Search Documents

By J. O. Claassen

"Homogeneous populations are required to perform descriptive, probabilistic, and inference statistics and to support stable, predictable mining operations. The geological and downstream processing environments are, however, highly heterogeneous. The complex nature of mining environments requires means to identify and define multipopulation environments that could affect the performance of mining value chains. A study performed at several operating mines suggests that the impact of heterogeneous or variable geological, mining, and plant processing environments on overall mining value chain performance may not be a key focus area at these operations. This was illustrated through the use of basic and spatial statistics, which included the log-probability plot, a modified range equation, and chronovariography. The findings reflect high relative variability in the geological and processing environments studied and mining operators’ inability to effectively deal with the sources and consequences of variability. The study suggests that a focus on heterogeneity in complex mining operations may significantly enhance overall mining performance. IntroductionHeterogeneity and why it mattersHeterogeneity refers to a state or quality of being variable/diverse and comprising different non-compatible elements or parts. In statistical terms a heterogeneous population can refer to a population comprising different non-compatible sub-populations or a multipopulation environment. The latter is commonly found in natural environments such as geological environments (Bardossy and Fodor, 2001). The inherent heterogeneity of complex geological environments is also referred to as spatial heterogeneity. Heterogeneity or variability, however, also occurs over time at mining operations. A case in point is variable ore composition on a conveyance system feeding a processing plant or product stockpile.Heterogeneity associated with the mining environment can significantly influence key aspects of day-to-day mining operations such as sampling, the use of descriptive, probabilistic, and inference calculations, and an operation’s ability to manage and control the mining value chain as a whole."

Jan 1, 2016

By M. A. Mahboob, T. Celik, B. Genc, I. Atif, S. Ali

"Mapping of hydrothermally altered areas, which are usually associated with mineralization, is essential in mineral exploration. In this research, open source reflectance spectroscopy data from the multispectral moderate-resolution Landsat 8 satellite was used to map altered rocks in the Gauteng and Mpumalanga provinces of South Africa. The unique spectral reflectance and absorption characteristics of remotely sensed Landsat data in the visible, near-infrared (NIR), shortwave-infrared (SWIR) and thermal infrared (TIR) regions of the electromagnetic spectrum were used in different digital image processing techniques. The band ratios (red/blue, SWIR 2/NIR, SWIR 1/NIR), spectral band combinations (Kaufmann ratio, Sabins ratio) and principal component analysis (Crosta technique) were applied to efficiently and successfully map hydrothermal alteration minerals. The results showed that the combination of spectral bands and the principal component analysis method is effective in delineating mineral alteration through remotely sensed satellite data. The validation of results by using the published mineral maps of the Council for Geoscience South Africa showed a good relationship with the identified zones of mineralization. The methodology developed in this study is cost-effective and time-saving, and can be applied to inaccessible and/or new areas with limited ground-based knowledge to obtain reliable and up-to-date mineral information.IntroductionMany developing nations depend on exploration and exploitation of mineral resources to sustain their economic growth. Usually, the traditional mineral exploration techniques require enormous finances, prolonged time, and tremendous manpower, particularly in areas that are not easily reachable (Maduaka, 2014). Furthermore, mineral exploration required state-of-the-art techniques and expertise along with geological, geochemical, and geophysical datasets, which may not be easily available or may be lacking where access is problematic (Kaiser et al., 2002; Bemis et al., 2014). Modern remote sensing technology has proved to be one of the highly efficient and robust techniques used for mineral exploration. The use of remote sensing satellite images for geological mapping and mineral exploration usually involves studying the physicochemical properties of rocks and weathering soils, such as mineralogy, landforms, geochemical signatures, and the spatiall distribution of lineaments (Bhattacharya et al., 2012)."

Mar 1, 2019

By P. J. Lloyd

Society is fully justified in its concern about the environment, but that concern may, at present, be too uncritical It is, for instance, essential to establish that there is a valid environmental impact, and that there is truly a causal link between a human activity and an observed shift in environmental conditions. In establishing these, it inessential to recognize that scientific proof offers consistency, but that it can never provide completeness. Thus, no amount of scientific endeavour can ever prove that mitigation of the effects of human activity will be perfect. Society normally expresses its concern through legislation. The existing legislation in South Africa is reviewed, and it is found that [>legislation regarding water is probably too stringent to be effective, >legislation regarding air and land use is probably too lax, >all the environmental legislation is too fragmented to be efficient, and the Department of Environmental Affairs is hamstrung by inter-departmental rivalry. ] It is accordingly concluded that, if means are to be found for ensuring adequate mitigation of environmental impact in the face of ongoing economic development, it is necessary to establish a Judicial Commission on Environmental Affairs advised by, but given greater powers than, the departments currently active in environmental maters. This Commission should be charged with creating, perhaps over a decade, a body of legislation that would guide development while protecting the environment in its widest sense.

Jan 1, 1994

By K. Hodgson, J. P. M. Hojem, N. G. W. Cook

Already about one-third of South Africa's coal is mined at depths exceeding 100 metres. Almost all this mining is done by the bord and pillar method. Conventional design procedures call for ever larger pillars as depths of workings increase, resulting in the loss of large amounts of coal and reductions in productivity. Barrier pillars are in general use to ensure against large collapses. The presence of these strong pillars would allow a more efficient design of the bord and pillar layout to yield improved extraction ratios by using smaller, yielding, pillars between the bords. Knowledge of the complete load- displacement curves for such pillars is a prerequisite for the design of such a system. A 100-MN, stiff jacking system for measuring the complete load-displacement curves of pillars with cross-sections of up to 2 m X 2 m is described. The jacks are installed in a slot cut across the central plane of symmetry of a pillar, thereby ensuring that the stress distribution in the pillar during a test, especially at its contacts with the roof and floor, is identical to that caused in a similar pillar by convergence across the seam. Preliminary results in the form of complete load-displacement curves for test pillars of about 1.5 metre square section are given.

By Timo Niitti, Sami Grönstrand

n today's marketplace with high metals prices, many operations are faced with the challenge of improving recovery and at the same time maximizing availability. New operations under feasibility studies have the same requirements, with the additional need for ever higher capacities. Economies of scale have proved a vital competitive advantage in the game of ore dressing. Flotation is the most widely used method for extracting valuable minerals from ore - despite its mature age of 100 years. Customer demand has driven the development to increasing cell sizes, and in most cases, this has brought the advantages of both lower capital expenditure and lower operational and maintenance cost. The challenge of scale up, however, is to meet the metallurgical performance requirements in the larger volumes. The paper outlines recent trends and developments in flotation technology, and presents new solutions designed to address the needs for increased capacities as well as improved performance. Whether the goal is to improve existing operations or to scale up new equipment, computer aided tools are playing a key role in shortening the development cycle and reducing costly trial-and-error tests in full scale. Using the new tools and validation thereof will be outlined, as well as the development principles behind the new solutions. Plant results and experiences with the new developments are presented and discussed in several cases around the world.

Jan 1, 2007

By Y. Yang, L. Li, X. Liu

Coal mining in China is facing the transition from output to quality. Based on the total mining capacity and average production, the current situation of coal mining at mine, city, and province levels is analysed, and data in support for the layout of sustainable mining development and the optimization of output provided. The results show that 87% of China's coal is mined by underground methods, with an average production capacity of 0.93 Mt/a per mine. Open pit mining accounts for 13%, with an average mine production capacity of 5.73 Mt/a. The average mining capacity of coal mines in China is 1.05 Mt/a, with 1181 coal mines with an average capacity less than 0.3 Mt/a, accounting for 35% of the total coal mines but contributing only 4.51% to output. They are distributed in about 48 cities in six provinces, seriously restricting the transition to green coal mining. The coal industry should speed up the closure of small coal mines in key provinces and cities, eliminate outdated production capacity in the central region, increase the speed and proportion of coal resources moving westward, and promote high-quality development of coal mining.

Jan 26, 2023

By G. Akdogan, S. M. Bradshaw, M. I. Isaacs, P. Van Wyk

In the mineral processing industry, Ni-Cu-Fe-S converter matte is leached in order to remove base metals from a concentrate containing platinum group metals (PGMs). This paper investigates the atmospheric leaching process, in order to develop a better understanding of the leaching behaviour of the base metals; in particular Cu, Fe, Ni, and the PGMs in particular Ru and Ir with key process variables, acid concentration, copper concentration under oxidative leaching conditions. Higher initial acid concentration resulted in a higher copper, iron and nickel extractions, as well as higher leaching rates together with faster Cu, Ru, Ir precipitation occurring. On the other hand, a higher initial copper concentration resulted in more nickel but less iron being extracted. Keywords: PGM, converter matte, leaching, precipitation

Jan 1, 2020

DECEMBER, 1971 The Wanders Club, Johannesburg Sunday, 9th April, to Friday, 14th April, 1972 The Tenth Symposium which is the first ever held outside the North American continent is being organised by the South African Institute of Mining and Metallurgy (with the South African Council for Scientific and Industrial Research and the South African Council for Automation and Computation), in collaboration with the previous co-sponsors. '" The programme includes over 60 papers from thirteen different countries. Attendance promises to be good and interested parties who have not yet registered are earnestly requested to do so without delay. The closure date for registration application is 31st January, 1972. The objective of this symposium is to pool experience and knowledge and to discuss new and potential developments for the planning and control of mineral projects. The papers which are to be presented will indicate the progress which has been made in this direction through the successful application of operations research, mathematical, statistical and computer methods. The intention is to bring together those persons responsible for managing various operations in the mineral industry with those engaged in the development of such mathematical and computer techniques as could assist this management. All interested parties are welcome. PRE-REGISTRATION (please return enclosed form as soon as possible). Applications for registration close on January 31, 1972. The fee payable on application will be R70. Late applications may, subject to vacancies being available,

By H. G. Mosenthal

In any mining enterprise, the extraction of the ore from the orebody is of vital importance. This activity is stoping. The gold mines of the Witwatersrand and its extensions in the Klerksdorp, Welkom, and Evander areas form the most extensive goldfield in the world. This address reviews stoping technology and improvements in this technology since the end of the Second World War. Although the reefs that make up the Witwatersrand orebody are uniquely extensive, they are not suited to mechanized mining. This is due to a number of factors such as the depth of the orebody, its narrowness, and the hardness and abrasiveness of the quartzite forming the orebody. The most notable improvements in stoping technology have been brought about because of our beter understanding of rock-engineering problems. This has resulted in beter layouts, stoping geometry, systems of aleviating rock stresses, and support systems. It has enabled the industry, at ever-greater mining depths, to maintain and even increase productivity. These improvements, based on rock engineering, have significantly reduced the accidents due to rockbursts. There are many diferences between today's stoping and that practised forty years ago. Panels are shorter, concentrated mining has superseded bench mining, and the support systems are certainly better. Yet the face scraper is still used extensively, as are pneumatic rock drills. Some innovative stoping systems that have given rise to improved productivity are discussed. Explosives technology has shown spectacular advances during the period under review. Sadly, our local industry has had little to do with this research and development, but has been most adaptive in using the new products on offer.

Jan 1, 1990

By P. M. Vercruijsse

Dredging is an industry in constant transformation. It has changed tremendously in the last decades. The traditional dredging activity, like construction and maintaining ports and harbours, desilting of drainage and irrigation channels, keeping reservoirs at depths and removing sediments from waterways, is still of importance. However, it is surpassed by other applications of dredging technology. Reclamation is an important example, where large amounts of sand are dredged, transported over large distances and used to make new land for industrial, housing, airport and other infrastructural purposes. Beach nourishment and other protective measurements should be mentioned here as well. Other applications like offshore winning of oil and gas, environmental clean-up, mining of interesting minerals like gold, diamonds, titanium and tin as well as aggregates from inland and offshore deposits are of importance. For all of these dredging applications equipment is required, and with changing circumstances and constraints, the design and use altered significantly. Larger dredging depths and increasing capacities require an impressive scale-up of equipment and tools. A demand for higher accuracy and selectivity set the requirement for a higher level of automation and control in combination with a well trained crew. Operations under more difficult circumstances and with other soil characteristics necessitated the development of new dredging components and systems. A sound basis for all developments was and still is a better understanding of the various dredging processes. This paper will highlight some eye-catching developments in the dredging industry. It will focus on issues in the field of hydraulic transport such as ever increasing capacity and dredging depth, as well as the pumping of large size materials.

Jan 1, 2007

By J. P. Coetzee

Dr. K. Gebhard In his excellent and comprehensive survey on the future development of the Iron and Steel Industry in South Africa, Mr. Coetzee has also mentioned the direct reduction processes as a possible method of converting iron ore to iron. Mr. Coetzee has made it quite clear that at this stage one should not consider these processes as a 'magic formula' which herald a 'break through'. I agree entirely with this point of view. Once upon a time I held the opposite view, but in the meantime I have revised my views. To do so, I had 40 years at my disposal. In 1930 I had the privilege of being connected with the first commercial sponge iron plant in Germany1 - a plant which was capable of producing 40 tons of sponge iron a day. We were determined to prove that the blast furnace would become obsolete in the near future. We considered it as an unnecessary detour to convert iron ore first into an iron-carbon alloy, which contained further quite a number of undesirable elements, and to remove this carbon by an endothermic process. Direct iron-making seemed to be a logical short cut. Unfortunately, we were not able to establish this 'short cut,', but the life of our sponge iron plant was cut short. We had solved all technical but not the economic problems. Basically the positon is still the same today - mainly economic and to a lesser degree technological aspects determine the rate at which sponge iron plants are installed. More has been said and written than done about direct reduction plants. I think that there are two main reasons for this stagnation in the introduction of direct reduction processes. The first reason is that modern blast furnaces are just too good and too economic ever to be replaced by direct reduction processes on a large scale. This, of course, already limits the field of application for direct reduction plants. The second reason is that sponge iron production and utilisation is based on technical considerations, which increase not only the production cost of sponge iron but also the conversion cost to steel to such an extent that under special conditions only are direct reduction plants an economic proposition. Are these technical considerations still as forceful and valid today as they were when 'direct steelmaking' was first contemplated? The development of sponge iron production as a method of direct

Jan 3, 1971

By J. Jacobs

The three-product cyclone was originally developed in Russia and is now extensively used in China. The cyclone has recently entered the South African coal industry, and with the obvious advantages that this item of process equipment offers our ever-evolving industry it is safe to assume that it will add value to dense medium circuits in South Africa. Some of the possible applications include: ? Producing multiple products using a single dense medium circuit. These can typically be a primary product with calorific value of 27.50 MJ/kg and a secondary (middling) product with a calorific value of 22 MJ/kg ? High-density separation with a low circulating medium density. Anglo Thermal Coal and Exxaro have pioneered the use of these units at Umlalazi and New Clydesdale respectively. Extensive test work has been performed at Umlalazi to determine the efficiency of the unit and to determine how it compares with the conventional DSM (Dutch School of Mines) cyclone. Some people in the coal industry were initially sceptical and expected the performance of the three-product cyclone to be inferior to that of the conventional dense medium cyclone. The results of the test work have, however, shown that the efficiency of the unit is comparable to that of the cyclones currently employed. A valid concern expressed is the control over the cut-point density of the second stage separation, and work is on-going to find the optimal way to control the secondary separation density. Theoretically, the secondary separation density can be manipulated by changing the orifices of the unit, especially the spigot of the secondary stage. This remains to be proven, and a series of tests is currently being planned. Whatever the result of these tests may be, the three-product cyclone definitely has a place in the South African coal processing industry as it offers a low OPEX and CAPEX solution for producing multiple products from a single circuit, as well as the ability to operate at very high separation densities, while making use of low-density circulating medium. Keywords dense medium separation, DSM, three-product cyclone, coal processing.

Nov 1, 2013

By P. R. Jochens, D. D. Howat, C. W. Wolhuter

Prof D. D. Howat (Member): I am a man with a grievance this afternoon. The other authors of the paper entered into a conspiracy to ensure that I presented the paper, and finally even had the audacity to say that this was the least that could be expected from me as I had done so little of the other work. Looking at the distinguished audience here that includes some figures who have forgotten more about cement that some of us have ever learned, I realise how right the other authors were. I feel very much cast in the role of the fool who was pushed in where angels fear to tread. I hesitate to say, Sir, that I would not use the word angels in any definition of the authors of this paper. In presenting the paper, may I try to put forward a few simple points about cement that are probably as little known to the majority of the audience as they were to me-at least until very recently. Concrete, made by mixing Portland cement, sand, crushed rock and water is the most widely used constructional material in the world. Generally the production of actual Portland Cement is about two-thirds that of steel and by the time this is formed into concrete the total is about five times the world tonnage of steel produced. A very rough approximation suggests that world consumption of concrete is about one ton per person per annum. Apart from fresh water mankind consumes no other material in such quantities. What mankind originally required was a mortar to be used for joining blocks of stone or bricks. Such mortar was originally made from limestone burned in a kiln and then mixed with water. Production of mortar of this type began over 5,000 years ago. Some samples from pyramids in Egypt have shown this mortar to be in good condition although over 4,500 years old. The progress of technological development was very slow until 1824 when an English bricklayer, Joseph Aspidin, patented a new mortar material which he made by burning limestone and clay together in his kitchen stove. Aspdin called his product 'Portland Cement' because, in colour, it resembled a well-known building stone quarried in the Isle of Portland on the south coast of England. Aspid's same types of raw materials are used today in modern cement production and the product is still referred to as Portland cement. A lime-containing material such as chalk or shell and a clay-type material such as shale, slate or clay itself, are mixed in the required proportions, ground and fed to a kiln where the minimum burning temperature is about 1,500°C. The raw materials react to form hard chunks of a material known as 'clinker'. About 5 per cent of gypsum is added to the clinker and the mixture is then ground to a very fine powder, the function of the gypsum being to control the rate of setting of the concrete. The key oxides in cement production are lime, silica, alumina and iron oxide. The possible reactions occurring during and the products of the burning process are shown in Table I.

Jan 12, 1968

By J. N. Van der Merwe

Following the Coalbrook disaster in 1960, research into coal pillar strength resulted in the adoption of the concept of a safety factor for the design of stable pillars in South African coal mining. At the time when the original statistical analysis was performed by Salamon and Munro in the early 1960s, 27 cases of failed pillar workings were considered suitable for inclusion in the database of failed pillars. Pillar failure did not stop after the introduction of the safety factor formula by Salamon and Munro (1967). In the ensuing years, pillars that were created before the application of the formula deteriorated and later failed, as did ones that were created after the introduction of the formula. This means that over time, the database of failed pillar cases increased in size, allowing ever more reliable analyses to be performed. The number of failed cases in the database had grown from the original 27 in the 1960s to 86 by 2011. All the failed cases are contained in the updated database. The database of stable pillars, which is also used in the derivation of strength formulae, has now been extended from 125 to 337 cases. The new database of intact pillar cases is more complete as it bridges the time gap between the Salamon and Munro (1967) and the Van der Merwe (2006) databases. The original requirements for inclusion into the database were satisfied in the compilation of this latest collection. The characteristics of the original database of intact pillars did not change in a meaningful way. The mining depth and pillar dimensions of the new database are largely as they were in the original database. Time-related trends with regard to pillar dimensions and depth of mining could not be found, indicating that the geometrical parameters of coal mining in South Africa have not changed meaningfully in approximately a century of mining. The characteristics of cases in the updated database of failed pillars does not differ substantially from the one published by Van der Merwe (2006). The same difference between that database and the original Salamon and Munro database, namely that the average safety factor of the failed cases had increased dramatically, from 1.0 to 1.5, is still apparent. This may be due to the inclusion of more failures from specific areas that exhibit a disproportionate number of failures at higher safety factors. These areas are the Vaal Basin, Klip River, and Free State coalfields. The new database confirms yet again that there is no correlation between the safety factors of failed pillars and their time of failure. The safety factor on its own is thus not a reliable predictor of longterm stability of pillars. Keywords coal pillar, stable pillar cases, pillar collapse, pillar data base.

Nov 1, 2013

By C. B. Carelse, M. Manuel, D. Chetty

Automated mineralogical analysis of platinum group minerals (PGM), using the mineral liberation analyser, provides information used to understand flotation efficiency, primarily from a PGM liberation and association standpoint. To date, however, there is no consistent understanding regarding PGM speciation and its impact on floatability. Previous studies of PGM from UG2 ores concluded that a larger dataset is needed from which the various parameters can be modelled. Parameters on telluride, arsenide, sulfurarsenide and alloy species need to be integrated to fully understand the impact of PGM speciation on flotation, and for this, ores other than PGE-sulfide-rich UG2 must be assessed. Flotation rougher rate tests were performed on feed samples from two Platreef ores to determine the flotation response of individual liberated PGM species. This was achieved through automated mineralogical analysis of feed, rougher concentrates and tails. Based on 1529 liberated PGM grains assessed over the circuit for two Platreef ores, preliminary results show that PGM speciation, species grain size and competition from gangue appear to influence floatability in an ‘optimised’ laboratory environment. Keywords: PGM, PGM species, flotation, liberation

Jan 1, 2020

The first neutrinos in nature ever detected by man were "caught" in a unique laboratory some 3 km (over 2 miles) underground in one of the world's deepest mine shafts at East Rand Proprietary Mines (ERPM), Boksburg. Only 100 m from where gold is being mined from the rock face a small team of South African and American physicists work on one of the most fascinating and important fundamental research projects that is currently exciting the imagination of the scientific world. Neutrinos are sub-atomic particles just as are protons, neutrons and electrons, but they are unique in that they have neither electric charge nor mass. Cosmic neutrinos travel at the speed of light and penetrate stars and planets. Even a million kilometres of solid lead would not provide a satisfactory shield against them. Stars are believed to "burn" by means of nuclear reactions which produce enormous fluxes of neutrinos. The sun, for example, illuminates the earth with visible light, but also bathes it with neutrinos. After World War II, two American physicists, Profs Frederick Reines and Clyde Cowan, experimenting at a large nuclear reactor, succeeded in obtaining direct evidence of the existence of the laboratory-produced neutrino. It then became very important to establish whether neutrinos also existed in nature. This knowledge would lead to a greater understanding of the forces of nuclear physics, of the behaviour of nuclear particles and, indeed, is also relevant to astrophysics. From the start it was clear that the search for "natural" neutrinos would be difficult. Questions which arose were- * how could they be traced if they were without mass or electric charge? * how could other nuclear particles be screened off? * could these not be wrongly detected, or even prevent accurate detection of neutrinos? Neutrinos were known to be produced along with charged particles, by the reaction of primary cosmic rays with the constituents of the atmosphere. It was also known that when the neutrinos collided with matter, they themselves produced the same type of charged particle which could be detected if the unwanted charged particles from the atmosphere could be screened off. What was needed, therefore, was a laboratory where the particles produced in the atmosphere could be screened out, yet which would receive and detect the particles produced by the neutrons' collision with the matter (solid rock) in the vicinity of the laboratory. This meant that scientists either had to build a laboratory with an enormously thick lead shield for their detection work. . . or they could go as near as possible to the centre of the earth where only charged nuclear particles of the very highest energies could penetrate. ERPM was clearly the most suitable place in the world where so effective a "neutrino trap" could be set. Under more than 3 000 m of solid rock the apparatus for detecting neutrinos is well shielded against unwanted nuclear particles produced in the cosmic radiation which can reach the laboratory only in a steeply vertical trajectory. Other particles are easily stopped by the great thickness of rock. The air-conditioned laboratory is at one end of a 150 m long tunnel, 2,5 m high and wide, blasted from the rock. The electronic recording equipment is housed here, while the rest of the tunnel is filled with the detection system. When a charged particle passes through a detector element, it produces a minute flash of light which is recorded and which triggers a flash-tube array. This then defines the trajectory of the charged particle, which is also recorded on film for analysis. So far 82 neutrinos have been detected, 50 at the present level and 32 at a higher level, and the findings have borne out the physicists' theoretical expectations. In this joint project Profs Reines, J. P. F. Sellschop, Director of the Witwatersrand University's Nuclear Research Unit and M. F. Crouch of the Case-Western Reserve University of Ohio are the Chief Investigators. This unique endeavour has been made possible by financial support from the US Atomic Energy Commission, the University of the Witwatersrand and the Chamber of Mines of South Africa, as well as by the cooperation of the management and men of ERPM.

By L. C. Woollacott, A. K. Tripathy, J. H. Potgieter

This paper presents the second of a two part study on density stratification in a laboratory batch jig. The first study, reported elsewhere, investigated the effect of operating conditions on the stratification profile achieved at equilibrium. The study reported in this paper investigated their effect on the kinetics of density stratification under 18 different sets of operating conditions - five for binary systems with different particle densities; and 13 for a ternary system with different configurations of the jig cycle. Although the study was academic in nature (it involved simple systems of 8 mm glass beads) it has a number of practical implications. It found that the most influential operating variables affecting stratification kinetics are the amplitude of water displacement, the pulsion hold time, and, to a lesser extent, the pulsion time. It also found that reasonable rates of stratification can be expected in systems with density differences as low as 237 kg/m3 but below this the kinetics deteriorate significantly. The two studies together suggest that, within a broad range of operating conditions, the equilibrium stratification profile is independent of control variables and it is the control of stratification kinetics that has the primary influence on the quality of density separations in a jig. Keywords: Jigging kinetics, stratification, equilibrium stratification, batch jig

Jan 1, 2020

By G. A. Wiebols, N. G. W. Cook, N. C. Joughin

Discussion R. E. Rarnes (Member): The original concepts and the pioneering work now brought to the practical test stage by the Mining Research Laboratory team deserve our highest praise. The authors of this comprehensive paper rightly stress the urgency of establishing the extent to which the apparent potential can profitably be realised in practice. It is to be hoped that adequate funds will be made available by individual mining companies, the Chamber of Mines and manufacturers to attract the necessary staff and maintain the high rate of achievement of the last two years. From the Seventy-Eighth Annual Report of the Chamber of Mines and its members we see that, in 1967, with a Working Revenue of R759.8 million from gold and R54.6 million pit mouth coal sales and with profits from gold and uranium and pyrite of R307.9 million, only R1.9 million was spent by the Chamber on all forms of Research. It is considered unlikely that the associated mining companies and manufacturers exceeded this investment expenditure. Assuming a total of R4 million spent by the industry on Research and Development, this is less than half of 1 per cent of sales of gold and coal. This percentage, so low in comparison to North America and Europe, is no worse than that of Exploration expenditure which, in 1967, with South Africa's total mineral production of R1,287 million, was estimated to have been R6 million (Pretorius 1968). In a primary industry with ever present depletion of ore deposits and with cost escalation, expenditure on Exploration and on Research and Development is not a risky luxury but a tactical obligation. The potential rate of return on research expenditure into rock breaking is high. Stores consumed by gold and coal mines, members of the Chamber of Mines, totalled R316.2 million in 1967. Except for purchased power costing R42.2 million the highest cost group was explosives, drills and drill steel totalling R33.8 million or 10.7 per cent of the total stores consumed. In the paper under discussion it is claimed that the low 'effective stoping width' should greatly reduce the likelihood of rock falls or rock bursts to the extent that permanent support can be dispensed with. Insofar as this narrow cut is only 12 in. in advance of the working area which, with a 10 in. channel, is unlikely to be much reduced in width from that achieved by current methods, this claim is not readily understandable. Were it to have been based upon the regional support gained from packed waste it would have been more acceptable. Pre-developed stope drives may give serious trouble at depth and for this reason it is questioned whether a stoping area can avoid periodic sub-development blasting-the spoil and fumes from which will interfere with the rock flow and continuous mining of the rock-cutter. If, in the mining method proposed by the authors, stope drives are cut as small as possible (6 ft by 6 ft) then 25 per cent of the total tons handled (excluding resued waste) and 5 per cent of the gold will be blasted conventionally in the stope. At this stage one cannot envisage tunnelling machines economically or practically capable of such work. The various methods described by the authors and subsequent contributors for breaking waste are most interesting. It was noted that the 'bull wedge' and 'explosives' in Fig. 1 of the paper were no further from the ideal point 'A' than was 'cutting'. The writer considers that the bold and imaginative steps taken by the Mining Research Laboratory Team, the mining companies and the manufacturers concerned will eventually lead to a successful rock cutting machine with universal application largely independent of rock type. This may take many years. In the meantime other methods of improving productivity of saleable metal by rock breaking teams should be investigated even if such methods have local applications only. In 1955 the writer conducted tests with a wire saw similar to those used in quarries in the Northern Transvaal and elsewhere. Jeppestown shale, the immediate footwall of much of the East Rand gold field, was cut at the rate of 6 in. per hour using sand, water and a special endless rope driven by a low h.p. motor. A hypothesis on its application was submitted to the Office of the Government Mining Engineer in 1955 and to other mining institutions in 1966 after the writer returned to South Africa. By inference, rope sawing was classed as less promising than other methods tested in the Orange Free State Goldfields (Parker 1969). With highly resilicified hanging and footwall quartzites this was not surprising and confirmed the writers findings when testing hanging wall quartzite from the East Rand in 1955. The relatively uniform conditions, the low strength, hardness, and silica content of the Merensky Reef platinum deposits (Gray and von Bardeleben 1969) and in particular, the existence of overlying Merensky pyroxenite (Cousins 1964) make this and the East Rand attractive areas for larger scale testing of wire saws. It is envisaged that in suitable rock types the 5/8 in. slot would be advanced down dip or down a minor dip. In undisturbed areas 'faces' of up to 200 ft in length could be cut several feet in advance of breaking which could then consist of light blasting to the second free face or some of the methods now being tested for breaking waste in rock-cutting operations. A wire saw is an inexpensive and simple machine which, in some areas, could make significant and early gains in rock breaking efficiency as well as in ground and stoping width control.

Jan 5, 1968

By Peter Stacey

This presentation provides comments on the increasing challenges associated with pit slope designs from the perspective of a design reviewer. Besides the technical issues related to the significant increase in current and proposed slope heights since the primary methodology in current use for pit slope designs was developed, other factors are coming into play. These include changes in mining equipment and associated operating practices, as well as a growing awareness on the part of mining executives and other stakeholders of the significance of stable, or at least well-managed, slopes. In the latter area, the associated clarification of responsibility has led to the increased use of either in-house or independent review consultants working on the behalf of management. From a technical perspective, since the mid-1970?s there have been significant improvements in the tools, particularly analytical methods, that are available to slope designers. There is also an increased understanding of the importance of a detailed geological model, with strong emphasis on alteration and/or structure to form the platform for the slope designs. However, the basic technology for determining the rock strength aspects has changed little, although an expanding body of experience is being accumulated in its use and there is a reasonable degree of comfort in its application for slope heights of up to at least 500 m. In addition, slope management is now viewed as a critical part of the implementation of slope designs and this has been supported by continuing improvements in slope monitoring systems. In recent years safety has become a primary concern, in part as a result of some major slope failures that have attracted the attention of regulators and the public, as well as mining executives, who are being held more responsible for unsafe conditions and associated events. There is therefore a growing demand for risk assessments to replace the deterministic design approaches upon which the current design technology is largely based. The focus of mine executives on safety has undoubtedly in part facilitated the recent long overdue revitalization of research into the design and stability of large pit slopes, the requirement for which has been recognized for many years by practitioners. This research, as well as the CSIRO Large Open Pit Study, will almost certainly provide advances beyond the empirical strength determination methods such as the Hoek-Brown failure criterion, which form the basis for current rockmass strength determination. At the same time, as mentioned above, there is a growing awareness of the requirement for a detailed structural model as a major component of every large slope design. In addition, other areas requiring further research include the impact of groundwater pressures on rock mass strength, particularly in rocks with low permeabilities, and the role of stress in high open pit slopes. From the perspective of design implementation, even with the recent significant advances in metal prices, mine operators remain under pressure to minimize mining costs. To address these constraints, mining equipment of ever increasing size is being introduced. There are, however, some disadvantages to this trend in the area of slope design. For example, the large electric shovels are not well designed for scaling bench faces, nor are they cost effective in this mode. As a result, specialized equipment may be needed in the mining cycle to perform the clean-up duties, which in turn increases operating costs. Further, where the large equipment is used in minimum width pushbacks to reduce the instantaneous stripping ratio, the advance rates can be high, but at the same time the associated changes in operating procedures are often not conducive to the concurrent use of such measures as controlled blasting, careful scaling and drain hole installation that generally improve stability. The resulting conflicts which may arise between the interests of production and those of slope stability are often exacerbated by the fact that these stabilization techniques actually increase the operating costs on which the operations manager is frequently judged, even though there is an overall increase in profit. Meeting the objective of developing slope designs which are practicable , i.e., achievable in terms of every aspect of the operating constraints in the specific pit, requires interaction and compromise between the geotechnical engineer, mine planners and operating staff during the formulation of the design criteria. In the current environment, it is often no longer sufficient to present slope designs in deterministic terms to a mine planner who accepts them almost without question. Increasingly, the requirement is that they be proposed within the framework of risk levels, related both to safety and to economic outcomes, to a decision maker who may not be a technical expert in the mining field. In this context, the mine executives must have sufficient information and understanding to be able to establish acceptable levels of risk for the company and other stakeholders; in this process the slope designers must play a major role. These changing requirements for presentation of slope designs necessitate clear communication of the basis for the design, which may be very complex, so that the implications of the designs may be thoroughly understood by all concerned. To ensure clarity at this stage, the slope designer must not only quantify the uncertainty in the input parameters, including the geological model, but must also be able to communicate and defend the resulting design recommendations. Where particular designs may have high associated risks, simply because of the degree of uncertainty in the data, this must also be recognized and proposed methods of reducing the uncertainty included in the presentation. In summary, from a reviewer?s perspective slope designs must not only be technically sound, but must also address the broader context of the mining operation as a whole, taking into account such factors as safety aspects, the available equipment to implement the designs, and the acceptable risk levels for the company. In addition, the designs must be presented in a way that will allow the mine executives, who are ultimately responsible, and the operators, who implement the designs, to fully understand the basis and short-comings of the designs and the risks associated with deviation from any constraints defined by the designer. It goes without saying that there must also be a well-defined monitoring system to confirm stability and detect and manage any variations in the design model or unexpected instability.

Jan 1, 2006

The Iscor Board has given its Mining Division the authority to proceed with detail engineering and design for a Heavy Minerals Project which comprises a mine in Northern Province near Gravelote, a mine in KwaZulu/Natal near Richards Bay and a central processing complex with a beneficiation plant and smelter which will be located near Richards Bay and Empangeni.

Jan 1, 1996