km long double-track line crossing the city center, nearly 45 km are in operation since 1971. Still missing is here only an about 2.6 km long connecting stretch, which is under construction now. From 1963 to 1969 the 21.8 km long Victoria Line was built in London as extension of the existing network,. A little later, in the years 1965 to 1973, the City of Hamburg supplemented its subway network by the construction of a 16.8 km long line between the Boroughs of Billstedt and Stellingen. Also in 1965 the City o Munich started to build a subway system of 54 km f length. Thereof a stretch of 16.2 km could be taken into operation in 1972 shortly before the Olympic Games. These are only some of the better known projectsas examples of the activities in European cities. In nearly all cities with more than about ½ million inhabitants subsurface traffic lines were begun or supplemented. Furthermore, numerous undercuts or other subsurface structures were built. The Ij Tunnel in Amsterdam and the new Elbe Tunnel in Hamburg may be mentioned, both structures finding international attention.

Jan 1, 1976

By K. E. Livo, D. H. Knepper

Modern remote sensing provides a means for locating and characterizing exposed mineralized systems in many parts of the world. These capabilities are non-invasive and help target specific areas for more detailed exploration. An example of how remote sensing technology can be used is evident from a study of the Questa Mining District, New Mexico. Analysis of low spectral resolution data from the Landsat Thematic Mapper satellite system clearly shows the region-al distribution of two broad mineral groups often associated with mineralized systems: clay-carbonate-sulfate and iron oxides-iron hydroxides. Analysis of high spectral resolution data from the Airborne Visible and Infrared Imaging System (AVIRIS) shows the occurrence and distribution of many individual mineral species that characterize the pattern of hydrothermally altered rocks in the district.

Jan 1, 2004

By Tom Szaraz, Steve Skelhorn

Part of a major sewer expansion for the City of Columbus, Ohio. The Big Walnut Outfall Augmentation Sewer (BWOAS) consists of 4,000m (13,200 ft) of 3.66m (12 ft)diameter tunnel passing mainly through glacial deposits with a water head of up to 2 bar. The project involves many new innovations, including: Slurry wall work shaft with excavation below the water table; Hybrid universal rings combining traditional steel reinforcement with fibers; New, full EPB Lovat TBM; Two component grout system pumped to the TBM from the surface; and, Linabond corrosion protection liner. The paper looks at the planning approach adopted to meet the various challenges presented, combined with an overview of progress to date.

Jan 1, 2007

By Bengt L. Stillborg

INTRODUCTION This paper summarizes the result of a two and a half year research program. The objective of the research was to develop a fundamental understanding of the Rib-in-Roc method. Through the development of a new model technology, namely three-dimensional physical models which powerfully exploit the results of dimensional analysis Stillborg, Stephansson and Swan (1), it has been possible to establish the contribution to both permanent and immediate stabilization of a large underground opening pre-reinforced by the Rib-in-Roc method. Using the results from these physical models and earlier work by Stillborg and Stephansson (2) and Åkesson (3), a conceptual synthesis is given in this paper so demonstrating the Rib-in-Roc method to be a practical working system of pre-reinforcement. DESCRIPTION OF THE RIB-IN-ROC METHOD To give the reader an idea of how this method of pre-reinforcement is performed, a short description will be given, Figure 1. Before any full-scale excavation takes place an entry is made in the host rock and rib raises are driven around the proposed opening. These raises are made at a spacing that is dependent upon rock quality; an opening in poor rock needs more ribs per length of opening. As the ribs are driven they are used as a site from which very competent rock bolting can be done. As a rib is excavated it is filled with reinforced concrete. Finally after having in this way reinforced the zone around the proposed opening, (a reinforced arch is formed) the displacements are automatically controlled as the opening is being excavated. Using this method openings with a span of 50-60 meters (160-200 ft) and a height of 60-80 meters (200-260 ft) are likely to be realised.

Jan 1, 1979