Search Documents

By Manuel Gomez

This report presents low-temperature tar data from studies by the Bureau of Mines of tars produced in an externally heated (entrained state) pilot-plant-scale retort. Analytical data covering 20 low-temperature tars, derived from the. carbonization of various ranks of foreign and domestic coals, are tabulated. The character of the tar is discussed in relationship to carbonizing conditions and the rank of coal. It is seen that in carbonization techniques that employ entrainment or fluidization of the coal particle, carbonization conditions are secondary to coal rank with respect to tar-oil yields and composition. The influence of distillation conditions on recoverable yields of tar products is presented. The probable yield of commercially important chemical products, based on a ton of pure (moisture- and ash-free) coal, are predicted. INTRODUCTION Low-temperature tars produced by entrainment or fluidized carbonization techniques that employ internally heated reactors represent the most nearly primary tart produced by industrial processes. In brief, such a process involves the application of a heat gradient to the coal particle "boiling" or suspended in a turbulent state in the reactor chamber. Conditions are observed so that the coal particle remains suspended within the reaction zone by a gas stream for a time interval commensurate with maximum tar-oil yield. The heat necessary for the carbonization reaction may be obtained entirely from the hot (preheated) gas stream, or it may be derived partly from the combustion of the volatile products and char by the transport gases, usually air. The volatile material moves out of the carbonizing zone at a rate that approaches the velocity of the transport gas. Carbonizing conditions are ideal when a minimum particle residence time is obtained within the reactor at a given temperature and a maximum yield of condensable volatile matter is released. In industrial practice this objective is a compromise.

Jan 1, 1957

The object of this program was to extend the capabilities of visual paging systems both in size and function. The system developed uses the mine pager phone line for communication, monitoring, and remote control. A central station, using a minicomputer, transmits signals by phase inversion modulation of a 16,384 Hz carrier to as many as 999 remote units. The remote unit addressed returns An echo to indicate that it is functioning and, in the case of monitor units, to convey the monitor data. Magnetically latched display dis[c]s, which can be seen from both sides when posted, are used for visual paging. Lists of the addresses of posted pages, unanswered pages, and non-echoing units are prepared by the central station computer. The system was designed to be intrinsically safe and should operate for three months on a 12-volt lantern battery.

Jan 1, 1980

By Y. Miron

Previous studies at the Bureau of Mines outlined the hazards of ammonium nitrate-fuel oil (AN-FO) mixtures in the presence of pyrite-bearing ores. The recent trend in the mining industry to strengthen AN-FO by the addition of aluminum metal raised the question regarding the effect of aluminum in AN-FO in the presence of pyrite-bearing ore. Laboratory work, similar to that done previously, demonstrated that the temperature of a self-sustaining reaction in the presence of AN-FO ore-aluminum is not lower than that for a comparable AN-FO-ore mixture. However, as might be expected from known thermochemical data, once initiated, the resulting reactions between AN-FO, aluminum, and pyrite are much more vigorous than those observed for AN-FO and pyrites alone. The temperature required to produce a self-sustained reaction for the combinations tested in this study is 250°±20° F while in the previous Bureau study, reactions were noted, in some instances, at 150° F. The different pyritic ores may be the cause of this variation.

Jan 1, 1976

By M. Clair Smith

This report is one of a series describing exploration, development, mining methods, and costs at United States open-pit mines; the Bureau of Mines prepares and publishes them in cooperation with the mining companies. Their purpose is to promote development and conservation of our mineral resources by disseminating technologic information on mining methods and practices at various United States mines. The exploration, development, equipment, and mining of a large, oxidized-copper ore deposit by open-pit methods, the leaching of the ore with sulfuric acid solution, and the recovery of the copper as cement copper are described herein.

Jan 1, 1958

Develop a training program to help mine workers effectively fight small fires in underground Goal mines. Training would enable miners to make rapid judgments on whether to attempt extinguishment, and how best to use the firefighting equipment on hand. Approach Fire reports were analyzed to define and delineate physical and behavioral variables which affect firefighting activities, and to determine effective procedures for extinguishing small fires. A course was then designed to train miners in such procedures. Finally, the course was reviewed by industry experts and administered to a group of miners to determine needed revisions and to validate the course. How It Works Analysis of fire data showed that six items should be emphasized in teaching proper fire response: 1. Alertness to fire potential. 2. Immediate power cutoff. 3. Internal, external communication. 4. Teamwork in fighting fires. 5. Role of ventilation and position of men inby the fresh air side. 6. Effective use of fire suppressant materials.

Jan 1, 1983

By D. B. Taliaferro

An accurate knowledge of the water content of oil-bearing sands4/ now is recognized as an important factor in calculations of the flow of oil through the sands to producing wells and in the estimation of oil reserves. To this end the Bureau of Mines laboratories are using a method that is an adaptation of the A. S. T. M. method of determining the water content of petroleum products (1).5/ However, the apparatus and technique have been altered slightly, as described in this report, to increase the precision of the method without affecting the simplicity of procedure or speed with which determinations may be made. Until recently petroleum engineers, when estimating reserves assumed that the entire pore volume of the oil-saturated parts of producing sands was filled with oil, as it was generally thought that the oil, water, and gas in any formation had separated completely during geologic time into distinct layers because of their difference in density. In 1929 Lindthrop and Nickolaeff (12) reported experimental results from which they concluded that 22 to 30 percent of the pore volume of producing sands in the Grozay district, Russia, was filled with water when the fields were discovered. Since that time numerous investigators (5, 7, 8, 10) have found evidence of water in the sands of now oil-producing fields and old fields that never produced water with the oil.

Jan 1, 1940

By D. B. Taliaferro

An accurate knowledge of the water content of oil-bearing sands4/ now is recognized as an important factor in calculations of the flow of oil through the sands to producing wells and in the estimation of oil reserves, To this end the Bureau of Mines laboratories are using a method that is an adaptation of the A. S. T. M. method of determining the water content of petroleum products (1).5/ However, the apparatus and technique have been altered slightly, as described in this report, to increase the precision of the method without affecting the simplicity of procedure or speed with which determinations may be made. Until recently petroleum engineers, when estimating reserves assumed that the entire pore volume of the oil-saturated parts of producing sands was filled with oil, as it was generally thought that the oil, water, and gas in any formation had separated completely during geologic time into distinct layers because of their difference in density. In 1929 Lindthrop and Nickolaeff (12) reported experimental results from which they concluded that 22 to 30 percent of the pore volume of producing sands in the Grozay district, Russia, was filled with water when the fields were discovered. Since that time numerous investigators (5, 7, 8, 10) have found evidence of water in the sands of now oil-producing fields and old fields that never produced water with the oil.

Jan 1, 1940

By Francis R. Redfern

Newton's method of solving a nonlinear equation is employed to develop a least-squares acoustic emission source location method in which the spatial residuals of the location equations are minimized. These residuals, related to the distances from the least-squares source location perpendicular to the surfaces described by the location equations, permit location error to be estimated to first order along the spatial axes. The solutions obtained by this method are the best spatial solutions to the location equations in the least-squares sense. Also presented is a procedure by which the geometrical control of a transducer array can be evaluated using the rate of change of source location with fractional velocity change.

Jan 1, 1982

By C. G. Kirkpatrick

Analysis of the data produced by a wide-band, sensitive, horizontal, biaxial motion sensor has revealed several distinctive patterns before, during, and after a roof fall. The signals prior to the roof fall are similar in spectra, but one thousand times larger in amplitude, than those after the roof fall. Immediately preceding the roof fall, by two to twelve hours, five events occurred which were larger in amplitude and lower in frequency than even the large pre-roof fall background signals. An interpretation of these events is offered.

Jan 1, 1979

By John E. Kelley

Laboratory equipment, which simulates abrasive impacts between steel and minerals that might be present during pneumatic transport of coal, was used by the Bureau of Mines to characterize the potential explosion hazard of such collisions in an atmosphere of fine coal dust, air, and methane. A variety of coal mine rock materials, including sandstone, limestone, and pyrite-bearing limestone, were impacted with specimens of pipeline steel. Tests were con-ducted in atmospheres containing zero to 6.4 vol-pct methane mixed with zero to 300 mg/l coal dust. Coal dust in air alone was not ignited by abrasive impacts, but additions of as little as 1 vol-pct methane to the coal dust and air mixture resulted in ignitions. Steel impacting against sandstone caused ignitions in mixtures of coal dust, air, and methane, and the probability for ignitions increased with an increase in methane. No ignitions occurred with impacts of steel on lime-stone or pyrite-bearing limestone, even when large showers of sparks were produced. Studies of the effect of tangential collision velocity showed that no ignitions of coal dust, air, and methane occurred below 900 fpm (4.57 m/sec). Ignitions in coal-air-methane mixtures were found to be caused by a hot friction-induced smear on the impacted rock at the impact site rather than by sparks. High-speed photography was used to verify this observation.

Jan 1, 1976

By M. R. Yenchek

The U.S. Bureau of Mines has determined a method for calculating coal mine portable power cable thermal life for a specified temperature loading. This work was the culmination of a multifaceted research project involving (1) accelerated life tests of insulation and jacket materials and (2) steady-state and cyclical loading of cables. Composite Arrhenius curves were derived for common insulation and jacket materials to identify the key cable quality that precipitates thermal failure. Plots of temperature rise versus current for popular cable sizes were then referenced to develop a correspondence between cable life, based upon thermal degradation and current loading. Predictions of cable thermal life were made through integration over variable load cycles and, consequently variable operating temperatures. This procedure may have utility for both the U.S. Mine Safety and Health Administration and mining machine designers in determining the appropriate cable size for new equipment.

Jan 1, 1991

By J. C. Johnson

In situ stresses are important input data for the design of safe, stable stope layouts and extraction sequences. However, it is commonly assumed that normal and shear stress gradients in a stress field are negligible and, consequently, that stresses are uniform throughout the region of analysis. To evaluate these assumptions and to provide input data for an analysis of a shaft pillar mining plan, in situ stresses were measured at the Homestake Mine, Lead, SD, using overcoring on hollow inclusion cells and borehole deformation gauges. These measurements were used with conventional least squares, best fit data reduction schemes. The results showed that normal stresses within the shaft pillar were less than, but comparable to, those estimated from finite-element modeling. Shear stresses were an order of magnitude less than normal stresses and varied considerably from site to site. Possible causes of this variability include effects of scale, elastic moduli, anisotropy, and axial strain. Because of the variability, it is not possible to determine the magnitude of horizontal stress gradients.

Jan 1, 2010

By H. C. Brunaugh, James Westfield, R. W. Whittaker

"INTRODUCTION The purpose of this circular is to describe the sealing off of a mine fire and subsequent use of carbon dioxide gas to extinguish it.A fire of electrical origin occurred in the Valier mine of the Valier Coal Co., Valier, Franklin County, I11., on March 29, 1949, at about 1:35 p.m. It was discovered about 3:35 p.m. in 5 south west intake airway inby 1 and 2 west panels. The No. 5 southwest airway had caved, and the fire was in the top coal beneath a large fall of rock. All men, except officials, were ordered from the mine. The mine officials decided to seal the fire, and four temporary seals were erected, which isolated approximately 200 feet of 5 south west entry. The seals were completed on March 30 at 2:45 a.m., but on March 31, at 3;40 a.m,, two of them were blown out by an explosion of gas that was produced by the fire. The two seals were rebuilt, the work being completed on March 31 at 12:00 noon, but they were blown out by another gas explosion at 12:10 a.m. on April 1. It was then decided to extinguish the fire with water if possible.To accomplish this, concrete-block dams were constructed. On April 1, about 4:25 a.m., when the dams were about half completed, water was introduced into the fire area through a 2-inch pipe.On April 4, J. G, Crawford, general manager of the Valier Coal Co., notified James Westfield, chief of the Vincennes (Ind.) Branch, U. S. Bureau of Mines, by telephone of the fire in Valier mine and requested assistance to combat it. Westfield, accompanied by F. J. Smith and H. C. Brumbaugh, Federal coal-mine inspectors, went underground and inspected the seals and dams. Later, during a conference with company officials, it was decided that the concrete-block dams were not strong enough to withstand the hydrostatic pressure that would be produced by flooding the fire area. It was then decided to use carbon dioxide gas to extinguish the fire. Four seals were completed, and 5 tons of carbon dioxide gas was introduced into the fire area, which extinguished the fire."

Apr 1, 1950

By R. L. Grayson, T. Simonyi, R. A. Andrel

"The purpose or this paper is to disclose analytical, statistical, and observational results relating to mineralogy and trace elements in respirable dust samples collected from two different mines in West Virginia. Samples were taken from longwall panels, and the panels operated in different coal seams, one located in the northern part or the state and the other in the southern region. Mining conditions and equipment arrangements on the panels will be described along with dust control techniques used. Results from sample analyses are summarized with emphasis on relationships between mineralogy, trace elements and mineral particle size to worker locations. Correlations are made between micro x-ray diffraction and energy dispersive x-ray analyses for sample mineralogy.IntroductionThrough the work of many researchers worldwide, the health of coal miners in modern societies is now protected from harmful exposure to respirable coal mine dust. A vast amount of research culminated in the exposure-response model of Jacobsen, et al, (l) which has been used to establish the 2 mg/m3 exposure limit in the United States. According to the model exposure to respirable dust for 35 years at this level or less could prevent the occurrence of a clinically significant case of coal workers' pneumoconiosis (CWP) in a miner. The exposure limit, of course, must be adjusted whenever greather than five percent free silica exists in the respirable dust.The Jacobsen model was built around a mean mass concentration exposure, which generally showed the highest correlation with both incidence and progression of CWP. As Morgan, et al noted, however, the quantity of respirable dust inhaled is not the only significant factor. 2) They noted that although mass of respirable dust correlates highe.st with the incidence of CWP, it is not a causal factor. Admittedly, the insidious processes causing the disease occur at the lund cell-dust particle level."

Mar 1, 1989

By O. M. Bishop

From October 1943 to March 1944, the Bureau of Mines conducted core drilling at the Victory fluorspar mine, Hardin County, Ill. to test the Fredonia limestone and the included sub-Rosiclare sandstone zone beneath the existing stopes. Twenty-one vertical holes were drilled to an average depth of 60 feet. Ore was penetrated in six holes. Since its discovery in 1927, the Victory mine has produced approximately 5 percent of the total fluorspar mined in the United states after that date. The ore discovered in the early mine development is now exhausted, except that contained in pillars drifting to the northeast has partly developed one substantial ore body, and company drilling has indicated another nearby. The increasing need for fluorite for war use in 1943 suggested the desirability of mining the pillars, provided it could be established that no ore beds existed below the stopes or in areas to which access would be obtained through the present workings. This work describes the work accomplished during the project and presents the data obtained.

Jan 1, 1948

By N. S. Dalal, Xiaoya Sun, Xianglin Shi

"The in vivo toxicity of vanadium(V) has been found to correlate with the depletion of cellular glutathione and related non-protein thiols. With a view to understanding the mechanism for this observation, we have investigated the oxidation of glutathione, cysteine N·acetylcystcinc and pcnicil· lamine by vanadium(V), using electron spin resonance (ESR) and ESR spin trapping methodology. The spin trap used was 5,5-dimethyl-l-pyrroline I-oxide (DMPO). It is found that the oxidation of these thiols by vanadium(V) generates the corresponding thiyl radicals and vanadilim- (IV) complexes. The results suggest that free radical reactions play a significant role in the depletion of cellular thiols by vanadium(V) and hence in vanadium(V) toxicity. 1. INTRODUCTIONThis communication reports on the identification of thiyl radicals formed as intermediates in the reaction of vanadium(V) with glutathione (GSH) and related nonprotein thiols. This study was undertaken because the biochemical mechanism of vanadium toxicity is still not fully understood,. despite being a topic of current research activity [1-20). As to possible clues, it is known that vanadium is most toxic when administered in its pentavaient state [21), and that vanadium(V) administration into laboratory mice reduces cellular levels of NAD(P)H and GSH [22). While the oxidation of NAD(P)H by vanadium has been studied extensively [16-20), that of glutathione and related non-protein thiols has been paid less attention. On the other hand, GSH and related thiols are important cellular antioxidants [23). Their functions include decomposing lipid peroxides and protecting cell membranes [23-25). Thus any reduction in the cellular contents of such nonprotein thiols after vanadium exposure may result in the accumulation of lipid peroxides which might ultimately lead to tissue injury. With a view of finding the mechanism for this thiol depletion process, we have investigated reactions of non-protein thiols with vanadium(V). Particular attention has been paid to the detection of thiyl radicals, since it has been postulated [l] (but not experimentally proven) that the glutathionyl radical (GS·) might be an intermediate in the reaction between vanadium(V), NADH and GSH. We have used electron spin resonance (ESR) and ESR spin trapping methodology for investigating the reactions of GSH, cysteine, N-acetylcysteine and penicillamine with vanadium(V). The results show that the corresponding thiyl radicals are indeed formed in the one-electron reduction of vanadium(V) by all of the above mentioned thiols."

Jan 1, 1990

By Arden D. Fugate

The Federal Bureau of Mines conducted extensive studies on solid-state defluorination (laboratory scale) and tests on molten defluorination (intermediate scale) of siliceous fluorspars. The studies were made to develop a pyrohydrolytic process for liberating fluorine from offgrade fluorspars. Test results showed that more than 90 percent of the fluorine can be evolved by solid-state defluorination at 1,300° C., and more than 97 percent can be liberated by molten-state defluorination at 1,420° C. Solid-state defluorination conditions were established by conducting tests on mixtures of ceramic-grade fluorspars and high-purity silica flour. Pelletized mixtures were defluorinated under varying conditions of time, temperature, and relative concentrations of silica, calcium fluoride, and water. The effects of adding various amounts and combinations of aluminum oxide and iron oxide on defluorination were also studied. Investigations of solid-state defluorination indicates that the following two reactions are involved: 2CaF2 + 3SiO2 = 2CaSiO3 + SiF4, and CaF2 + Sio2 + H20 = CaSiO3 + 2HF, The second reaction is dominant, although significant defluorination can be achieved by the first reaction.

Jan 1, 1961

By R. E. Siemens

The Bureau of Mines sought to correlate the variation of structure-sensitive superconducting properties with microstructure in selected Cb-Hf alloys and to compare the experimental results with those predicted by the GLAG theory. Alloys in wire and rod form were evaluated by critical temperature, critical current, magnetization, resistivity measurements, and optical and electron microscopy. In the absence of an external magnetic field, the current carrying capacity of columbium was greatly reduced with addition of up to 85 wt pct Hf, but a large increase in Ic occurred for Cb-90 wt pct Hf. Favorable Ic-H behavior was observed in cold-drawn alloys containing 25 and 57 wt pct Hf. Correspondingly, a maximum in Tc occurred at 10-25 and 90 wt pct Hf. Four- or five-hour heat treatment at 600° C resulted in maximum Ic values and maximum hysteresis in magnetization. Dislocation pileup, polygonization, and fine precipitates, responsible for flux pinning, are listed in order of their effectiveness as pinning sites. Sites having an average separation of 1,500 to 3,000 A and a diameter of 1,000 A or less were most effective in influencing Ic-H and M-H behavior. The resistive critical fields increased smoothly to a maximum of 80 k0e between 60 and 65 wt pct Hf. Highfield, mixed state, reversible paramagnetism was observed in some alloys; however, the GLAG theory was in good agreement with experimental results for the majority of the composition range studied.

Jan 1, 1969

By E. J. Matson

Under the investigation for critical and strategic minerals the Kaiser mine, formerly the Baxter fluorspar property, in northeastern Mineral County, Nev., was explored. The work comprised excavating 32 trenches averaging 90 feet in length, 8 feet in width, and 1 1/2 feet in depth. The trenches were excavated across the strike of the ore body to enable the engineer to spot the diamond-drill holes; 7 such holes were drilled, aggregating 3,276 linear feet. A total of 20 core samples and 107 sludge samples was taken. The work under this program indicated that the fluorspar southwest of the deposit extended laterally and also at depth at least 250 feet below the 400-foot level. INTRODUCTION The Kaiser fluorspar deposit is in the northeastern portion of Mineral County, Nev. Mining was begun about 1928, and the property has been a consistent producer of both Acid- and Metallurgical-grade fluorspar. The mineralized zone has been developed along a strike length of about 2,000 feet and to a depth of over 700 feet along the dip.

Jan 1, 1957

By Richard D. Miller

This publication contains routine analyses and related source data for 434 gas samples from 16 States. These samples were collected during calendar year 1961 as part of the continuous survey for the occurrence of helium in natural gas conducted by the Helium Activity of the Bureau of Mines. The analyses herein were made by mass spectrometer and Frost helium apparatus. The most important helium resource discovery made during 1961 was the Table Mesa field in San Juan County, N. Mex. This field, Which has an estimated recoverable helium reserve of 850 million cubic feet, is now supplying gas containing approximately 5.4 percent helium to the Bureau of Mines Navajo Helium Plant at Shiprock, N. Mex.

Jan 1, 1964