Search Documents

By J. O. Mogalanyane, N. Naudé, A. M. Garbers-Craig

The fines produced is not suitable as feed material for the subsequent rotary kiln and the electrical arc furnace. The need for briquetting the ferronickel ore is premised on the minimisation of fine particles in the rotary kiln as well as improving charge permeability in the furnace, and improving overall process safety. Briquetting may be defined as an agglomeration method in which fine particles are compressed under pressure. It consists of three different technologies: vibropressing, roller pressing and stiff extrusion. The current study focuses on evaluating the performance of ferronickel briquettes generated, using roller-pressing technology. Physical properties, chemical properties and metallurgical properties of the briquettes were used to evaluate their performance and quality. Standard ISO tests for iron ore pellets were used. Size degradation as a result of reduction was measured using the ISO 4696-1 test. The decrepitation of the briquettes at the point of entry into the rotary kiln was evaluated using the ISO 8371 test method at a temperature of 700oC. The degree of reduction was evaluated using the ISO 4695 test procedure. Average green briquette compressive strength of 559 N was reported at a moisture content of 16% with an average drop number of 19.1. Increasing the moisture content has a detrimental effect on both the compressive strength and the green briquette yield. The drop number is expressed as the number of drops until breakage, when a briquette is dropped from a 1 m height, decreased with an increase in moisture content. At a moisture content of 16% an average green briquette yield of 85.1% was reported. Keywords: Ferronickel briquettes, moisture content, curing conditions, physical properties, chemical properties

Jan 1, 2020

By D. Saramak, T. Gawenda, A. Stempkowska, Z. Naziemiec

The aim of the paper is to discuss the possibility of producing aggregates with an increased content of regular particles, as well as to present a method of aggregate production which has not previously been used in the industry. Traditional aggregate production circuits require the application of three or four grinding stages (depending on the particle size of the feed), but for fine particle fractions of aggregates, irregular grains occur on average with a content of 10%. The innovative technological circuit can produce the aggregates with the content below 3%, even in a single- or two-stage crushing circuit. Downstream jig beneficiation of such prepared material results in higher separation sharpness, lower probable error index (Ep) and imperfection (I). Keywords: Aggregate production, jig beneficiation, mineral processing, raw materials

Jan 1, 2020

By D. Minson, G. Lindner, S. Miskovic

Thickening is an essential process in the mining industry and currently one of the most costeffective technologies for recovering water from tailings streams. Improved performance of thickeners can lead to significant energy savings, and increased recovery of water close to the mill. Its performance is directly affected by the rheological properties of slurry at the raking zone. To further understand the dynamics of slurry inside thickeners, a multiphase particle-in-cell method (MP-PIC), is used to investigate its behaviour on a sliding channel. Parameters like particle-size distribution (PSD), rheological properties, and domain discretisation were benchmarked to study its influence on highly dense flows. The slurry concentration by weight of the samples ranged between 60 to 70% of solids by mass, under which conditions it is known to behave like a non-newtonian fluid. An experimental flume, 0.2 m wide and 2 m long, was used for validation under different angles and slurry composition. Visual analysis of the slurry height and shape, as well as velocity measurements, were compared with numerical data. The preliminary results show the ability of MP-PIC method to represent different types of highly dense flows, while still being computationally affordable and practical for industrial use. Keywords: High density thickener, CFD, MP-PIC, multiphase-flow

Jan 1, 2020

By O. T. Konina, V. A. Masloboev, A. V. Svetlov, E. A. Krasavtseva, D. V. Makarov, A. A. Goryachev

Dusting phenomena have been examined at the tailings storage facility of Apatit JSC Kirovsk, a mining operation located in the far north of the Russian Federation. The material composition of the tailings was identified. Existing dust suppression methods were examined. Field observations were undertaken and official data was obtained from the Murmansk Administration for Hydrometeorology and Environmental Monitoring, and analysed. A database was built for forecasting dusting according to critical scenarios in order to estimate the peak MPCs of suspended solids in the atmospheric air. Mitigation measures were formulated and recommended to the mining operation. Keywords: Mineral dust particles, apatite-nepheline ore concentration tailings, suspended solids MPC, climate change

Jan 1, 2020

By J. Bal, V. D. Dao, W. Li

"SynopsisThis study proposes a methodology for evaluating the risk of coal bumps in multiple-seam longwall mining. Both the stress field and the total energy release (TER) during retreat were evaluated in the specified case involving multiple-seam mining using the LaModel program. The results of numerical simulations indicated that both the peak vertical stresses on the panel edges and the peak TERs in the outby longwalls increased significantly as the horizontal offsets were reduced from 60 m to zero. With the comprehensive consideration of the stress field and TERs, a conservative offset of 60 m was ultimately adopted when developing the gateroads of the lower panel in the field. The field measurements indicated that coal bumps were avoided completely by employing the proposed design, and the maximum roof-to-floor and rib-to-rib convergences of the tailgate during retreat were only 360 mm and 576 mm, respectively.IntroductionCoal bumps – sudden, violent bursts of coal – pose a serious threat to the safe excavation of coal. Their occurrence depends on the properties of the surrounding rocks, stress field, and dynamic disturbance. The complexity of the mechanism of coal bumps is further enhanced in multiple-seam mining due to seam interaction. Multiple-seam mining is most frequently found in the coalfields in eastern China, such as Xuzhou, Xinwen, Zaozhuang, and Huainan. In the past, due to issues of availability, economics, and ignorance of the potential risk in multipleseam mining, coal seams in such conditions were mined without proper planning to account for seam interaction. Fortunately, studies published over the past three decades have raised awareness of the problems associated with multiple-seam mining, and indicated that the ground control issues induced by multiple-seam mining can be avoided and/or minimized with proper planning.A number of technical studies pertaining to the design of multiple-seam mines have been published. These studies can be divided into two groups based on their methodologies of design: empirical (Chekan and Listak, 1993; Haycocks and Zhou, 1990, Matetic et al.; 1987a, 1987b) and numerical approaches (Li et al., 2000; Maleki, 2007; Mark, 2007; Peng, 2007; Zipf, 2005). The majority of the extant studies on the interaction mechanisms in multiple-seam mining have focused on the load transfer during operation, resulting in the proposal of the pressure bulb theory (Forrest et al., 1987; Haycocks and Karmis, 1983; Peng, 2008; Peng and Chandra, 1980) and pressure arch theory (Holland, 1973; Oram and Ponder, 1997) to guide multiple-seam mine design. However, neither, of these theories can be used to evaluate the potential for coal bumps."

Jan 1, 2015

By G. Sánchez, S. Seiler, B. Klein, T. Cebeci, P. Bradshaw

The Decar Nickel District is a greenfield discovery by FPX Nickel Corp., of nickel mineralisation located in central British Columbia (BC), Canada. The Baptiste deposit is part of the Decar Nickel District and is a unique deposit containing a nickel-iron alloy mineral called awaruite, with over 2-billion tonnes of inferred resource grading 0.12% Davis Tube Recoverable (DTR) nickel. This deposit represents a significant nickel resource. Awaruite is a high density and ferromagnetic mineral, which could be recovered, along with magnetite that is also present in the samples, using magnetic separation. However, there is still a lack of understanding of the properties of the awaruite and its metallurgical response. This information is imperative for the set-up of the variables involved in its concentration. The aim of this paper is to show and discuss the effect of magnetic field strength for the recovery of nickel from Baptiste deposit samples. Magnetic separation at bench and pilot scale with different magnetic field strengths is evaluated as a concentration method for awaruite. Mineralogical information is provided to support the results and also to briefly assess the variability of DTR nickel within the deposit. The Baptiste deposit is unique and will benefit from a sound scientific understanding of the process solution as well as other ongoing work. If successful, the outcome will lead to the development of a mine. With greater than 2-billion tonnes of inferred resource, the mine would represent a significant new source of nickel globally. Keywords: Nickel ore processing, magnetic separation , awaruite, magnetite

Jan 1, 2020

By Y. Cao, C. Li, A. Song

Bubble size plays a key role in determining flotation efficiency. Bubbles can be formed by passing air through pores. Bubble detachment from a pore is driven by lifting forces including buoyancy force and momentum force. Enhancing the momentum force is the key to accelerate bubble detachment and to minimise bubble size. Recent studies show that replacing steady air with oscillatory air supply could significantly decrease bubble size by enhancing the momentum force. To date, the underlying mechanism for the improved momentum force with oscillatory air supply is not yet clear. This work, for the first time, developed a qualitative model for the momentum force as a function of frequency, on/off time ratio and gas flow rate. It was found that the momentum force was positively correlated with the frequency as well as the air flow rate, and was negatively related to the on/off time ratio. The relation between bubble size and these operating parameters was also investigated. Keywords: Flotation, bubble size, momentum force, modelling, oscillatory air supply

Jan 1, 2020

By F. K. Crundwell

The rate of dissolution of sulphide minerals is frequently interpreted in terms of the passivating behaviour of a layer of material on the surface. This interpretation has driven research to identify and possibly remove this layer from the surface, and thus yield higher rates of dissolution. The identification of such layers has proved difficult, with different researchers claiming different compositions for possible layers. An alternative framework has been pursued by the author and co-workers, who have argued that the rate of dissolution is governed by the electronic structure of the minerals which give rise to their semiconducting properties. Researchers sceptical of this approach have argued that semiconducting properties are only important in highly pure substances. In this paper, we review the electronic and semiconducting properties and discuss how they impact dissolution behaviour. These properties affect their colour and dissolution properties even though the minerals are not high purity substances. Keywords: Dissolution, leaching, passivation, semiconductor, chalcopyrite

Jan 1, 2020

By L. Gutierrez, R. Yepsena

Enargite in porphyry copper deposits is an important mineral as it displays good floatability under the presence of the collectors usually used in the flotation of copper sulfides. As a result, copper concentrates grades are reduced. As scarcity of water resources is a problem relevant to Chilean mining, the use of seawater is a feasible solution. The behaviour of copper sulfides and molybdenite in the process of flotation in seawater was previously studied but not for enargite. The objective of this research is to study the behaviour of the enargite in different conditions of electrochemical potential during the process of flotation using seawater. The study was carried through micro-flotation tests using pure samples of enargite, at Eh values ranging from -300 to 500 mV(SHE), both in seawater and aqueous solutions containing calcium and magnesium. The results show that at pH 10.5 in seawater, the enargite and chalcopyrite recoveries are reduced throughout the whole range of Eh studied. At pH 9 in seawater, enargite and chalcopyrite are depressed under reducing and slightly oxidising conditions. The recovery of both minerals drastically decreases at Eh values lower than -100 mV and greater than 400 mV. The behaviour of enargite in seawater flotation differs from that observed in conventional water, since in the latter case the recovery of enargite decreases at higher potentials close to 500 mV. Keywords: Enargite, flotation, seawater, redox potential

Jan 1, 2020

By A. Singh, R. R. Maclachlan

SYNOPSIS A back-analysis procedure based upon 35 mm photography was developed on a laboratory scale for the pur¬pose of determining the percentage of oversize particles known to be present in heaps of fragmented rock. Eight simple blends of crushed stone containing varying percentages of oversize on a 1:40 modelled scale were examined. Simulated test conditions for the following were subjected to the photographic study: (1) a bench heap, (2) the surface exposure of a partially excavated heap, (3) a gravity-sorted surface as occurs on an apron dump, and (4) four quadrant views of an incrementally built conical heap of rock fragments. The best back-analysis determinations were obtained from (4), the cone, over all eight blends of fragments. The mean error was within -0,16 per cent of the true value, with a range of ± 1,872. This was for oversize contents of 5 to 20 per cent where a minimum 25 per cent of the photograph area was processed by digitizer. The worst results were from the apron dump at - 1,462 per cent for a mean error of ± 4,174 per cent. The intermediate results were from the undisturbed bench at -0,186 per cent with a mean error of ±2,862 per cent.

Jan 1, 1989

By A. J. Burger, F. L. D. Cloete

Tests indicated that effective recovery of pyrite from a coarse Witwatersrand quartzitic ore can be accomplished by intensified flotation in an air-sparged hydrocyclone. Air is fed through the porous cylindrical wall of the hydrocyclone into a swirling layer of slury. Hydrophobic particles are attached selectively to small air bubbles, which form a froth and are recovered through the overflow. Hydrophilic particles pass out in the underflow. A spigot in which flow is restricted by an orifice was found to be more successful in preventing blockage by wood chips than an annular opening between a pedestal and the cylinder wall. Pyrite recoveries of 85 to 93 per cent at grades of 35 to 40 per cent sulphur were obtained in the air-sparged hydroclone with residence times of about 1 second. Comparative tests in a batch flotation cell after 320 seconds yielded average recoveries of up to 96 per cent, but with a mean grade of 32,5 per cent sulphur. A high colector dosage of 120 g/t was required in the cyclone, compared with the 40 gft used in conventional operations. An air flowrate of about 150 I/min was adequate at a slury feed rate of 35l/min. Particle sizes between 38 and 106µm yielded the best flotation results.

Jan 1, 1988

By N. J. Roodt

Mine dumps created in terms of the pre-MPRDA regime (old order mine dumps) are currently not regulated by the MPRDA, and the common law owners of such dumps are free to process them without the need to obtain the relevant rights. The MPRDA Amendment Act purports to change this position. However, the wording of the Amendment Act raises a number of problems which render the post-amendment position at best unclear and at worst absurd and unworkable. The primary concern with the Amendment Act is that, on one interpretation, material placed on the same dump at different times may be treated differently at law. Thus, parts of a dump may be subject to one person?s right while others may be subject to another?s right. Moreover, case law has generally regarded mine dumps as movable property and, by extending the MPRDA to apply to all mine dumps, the Legislature is extending the ambit of the Act to cover movable property, a scenario not contemplated by the wording of the Act (even after its amendment) in relation to applications for rights. The better interpretation of the amendments, which are not yet in force, is that they will not apply retrospectively to old order mine dumps.

Jan 1, 2010

By I. Ashmole

The dimension stone industry is not widely known or appreciated within the mainstream mining industry. This is in spite of the fact that the industry has grown at an average of over 7% per annum since 1980, and is estimated to now have a global turnover in excess of US$ 60 Billion per annum. Production technologies, particularly in the developed world where labour costs are high, have developed rapidly over the past two decades. Aligned with this, there has been a significant trend in adoption of a more professional mining approach in the exploration for and operation of dimension stone quarries. In fact, in the experience of the authors, mining a dimension stone deposit successfully if often more challenging from a mining engineering point of view than many conventional surface mines. This paper gives an overview of the industry and then proceeds to discuss best practice in exploration for dimension stone and to outline the latest technologies applied in mining of dimension stone. These technologies are varied and the specific combination of technologies applied in any given quarry is determined by both the physical properties of the material as well as the influence of geology which significantly impacts on the recovery of saleable material and hence the economics of the quarry.

Jan 1, 2008

By S. M. Graham, G. Mellis

"The determination of the oxidation state(s) of an element present in a solid sample may be required for a number of reasons, including the assessment of the degree of reduction which has taken place during a multi-step production of a metal. In addition, possible flaws in a metal may result from small amounts of oxides included in the solid. The analyte of interest may be present as a major component of a sample of interest, or as a minor impurity - beneficial or requiring removal - in another matrix.Numerous methods have been established for the analysis of species in solution samples - for example, Fe2+ and Fe3+ by titration, Cr6+ by colourimetric means, etc. With appropriate knowledge of the solution being analysed, many of these methods are fairly straightforward, extremely reproducible and accurate. In those instances where the analyte in a solution is known to be in only one form, the analysis is even more straightforward, since it can be achieved instrumentally (by AAS, rCP-OES or rCP-MS, for example).However, the situation with respect to the analysis of solids is not as simple. Various techniques - such as X-ray diffraction - are routinely used by our mineralogists to obtain information about the various minerals present in solid samples, and thus about the oxidation states of the analyte elements present. However, these techniques usually give results that are qualitative, or semi-quantitative at best. They are also usually time-consuming and expensive. One of our colleagues at Mintek, Deshenthree Chetty, has done extensive work in developing a method for the quantification of manganese species in solids using mineralogical methods, and this is no small achievement."

Jan 1, 2014

By N. Hamlef

In this study, the effects of heat treatment on phase formation and surface morphology of the Cr-Pt coated system are investigated using X-ray diffraction and electron microscopy techniques. The CrPt andCr4Pt (Cr3Pt - A15 type) phases were formed after heat treatment of the coated samples. Heat treating at 1000°C renders a distinct island coating morphology that is non-continuous in nature. A diffusional model is proposed for this coated system with regards to the surface morphology formation after heat treatment.

Jan 1, 2014

By E. K. Mutinda, D. K. Maina, R. M. Kasomo, B. O. Alunda

Assessment of blast fragment size distribution is critical in mining operations because it is the initial step towards mineral extraction. Different empirical models and techniques are available for predicting and investigating the consequences of blasting, one of which is the Kuznetsov Cunningham-Ouchterlony (KCO) model. In this paper we summarize the advances in the empirical models from inception until now, and explore the improvements that have been made so far with particular emphasis is on the most recent KCO model. Utilization of the model and the errors that arise between expected and the actual outcomes are analysed. The results indicate that the KCO model remains useful for predicting the blast fragmentation at limestone mine sites, despite the availability of other advanced prediction models. It is also a valuable instrument for pre-surveying the impact of varying certain parameters of a blast plan.

Mar 1, 2021

By S. Banisi, A. Ghasemi, A. Fazeli, M. Rezaei, M. Maleki-Moghaddam

The efficiency of high capacity SAG mills which consume large amounts of energy depends on the grinding and slurry discharge systems. A 9.7 m × 4.8 m SAG mill with radial pulp lifters is used at the Sarcheshmeh copper complex grinding circuit. The process audit indicated that the pulp discharge system was not efficient, judging by the amount of slurry flow back and carry over. These events limited the discharge rate and increased the wear rate of the lifters and grates. With the objective of finding a new design for pulp lifters, a 3D DEM software (KMPCDEM ©), along with the plant operational data and photographic evidence was used. The KMPCDEM © software was used to compare the efficiency of the radial and curved pulp lifter design based on the material flow. The slurry flow was analysed in terms of ease of discharge and lifter wear rate. It was found that changing the radial pulp lifters to curved pulp lifters could improve the discharge efficiency,and decrease wear rate of the pulp lifter in particular at the base of the pulp lifters. The simulation results showed that if curved lifters with a radius of 0.3×mill radius are used, the amount of slurry flow back and carry over will be negligible. It is predicted that by installing the curved pulp lifters, the capacity of the mill increases by 10% and the pulp lifter service life improves by at least 20%. Keywords: SAG mill, radial pulp lifter, DEM,curved pulp lifter, Sarcheshmeh

Jan 1, 2020

By K. Cole, D. Mesa, P. R. Brito-Parada, M. R. van Heerden

Turbulence in stirred tank flotation vessels determines the bulk transport of particles and has an important role in particle-bubble collisions necessary for attachment. Positron emission particle tracking (PEPT) produces quantitative measurements of the kinematic motion of different particle classes inside flotation vessels. This paper presents flow profiles of the vessel, residence time distributions, flow profiles through the mesh and macroturbulent kinetic energy distributions as experienced by valuable (hydrophobic) mineral particles in a laboratory scale flotation vessel. The results highlight the impact of the rotor-stator design and a retrofit mesh modification at the upper part of the vessel which improve recovery by decreasing turbulence in the quiescent zone and at the interface. Keywords: Flotation machines, turbulence, PEPT

Jan 1, 2020

For the past 12 years, the Universities of Stellenbosch and Cape Town have hosted an annual symposium to discuss research topics in Minerals Processing. Since 1987, this meeting has been held under the auspices of the Western Cape Branch of the South African Institute of Mining and Metallurgy, and has enjoyed much national and international support. In 1993, in place of the usual Symposium, the Branch and Universities collaborated with CSM Associates Ltd and Minerals Engineering Journal is organizing the international Minerals Engineering '93 Conference in Cape Town.

Jan 1, 1993

By G. van Aswegen

The geometry and morphology of a set of low-angle fractures around a stope in a deep Witwatersrand gold mine are explained in terms of extension fractures forming under variable conditions of stress. Primary extension fractures (E1) form some distance ahead of an advancing stope along the s1, s2 plane. With stope advance, a couple of these fractures end up in a stress regime conducive to transpressional shear and a secondary set of extension fractures(E2) is formed at a high angle to the primary fractures. i.e. at a low angle to the stope. As the E2 fractures are undermined, they migrate into a stress regime of transtensional shear and a third set of extension fractures (E3) may develop between E2 fractures. These have sigmoidal shapes, being parallel to the E2 fractures at the E2 discontinuity where s3 is negative, and curved through the unfractured rock between E2 fractures where s3 is positive at the instant of fracturing. The fractures all display fractographic features characteristic of dynamic extension failure with striae indicative of the direction of rupture propagation and the local, instantaneous orientation of s1.

Jan 1, 2012