Search Documents

By Benton L. Tibbetts

Comprehensive geophysical measurements were made in the Tertiary Channel gravel deposits of Badger Hill, Calif., with the refraction seismograph, gravimeter, and well logging equipment, to develop a three-dimensional physical model of the gold-bearing gravels. Tests were also made of the applicability of magnetometer and electrical resistivity techniques. Results of 14 seismic profiles revealed four distinct layers with velocities of 1,600 ft/sec for loose gravel, 5,900 ft/sec for compact gravel, 8,600 ft/sec for cemented, blue gravel, and 15,500 ft/sec for bedrock. The depth to bedrock along the middle of the channel varied from a minimum of 100 feet in the hydraulically mined pit area to a maximum of about 300 feet in the upper bench area immediately south of the pit. These geophysical methods revealed that 40 percent of the drill holes necessary to delineate the deposit could be eliminated, at a cost saving of at least 30 percent.

Jan 1, 1971

By B. W. Madsen

A nearly dormant copper sulfide pilot-scale experimental leach containing 8.7 tons of are was injected with oxygen to determine its effect on the copper-leaching rate. Prior treatment of the uncrushed 0.25-percent-copper, mine-run stripping material consisted of 461 days of acid ferric sulfate leaching, which extracted 47 percent of the total copper. The permeability of the bed had decreased, and the percolation rate had decreased from an initial 20 gallons to 0.8 gallon per square foot per day. Copper extraction had nearly stopped. After injecting oxygen into the ore column and leaching for 30 days, the percolation rate was increased to 6 gallons per square foot per day. In an additional 298 days of leaching, an additional 40.7 percent of the copper was extracted. The improved leaching after the use of oxygen is attributed to stimulated bacterial action, better oxidation, and increased permeability.

Jan 1, 1975

1. In 2003, 14,391 mining operations reported employment statistics to the Mine Safety and Health Administration (MSHA). Almost half (49%) were sand and gravel mines, followed by stone mines (30%), coal mines (14%), nonmetal mines (5%), and metal mines (2%).

Feb 1, 2005

1. In 2003, a total of 4,357 stone mining operations reported employment to the Mine Safety and Health Administration (MSHA). The major industrial classifications in stone mining are dimension stone (used for construction purposes), crushed and broken stone (aggregates), cement, and lime. • Stone mines comprised 30.3% of all mining operations. • Mines producing crushed and broken stone (n = 3,412) comprised 78.3% of all stone mining operations.

Feb 1, 2005

1. In 2003, a total of 1,972 coal mining operations reported employment to the Mine Safety and Health Administration (MSHA). Coal mines comprised 13.7% of all mining operations. • Bituminous mines comprised 92.5% (n = 1,825) and anthracite mines 7.5% (n = 147) of coal mining operations. • More than 70% of all coal mines were located in three states: Kentucky (29.0%), West Virginia (20.9%), and Pennsylvania (20.2%). • Bituminous coal mines reported the production of over 1 billion coal tons.

Feb 1, 2005

By L. D. Stewart

The main reasons for developing an induction system for signaling from the cage are, first, to increase safety, and second, to effect economies in the operation of cage and ship hoists, especially when work is being done in the shaft. To-day nearly all mines which employ safe methods have installed safety gates on cages, at the different levels, and at the collar of the shaft. Under the old system in some instances signals could only be Given from the station outside the cage, and in other cases, after the signal was given the only method whereby those riding on the cage could control its movements consisted of pulling the bell-rope hanging in the shaft, an uncertain and somewhat hazardous procedure at best. With the system herein described, however, it is possible, without opening the gates, to signal to the engineer from any place in the shaft whether or not the cage is moving, and finder the same conditions it is possible to converse with the engineer by using the telephone. In short, the cage tender has at all times an opportunity either to signal or talk to the engineer without leaving the cage.

Jan 1, 1931

By R. E. Hall

When the criterion for control of scale prevention on the evaporating surfaces is made the conditions in the concentrated boiler water, then this control becomes an exact operation amenable to an accuracy commensurate with all other operations in the boiler room. The responsibility in boiler water conditioning, however, includes more than clean surfaces. Corrosion in feed lines, economizers and the boiler is a function of the condition of the later, and must be controlled. Steam line and turbine blading deposits must be obviated by the system of conditioning. By the chemical treatment employed, the amount and character of noncondensable uses in the steam must be controlled in accordance with the intended use of the steam. All. in all, the responsibility in boiler crater conditioning ends not with the entrance of the water into the boiler but with the passage from the boiler nozzle of steam, the dryness and rarity of which are defined by the uses to be made thereof. A clearer conception of the scope of boiler water conditioning can be obtained by reference to a diagram of the surfaces (Figure 1) at which it functions. Consideration of this diagram leads to the following outline for the problems of boiler water conditioning: (a) Prevention of scale formation on surfaces (1) In contact with water but at which no evaporation occurs. (2) At which evaporation is occurring.

Jan 1, 1926

By J. D. Marchant

Solid-state electrotransport of impurities in cerium, lanthanum, and praseodymium, using a pulsed current, was investigated. The results were compared with those of using a steady current. Impurities that showed appreciable movement with the pulsed current, but not with the steady current, were as follows: Molybdenum and oxygen in cerium, aluminum, iron, and molybdenum in lanthanum. The use of a pulsed current enhances the practical application of solid-state electrotransport to remove a wider variety of impurities from the host metals.

Jan 1, 1971

By David C. Oyler, Paul B. Stubbs

The Bureau of Mines and United States Steel Corp. are conducting a joint project to monitor formation pressures at a large (23-well) coal- bed gas drainage field near Oak Grove, AL. Three monitor holes were drilled in late 1981, and pressure monitoring began in December 1981. The Bureau of Mines direct method was used to obtain gas content data from cores taken in the monitor holes. Comparison of the 1981 gas con- tent data from the monitor holes with initial gas content values obtain- ed from the production wells in 1977 indicates a 50-pct reduction in ad- sorbed gas content inside the pattern and a 29-pct reduction at one point 500 ft outside the pattern. The combination of pressure and gas content data has also allowed an in situ isotherm curve, relating the formation pressure to adsorbed gas content, to be developed for the area of the production wells. From the current rate of pressure decline (1 lbf/inz per month), the observed changes in gas content, and the isotherm curve, it appears that most of the early gas production came from within the pattern, but since 1981 (and possibly earlier) most of the gas produced has been migrating to the wells from outside the pattern area.

Jan 1, 1985

By W. R. Reed

Drilling with water has the potential to significantly reduce the respirable dust concentrations generated from small-diameter rotary drills when drilling blastholes on surface mining operations. However, water adverseky affects tri- cone drill bits commonly used in surface drilling operations, causing excessive wear and premature replacement. Consequently, dry drilling with a dust collector system has the most widespread use in the industry. Tests have been conducted by the National Institute of Occupational Safety and Health (NOSH), Pittsburgh Research Laboratory (PRL) on a newly designed device for smaller diameter drills that separates the water from the bailing air before it reaches the bit and thus provides the cost benefit of dry drilling while providing the benefit of wet drilling for dust suppression. The water that is delivered to the hole with the bailing air is separated from the air by a proprietary mechanical device that is encased in a drill sub (short section of drill rod/pipe) located immediately behind the cutting bit. A cascade cyclone and a real-time dust monitor were used to sample dust emissions from the holes. Dust concentrations and silica content were measured when drilling dry versus drilling wet. The tests show that drilling with this water separating sub can reduce both measured dust emissions from the boreholes and visible dust around the drill rig.

In this Part, we have included copies of the flip charts and overhead projector viewgraphs used in the two briefings we conducted as part of this seismic detection and location task. The first one was an overview and problem definition briefing given to the seismic consultants on September 7, 1972. The second was a formal oral presentation of study results to technical staff members of the Pittsburgh Mining and Safety Research Center on November 21, 1972.

Jan 1, 1974

By Yael Miron

Coal mines that undergo self-heatings, and specifically mines that sustain both floor heave and self-heatings, would benefit from the use of sealants to minimize air ingress to susceptible areas. The U.S. Bureau of Mines(USBM) evaluated three sealant systems for this purpose, bentonite-water mixtures, silicate gel, and guar gum gel. The guar gum-based gel was the only sealant that possessed the desired properties of elasticity, ease of preparation, adaptability to the mine, and a long life. In addition, since the gel consists mostly of water, it could quench or cool nearby heatings. Optimal formulations were determined in laboratory tests, and then tested in the USBM Safety Research Coal Mine. Two formulations resulted in stable gels that lasted for at least 12 months in the mine. Semi continuous preparation of gel using an eductor was evaluated and appears feasible. Although guar gum gel is expensive, selective use to prevent heatings in specific areas would be cost-effective, both interms of productivity and enhanced mine safety.

Jan 1, 1995

By Manuel Gomez

The mean and the standard deviation were used to describe general sulfur and ash populations as well as specific populations of these variables from one coal seam. Both the mean and the standard deviation were incorporated in the exploration process to determine the number of drill cores necessary for seam evaluation and to guide the sequential drilling plan. Probability regions were computed to establish a basis for predicting probable ranges of average sulfur and ash concentrations that may be expected upon continued or future drilling. A computerized plot program was utilized to interpolate sulfur and ash concentrations between grid points. The plot program, which is essentially a moving average technique, permits a rapid evaluation of sulfur, sulfur forms, and ash spatial distributions as a drilling program progresses sequentially. This information, in the form of contour plots, can be made available to both the mining engineer and the fuel technologist in advance of mining to outline reserves, to improve selective mining, and to anticipate preparation facilities.

Jan 1, 1972

By H. William Zeller

The Bureau of Mines performed laboratory research to determine the effects of a barium-based fuel additive on diesel particulate emissions. The test engine was typical of types used to power underground coal min-ing equipment. Test parameters consisted of baseline measurements without additive, three fuel additive concentrations, and five steady-state engine loads, all at 1,200 r/min. Additive effects on soot mass concen-tration, opacity, particle size distribution, volatile fraction, and NOx emissions were determined. Important findings are as follows: Using the manufacturer's recom-mended additive concentration increased the gravimetrically measured mass of particulate by 30 to 80 pct at four of the five steady-state load conditions. Soot measurements by optical methods did not agree with those by gravimetric techniques, for additive-treated fuels. The additive reduced volatile hydrocarbons adsorbed on filter deposits by up to 50 pet. At most engine loads, carbon particulate was also reduced. About 40 pet of the barium added to the fuel was accounted for in the exhaust. The health implications for miners were considered, but no firm conclusions were drawn or recommendations made because the results are for steady-state conditions, which may not be representative of real-world operation of diesel-powered equipment underground.

Jan 1, 1987

By J. E. Hamak

This publication contains analyses and related source data for 144 natural gas samples from 19 States. Of the total samples, 139 were collected during calendar year 1990. The remainder were collected earlier, but releases granting permission to publish were not received until 1990. All samples were obtained and analyzed as part of the U.S. Bureau of Mines investigations of the occurrences of helium in natural gases of countries with free-market economies. This survey has been conducted since 1917. The analyses were made by mass spectrometer and chromatograph.

Jan 1, 1991

By Lester G. Morrel

THE RICH and varied occurrences of metallic ores in Australia, extensive nickel deposits on New Caledonia and phosphate rock on several widely scattered small islands were important aspects of the economy of the South Pacific area. Relatively small quantities of gold and nonmetallic minerals produced in New Zealand, Fiji, and the Territory of Papua-New Guinea remained important to the domestic economies of these islands, but had little importance to overall world mineral supplies. The value of mineral commodities produced in this area in 1964 was estimated at $658 million,3 compared with $585 million in 1963. The year's greatest commodity gains were in bauxite and aluminum, beryl concentrate, manganese ore, nickel smelter products, tin, and coal. Annual increases were recorded in virtually all countries and possessions in the area except Papua-New Guinea, where the drop in output of alluvial gold accounted for a decline of about $160,000. Mineral industry activities in Australia overshadowed those in all other parts of the South Pacific in 1964. Outstanding developments were the sales contract negotiations and physical preparation for exploiting the rich iron ore discoveries in Western Australia, the initiation of domestic crude oil production, the commissioning of two new steal mills and an alumina refinery and a start on the new alumina-aluminum project based on Cape fork bauxite deposits. The principal mineral development in 1864 in New Zealand was the progress on plans of the Newzealand Steel Co. to use indigenous iron sans as the resource base for a local steel industry. In New Caledonia, additions and expansion of the nickel mining and smelting facilities continued throughout the year. Plans for extensive geophysical studies were announced by the Government Geological Departments of British Solomon Islands and Fiji.

Jan 1, 1966

This report presents test results, data evaluations, and typical system performance expectations based on wireless electromagnetic propagation measurements performed in the MAGMA Copper Company's San Manuel mine near Tuscon, Arizona during March 30 through April 2 1981. In particular, and at the Bureau's request, this work was coordinated with testing of MF prototype vehicular radios being developed by A.R.F. Products, Inc. with USBM support under Contract H0308004 as part of a system to be marketed by Mine Safety Appliance Co. This testing also employed a prototype vehicular antenna developed by Terry S. Cory, P.E. with USBM upport under previous Contract P0382223. The work was performed under USBM contract J0308012, Propagation of EM Signals in Underground Metal/Non-metal Mines. The authors wish to thank Mr. Hank Seany, Manager of Mines and Mr. Bob Zerga, Mine Superintendent who so kindly arranged for the visit. Particular thanks are given to Mr. Al Metcalf who arranged the logistical details of our underground work, and whoa forward thinking program toward improving general mine communications at MAGMA provided the test-bed context for evaluation of the prototype equipment. The authors also wish to thank Benny Jiminez, Paul Ayala, Lorenzo De La Cruz, and Kent Billhartz for their day-by-day support of the testing. Mr. Jiminez's effort was instrumental in performing the testing, and he also provided a detailed understanding of the existing multi-level, multi-frequency trolleyphone system at MAGMA. the authors are also indebted to Dr. Larry Stolarczyk of A.R.F. for numerous detailed consultations on MF technology, and who was present and participated in the majority of the testing. 1.1 GENERAL BACKGROUND ON COPPER MINING AT MAGMA the San Manuel mine is the largest copper mine in the U.S., efficiently extracting copper and molybdenum sulfide from the low-grade San Manuel ore body.This ellipsoidal ore-shell body, with major workings located 2000-3000 feet mbelow the surface, has ore shell thickness varying between 100 and 1000 feet over a longitudinal extent of some 8000 feet, and with major & minor crossectional axes of about 5000 and 2500 feet respectively. The San Manuel mine operation employs in excess of 1000 men/shift with gross ore production between 60,000 and 70,000 tons/day. The mining operation employs the block caving technique; actively being implemented on three levels (2075,2375,2675 feet for haulage, and 2015,2315,2615 product/grizzly levels). The ore haulage is largely via D.C. trolley trains to four (3A,3B,3C,3D) product shafts for skipping to the surface. An additional three shafts at two locations are used to convey men, materials, and developmental rock extractions into and out of the mine. On each haulage level, the trains carry ore an average of two miles one-way from the ore raises to the dump points. 1.2 TOPOLOGICAL BRIEF OF THE HAULAGE LEVELS The 2375 level, on which all the testing was conducted, is illustrated in

Jan 1, 1981

By Anthony T. Iannacchione

The Bureau of Mines developed data on the methane content of the Hartshorne coalbed, Haskell and Le Flore Counties, Okla. The methane content is calculated to be between 1.1 and 1.5 trillion cubic feet, based on an estimate of total coal in place of 2.4 to 3.2 billion short tons. Methane increases with depth, but the rate of increase decreases with greater depths. Degasification in advance of mining is recommended for all mines operating at depths greater than 500 feet to reduce hazards and methane explosions, decrease mine ventilation costs, and conserve the natural gas that would be otherwise wasted.

Jan 1, 1979

By John Gross

The Alaska Station of the Bureau of Mines has recently conducted tests on two tailings from black sand which had been treated previously at the Station. The results of this previous treatment have be on given in a paper entitled "Recovery of Gold from Black Sand by Classifier Concentration." The gold in these tailings was intimately united with quartz, and was so finely divided that it could not be detected with the naked eye, nor even by P&nn ing unless the material was ground. Its fineness is further shown by the assºy result, which reported only lz per cent of the gold content as "metallics", Wºorea's the assay of the original sand reported 36 per cent of the gold as "metallics." The fact that the gold was in such fine particles, closely united with quartz, precluded further recovery by amalgamation without grinding. On the other hand, the small content present, as well as the lack of grinding appliances at the placer mines of Alasia, made it necessary that the material be cheaply handled if at all. With these facts in mind the experiments described below were undertake.n.

Oct 1, 1920

By Fred C. Turin, William J. Wiehagen

This study examined musculoskeletal injury risk at four mining sites: underground coal, underground limestone, surface copper, and surface phosphate. Each site offered opportunities to investigate musculoskeletal disorder (MSD) injury risks and how those risks might be identified and categorized. The National Institute for Occupational Safety and Health (NIOSH) worked with these sites to (1) identify work activities that showed evidence of MSD injury risk, (2) examine physical risk factors that can lead to MSDs for a handful of work tasks at each site, and (3) develop a set of ideas for problem-solving to help reduce risk factors for examined work tasks. For each site, NIOSH implemented a plan that was refined over the time period of this study. The plan consisted of four steps. The first step was to use mine injury records, a musculoskeletal discomfort questionnaire, front-line supervisor interviews, and a list of management concerns to identify work groups and work activities that have significant evidence of MSD risk factors. The second step was to select work tasks for evaluation. The third step was to interview those who do the work and make observations to characterize the MSD risk factors and musculoskeletal symptoms that exist for target tasks. The final step was to conduct brainstorming sessions with workers who perform the work or have a stake in the production task. The brainstorming sessions served to identify general strategies (ideas) for reducing MSD risk factor exposures. A final report of findings was presented to mine management and workforce representatives at each site. The risk factors and ideas for improvement identified for each site were specific to the target tasks examined. These target tasks were diverse, but there were some key similarities. For instance, jobs were found at each site that required a significant amount of manual work involving the upper extremities and low back. Handling heavy and awkward objects, forceful arm and shoulder exertions, and working in awkward postures were common for a variety of jobs across the four sites.

Jan 8, 2004